KOA X5R0603ET

TN-196 R12
1/25/07
9:45 AM
Page 1
KOA SPEER ELECTRONICS, INC.
TN-196 R12
AHA 1/25/07
Ceramic Chip Capacitors
Type NPO, X5R, X7R, Y5V
CERTIFIED
CERTIFIED
1.
General
1-1 Range of Application
This document applies to miniaturized ceramic chip capacitors for applications in circuits of electronic devices.
2.
Type Designation
The type designation shall be the following form:
New Type
3.
NPO
0805
H
T
TD
101
K
Dielectric
Size
Voltage
Termination
Material
Packaging
Capacitance
Code
Tolerance
NPO
X5R
X7R
Y5V
0402
0603
0805
1206
1210
T: Sn
TP: 7" 2mm pitch
(0402 only)
TD: 7" paper tape
TE: 7" embossed plastic
TDB: 13" paper tape
TEB: 13" embossed plastic
NPO, X5R, X7R,
Y5V - 2 significant
digits + no. of
zeros. R indicates
decimal point.
A
C
E
H
I
J
K
= 10V
= 16V
= 25V
= 50V
= 100V
= 200V
= 6.3V
Dimensions and Construction
Table 1
Case
Code
L
W
0402
t
0603
d
d
0805
Ceramic
Body
1206
1210
B
C
D
F
G
J
K
M
Z
= ±0.1pF
= ±0.25pF
= ±0.5pF
= ±1%
= ±2%
= ±5%
= ±10%
= ±20%
= +80%, -20%
Dimensions in inches (mm)
L
W
t (Max.)
d
.040 ± .004
(1.00 ± .10)
.063 ± .006
(1.60 ± .15)
.079 ± .008
(2.01 ± .20)
.126 ± .008
(3.20 ± .20)
.126 ± .008
(3.20 ± .20)
.020 ± .004
(.50 ± .10)
.032 ± .006
(.81 ± .15)
.049 ± .008
(1.25 ± .20)
.063 ± .008
(1.60 ± .20)
.098 ± .008
(2.50 ± .20)
.021
(.55)
.035
(.90)
.051
(1.30)
.059
(1.50)
.067
(1.70)
.010 ± .006
(.25 ± .15)
.014 ± .006
(.35 ± .15)
.020 ± .010
(.50 ± .25)
.020 ± .010
(.50 ± .25)
.020 ± .010
(.50 ± .25)
Solder
Plating (Sn)
Ni
Plating
Electrodes
Silver
Metallization
PAGE 1 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 2
KOA SPEER ELECTRONICS, INC.
TN-196 R12
4.
Terminations
Standard Nickel Barrier
■ Solder Plated
■
5.
Applications and Ratings
Dielectric
Capacitance Capacitance
Range
Tolerance*
Voltage
Ratings
Dissipation
Factor
NPO
0.47pF 0.039µF
.47pF~8.2pF=
C:±0.25pF
5.6pF~8.2pF=
D±0.5pF
10pF~10000pF=
F:±1%,
G:±2%,
J:±5%
X5R
0.068µF 10µF
K: ±10%
6.3V
10V
6.3 = 7.3%
10 = 5.0%
100pF 4.7µF
K: ±10%
10V
16V
25V
50V
100V
200V
For 50 &
100 volts
2.5% max.
2200pF 10µF
Z: +80, -20%
10V
16V
25V
50V
16V & 25V
= 7.0%
X7R
Y5V
16V
25V
50V
100V
200V
Operating
Temperature
Insulation
Resistance
-55°C
to
+125°C
+25°C 100,000MΩ min.
or 1000 MΩ - µF min.
whichever is less
±15% (0 VDC) 1.0 ± 0.2 Vrms
-55°C
to
+85°C
+25°C 100,000MΩ min.
or 500 MΩ - µF min.
whichever is less
±15% (0 VDC) 1.0 ± 0.2 Vrms
-55°C
to
+125°C
+25°C 100,000MΩ min.
or 1000 MΩ - µF min.
whichever is less
+22% to -82%
1.0 ± 0.2 Vrms
max.
