April 2008
FDD8882 / FDU8882
N-Channel PowerTrench® MOSFET
30V, 55A, 11.5mΩ
tm
Features
General Description
! rDS(ON) = 11.5mΩ, VGS = 10V, ID = 35A
This N-Channel MOSFET has been designed specifically to
improve the overall efficiency of DC/DC converters using
either synchronous or conventional switching PWM
controllers. It has been optimized for low gate charge, low
rDS(ON) and fast switching speed.
! rDS(ON) = 15mΩ, VGS = 4.5V, ID = 35A
! High performance trench technology for extremely low
rDS(ON)
! Low gate charge
! High power and current handling capability
RoHS Complicant
Application
! DC/DC converters
D
D
G
S
D-PAK
TO-252
(TO-252)
©2008 Fairchild Semiconductor Corporation
FDD8882/FDU8882 Rev. C
I-PAK
(TO-251AA)
G
S
G D S
1
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
2
Symbol
VDSS
Drain to Source Voltage
Parameter
Ratings
30
Units
V
VGS
Gate to Source Voltage
±20
V
55
A
Drain Current
Continuous (TC = 25oC, VGS = 10V) (Note 1)
ID
Continuous (TC =
25oC,
VGS = 4.5V) (Note 1)
Continuous (Tamb = 25oC, VGS = 10V, with RθJA = 52oC/W)
Pulsed
EAS
A
41
mJ
Power dissipation
55
W
0.37
W/oC
-55 to 175
oC
Derate above 25oC
TJ, TSTG
Operating and Storage Temperature
A
A
Figure 4
Single Pulse Avalanche Energy (Note 2)
PD
50
12.6
Thermal Characteristics
RθJC
Thermal Resistance Junction to Case TO-252, TO-251
2.73
o
C/W
RθJA
Thermal Resistance Junction to Ambient TO-252, TO-251
100
o
C/W
RθJA
Thermal Resistance Junction to Ambient TO-252, 1in2 copper pad area
52
oC/W
Package Marking and Ordering Information
Device Marking
FDD8882
Device
FDD8882
Package
TO-252AA
Reel Size
13”
Tape Width
12mm
Quantity
2500 units
FDU8882
FDU8882
TO-251AA
N/A (Tube)
N/A
75 units
F
F
Electrical Characteristics TC = 25°C unless otherwise noted
Symbol
Parameter
Test Conditions
Min
Typ
Max
Units
Off Characteristics
BVDSS
Drain to Source Breakdown Voltage
IDSS
Zero Gate Voltage Drain Current
IGSS
Gate to Source Leakage Current
ID = 250µA, VGS = 0V
VDS = 24V
VGS = 0V
TC = 150oC
VGS = ±20V
30
-
-
V
-
-
1
-
-
250
µA
-
-
±100
nA
-
2.5
V
On Characteristics
VGS(TH)
rDS(ON)
Gate to Source Threshold Voltage
Drain to Source On Resistance
FDD8882/FDU8882 Rev. C
VGS = VDS, ID = 250µA
1.2
ID = 35A, VGS = 10V
-
0.0094 0.0115
ID = 35A, VGS = 4.5V
-
0.0130 0.0150
ID = 35A, VGS = 10V,
TJ = 175oC
-
0.0150 0.0190
2
Ω
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
Absolute Maximum Ratings TC = 25°C unless otherwise noted
CISS
Input Capacitance
COSS
Output Capacitance
CRSS
Reverse Transfer Capacitance
RG
Gate Resistance
Qg(TOT)
Total Gate Charge at 10V
-
1260
-
-
240
-
pF
-
140
-
pF
VGS = 0.5V, f = 1MHz
-
2.4
-
Ω
VGS = 0V to 10V
-
22
33
nC
-
11.7
17.6
nC
-
1.2
1.8
nC
VDS = 15V, VGS = 0V,
f = 1MHz
Qg(5)
Total Gate Charge at 5V
VGS = 0V to 5V
Qg(TH)
Threshold Gate Charge
VGS = 0V to 1V
Qgs
Gate to Source Gate Charge
Qgs2
Gate Charge Threshold to Plateau
Qgd
Gate to Drain “Miller” Charge
Switching Characteristics
VDD = 15V
ID = 35A
Ig = 1.0mA
pF
-
3.7
-
nC
-
2.5
-
nC
-
4.6
-
nC
(VGS = 10V)
tON
Turn-On Time
-
-
135
ns
td(ON)
Turn-On Delay Time
-
8
-
ns
tr
Rise Time
td(OFF)
Turn-Off Delay Time
tf
tOFF
-
82
-
ns
-
40
-
ns
Fall Time
-
25
-
ns
Turn-Off Time
-
-
98
ns
ISD = 35A
-
-
1.25
V
ISD = 15A
-
-
1.0
V
VDD = 15V, ID = 35A
VGS = 10V, RGS = 13Ω
Drain-Source Diode Characteristics
VSD
Source to Drain Diode Voltage
trr
Reverse Recovery Time
ISD = 35A, dISD/dt = 100A/µs
-
-
32
ns
QRR
Reverse Recovered Charge
ISD = 35A, dISD/dt = 100A/µs
-
-
21
nC
Notes:
1: Package current limitation is 35A.
