EPCOS B41042A2108M008

Aluminum electrolytic capacitors
Alu-X product lines
Single-ended capacitors
Series/Type:
Data
Sheet
Date:
B41042
August 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the information contained therein without EPCOS’ prior express consent is prohibited.
Single-ended capacitors
Low impedance – 105 °C
Single-ended capacitors
Low impedance – 105 °C
B41042
B41042
Long-life grade capacitors
Applications
■ Professional switch mode power supplies
Features
■
■
■
■
RoHS-compatible
High C/V value
Low impedance at high frequencies
Load life of 5000 h at 105 °C
Construction
■
■
■
■
■
Radial leads
Aluminum case, fully insulated
Charge-discharge proof
Minus pole marking on the insulating sleeve
Case with safety vent from diameter 8 mm
Delivery mode
■
■
■
■
Bulk
Taped, Ammo pack
Cut
Kinked
Please read Cautions and warnings and
Important notes at the end of this document.
2
08/08
Single-ended capacitors
Low impedance – 105 °C
B41042
Specifications and characteristics in brief
Rated voltage VR
6.3 ... 80 V DC
Operating temp. range
–55 °C … +105 °C
Rated capacitance CR
(20 °C, 120 Hz)
0.47 … 15000 µF
Capacitance tolerance
±20%
Load life
(105 °C, VR, IAC,R)
2000 h for d = 5 ... 6.3 mm
3000 h for d = 8 mm
5000 h for d ≥ 10 mm
Leakage current Ileak
(20 °C, after 1 minute)
M
Requirements:
∆C/C ≤ ±25% of initial value
tan δ ≤ 2 times initial specified limit
Ileak ≤ initial specified limit
CR VR
I leak ≤ 0.03 µA ⋅ ⎛ ------- ⋅ -------⎞ or 4 µA
⎝ µF V ⎠
Dissipation factor (max.) For capacitance higher than 1000 µF add 0.02 for every increase of
(20 °C, 120 Hz)
1000 µF.
VR (V DC)
6.3
10
16
25
35
50
tan δ
0.22
0.19
0.16
0.14
0.12
0.10 0.09 0.08
63
80
Low temperature stability
(impedance ratio)
(120 Hz)
VR (V DC)
6.3 … 10
16 … 35
50 … 80
Z ( – 55 °C )
--------------------------Z ( +20 °C )
4
3
2
Shelf life
After storage for 1000 h at 105 °C, the capacitors shall meet the requirement of load life test after reforming process. After test: VR to be applied
for 30 minutes, 24 to 48 hours before measurement.
Frequency multiplier for
rated ripple current
0.47 … 27 µF
0.40
0.55
0.65
0.80
0.90
1.00
0.60
0.70
0.80
0.90
0.95
1.00
390 … 1000 µF 0.65
0.80
0.85
0.98
1.00
1.00
1200 µF
0.90
0.95
0.98
1.00
1.00
33 … 330 µF
Temperature multiplier
for rated ripple current
50 Hz 120 Hz 500 Hz 1 kHz 10 kHz 100 kHz
0.80
+70 °C
+85 °C
+105 °C
1.96
1.68
1.00
Please read Cautions and warnings and
Important notes at the end of this document.
3
08/08
Single-ended capacitors
Low impedance – 105 °C
B41042
Dimensional drawing
l
+
øb
d
a
15 min.
Minus pole
marking
5 min.
Safety vent
KAL1080-C-E
Safety vent for diameter ≥ 8 mm.