-30°C
to
+85°C
+25°C 10,000MΩ min.
or 1000 MΩ - µF min.
whichever is less
T.C.C.
Test Voltage
For Values
>30pF: 0.1%
max., ≤30pF:
0 ± 30 ppm/°C 1.0 ± 0.2 Vrms
Q = 400 + 20 x C
DF = 1/Q
C is in pF
25 = 3.0%
16 = 3.5%
50V = 5.0%
* Special tolerances available, please consult factory.
PAGE 2 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 3
KOA SPEER ELECTRONICS, INC.
TN-196 R12
6.
NPO Capacitance Voltage Availability
Size
Capacitance values
pF
µF Cap. Code
0.47
0.56
0.68
0.82
1
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
12
15
18
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
10000
12000
15000
18000
22000
27000
33000
39000
.0001
.00012
.00015
.00018
.00022
.00027
.00033
.00039
.00047
.00056
.00068
.00082
.0010
.0012
.0015
.0018
.0022
.0027
.0033
.0039
.0047
.0056
.0068
.0082
.010
.012
.015
.018
.022
.027
.033
.039
0402*
WVDC
16
(C)
25
(E)
0805
0603*
50
(H)
100
(I)
50
(H)
50
(H)
100
(I)
1206
200
(J)
50
(H)
1210
100
(I)
200
(J)
■
200
(J)
R47
R56
R68
R82
1R0
1R2
1R5
1R8
2R2
2R7
3R3
3R9
4R7
5R6
6R8
8R2
100
120
150
180
220
270
330
390
470
560
680
820
101
121
151
181
221
271
331
391
471
561
681
821
102
122
152
182
222
272
332
392
472
562
682
822
103
123
153
183
223
273
333
393
* IR and vapor phase solder only recommended
Capacitance tolerance available: .47pF~8.2pF = C: ±0.25pF, 5.6pF~8.2pF = D: ±0.5pF
10pF~10000pF = F: ±1%, G: ±2%, J: ±5%
Bolivar Drive
50
(H)
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
PAGE 3 OF 13
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 4
KOA SPEER ELECTRONICS, INC.
TN-196 R12
7.
X5R Capacitance Voltage Availability
Size
0402
Capacitance values
pF
µF
6.3
(K)
10
(A)
0603
16
(C)
6.3
(K)
10
(A)
16
(C)
0805
25
(E)
6.3
(K)
10
(A)
1206
16
(C)
25
(E)
6.3
(K)
10
(A)
1210
16
(C)
25
(E)
6.3
(K)
10
(A)
100
150
220
330
470
680
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
0.010
0.012
0.015
0.018
0.022
0.027
0.033
0.039
0.047
0.056
0.068
0.082
0.10
0.12
0.15
0.18
0.22
0.27
0.33
0.47
0.56
0.68
0.82
1.0
1.2
1.5
1.8
2.2
3.3
4.7
6.8
10
22
47
100
Capacitance tolerance available: ±10%
PAGE 4 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 5
KOA SPEER ELECTRONICS, INC.
KOA SPEER
TN-196 R12
8.
X7R Capacitance Voltage Availability
0402*
Size
Capacitance values
pF
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
10000
12000
15000
18000
22000
27000
33000
39000
47000
56000
68000
82000
100000
120000
150000
180000
220000
270000
330000
390000
470000
560000
680000
1000000
1200000
1500000
1800000
2200000
3900000
4700000
10
µF
Cap. Code (A)
.0001
101
.00012
121
.00015
151
.00018
181
.00022
221
.00027
271
.00033
331
.00039
391
.00047
471
.00056
561
.00068
681
.00082
821
.0010
102
.0012
122
.0015
152
.0018
182
.0022
222
.0027
272
.0033
332
.0039
392
.0047
472
.0056
562
.0068
682
.0082
822
.010
103
.012
123
.015
153
.018
183
.022
223
.027
273
.033
333
.039
393
.047
473
.056
563
.068
683
.082
823
.100
104
.120
124
.150
154
.180
184
.220
224
.270
274
.330
334
.390
394
.470
474
.560
564
.680
684
1.00
105
1.20
125
1.50
155
1.80
185
2.20
225
3.90
395
4.70
475
0603*
0805
1206
1210
16 25 50 10 16 25 50 10 16 25 50 100 200 10 16 25 50 100 200 50 100 200
(C) (E) (H) (A) (C) (E) (H) (A) (C) (E) (H) (I) (J) (A) (C) (E) (H) (I) (J) (H) (I) (J)
* IR and vapor phase solder only recommended
Capacitance tolerance available: ±10%
PAGE 5 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 6
KOA SPEER ELECTRONICS, INC.
