EPCOS B44030J0075B000

Aluminum electrolytic capacitors
Capacitors with screw terminals
Series/Type:
B44020, B44030
Date:
November 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Screw terminals Accessories
B44020
Screw terminals Accessories
Accessories for capacitors with mounting stud on capacitor base
Capacitor Thread size
diameter
Dimensional drawing
Diameter d
mm
Ordering code
Insulating plastic shoulder washer "P" similiar to DIN 41331 specifications
≤ 40 mm
M8
8.4
B44020B0001B025
> 40 mm
M12
12.5
B44020B0002B030
Insulating washer "N" made of laminated paper
≤ 40 mm
8.4
B44020A0001B025
13
B44020A0002B025
M8
M12
> 40 mm
Insulating washer made of Hostalen
51.6 mm
d1 0.5 = 51
B44020B0006B051
d2 0.5 = 31
76.9 mm
d1 0.5 = 76
B44020B0006B076
d2 0.5 = 56
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 14
B44020
Screw terminals Accessories
Capacitor Thread size
diameter
Dimensional drawing
Ordering code
Plastic cap nut "V"
≤ 40 mm
M8
width across
flats 13 mm
B44020B0005B008
> 40 mm
M12
width across
flats 17 mm
B44020A0005B012
Reinforced nylon cap nut
> 40 mm
M12
width across
flats 19 mm
B44020J0006B012
≤ 40 mm
M8
width across
flats 17 mm
B44020J0006B008
> 40 mm
M12
width across
flats 19 mm
B44020J0007B012
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 14
B44020
Screw terminals Accessories
Mounting instructions
Non-insulated mounting with cap nut
Insulated mounting with cap nut
Mounting hole diameter
Insulated mounting with DIN 439 hex nut
d ≤ 76.9 mm
d = 91 mm
Mounting hole diameter
Please read Cautions and warnings and
Important notes at the end of this document.
Mounting hole diameter
Page 4 of 14
B44030
Screw terminals Accessories
Ring clip mounting
Ring clips are primarily used for upright mounting of screw-terminal and photoflash capacitors.
The ring clips are corrosion protected and are RoHS-compatible.
It is recommended to insert an additional insulating strip between capacitor and ring clip to avoid
any risk of damage due to edges from the clip. The strip is included in delivery. For ordering code,
see the following table. Attention must be paid to any relevant regulations (e.g. VDE, BSA or UL).
dN
h1
mm
h2
Ring clip version
Ordering code
with insulating strip
B44030J0036B000
35
15
10
50
22
15
(insulating strip
length: 230 mm)
B44030J0051B000
Please read Cautions and warnings and
Important notes at the end of this document.
(insulating strip
length: 325 mm)
Page 5 of 14
B44030
Screw terminals Accessories
dN
h1
mm
h2
65
29
19
Ring clip version
Ordering code
with insulating strip
B44030J0064B000
(insulating strip
length: 420 mm)
B44030J0075B000
75
29
19
90
29
19
(insulating strip
length: 495 mm)
B44030J0090B000
Please read Cautions and warnings and
Important notes at the end of this document.
(insulating strip
length: 585 mm)
Page 6 of 14
B44030
Screw terminals Accessories
Clamp mounting
Screw-terminal capacitors without threaded stud and with a diameter ≥ 64.3 mm can also be
mounted with ring clamps. Clamp mounting offers the following advantages:
Optimum heat transfer between capacitor base and board due to pressure contact
High vibration resistance
Electrically insulated material
Dimensional drawing
1) Length depends on application.
2) The screws have to be tightened uniformly and crosswise until the fixing part rests flatly on the
board.
3) Tubular rivets included in delivery package.
Dimensions and ordering codes
Capacitor
diameter dN
d1 ±0.2
mm
b
mm
Ordering code
65 mm
87
104
B44030A0165B000
75 mm
99
116
B44030A0175B000
90 mm
112
130
B44030A0190B000
Screws are not included in the delivery package.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 14
B44030
Screw terminals Accessories
Mounting set (ring clamps)
Protects the capacitor against tilt and the
terminals from mechanical stress
Fits for different capacitor length
Electrically insulated clamping material
Dimensions and ordering codes
∅min
Capacitor
diameter dN
Ordering code
75 mm
84 mm
B44030A0375B000
90 mm
96.5 mm
B44030A0390B000
Dimensional drawing
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 14
B44020, B44030
Screw terminals Accessories
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 14
B44020, B44030
Screw terminals Accessories
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Polarity
Make sure that polar capacitors are connected
with the right polarity.