Case dimensions
d×l
mm
dmax × Imax
mm
a
mm
b
mm
× 11
5.5 × 12.5
2.0 ±0.5
0.5 ±0.1
6.3 × 11
6.8 × 12.5
2.5 ±0.5
0.5 ±0.1
5
8
× 11.5
8.5 × 13.0
3.5 ±0.5
0.6 ±0.1
10
× 12.5
11.0 × 14.0
5.0 ±0.5
0.6 ±0.1
10
× 16
11.0 × 17.5
5.0 ±0.5
0.6 ±0.1
10
× 20
11.0 × 21.5
5.0 ±0.5
0.6 ±0.1
12.5 × 20
13.5 × 22.0
5.0 ±0.5
0.6 ±0.1
12.5 × 25
13.5 × 27.0
5.0 ±0.5
0.6 ±0.1
12.5 × 31.5
13.5 × 33.5
5.0 ±0.5
0.6 ±0.1
12.5 × 35.5
13.5 × 37.5
5.0 ±0.5
0.6 ±0.1
12.5 × 40
13.5 × 42.0
5.0 ±0.5
0.6 ±0.1
16
× 25
17.0 × 27.0
7.5 ±0.5
0.8 ±0.1
16
× 31.5
17.0 × 33.5
7.5 ±0.5
0.8 ±0.1
16
× 35.5
17.0 × 37.5
7.5 ±0.5
0.8 ±0.1
16
× 40
17.0 × 42.0
7.5 ±0.5
0.8 ±0.1
18
× 35.5
19.0 × 37.5
7.5 ±0.5
0.8 ±0.1
18
× 40
19.0 × 42.0
7.5 ±0.5
0.8 ±0.1
Please read Cautions and warnings and
Important notes at the end of this document.
4
08/08
Single-ended capacitors
Low impedance – 105 °C
B41042
Overview of available types
VR (V DC)
6.3
10
16
25
Case dimensions d × l (mm)
CR (µF)
33
5
× 11
39
5
× 11
47
5
× 11
6.3 × 11
5
× 11
6.3 × 11
68
5
× 11
6.3 × 11
6.3 × 11
82
5
× 11
6.3 × 11
6.3 × 11
56
100
5
× 11
6.3 × 11
6.3 × 11
6.3 × 15
120
5
× 11
6.3 × 11
6.3 × 11
6.3 × 15
150
6.3 × 11
6.3 × 11
6.3 × 15
8
× 11.5
180
6.3 × 11
6.3 × 11
6.3 × 15
10
× 12.5
220
6.3 × 11
6.3 × 15
8
× 11.5
10
× 12.5
270
6.3 × 15
6.3 × 15
10
× 12.5
10
× 16
330
6.3 × 15
8
× 11.5
10
× 12.5
10
× 16
390
8
× 11.5
10
× 12.5
10
× 16
10
× 20
470
10
× 12.5
10
× 12.5
10
× 16
10
× 20
560
10
× 12.5
10
× 16
10
× 20
10
× 25
680
10
× 16
10
× 16
10
× 20
10
× 31.5
820
10
× 16
10
× 20
10
× 25
12.5 × 20
1000
10
× 20
10
× 20
10
× 31.5
12.5 × 25
1200
10
× 20
10
× 25
12.5 × 20
12.5 × 25
1500
10
× 25
10
× 31.5
12.5 × 25
12.5 × 31.5
1800
10
× 31.5
12.5 × 20
12.5 × 31.5
12.5 × 35.5
2200
10
× 31.5
12.5 × 25
12.5 × 31.5
12.5 × 40
2700
12.5 × 25
12.5 × 31.5
12.5 × 35.5
16
× 31.5
3300
12.5 × 25
12.5 × 35.5
12.5 × 40
16
× 35.5
3900
12.5 × 31.5
12.5 × 40
16
× 31.5
16
× 40
4700
12.5 × 35.5
16
× 31.5
16
× 35.5
18
× 40
5600
12.5 × 40
16
× 35.5
16
× 40
6800
16
× 31.5
16
× 35.5
18
× 35.5
8200
16
× 35.5
16
× 40
18
× 40
10000
16
× 40
18
× 40
12000
18
× 35.5
15000
18
× 40
Please read Cautions and warnings and
Important notes at the end of this document.