2: Starting TJ = 25°C, L = 0.1mH, IAS = 28A, VDD = 27V, VGS = 10V.
3
FDD8882/FDU8882 Rev. C
3
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
Dynamic Characteristics
60
CURRENT LIMITED
BY PACKAGE
1.0
ID, DRAIN CURRENT (A)
POWER DISSIPATION MULTIPLIER
1.2
0.8
0.6
0.4
40
20
0.2
VGS = 10V
0
0
0
25
50
75
100
150
125
175
25
50
75
TC , CASE TEMPERATURE (oC)
100
125
150
175
TC, CASE TEMPERATURE (oC)
Figure 1. Normalized Power Dissipation vs Case
Temperature
Figure 2. Maximum Continuous Drain Current vs
Case Temperature
2
DUTY CYCLE - DESCENDING ORDER
0.5
0.2
0.1
0.05
0.02
0.01
ZθJC, NORMALIZED
THERMAL IMPEDANCE
1
PDM
0.1
t1
t2
SINGLE PULSE
NOTES:
DUTY FACTOR: D = t1/t2
PEAK TJ = PDM x ZθJC x RθJC + TC
0.01
10-5
10-4
10-3
10-2
10-1
100
101
t, RECTANGULAR PULSE DURATION (s)
Figure 3. Normalized Maximum Transient Thermal Impedance
600
TC = 25oC
IDM, PEAK CURRENT (A)
TRANSCONDUCTANCE
MAY LIMIT CURRENT
IN THIS REGION
FOR TEMPERATURES
ABOVE 25oC DERATE PEAK
CURRENT AS FOLLOWS:
175 - TC
I = I25
150
VGS = 4.5V
100
30
10-5
10-4
10-3
10-2
10-1
100
101
t, PULSE WIDTH (s)
Figure 4. Peak Current Capability
FDD8882/FDU8882 Rev. C
4
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
Typical Characteristics TC = 25°C unless otherwise noted
500
IAS, AVALANCHE CURRENT (A)
ID, DRAIN CURRENT (A)
1000
10µs
100
100µs
10
OPERATION IN THIS
AREA MAY BE
LIMITED BY rDS(ON)
1ms
1
SINGLE PULSE
TJ = MAX RATED
TC = 25oC
10ms
If R = 0
tAV = (L)(IAS)/(1.3*RATED BVDSS - VDD)
If R ≠ 0
tAV = (L/R)ln[(IAS*R)/(1.3*RATED BVDSS - VDD) +1]
100
STARTING TJ = 25oC
10
STARTING TJ = 150oC
DC
0.1
1
1
0.001
60
10
0.01
VDS, DRAIN TO SOURCE VOLTAGE (V)
Figure 5. Forward Bias Safe Operating Area
10
100
Figure 6. Unclamped Inductive Switching
Capability
80
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
VDD = 15V
60
40
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
VGS = 10V
ID, DRAIN CURRENT (A)
ID , DRAIN CURRENT (A)
1
NOTE: Refer to Fairchild Application Notes AN7514 and AN7515
80
TJ = 25oC
20
TJ = 175oC
VGS = 4.5V
60
VGS = 3.5V
40
VGS = 3V
20
o
TJ = -55 C
TC = 25oC
0
0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
0
VGS , GATE TO SOURCE VOLTAGE (V)
0.5
1.0
1.5
2.0
2.5
VDS , DRAIN TO SOURCE VOLTAGE (V)
Figure 7. Transfer Characteristics
Figure 8. Saturation Characteristics
1.8
20
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
ID = 35A
NORMALIZED DRAIN TO SOURCE
