TI MOC3020

MOC3020 THRU MOC3023
OPTOCOUPLERS/OPTOISOLATORS
SOES025 – OCTOBER 1986 – REVISED OCTOBER 1995
•
•
•
•
•
•
•
•
250 V Phototriac Driver Output
Gallium-Arsenide-Diode Infrared Source and
Optically-Coupled Silicon Traic Driver
(Bilateral Switch)
UL Recognized . . . File Number E65085
High Isolation . . . 7500 V Peak
Output Driver Designed for 220 V ac
Standard 6-Terminal Plastic DIP
Directly Interchangeable with
Motorola MOC3020, MOC3021, MOC3022,
and MOC3023
Direct Replacements for:
– TRW Optron OPI3020, OPI3021,
OPI3022, and OPI3023;
– General Instrument MCP3020,
MCP3021, and MCP3022;
– General Electric GE3020,
GE3021, GE3022, and GE3023
MOC3020 – MOC3023 . . . PACKAGE
(TOP VIEW)
ANODE
CATHODE
NC
1
6
2
5
3
4
MAIN TERM
TRIAC SUB†
MAIN TERM
† Do not connect this terminal
NC – No internal connection
logic diagram
1
6
2
4
absolute maximum ratings at 25°C free-air temperature (unless otherwise noted)†
Input-to-output peak voltage, 5 s maximum duration, 60 Hz (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . 7.5 kV
Input diode reverse voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 V
Input diode forward current, continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Output repetitive peak off-state voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 V
Output on-state current, total rms value (50-60 Hz, full sine wave): TA = 25°C . . . . . . . . . . . . . . . . . . . 100 mA
TA = 70°C . . . . . . . . . . . . . . . . . . . . 50 mA
Output driver nonrepetitive peak on-state current (tw = 10 ms, duty cycle = 10%, see Figure 7) . . . . . . 1.2 A
Continuous power dissipation at (or below) 25°C free-air temperature:
Infrared-emitting diode (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW
Phototriac (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 mW
Total device (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 mW
Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 100°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C
Lead temperature 1,6 (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Input-to-output peak voltage is the internal device dielectric breakdown rating.
2. Derate linearly to 100°C free-air temperature at the rate of 1.33 mW/°C.
3. Derate linearly to 100°C free-air temperature at the rate of 4 mW/°C.
4. Derate linearly to 100°C free-air temperature at the rate of 4.4 mW/°C.
Copyright  1995, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7–1
MOC3020 THRU MOC3023
OPTOCOUPLERS/OPTOISOLATORS
SOES025 – OCTOBER 1986 – REVISED OCTOBER 1995
electrical characteristics at 25°C free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IR
VF
Static reverse current
VR = 3 V
IF = 10 mA
I(DRM)
dv/dt
Repetitive off-state current, either direction
dv/dt(c)
Static forward voltage
See Note 5
Critical rate of rise of off-state voltage
V(DRM) = 400 V,
See Figure 1
Critical rate of rise of commutating voltage
IO = 15 mA,
See Figure 1
MIN
TYP
MAX
UNIT
0.05
100
µA
MOC3021
I
i
Input
trigger
current,
either direction
MOC3022
Peak on-state voltage, either direction
V
100
nA
O
supply
l voltage
l
Output
=3V
ITM = 100 mA
Holding current, either direction
V/µs
0.15
MOC3023
VTM
IH
1.5
10
100
MOC3020
IFT
1.2
V/µs
15
30
8
15
5
10
3
5
1.4
3
100
A
mA
V
µA
NOTE 5: Test voltage must be applied at a rate no higher than 12 V/µs.
PARAMETER MEASUREMENT INFORMATION
VCC
1
6
VI = 30 V rms
2
4
RL
10 kΩ
Input
(see Note A)
2N3904
NOTE A. The critical rate of rise of off-state voltage, dv/dt, is measured with the input at 0 V. The frequency of Vin is increased until the
phototriac turns on. This frequency is then used to calculate the dv/dt according to the formula:
ń + 2 Ǹ2πfVin
dv dt
The critical rate of rise of commutating voltage, dv/dt(c), is measured by applying occasional 5-V pulses to the input and increasing
the frequency of Vin until the phototriac stays on (latches) after the input pulse has ceased. With no further input pulses, the
frequency of Vin is then gradually decreased until the phototriac turns off. The frequency at which turn-off occurs may then be used
to calculate the dv/dt(c) according to the formula shown above.