5
08/08
Single-ended capacitors
Low impedance – 105 °C
B41042
Overview of available types
VR (V DC)
35
50
63
80
Case dimensions d × l (mm)
CR (µF)
0.47
5
× 11
0.68
5
× 11
1.0
5
× 11
1.5
5
× 11
2.2
5
× 11
3.3
5
× 11
4.7
5
× 11
5
× 11
6.8
5
× 11
5
× 11
10
5
× 11
5
× 11
6.3 × 11
12
5
× 11
5
× 11
6.3 × 11
15
5
× 11
6.3 × 11
6.3 × 11
5
× 11
6.3 × 11
6.3 × 11
22
5
× 11
6.3 × 11
6.3 × 11
6.3 × 15
27
5
× 11
6.3 × 11
6.3 × 11
6.3 × 15
33
6.3 × 11
6.3 × 11
6.3 × 15
8
39
6.3 × 11
6.3 × 11
6.3 × 15
10
× 12.5
47
6.3 × 11
6.3 × 15
8
× 11.5
10
× 12.5
56
6.3 × 11
6.3 × 15
10
× 12.5
10
× 16
68
6.3 × 15
8
× 11.5
10
× 12.5
10
× 20
82
6.3 × 15
10
× 12.5
10
× 16
10
× 20
18
× 11.5
100
8
× 11.5
10
× 16
10
× 20
10
× 25
120
10
× 12.5
10
× 16
10
× 20
10
× 31.5
150
10
× 12.5
10
× 20
10
× 25
10
× 31.5
180
10
× 16
10
× 20
10
× 31.5
12.5 × 25
220
10
× 16
10
× 25
12.5 × 20
12.5 × 31.5
270
10
× 20
10
× 31.5
12.5 × 25
12.5 × 31.5
330
10
× 20
10
× 31.5
12.5 × 25
12.5 × 35.5
390
10
× 25
12.5 × 25
12.5 × 31.5
12.5 × 40
470
10
× 31.5
12.5 × 25
12.5 × 35.5
16
× 31.5
560
12.5 × 20
12.5 × 31.5
12.5 × 40
16
× 35.5
680
12.5 × 25
12.5 × 35.5
16
× 31.5
16
× 40
12.5 × 25
12.5 × 40
16
× 35.5
18
× 35.5
1000
12.5 × 31.5
16
× 31.5
16
× 40
18
× 40
1200
12.5 × 35.5
16
× 35.5
18
× 40
820
Please read Cautions and warnings and
Important notes at the end of this document.
6
08/08
Single-ended capacitors
Low impedance – 105 °C
B41042
Overview of available types
VR (V DC)
35
50
63
Case dimensions d × l (mm)
CR (µF)
1500
12.5 × 40
1800
16
× 31.5
18
× 35.5
2200
16
× 35.5
18
× 40
2700
16
× 40
3300
18
× 40
Please read Cautions and warnings and
Important notes at the end of this document.