ON RESISTANCE
rDS(ON), DRAIN TO SOURCE
ON RESISTANCE (mΩ)
0.1
tAV, TIME IN AVALANCHE (ms)
16
12
ID = 1A
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
1.6
1.4
1.2
1.0
0.8
VGS = 10V, ID = 35A
0.6
8
2
4
6
8
-80
10
0
40
80
120
160
200
TJ, JUNCTION TEMPERATURE (oC)
VGS, GATE TO SOURCE VOLTAGE (V)
Figure 9. Drain to Source On Resistance vs Gate
Voltage and Drain Current
FDD8882/FDU8882 Rev. C
-40
Figure 10. Normalized Drain to Source On
Resistance vs Junction Temperature
5
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
Typical Characteristics TC = 25°C unless otherwise noted
1.10
1.2
NORMALIZED DRAIN TO SOURCE
BREAKDOWN VOLTAGE
NORMALIZED GATE
THRESHOLD VOLTAGE
VGS = VDS, ID = 250µA
1.0
0.8
0.6
ID = 250µA
1.05
1.00
0.95
0.90
0.4
-80
-40
0
40
80
120
160
-80
200
-40
TJ, JUNCTION TEMPERATURE (oC)
Figure 11. Normalized Gate Threshold Voltage vs
Junction Temperature
40
80
120
160
200
Figure 12. Normalized Drain to Source
Breakdown Voltage vs Junction Temperature
3000
VGS , GATE TO SOURCE VOLTAGE (V)
10
CISS = CGS + CGD
C, CAPACITANCE (pF)
0
TJ , JUNCTION TEMPERATURE (oC)
1000
COSS ≅ CDS + CGD
CRSS = CGD
VGS = 0V, f = 1MHz
100
VDD = 15V
8
6
4
WAVEFORMS IN
DESCENDING ORDER:
ID = 35A
ID = 5A
2
0
0.1
1
10
30
0
VDS , DRAIN TO SOURCE VOLTAGE (V)
10
15
20
25
Qg, GATE CHARGE (nC)
Figure 13. Capacitance vs Drain to Source
Voltage
FDD8882/FDU8882 Rev. C
5
Figure 14. Gate Charge Waveforms for Constant
Gate Current
6
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
Typical Characteristics TC = 25°C unless otherwise noted
VDS
BVDSS
tP
L
VDS
VARY tP TO OBTAIN
IAS
+
RG
REQUIRED PEAK IAS
VDD
VDD
-
VGS
DUT
tP
IAS
0V
0
0.01Ω
tAV
Figure 15. Unclamped Energy Test Circuit
Figure 16. Unclamped Energy Waveforms
VDS
VDD
Qg(TOT)
VDS
L
VGS
VGS = 10V
VGS
Qg(5)
+
Qgs2
VDD
VGS = 5V
DUT
VGS = 1V
Ig(REF)
0
Qg(TH)
Qgs
Qgd
Ig(REF)
0
Figure 17. Gate Charge Test Circuit
Figure 18. Gate Charge Waveforms
VDS
tON
tOFF
td(ON)
td(OFF)
RL
tr
VDS
tf
90%
90%
+
VGS
VDD
-
10%
10%
0
DUT
90%
RGS
VGS
VGS
0
Figure 19. Switching Time Test Circuit
FDD8882/FDU8882 Rev. C
50%
10%
50%
PULSE WIDTH
Figure 20. Switching Time Waveforms
7
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
Test Circuits and Waveforms
The maximum rated junction temperature, TJM, and the
thermal resistance of the heat dissipating path determines
the maximum allowable device power dissipation, PDM, in an
application.