TN-196 R12
9.
Y5V Capacitance Voltage Availability
0402*
Size
Capacitance values
pF
2200
2700
3300
3900
4700
5600
6800
8200
10000
12000
15000
18000
22000
27000
33000
39000
47000
56000
68000
82000
100000
120000
150000
180000
220000
270000
330000
390000
470000
560000
680000
820000
1000000
1200000
1500000
1800000
2200000
2700000
3300000
3900000
4700000
5600000
6800000
10000000
22000000
µF
.0022
.0027
.0033
.0039
.0047
.0056
.0068
.0082
.010
.012
.015
.018
.022
.027
.033
.039
.047
.056
.068
.082
.100
.120
.150
.180
.220
.270
.330
.390
.470
.560
.680
.820
1.0
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
10
22
Cap. Code
222
272
332
392
472
562
682
822
103
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
394
474
564
684
824
105
125
155
185
225
275
335
395
475
565
685
106
226
10
(A)
16
(C)
0603*
10
(A)
16
(C)
25
(E)
0805
50
(H)
10
(A)
16
(C)
1206
25
(E)
50
(H)
10
(A)
16
(C)
25
(E)
50
(H)
* IR and vapor phase solder only recommended
Capacitance tolerance available: +80, -20%
PAGE 6 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 7
KOA SPEER ELECTRONICS, INC.
KOA SPEER
TN-196 R12
10. Typical Impedance Characteristics - NPO
Variation of Impedance with Cap Value
Impedance vs. Frequency
0805 - C0G (NP0)
10 pF vs. 100 pF vs. 1000 pF
Δ Capacitance vs. Frequency
100,000
+2
% Δ Capacitance
Impedance, Ω
10,000
1,000
100
10 pF
10.0
+1
0
-1
-2
1.0
1kHz
10 kHz
100 pF
1000 pF
0.1
1
100
10
100 kHz
1 MHz
10 MHz
Frequency
1000
Frequency, MHz
Insulation Resistance (Ohm-Farads)
% Δ Capacitance
Temperature Coefficient
Typical Capacitance Change
Envelope: 0 ± 30 ppm/°C
+0.5
0
-0.5
-55 -35 -15 +5 +25 +45 +65 +85 +105 +125
Insulation Resistance vs Temperature
10,000
1,000
100
0
Temperature °C
+25
+40
+60
+80
+100
Temperature °C
Variation of Impedance with Ceramic Formulation
Impedance vs. Frequency
1000 pF - C0G (NP0) vs X7R
0805
Variation of Impedance with Chip Size
Impedance vs. Frequency
1000 pF - C0G (NP0)
10
10.00
1206
0805
1812
1210
X7R
NPO
Impedance, Ω
Impedance, Ω
+20
1.0
0.1
10
100
1.00
0.10
0.01
10
1000
100
Frequency, MHz
1000
Frequency, MHz
PAGE 7 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 8
KOA SPEER ELECTRONICS, INC.
TN-196 R12
11. Typical Impedance Characteristics - X5R
Insulation Resistance (Ohm-Farads)
Temperature Coefficient
+20
%Δ Capacitance
+15
+10
+5
0
-5
-10
-15
-20
-60
-40
-20
0
+20 +40 +60 +80
Insulation Resistance vs Temperature
10,000
1,000
100
0
Temperature °C
+20
+25
+40
+60
+80
+100
Temperature °C
PAGE 8 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 9
KOA SPEER ELECTRONICS, INC.