16
× 40
7
08/08
80
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
6.3
CR
120 Hz
20 °C
µF
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
10000
12000
15000
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
Case
dimensions
d×l
mm
5
5
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
16
16
16
18
18
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 12.5
× 16
× 16
× 20
× 20
× 25
× 31.5
× 31.5
× 25
× 25
× 31.5
× 35.5
× 40
× 31.5
× 35.5
× 40
× 35.5
× 40
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
1.200
1.100
1.000
0.900
0.870
0.700
0.580
0.480
0.390
0.350
0.300
0.270
0.230
0.200
0.160
0.120
0.095
0.092
0.090
0.080
0.061
0.059
0.056
0.050
0.045
0.040
0.036
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
8
152
176
227
253
287
374
400
448
551
597
731
796
953
1022
1221
1375
1472
1592
1711
1914
2102
2373
2376
2551
2753
2825
2963
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Ordering codes
(composition see
below)
B41042A2107M***
B41042A2127M***
B41042A2157M***
B41042A2187M***
B41042A2227M***
B41042A2277M***
B41042A2337M***
B41042A2397M***
B41042A2477M***
B41042A2567M***
B41042A2687M***
B41042A2827M***
B41042A2108M***
B41042A2128M***
B41042A2158M***
B41042A2188M***
B41042A2228M***
B41042A2278M***
B41042A2338M***
B41042A2398M***
B41042A2478M***
B41042A2568M***
B41042A2688M***
B41042A2828M***
B41042A2109M***
B41042A2129M***
B41042A2159M***
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
10
CR
120 Hz
20 °C
µF
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
10000
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
Case
dimensions
d×l
mm
5
5
6.3
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
16
16
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 12.5
× 16
× 16
× 20
× 20
× 25
× 31.5
× 20
× 25
× 31.5
× 35.5
× 40
× 31.5
× 35.5
× 35.5
× 40
× 40
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
1.600
1.400
1.200
1.000
0.820
0.680
0.580
0.520
0.470
0.430
0.390
0.330
0.280
0.230
0.180
0.160
0.120
0.100
0.090
0.080
0.068
0.063
0.056
0.050
0.045
0.041
0.360
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
9
152
176
211
236
268
291
372
405
463
552
596
733
798
987
1061
1282
1443
1472
1715
1941
2184
2362
2422
2613
2682
2812
3045
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Ordering code
(composition see
below)
B41042A3686M***
B41042A3826M***
B41042A3107M***
B41042A3127M***
B41042A3157M***
B41042A3187M***
B41042A3227M***
B41042A3277M***
B41042A3337M***
B41042A3397M***
B41042A3477M***
B41042A3567M***
B41042A3687M***
B41042A3827M***
B41042A3108M***
B41042A3128M***
B41042A3158M***
B41042A3188M***
B41042A3228M***
B41042A3278M***
B41042A3338M***
B41042A3398M***
B41042A3478M***
B41042A3568M***
B41042A3688M***
B41042A3828M***
B41042A3109M***
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
16
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
Case
dimensions
d×l
mm
5
5
6.3
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
12.5
16
16
16
18
18
× 11
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 12.5
× 16
× 16
× 20
× 20
× 25
× 31.5
× 20
× 25
× 31.5
× 31.5
× 35.5
× 40
× 31.5
× 35.5
× 40
× 35.5
× 40
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
1.200
1.000
0.900
0.780
0.580
0.550
0.520
0.500
0.470
0.420
0.390
0.310
0.230
0.210
0.180
0.150
0.120
0.100
0.082
0.075
0.068
0.062
0.056
0.050
0.045
0.041
0.036
0.035
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
10
155
176
221
243
267
292
376
408
462
553
597
731
772
954
1021
1225
1411
1432
1665
1881
2015
2223
1412
2471
2585
2822
2903
3041
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Ordering code
(composition see
below)
B41042A4476M***
B41042A4566M***
B41042A4686M***
B41042A4826M***
B41042A4107M***
B41042A4127M***