Therefore the application’s ambient
temperature, TA (oC), and thermal resistance RθJA (oC/W)
must be reviewed to ensure that TJM is never exceeded.
Equation 1 mathematically represents the relationship and
serves as the basis for establishing the rating of the part.
RθJA = 33.32+ 23.84/(0.268+Area) EQ.2
RθJA = 33.32+ 154/(1.73+Area) EQ.3
100
RθJA (oC/W)
( T JM – TA )
P DM = ----------------------------Rθ JA
125
(EQ. 1)
75
50
In using surface mount devices such as the TO-252
package, the environment in which it is applied will have a
significant influence on the part’s current and maximum
power dissipation ratings. Precise determination of PDM is
complex and influenced by many factors:
25
0.01
(0.0645)
0.1
(0.645)
1
10
(6.45)
(64.5)
AREA, TOP COPPER AREA in2 (cm2)
Figure 21. Thermal Resistance vs Mounting
Pad Area
1. Mounting pad area onto which the device is attached and
whether there is copper on one side or both sides of the
board.
2. The number of copper layers and the thickness of the
board.
3. The use of external heat sinks.
4. The use of thermal vias.
5. Air flow and board orientation.
6. For non steady state applications, the pulse width, the
duty cycle and the transient thermal response of the part,
the board and the environment they are in.
Fairchild provides thermal information to assist the
designer’s preliminary application evaluation. Figure 21
defines the RθJA for the device as a function of the top
copper (component side) area. This is for a horizontally
positioned FR-4 board with 1oz copper after 1000 seconds
of steady state power with no air flow. This graph provides
the necessary information for calculation of the steady state
junction temperature or power dissipation. Pulse
applications can be evaluated using the Fairchild device
Spice thermal model or manually utilizing the normalized
maximum transient thermal impedance curve.
Thermal resistances corresponding to other copper areas
can be obtained from Figure 21 or by calculation using
Equation 2 or 3. Equation 2 is used for copper area defined
in inches square and equation 3 is for area in centimeters
square. The area, in square inches or square centimeters is
the top copper area including the gate and source pads.
23.84
( 0.268 + Area )
R θJA = 33.32 + -------------------------------------
(EQ. 2)
Area in Inches Squared
154
( 1.73 + Area )
R θ JA = 33.32 + ----------------------------------
(EQ. 3)
Area in Centimeters Squared
FDD8882/FDU8882 Rev. C
8
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