Reverse voltage
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Upper category
temperature
Maintenance
Mounting
position of screw
terminal capacitors
Mounting of
single-ended
capacitors
Robustness of
terminals
Soldering
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
11.1
"Mounting positions of
capacitors with screw
terminals"
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
11.3
not be exceeded when connecting screw
"Mounting torques"
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature 11.5
limits during soldering.
"Soldering"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 14
B44020, B44030
Screw terminals Accessories
Topic
Soldering,
cleaning agents
Passive
flammability
Active
flammability
Safety information
Reference
Chapter "General
technical information"
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Avoid external energy, such as fire or electricity.
8.1
"Passive flammability"
Avoid overload of the capacitors.
8.2
"Active flammability"
Breakdown strength Do not damage the insulating sleeve, especially
of insulating
when ring clips are used for mounting.
sleeves
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 14
Reference
Chapter "Capacitors
with screw terminals"
"Screw terminals accessories"
B44020, B44030
Screw terminals Accessories
Symbols and terms
Symbol
English
German
C
CR
CS
CS,T
Cf
d
dmax
ESL
ESR
ESRf
Capacitance
Rated capacitance
Series capacitance
Series capacitance at temperature T
Capacitance at frequency f
Case diameter, nominal dimension
Maximum case diameter
Self-inductance
Equivalent series resistance
Equivalent series resistance at
frequency f
Equivalent series resistance at
temperature T
Frequency
Current
Alternating current (ripple current)
Root-mean-square value of alternating
current
Ripple current at frequency f
Maximum permissible ripple current
Rated ripple current
Rated ripple current for base cooling
Leakage current
Operating leakage current
Case length, nominal dimension
Maximum case length (without
terminals and mounting stud)
Resistance
Insulation resistance
Balancing resistance
Temperature
Temperature difference
Ambient temperature
Case temperature
Capacitor base temperature
Time
Period
Service life (operating hours)
Kapazität
Nennkapazität
Serienkapazität
Serienkapazität bei Temperatur T
Kapazität bei Frequenz f
Gehäusedurchmesser, Nennmaß
Maximaler Gehäusedurchmesser
Eigeninduktivität
Ersatzserienwiderstand
Ersatzserienwiderstand bei Frequenz f
ESRT
f
I
IAC
IAC,rms
IAC,f
IAC,max
IAC,R
IAC,R (B)
Ileak
Ileak,op
l
lmax
R
Rins
Rsymm
T
∆T
TA
TC
TB
t
∆t
tb
Please read Cautions and warnings and
Important notes at the end of this document.
Ersatzserienwiderstand bei Temperatur T
Frequenz
Strom
Wechselstrom
Wechselstrom, Effektivwert
Wechselstrom bei Frequenz f
Maximal zulässiger Wechselstrom
Nennwechselstrom
Nennwechselstromstrom für Bodenkühlung
Ableitstrom
Ableitstrom bei Betrieb
Gehäuselänge, Nennmaß
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
Widerstand
Isolationswiderstand
Symmetrierwiderstand
Temperatur
Temperaturdifferenz
Umgebungstemperatur
Gehäusetemperatur
Temperatur des Becherbodens
Zeit
Zeitraum
Brauchbarkeitsdauer (Betriebszeit)
Page 12 of 14
B44020, B44030
Screw terminals Accessories
Symbol
V
VF
Vop
VR
VS
XC
XL
Z
ZT
tan δ
λ
ε0
εr
ω
English
Voltage
Forming voltage
Operating voltage
Rated voltage, DC voltage
Surge voltage
Capacitive reactance
Inductive reactance
Impedance
Impedance at temperature T
Dissipation factor
Failure rate
Absolute permittivity
Relative permittivity
Angular velocity; 2 π f
German
Spannung
Formierspannung
Betriebsspannung
Nennspannung, Gleichspannung
Spitzenspannung
Kapazitiver Blindwiderstand
Induktiver Blindwiderstand
Scheinwiderstand
Scheinwiderstand bei Temperatur T
Verlustfaktor
Ausfallrate
Elektrische Feldkonstante
Dielektrizitätszahl
Kreisfrequenz; 2 π f
Notes
All dimensions are given in mm.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 14
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
Page 14 of 14