B41042A4157M***
B41042A4187M***
B41042A4227M***
B41042A4277M***
B41042A4337M***
B41042A4397M***
B41042A4477M***
B41042A4567M***
B41042A4687M***
B41042A4827M***
B41042A4108M***
B41042A4128M***
B41042A4158M***
B41042A4188M***
B41042A4228M***
B41042A4278M***
B41042A4338M***
B41042A4398M***
B41042A4478M***
B41042A4568M***
B41042A4688M***
B41042A4828M***
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
25
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
33
39
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
Case
dimensions
d×l
mm
5
5
6.3
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
12.5
16
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 12.5
× 16
× 16
× 20
× 20
× 25
× 31.5
× 20
× 25
× 25
× 31.5
× 35.5
× 40
× 31.5
× 35.5
× 40
× 40
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
1.500
1.300
1.200
1.000
0.830
0.750
0.580
0.500
0.430
0.400
0.390
0.300
0.230
0.200
0.180
0.160
0.130
0.110
0.090
0.080
0.072
0.062
0.056
0.050
0.045
0.040
0.036
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
11
156
173
212
237
261
228
372
409
461
553
628
753
798
986
1021
1223
1424
1433
1661
1765
1982
2080
2361
2471
2662
2821
2965
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Ordering code
(composition see
below)
B41042A5336M***
B41042A5396M***
B41042A5476M***
B41042A5566M***
B41042A5686M***
B41042A5826M***
B41042A5107M***
B41042A5127M***
B41042A5157M***
B41042A5187M***
B41042A5227M***
B41042A5277M***
B41042A5337M***
B41042A5397M***
B41042A5477M***
B41042A5567M***
B41042A5687M***
B41042A5827M***
B41042A5108M***
B41042A5128M***
B41042A5158M***
B41042A5188M***
B41042A5228M***
B41042A5278M***
B41042A5338M***
B41042A5398M***
B41042A5478M***
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
35
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
Case
dimensions
d×l
mm
5
5
6.3
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
12.5
16
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 12.5
× 16
× 16
× 20
× 20
× 25
× 31.5
× 20
× 25
× 25
× 31.5
× 35.5
× 40
× 31.5
× 35.5
× 40
× 40
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
1.500
1.300
1.200
0.830
0.720
0.520
0.470
0.420
0.390
0.340
0.300
0.260
0.230
0.210
0.180
0.150
0.120
0.100
0.085
0.075
0.068
0.062
0.056
0.050
0.045
0.040
0.036
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
12
161
182
227
246
271
298
372
418
463
551
599
731
796
986
1061
1222
1423
1431
1663
1765
1982
2184
2362
2475
2684
2903
3041
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Ordering code
(composition see
below)
B41042A7226M***
B41042A7276M***
B41042A7336M***
B41042A7396M***
B41042A7476M***
B41042A7566M***
B41042A7686M***
B41042A7826M***
B41042A7107M***
B41042A7127M***
B41042A7157M***
B41042A7187M***
B41042A7227M***
B41042A7277M***
B41042A7337M***
B41042A7397M***
B41042A7477M***
B41042A7567M***
B41042A7687M***
B41042A7827M***
B41042A7108M***
B41042A7128M***
B41042A7158M***
B41042A7188M***
B41042A7228M***
B41042A7278M***
B41042A7338M***
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
50
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
12
15
18
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
Case
dimensions
d×l
mm
5
5
5
5
5
5
5
5
5
5
5
5
6.3
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 16
× 16
× 20
× 20
× 25
× 31.5
× 31.5
× 25
× 25
× 31.5
× 35.5
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
7.000
6.000
4.900
4.600
4.200
3.900
3.600
3.200
2.700
2.500
2.300
2.100
1.900
1.500
1.100
1.000
0.900
0.800
0.700
0.600
0.500
0.420
0.350
0.310
0.270
0.220
0.180
0.150
0.120
0.110
0.094
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
13
23
29
37
47
57
68
82
93
116
127
148
157
196
216
241
263
332
361
415
501
623
675
821
893
1045
1203
1305
1441
1506
1682