Thermal Resistance vs. Mounting Pad Area
.SUBCKT FDD8882 2 1 3 ; rev October 2004
Ca 12 8 9e-10
Cb 15 14 9e-10
Cin 6 8 1.55e-9
LDRAIN
DPLCAP
DRAIN
2
5
10
Dbody 7 5 DbodyMOD
Dbreak 5 11 DbreakMOD
Dplcap 10 5 DplcapMOD
5
51
ESLC
EVTHRES
+ 19 8
+
LGATE
GATE
1
11
+
17
EBREAK 18
-
50
RDRAIN
6
8
ESG
DBREAK
+
RSLC2
Ebreak 11 7 17 18 34.1
Eds 14 8 5 8 1
Egs 13 8 6 8 1
Esg 6 10 6 8 1
Evthres 6 21 19 8 1
Evtemp 20 6 18 22 1
It 8 17 1
RLDRAIN
RSLC1
51
EVTEMP
RGATE + 18 22
9
20
21
16
DBODY
MWEAK
6
MMED
MSTRO
RLGATE
Lgate 1 9 8.6e-9
Ldrain 2 5 1.0e-9
Lsource 3 7 2.67e-9
LSOURCE
CIN
8
7
SOURCE
3
RSOURCE
RLSOURCE
RLgate 1 9 86
RLdrain 2 5 10
RLsource 3 7 26.7
Mmed 16 6 8 8 MmedMOD
Mstro 16 6 8 8 MstroMOD
Mweak 16 21 8 8 MweakMOD
S1A
12
S2A
13
8
15
14
13
S1B
CA
RBREAK
17
18
RVTEMP
S2B
13
CB
6
8
EGS
Rbreak 17 18 RbreakMOD 1
Rdrain 50 16 RdrainMOD 2.5e-3
Rgate 9 20 2.43
RSLC1 5 51 RSLCMOD 1e-6
RSLC2 5 50 1e3
Rsource 8 7 RsourceMOD 6.5e-3
Rvthres 22 8 RvthresMOD 1
Rvtemp 18 19 RvtempMOD 1
S1a 6 12 13 8 S1AMOD
S1b 13 12 13 8 S1BMOD
S2a 6 15 14 13 S2AMOD
S2b 13 15 14 13 S2BMOD
19
VBAT
5
8
EDS
-
IT
14
+
+
-
+
8
22
RVTHRES
Vbat 22 19 DC 1
ESLC 51 50 VALUE={(V(5,51)/ABS(V(5,51)))*(PWR(V(5,51)/(1e-6*600),10))}
.MODEL DbodyMOD D (IS=2E-12 IKF=10 N=1.01 RS=5.7e-3 TRS1=8e-4 TRS2=2e-7
+ CJO=4.6e-10 M=0.58 TT=1e-11 XTI=2.7)
.MODEL DbreakMOD D (RS=1 TRS1=1e-3 TRS2=-8.9e-6)
.MODEL DplcapMOD D (CJO=5.0e-10 IS=1e-30 N=10 M=0.45)
.MODEL MmedMOD NMOS (VTO=2.11 KP=14 IS=1e-30 N=10 TOX=1 L=1u W=1u RG=2.43)
.MODEL MstroMOD NMOS (VTO=2.65 KP=240 IS=1e-30 N=10 TOX=1 L=1u W=1u)
.MODEL MweakMOD NMOS (VTO=1.82 KP=0.09 IS=1e-30 N=10 TOX=1 L=1u W=1u RG=24.3 RS=0.1)
.MODEL RbreakMOD RES (TC1=8.0e-4 TC2=-8e-7)
.MODEL RdrainMOD RES (TC1=-6e-3 TC2=6e-6)
.MODEL RSLCMOD RES (TC1=8e-5 TC2=2e-6)
.MODEL RsourceMOD RES (TC1=7.5e-3 TC2=1e-6)
.MODEL RvthresMOD RES (TC1=-1.2e-3 TC2=-8.3e-6)
.MODEL RvtempMOD RES (TC1=-2.5e-3 TC2=3.3e-7)
.MODEL S1AMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=-4 VOFF=-3.5)
.MODEL S1BMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=-3.5 VOFF=-4)
.MODEL S2AMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=-2 VOFF=-1.5)
.MODEL S2BMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=-1.5 VOFF=-2)
.ENDS
Note: For further discussion of the PSPICE model, consult A New PSPICE Sub-Circuit for the Power MOSFET Featuring Global
Temperature Options; IEEE Power Electronics Specialist Conference Records, 1991, written by William J. Hepp and C. Frank
Wheatley.