KOA SPEER
TN-196 R12
12. Typical Impedance Characteristics - X7R
Variation of Impedance with Cap Value
Impedance vs. Frequency
1,000 pF vs. 10,000 pF - X7R
0805
Δ Capacitance vs. Frequency
10.00
1,000 pF
+20
% Δ Capacitance
Impedance, Ω
10,000 pF
1.00
0.10
0.01
10
100
+10
0
-10
-20
1000
1kHz
10 kHz
100 kHz
Frequency, MHz
Insulation Resistance (Ohm-Farads)
Temperature Coefficient
+12
%Δ Capacitance
+6
0
-6
-12
-18
-24
-75
-50
-25
0
10 MHz
+25 +50 +75 +100 +125
Insulation Resistance vs Temperature
10,000
1,000
100
0
Temperature °C
+20
+40
+25
+60
+80
+100
Temperature °C
Variation of Impedance with Chip Size
Impedance vs. Frequency
100,000 pF - X7R
Variation of Impedance with Chip Size
Impedance vs. Frequency
10,000 pF - X7R
10
10
1206
0805
1210
Impedance, Ω
Impedance, Ω
1 MHz
Frequency
1.0
0.1
.01
1
100
10
1206
0805
1210
1.0
0.1
.01
1,000
1
10
Frequency, MHz
100
1,000
Frequency, MHz
PAGE 9 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 10
KOA SPEER ELECTRONICS, INC.
TN-196 R12
13. Typical Impedance Characteristics - Y5V
0.1 μF - 0603
Impedance vs. Frequency
0.22 μF - 0805
Impedance vs. Frequency
10,000
1,000
1,000
Impedance (Ω)
Impedance (Ω)
100
10
1
0.1
100
10
1
0.1
0.01
10,000
100,000
1,000,000
0.01
10,000
10,000,000
100,000
Insulation Resistance (Ohm-Farads)
% Δ Capacitance
Temperature Coefficient
+20
+10
0
-10
-20
-30
-40
-50
-60
-70
-80
-55
-35 -15
10,000,000
1,000,000
Frequency (MHz)
Frequency (MHz)
+5 +25 +45 +65 +85 +105 +125
Temperature °C
Insulation Resistance vs. Temperature
10,000
1,000
100
0
+20
+30
+40
+50
+60
+70
+80 +85
Temperature °C
1 μF - 1206
Impedance vs. Frequency
Capacitance Change
vs. DC Bias Voltage
1,000
+40
+20
Δ c/c (%)
Impedance (Ω)
100
10
1
0
-20
-40
-60
0.1
-80
0.01
10,000
100,000
1,000,000
-100
0
10,000,000
20
40
60
80
100
DC Bias Voltage
Frequency (MHz)
PAGE 10 OF 13
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 11
KOA SPEER ELECTRONICS, INC.
TN-196 R12
14. Tape and Reel Quantities
All tape and reel specifications are in compliance with RS481.
Dimensions in inches (mm)
0402
0603
0805
1206
1210
TE = 7" (178) Plastic
N/A
N/A
*2,000/4,000
2,000
*2,000/4,000
B = 13" (330) Plastic
N/A
N/A
10,000
10,000
10,000
15,000
4,000
4,000
4,000
4,000
N/A
10,000
10,000
10,000
10,000
T = 7" (178) Paper
D = 13" (330) Paper
* Z5U 0805 50V≥ 104pf = 2k, 1206 50V≥ 184pf = 2k, 1210 50V≥ 274pf = 2k;
Y5V 0805 50V≥ 124pf = 2k, 25V≥ 394pf = 2k, 16V≥ 474pf = 2k, 1206 25V≥ 564pf = 2k, 16V≥ 824pf = 2k, 1210 50V≥ 334pf = 2k, 25V≥ 105pf = 2k;
X7R 0805 100V≥ 123pf = 2k, 50V≥ 101pf = 2k, 16V≥ 154pf = 2k, 1206 100V≥ 393pf = 2k, 25V≥ 124pf = 2k, 16V≥ 394pf = 2k;
NPO 0805 100V≥ 391pf = 2k, 50V≥ 561pf = 2k, 1206 100V≥ 152pf = 2k, 50V≥ 152pf = 2k, 1210 100V≥ 182pf = 2k, 50V≥ 272pf = 2k
0805 Y5VCTE 225 Z , 1206 Y5VCTE 335 Z, 1210 Y5VETE 475 Z = 3k
15. Reel Dimensions
W3 (Includes flange
distortion at
outer edge).