1853
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Ordering code
(composition see
below)
B41042A6474M***
B41042A6684M***
B41042A6105M***
B41042A6155M***
B41042A6225M***
B41042A6335M***
B41042A6475M***
B41042A6685M***
B41042A6106M***
B41042A6126M***
B41042A6156M***
B41042A6186M***
B41042A6226M***
B41042A6276M***
B41042A6336M***
B41042A6396M***
B41042A6476M***
B41042A6566M***
B41042A6686M***
B41042A6826M***
B41042A6107M***
B41042A6127M***
B41042A6157M***
B41042A6187M***
B41042A6227M***
B41042A6277M***
B41042A6337M***
B41042A6397M***
B41042A6477M***
B41042A6567M***
B41042A6687M***
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
50
820
1000
1200
1500
1800
2200
12.5
16
16
16
18
18
× 40
× 31.5
× 35.5
× 40
× 35.5
× 40
0.088
0.076
0.072
0.065
0.058
0.050
2017
2123
2264
2411
2463
2562
B41042A6827M***
B41042A6108M***
B41042A6128M***
B41042A6158M***
B41042A6188M***
B41042A6228M***
63
10
12
15
18
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
5
5
6.3
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
12.5
16
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 12.5
× 16
× 20
× 20
× 25
× 31.5
× 20
× 25
× 25
× 31.5
× 35.5
× 40
× 31.5
× 35.5
× 40
× 40
3.600
3.200
2.800
2.400
2.100
1.900
1.700
1.500
1.200
1.100
0.900
0.800
0.650
0.580
0.520
0.420
0.320
0.280
0.220
0.190
0.160
0.140
0.120
0.110
0.098
0.088
136
147
185
199
217
242
306
332
367
451
503
605
751
823
954
1113
1142
1345
1421
1623
1785
1952
2053
2223
2374
2511
B41042A8106M***
B41042A8126M***
B41042A8156M***
B41042A8186M***
B41042A8226M***
B41042A8276M***
B41042A8336M***
B41042A8396M***
B41042A8476M***
B41042A8566M***
B41042A8686M***
B41042A8826M***
B41042A8107M***
B41042A8127M***
B41042A8157M***
B41042A8187M***
B41042A8227M***
B41042A8277M***
B41042A8337M***
B41042A8397M***
B41042A8477M***
B41042A8567M***
B41042A8687M***
B41042A8827M***
B41042A8108M***
B41042A8128M***
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
14
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Single-ended capacitors
Low impedance – 105 °C
B41042
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
80
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
4.7
6.8
10
12
15
18
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
Case
dimensions
d×l
mm
5
5
6.3
6.3
6.3
6.3
6.3
6.3
8
10
10
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
16
16
16
18
18
× 11
× 11
× 11
× 11
× 11
× 11
× 15
× 15
× 11.5
× 12.5
× 12.5
× 16
× 20
× 20
× 25
× 31.5
× 31.5
× 25
× 31.5
× 31.5
× 35.5
× 40
× 31.5
× 35.5
× 40
× 35.5
× 40
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
8.500
5.500
3.800
3.400
3.000
2.600
2.200
2.000
1.800
1.600
1.300
1.200
1.000
0.850
0.700
0.620
0.550
0.450
0.350
0.300
0.240
0.200
0.170
0.150
0.130
0.120
0.100
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
15
92
111
152
164
189
205
226
256
307
381
410
510
636
676
839
1032
1070
1115
1433
1509
1693
1828
1902
2080
2313
2357
2518
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
Ordering code
(composition see
below)
B41042A0475M***
B41042A0685M***
B41042A0106M***
B41042A0126M***
B41042A0156M***
B41042A0186M***
B41042A0226M***
B41042A0276M***
B41042A0336M***
B41042A0396M***
B41042A0476M***
B41042A0566M***
B41042A0686M***
B41042A0826M***
B41042A0107M***
B41042A0127M***
B41042A0157M***
B41042A0187M***
B41042A0227M***
B41042A0277M***
B41042A0337M***
B41042A0397M***
B41042A0477M***
B41042A0567M***
B41042A0687M***
B41042A0827M***
B41042A0108M***
Single-ended capacitors
Taping, packing and lead configurations
B41042
Taping, packing and lead configurations of single-ended capacitors
Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows:
Lead spacing 2.0 mm (∅ d = 4 ... 5 mm)
Last 3 digits of ordering code: 016
ød
P
∆h
P0
W2
1 max.