FDD8882/FDU8882 Rev. C
9
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
PSPICE Electrical Model
rev October 2004
template FDD8882 n2,n1,n3
electrical n2,n1,n3
{
var i iscl
dp..model dbodymod = (isl=2.0e-12,ikf=10,nl=1.01,rs=5.7e-3,trs1=8e-4,trs2=2e-7,cjo=4.6e-10,m=0.58,tt=1e-11,xti=2.7)
dp..model dbreakmod = (rs=1,trs1=1e-3,trs2=-8.9e-6)
dp..model dplcapmod = (cjo=5.0e-10,isl=10e-30,nl=10,m=0.45)
m..model mmedmod = (type=_n,vto=2.11,kp=14,is=1e-30, tox=1)
m..model mstrongmod = (type=_n,vto=2.65,kp=240,is=1e-30, tox=1)
m..model mweakmod = (type=_n,vto=1.82,kp=0.09,is=1e-30, tox=1,rs=0.1)
sw_vcsp..model s1amod = (ron=1e-5,roff=0.1,von=-4,voff=-3.5)
LDRAIN
sw_vcsp..model s1bmod = (ron=1e-5,roff=0.1,von=-3.5,voff=-4)
DPLCAP 5
sw_vcsp..model s2amod = (ron=1e-5,roff=0.1,von=-2,voff=-1.5)
10
sw_vcsp..model s2bmod = (ron=1e-5,roff=0.1,von=-1.5,voff=-2)
RLDRAIN
RSLC1
c.ca n12 n8 = 9e-10
51
c.cb n15 n14 = 9e-10
RSLC2
c.cin n6 n8 = 1.1e-9
DRAIN
2
ISCL
dp.dbody n7 n5 = model=dbodymod
dp.dbreak n5 n11 = model=dbreakmod
dp.dplcap n10 n5 = model=dplcapmod
-
RDRAIN
6
8
ESG
EVTHRES
+ 19 8
+
spe.ebreak n11 n7 n17 n18 = 34.1
spe.eds n14 n8 n5 n8 = 1
GATE
spe.egs n13 n8 n6 n8 = 1
1
spe.esg n6 n10 n6 n8 = 1
spe.evthres n6 n21 n19 n8 = 1
spe.evtemp n20 n6 n18 n22 = 1
LGATE
EVTEMP
RGATE +
18 22
9
20
21
11
DBODY
16
MWEAK
6
EBREAK
+
17
18
-
MMED
MSTRO
RLGATE
CIN
8
LSOURCE
7
SOURCE
3
RSOURCE
i.it n8 n17 = 1
RLSOURCE
S1A
l.lgate n1 n9 = 8.6e-9
l.ldrain n2 n5 = 1.0e-9
l.lsource n3 n7 = 2.67e-9
res.rlgate n1 n9 = 86
res.rldrain n2 n5 = 10
res.rlsource n3 n7 = 26.7
DBREAK
50
12
S2A
14
13
13
8
S1B
15
17
18
RVTEMP
S2B
13
CA
RBREAK
CB
6
8
EGS
-
19
IT
14
+
+
VBAT
5
8
EDS
-
m.mmed n16 n6 n8 n8 = model=mmedmod, l=1u, w=1u
m.mstrong n16 n6 n8 n8 = model=mstrongmod, l=1u, w=1u
m.mweak n16 n21 n8 n8 = model=mweakmod, l=1u, w=1u
+
8
22
RVTHRES
res.rbreak n17 n18 = 1, tc1=8.0e-4,tc2=-8e-7
res.rdrain n50 n16 = 2.5e-3, tc1=-6e-3,tc2=6e-6
res.rgate n9 n20 = 2.43
res.rslc1 n5 n51 = 1e-6, tc1=8e-5,tc2=2e-6
res.rslc2 n5 n50 = 1e3
res.rsource n8 n7 = 6.5e-3, tc1=7.5e-3,tc2=1e-6
res.rvthres n22 n8 = 1, tc1=-1.2e-3,tc2=-8.3e-6
res.rvtemp n18 n19 = 1, tc1=-2.5e-3,tc2=3.3e-7
sw_vcsp.s1a n6 n12 n13 n8 = model=s1amod
sw_vcsp.s1b n13 n12 n13 n8 = model=s1bmod
sw_vcsp.s2a n6 n15 n14 n13 = model=s2amod
sw_vcsp.s2b n13 n15 n14 n13 = model=s2bmod
v.vbat n22 n19 = dc=1
equations {
i (n51->n50) +=iscl
iscl: v(n51,n50) = ((v(n5,n51)/(1e-9+abs(v(n5,n51))))*((abs(v(n5,n51)*1e6/600))** 10))
}
}
FDD8882/FDU8882 Rev. C
10
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
SABER Electrical Model
th
JUNCTION
REV 23 October 2004
FDD8882T
CTHERM1 TH 6 5.6e-4
CTHERM2 6 5 6.8e-4
CTHERM3 5 4 2.0e-3
CTHERM4 4 3 2.8e-3
CTHERM5 3 2 5.7e-3
CTHERM6 2 TL 5.8e-3
RTHERM1
CTHERM1
6
RTHERM1 TH 6 5.3e-2
RTHERM2 6 5 2.2e-1
RTHERM3 5 4 2.9e-1
RTHERM4 4 3 3.9e-1
RTHERM5 3 2 6.0e-1
RTHERM6 2 TL 6.6e-1
RTHERM2
CTHERM2
5
SABER Thermal Model
SABER thermal model FDD8882T
template thermal_model th tl