Figure 1. Critical Rate of Rise Test Circuit
7–2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MOC3020 THRU MOC3023
OPTOCOUPLERS/OPTOISOLATORS
SOES025 – OCTOBER 1986 – REVISED OCTOBER 1995
TYPICAL CHARACTERISTICS
EMITTING-DIODE TRIGGER CURRENT (NORMALIZED)
vs
FREE-AIR TEMPERATURE
ON-STATE CHARACTERISTICS
800
600
I TM – Peak On-State Current – mA
1.3
1.2
1.1
1
0.9
0.8
– 50
400
Output tw = 800 µs
IF = 20 mA
f = 60 Hz
TA = 25°C
200
0
– 200
– 400
– 600
– 25
0
25
50
75
– 800
–3
100
TA – Free-Air Temperature – °C
–2
–1
0
1
2
VTM – Peak On-State Voltage – V
Figure 2
3
Figure 3
NONREPETITIVE PEAK ON-STATE CURRENT
vs
PULSE DURATION
I TSM – Nonrepetitive Peak On-State Current – mA
Emitting-Diode Trigger Current (Normalized)
1.4
3
TA = 25°C
2
1
0
0.01
10
0.1
1
tw – Pulse Duration – ms
100
Figure 4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7–3
MOC3020 THRU MOC3023
OPTOCOUPLERS/OPTOISOLATORS
SOES025 – OCTOBER 1986 – REVISED OCTOBER 1995
APPLICATIONS INFORMATION
RL
MOC3020, MOC3023
Rin
1
VCC
180 Ω
6
220 V, 60 Hz
2
RL
4
Figure 5. Resistive Load
ZL
MOC3020, MOC3023
Rin
1
VCC
6
180 Ω
2.4 kΩ
0.1 µF
2
220 V, 60 Hz
4
IGT ≤ 15 mA
Figure 6. Inductive Load With Sensitive-Gate Triac
Rin
VCC
ZL
MOC3020, MOC3023
1
6
180 Ω
1.2 kΩ
0.2 µF
2
220 V, 60 Hz
4
15 mA < IGT < 50 mA
Figure 7. Inductive Load With Nonsensitive-Gate Triac
7–4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MOC3020 THRU MOC3023
OPTOCOUPLERS/OPTOISOLATORS
SOES025 – OCTOBER 1986 – REVISED OCTOBER 1995
MECHANICAL INFORMATION
Each device consists of a gallium-arsenide infrared-emitting diode optically coupled to a silicon phototriac
mounted on a 6-terminal lead frame encapsulated within an electrically nonconductive plastic compound. The
case can withstand soldering temperature with no deformation and device performance characteristics remain
stable when operated in high-humidity conditions.
9,40 (0.370)
8,38 (0.330)
6
5
4
1
2
3
Index Dot
(see Note B)
C
L
C
L
7,62 (0.300) T.P.
(see Note A)
5,46 (0.215)
2,95 (0.116)
6,61 (0.260)
6,09 (0.240)
105°
90°
0,305 (0.012)
0,203 (0.008)
1,78 (0.070)
0,51 (0.020)
(see Note C)
1,78 (0.070) MAX
6 Places
Seating Plane
1,01 (0.040) MIN
3,81 (0.150)
3,17 (0.125)
2,03 (0.080)
1,52 (0.060)
4 Places
2,54 (0.100) T.P.
(see Note A)
0,534 (0.021)
0,381 (0.015)
6 Places
NOTES: A. Leads are within 0,13 (0.005) radius of true position (T.P.) with maximum material condition and unit installed.
B. Pin 1 identified by index dot.
C. Terminal connections:
1. Anode (part of the infrared-emitting diode)
2. Cathode (part of the infrared-emitting diode)
3. No internal connection
4. Main terminal (part of the phototransistor)
5. Triac Substrate (DO NOT connect) (part of the phototransistor)
6. Main terminal (part of the phototransistor)
D. The dimensions given fall within JEDEC MO-001 AM dimensions.
E. All linear dimensions are given in millimeters and parenthetically given in inches.
Figure 8. Mechanical Information
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7–5
7–6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor
product or service without notice, and advises its customers to obtain the latest version of relevant information
to verify, before placing orders, that the information being relied on is current.
TI warrants performance of its semiconductor products and related software to the specifications applicable at
the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are
utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each
device is not necessarily performed, except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or
severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED
TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI
products in such applications requires the written approval of an appropriate TI officer. Questions concerning
potential risk applications should be directed to TI through a local SC sales office.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards should be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein. Nor does TI warrant or represent that any license, either
express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property
right of TI covering or relating to any combination, machine, or process in which such semiconductor products
or services might be or are used.
Copyright  1995, Texas Instruments Incorporated