View B
Base tape
Adhesive tape
l1
t
W
W1
W0
H
H0
D0
∆h
F
P1
B
KAL1138-D-E
Dimensions in mm
∅d
F
4 ... 5 2.0
–0.2
H
W
W0
W1
W2
P
P0
P1
l1
t
∆h
D0
18.5
18.0
7.0
9.0
3.0
12.7
12.7
5.10
1.0
0.7
1
4.0
min.
±0.5
max.
±1.0
±0.3
±0.7
max.
±0.2
±1.0
±0.2
±0.75 ±0.5
Please read Cautions and warnings and
Important notes at the end of this document.
16
08/08
Single-ended capacitors
Taping, packing and lead configurations
B41042
Lead spacing 2.5 mm (∅ d = 4 ... 6.3 mm)
Last 3 digits of ordering code: 007
ød
P
∆h
P0
∆h
View B
t
W
W0
W1
H
H0
W2
1 max.
P1
l1
D0
F
Base tape
Adhesive tape
B
KAL1074-3-E
Dimensions in mm
∅d
F
H
H0
W0
W1
W2
P
4 ... 6.3
2.5
18.5
16.0 18.0 7.0
9.0
3.0
12.7 12.7 5.10 1.0
W
P0
P1
l1
t
∆h
D0
0.7
0
4.0
Tolerance –0.2 ±0.75 ±0.5 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
Lead spacing 3.5 mm (∅ d = 8 mm)
Last 3 digits of ordering code: 006
ød
P
∆h
P0
W2
1 max.
View B
Base tape
Adhesive tape
l1
t
W
W1
W0
H
H0
D0
∆h
F
P1
B
KAL1138-D-E
Dimensions in mm
∅d
F
H
W
W0
W1
W2
P
8
3.5
18.5
18.0 10
9.0
3.0
12.7 12.7 5.10 1.0
Tolerance ±0.5 ±0.75 ±0.5 min.
Please read Cautions and warnings and
Important notes at the end of this document.
P0
P1
l1
t
∆h
D0
0.7
1
4.0
±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 max. ±0.2
17
08/08
Single-ended capacitors
Taping, packing and lead configurations
B41042
Lead spacing 5.0 mm (∅ d = 4 ... 8 mm)
Last 3 digits of ordering code: 008
ød
P
P0
∆h
∆h
View B
t
W
W1
W0
H
H0
W2
1 max.
D0
F
P1
l1
Base tape
Adhesive tape
B
KAL1075-B-E
Lead spacing 5.0 mm (∅ d = 10 mm)
Last 3 digits of ordering code: 008
ød
P
∆h
P0
∆h
View B
t
W
W0
W1
H
W2
1 max.
D0
F
P1
l1
Base tape
Adhesive tape
B
KAL1076-J-E
Dimensions in mm
∅d
F
H
H0
W
W0
W1
W2
P
P0
P1
L1
t
∆h
D0
4 ... 6.3
5.0
18.5
16
18.0 7.0
9.0
3.0
12.7 12.7 3.85 1.0
0.6
2.0
4.0
8
5.0
18.5
16
18.0 10
9.0
3.0
12.7 12.7 3.85 1.0
0.6
2.0
4.0
10
5.0
18.5
–
18.0 12.5 9.0
3.0
12.7 12.7 3.85 1.0
0.6
2.0
4.0
Tolerance
+0.6 ±0.75 ±0.5 +1.0 +1.0 ±0.5 max. ±0.5 ±0.3 ±0.7 max. +0.3 max. ±0.2
–0.2
–0.5 –0
–0.2
Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not
available.
Please read Cautions and warnings and
Important notes at the end of this document.
18
08/08
Single-ended capacitors
Taping, packing and lead configurations
B41042
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available on request.