1.575 (40) min.
Access hole at
slot location.
W2 (Measured at hub).
B*
(Arbor hole dia.)
C
D*
A
N (Hub dia.)
Full radius*
W1 (Measured at hub).
Tape slot in core
for tape start.
0.98 (2.5) min. width,
.394 (10) min. depth.
* Drive spokes optional. If used,
asterisked dimensions apply.
Dimensions in inches (mm)
Tape
Size(1)
A
Max.
8mm
7.0
(178)
12mm
B*
Min.
D*
Min.
C
N
Min.
W2
Max.
W1
± .050
.059
(1.5)
.512 ± .008
(13.0 ± 0.20)
.795
(20.2)
.331 - 0.0
(8.4 ±- 1.0
0.0 )
1.969
(50)
± .078
12.992
(330)
.488 - 0.0
(12.4 ±- 2.0
0.0 )
.567
14.4
.724
(18.4)
Metric dimensions will govern.
English measurements rounded and for reference only.
(1) For tape sizes 16mm and 24mm (used with chip size 3 3640) consult EIA RS-481 latest revision.
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
W3
.311
(7.9 Min.)
.429
(10.9 Max.)
.469
(11.9 Min.)
.607
(15.4 Max.)
PAGE 11 OF 13
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 12
KOA SPEER ELECTRONICS, INC.
TN-196 R12
10 pitches cumulative
tolerance on tape
±0.008 (±0.2)
16. Carrier Tape Specifications
Embossed plastic
8 & 12mm
T2
T
P0
Deformation
between
embossments
Embossment
P2
D0
E
G1
See note 3
A0
B1
K0
Top
cover
tape
F
W
B0
T1
G2
See note 4
P1
Center lines
of cavity
For tape feeder reference
only including draft
concentric around B0
D1 for components
.079 x .047 (2.0 x 1.2)
and larger
Maximum cavity
size, see note 1
User direction of feed
17. Dimensions
Dimensions in inches (mm)
Tape Size
Constant
D0
.059
(1.5
8mm
and
12mm
Tape Size
Variable
±
±
-
E
P0
P2
.004
0.0
0.10
0.0
.069 ± .004 .157 ± .004 .079 ± .002
) (1.75 ±0.10) (4.0 ± 0.10) (2.0 ± 0.05)
B1
Max.
See note 6
D1
Min.
See note 5
F
T Max.
T1
G1
G2
.024
(0.600)
.004
(0.10)
Max.
.030
(0.75)
Min.
See note 3
.030
(0.75)
Min.
See note 4
T2
W
A0B0K0
R
Min.
See note 2
P1
8mm
.179
(4.55)
.039
(1.0)
.138 ± .002 .157 ± .004
(3.5 ± 0.05) (4.0 ± 0.10)
.984
(25)
.098
(2.5 Max.)
12mm
.323
(8.2)
.059
(1.5)
.217 ± .002 .157 ± .004
(5.5 ± 0.05) (4.0 ± 0.10)
1.181
(30)
.256
(6.5 Max.)
.315
(8.0
±
±
-
.012
.004
0.3
0.1
)
See note 1
.472 ± .012
(12.0 ± .30) See note 1
Notes:
1. A0, B0 and K0 are determined by the max. dimensions to the ends of the terminals extending from the components body and/or the body of the
component. The clearance between the end of the terminals of the body of the components to the sides and depth of the cavity (A0, B0 and K0)
must be within .002" (0.05)mm min. and .020" (0.50)mm max. The clearance allowed must also prevent rotation of the component within the
cavity of not more than 20 degrees (see examples A & B).
