VECTRON 6756

Product Data Sheet
Z5 Series
P/N’s 6755 & 6756
Temperature Compensated Crystal Oscillators
Features
12.800 MHz output frequency
Low Current Draw Consumption: <20 mA
Aging to <4.0 ppm for 20 years
Package: 1.0“x 1.15”x 0.395“(25.40x29.21x10.03mm)
LS TTL output
+3.3 Vdc (operable over +3.135 Vdc to +5.5 Vdc)
For use with Semtech Chip ACS8510 SETS
SONET/SDH Network Timing Sources
Computer Telephony CT-BUS
The 6755 & 6756 have been optimized to work with
the Semtech Chip ACS8510 SETS to meet the
requirements of Bell Core specification GR-1244CORE and ITU G.813.
Both units have been designed to meet the
Frequency vs Supply requirement of ±0.05 ppm over
any ±5% change in Supply from a minimum of
+3.135 Vdc to a maximum of +5.5 Vdc.
Note: Other Stability and Output Options are available.
A data sheet explaining all the Z5 series options can
be downloaded from the TCXO section of our website
at:
www.stratum3.com
6755
6756
Frequency:
12.800 MHz
12.800 MHz
Operating Temp Range:
0ºC to +70ºC
-5ºC to +50ºC
Aging:
<4.0 ppm
for 20 years
<4.0 ppm
for 20 years
Stability vs
Temperature:
±0.28 ppm
0ºC to +70ºC
±0.28 ppm
-5ºC to +50ºC
Part Number:
Stability vs Supply:
±0.05 ppm for any ±5% change in Voltage
Initial Accuracy @ +25ºC:
Supply Voltage:
±1.5 ppm Pre-Reflow
+3.3 Vdc (operable over +3.135 Vdc to +5.5 Vdc)
<20 mA (7 mA Typical)
Current (@ +3.3 Vdc):
Output:
LS TTL
Symmetry (at 50% Vdd):
60/40 to 40/60, maximum
Rise/Fall Time (10-90%):
<10 nanoseconds
<0.5 Volts, >2.5 Volts
Level "0" and "1":
Offset
100 Hz
1k Hz
10k Hz
100k Hz
Phase Noise:
(TYPICAL)
Shock:
Vibration - Sine:
Vibration - Random:
Thermal Shock:
Acceleration:
Size:
Vectron International 267 Lowell Road, Hudson, NH 03051
Phase Noise
-115 dBc/Hz
-130 dBc/Hz
-140 dBc/Hz
-155 dBc/Hz
50g, 11ms per MIL-STD-202 Method 213 Condition G
10g, 10Hz to 500Hz per MIL-STD-202 Method 204 Condition A
5.2g rms per MIL-STD-202 Method 214 Condition A
-55ºC to +85ºC per MIL-STD-202 Method 107 Condition A
50g per MIL-STD-202 Method 212 Condition A
1.00" x 1.15" x 0.395" (25.40mm x 29.21mm x 10.03mm )
Tel: 1-88-VECTRON-1
Fax: 1-888-FAX-VECTRON
.045R
.100
.100
5 places
25.40
(1.00)
29.21
(1.15)
10.16
(0.4)
20.574
(0.81)
10.033
(in.)
(0.395)
GND (760 Series)
19.05
N/C (760 Series)
(0.75)
9.525
OUT (Both Series)
(0.375)
Supply (Z5 Series)
2.54
(.100)
10.795
19.05
(.425)
6.35
(.250)
(0.75)
GND (Z5 Series)
13.97
25.4
(.550)
(1.00)
Supply (760 Series)
20.32
(.800)
GND (Z5 Series)
2.54
3.048 SQ
(.120
Vectron International 267 Lowell Road, Hudson, NH 03051
Tel: 1-88-VECTRON-1
SQ )
N/C (Both Series)
Fax: 1-888-FAX-VECTRON
(.100)
pre-heating
60 to 90 sec.
a t 1 5 0 ºC to 170ºC
reflow
20 to 40 sec.
a t > 2 0 0 ºC
Note: TCXO’
s are precision subsystems with tolerances measured to ±0.01 ppm. Non-Hermetically sealed
TCXO’
s should not be subjected to a wash process that will immerse the TCXO in solvents. NO CLEAN is the
recommended procedure. The Z5 series of TCXO’
s has been designed for pick and place reflow soldering. The
suggested reflow profile is shown above. The TCXO may be reflowed two times. Typical frequency shift as a
result of reflow is <1.0 ppm per reflow. VI recommends waiting at least two hours after reflow before measuring the
unit.
6755
(±0.28 ppm 0ºC to +70ºC)
6756
(±0.28 ppm -5ºC to +50ºC)
USA: Vectron International 267 Lowell Road, Hudson, NH 03051 . . . . .Tel: 1-88-VECTRON-1 Fax: 1-888-FAX-VECTRON
EUROPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: 49 (0) 3328 4784 17 * Fax: 49 (0) 3328 4784
30ASIA: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tel: +86 21 28909740 / 41 / 42 Fax: +86 21 28909240 / 28909999
www.vectron.com