Kinked leads
Last 3 digits of ordering code: 001
2.1±0.1
ød
1.2±0.1
l
3.2±0.1
KAL1137-5
a
ød
l
4.5±0.5
KAL1084-A
Case size d × l (mm)
a (mm)
Case size d × l (mm) a (mm)
4×7
1.5
12.5 × 16
5.0
5×7
2.0
12.5 × 20
5.0
5 × 11
2.0
12.5 × 25
5.0
6.3 × 7
2.5
12.5 × 31.5
5.0
6.3 × 11
2.5
12.5 × 35.5
5.0
6.3 × 15
2.5
12.5 × 40
5.0
8×7
3.5
16 × 20
7.5
8 × 11.5
3.5
16 × 25
7.5
8 × 15
3.5
16 × 31.5
7.5
8 × 20
3.5
16 × 35.5
7.5
10 × 12.5
5.0
16 × 40
7.5
10 × 16
5.0
18 × 20
7.5
10 × 20
5.0
18 × 25
7.5
10 × 25
5.0
18 × 31.5
7.5
10 × 31.5
5.0
18 × 35.5
7.5
18 × 40
7.5
Please read Cautions and warnings and
Important notes at the end of this document.
19
08/08
Single-ended capacitors
Taping, packing and lead configurations
B41042
Cut leads
Last 3 digits of ordering code: 002
a
ød
l
4.5±0.5
KAL1086-R
Case size d × l (mm)
a (mm)
Case size d × l (mm) a (mm)
4×7
1.5
12.5 × 16
5.0
5×7
2.0
12.5 × 20
5.0
5 × 11
2.0
12.5 × 25
5.0
6.3 × 7
2.5
12.5 × 31.5
5.0
6.3 × 11
2.5
12.5 × 35.5
5.0
6.3 × 15
2.5
12.5 × 40
5.0
8×7
3.5
16 × 20
7.5
8 × 11.5
3.5
16 × 25
7.5
8 × 15
3.5
16 × 31.5
7.5
8 × 20
5.0
16 × 35.5
7.5
10 × 12.5
5.0
16 × 40
7.5
10 × 16
5.0
18 × 20
7.5
10 × 20
5.0
18 × 25
7.5
10 × 25
5.0
18 × 31.5
7.5
10 × 31.5
5.0
18 × 35.5
7.5
18 × 40
7.5
Please read Cautions and warnings and
Important notes at the end of this document.
20
08/08
Cautions and warnings
General
Also see “Important notes” on page 23.
1
Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
2
The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its service life.
3
The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note that
the sum of the peak values of the ripple voltage and the DC operating voltage must not exceed the rated DC voltage.
4
Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
5
Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs
sufficient space around it to operate optimally. The following dimensions are recommended:
for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm;
and for d = 42 mm or more, more than 5 mm.
6
Capacitors should not be mounted with the safety vent face down on the board. Do not locate
any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result
in excess pressure and the leakage of electrolyte.
7
Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
8
The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example under direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
9
The leakage current of an aluminum electrolytic capacitor may increase after a long period
of storage. After such storage, the capacitor must be aged by applying the rated operating
voltage for 6–8 hours before use.
10
Manual soldering:
a Soldering must be performed within the specified conditions.
Bit temperature: 350 °C; application time of soldering iron: 3 seconds.
b Ensure that the soldering iron does not touch any part of the capacitor body.
Please read Cautions and warnings and
Important notes at the end of this document.
21
08/08
Cautions and warnings
11
Do not apply excessive force to the leads and terminals. Do not move the capacitor after soldering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe
the following rules to prevent undue stress to the capacitor:
a Do not tilt or bend the capacitor after soldering.
b Ensure that the terminal spacing matches the corresponding hole spacing on the PC
board.
12
The aluminum case is not insulated from the cathode. Do not place a conductor under the
aluminum capacitors on the PC board as this may cause a short circuit. The case and top of
capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink
sleeve to ensure safe usage.
13
The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.
Please read Cautions and warnings and
Important notes at the end of this document.
22
08/08
Important notes
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in case of individual agreements deviating from the foregoing for
customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
23
08/08