2. Tape with components shall pass around radius "R" without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to
provide R min. for .472" (12)mm embossed tape for reels with hub diameters approaching N min. (Table 4).
3. G1 dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
4. G2 dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape
between the embossed cavity or to the edge of the cavity whichever is less.
5. The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment
location and hole location shall be applied independent of each other.
20° Maximum Component Rotation
6. B1 dimension is a reference dimension for tape feeder clearance only.
20°
Typical component
cavity center line
BO
Maximum Component Rotation
Side or Front Sectional View
Example "A"
Typical component
center line
AO
Top View Example "B"
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
PAGE 12 OF 13
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
TN-196 R12
1/25/07
9:45 AM
Page 13
KOA SPEER ELECTRONICS, INC.
TN-196 R12
10 pitches cumulative
tolerance on tape
±0.008 (±0.2)
18. Carrier Tape Specifications
Punched paper tape
8 & 12mm
P2
D0
T
P0
E
F
Top
cover
tape
Bottom
cover
tape
T1
T1
W
B0
G1
A0
Cavity size,
see note 1
P1
G2
Center lines
of cavity
User direction of feed
19. Dimensions
Dimensions in inches (mm)
Tape Size
Constant
8mm
and
12mm
Tape Size
Variable
D0
.059 ±-
.004
.000
(1.5 ±- 0.1
0.0 )
E
P0
P2
T1
G1
G2
R MIN
.069 ± .004
(1.75 ±0.10)
.157 ± .004
(4.0 ± 0.10)
.079 ± .002
(2.0 ± 0.05)
.004
(0.10)
Max.
.030
(0.75)
Min.
.030
(0.75)
Min.
.984
(25)
See note 2
P1
F
W
A0B0
T
See note 1
See note 2
8mm
.157 ± .004
(4.0 ± 0.10)
.138 ± .002
(3.5 ± 0.05)
.315 ±- .012
.004
(8.0 ±- 0.3
)
0.1
12mm
.157 ± .004
(4.0 ± .010)
.217 ± .002
(5.5 ± 0.05)
.472 ± .012
(12.0 ± 0.3)
Notes:
1. A0, B0 and T are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions
of the component. The clearance between the ends of the terminals or body of the components to the sides and depth of the cavity (A0, B0
and T) must be within .002" (0.05) mm min. and .020" (0.50) mm max. The clearance allowed must also prevent rotation of the component
within the cavity of not more than 20 degrees (see examples C & D).
20° Maximum Component Rotation
2. Tape with components shall pass
around radius "R" without damage.
T
Typical component
3. .043" (1.1) mm base tape and .063" (1.6) mm max.
20°
cavity center line
B
for non-paper base compositions.
O
Maximum Component Rotation
Side or Front Sectional View
Example "C"
AO
Typical component
center line
Top View Example "D"
20. Recommended Land Pattern Dimensions
Component pads should be designed to achieve good solder filets and minimize component movement during reflow soldering.
Pad dimensions are given below for multilayer ceramic capacitors for both reflow and wave soldering. The basis for these designs is:
• Pad width equal to component width. It is permissible to decrease this to as low as 85% of component width but it is not advisable to go below this.
• Pad overlap 0.5mm beneath component
• Pad extension 0.5mm beyond components
for reflow and 1.0mm for wave soldering
C
D
22-2 Wave Soldering
22-1 Reflow Soldering
Case Size
0402
0603
0805
1206
1210
C
A
A*
0.50
0.75
1.25
1.60
2.50
B*
1.70
2.30
3.00
4.00
4.00
C*
0.60
0.80
1.00
1.00
1.00
D*
0.50
0.70
1.00
2.00
2.00
Case Size A*
0805
1.25
1206
1.60
1210
2.50
B*
C*
D*
4.00 1.50 1.00
5.00 1.50 2.00
5.00 1.50 2.00
B
PAGE 13 OF 13
* All dimensions are in millimeters unless otherwise specified.
Bolivar Drive
■
P.O. Box 547
■
Bradford, PA 16701
■
USA
■
814-362-5536
■
Fax 814-362-8883
■
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.