thermal_c th, tl
{
ctherm.ctherm1 th 6 =5.6e-4
ctherm.ctherm2 6 5 =6.8e-4
ctherm.ctherm3 5 4 =2.0e-3
ctherm.ctherm4 4 3 =2.8e-3
ctherm.ctherm5 3 2 =5.7e-3
ctherm.ctherm6 2 tl =5.8e-3
RTHERM3
CTHERM3
4
RTHERM4
rtherm.rtherm1 th 6 =5.3e-2
rtherm.rtherm2 6 5 =2.2e-1
rtherm.rtherm3 5 4 =2.9e-1
rtherm.rtherm4 4 3 =3.9e-1
rtherm.rtherm5 3 2 =6.0e-1
rtherm.rtherm6 2 tl =6.6e-1
}
CTHERM4
3
RTHERM5
CTHERM5
2
CTHERM6
RTHERM6
tl
FDD8882/FDU8882 Rev. C
11
CASE
www.fairchildsemi.com
FDD8882 / FDU8882 N-Channel PowerTrench® MOSFET
PSPICE Thermal Model
TRADEMARKS
The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global
subsidianries, and is not intended to be an exhaustive list of all such trademarks.
ACEx®
Build it Now™
CorePLUS™
CorePOWER™
CROSSVOLT™
CTL™
Current Transfer Logic™
EcoSPARK®
EfficentMax™
EZSWITCH™ *
FPS™
F-PFS™
FRFET®
Global Power ResourceSM
Green FPS™
Green FPS™ e-Series™
GTO™
IntelliMAX™
ISOPLANAR™
MegaBuck™
MICROCOUPLER™
MicroFET™
MicroPak™
MillerDrive™
MotionMax™
Motion-SPM™
OPTOLOGIC®
OPTOPLANAR®
™
®
Fairchild®
Fairchild Semiconductor®
FACT Quiet Series™
FACT®
FAST®
FastvCore™
FlashWriter® *
®
PDP-SPM™
Power-SPM™
PowerTrench®
Programmable Active Droop™
QFET®
QS™
Quiet Series™
RapidConfigure™
Saving our world 1mW at a time™
SmartMax™
SMART START™
SPM®
STEALTH™
SuperFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SuperMOS™
®
The Power Franchise®
tm
TinyBoost™
TinyBuck™
TinyLogic®
TINYOPTO™
TinyPower™
TinyPWM™
TinyWire™
µSerDes™
UHC®
Ultra FRFET™
UniFET™
VCX™
VisualMax™
tm
* EZSWITCH™ and FlashWriter® are trademarks of System General Corporation, used under license by Fairchild Semiconductor.
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS
HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE
APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER
ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S
WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1.
Life support devices or systems are devices or systems which,
(a) are intended for surgical implant into the body or (b)
support or sustain life, and (c) whose failure to perform when
properly used in accordance with instructions for use provided
in the labeling, can be reasonably expected to result in a
significant injury of the user.
2.
A critical component in any component of a life support,
device, or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or In Design
This datasheet contains the design specifications for product development.
Specifications may change in any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make
changes at any time without notice to improve design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild Semiconductor reserves
the right to make changes at any time without notice to improve the design.
Obsolete
Not In Production
This datasheet contains specifications on a product that is discontinued by
Fairchild Semiconductor. The datasheet is for reference information only.
Rev. I34
FDD8882/FDU8882 Rev. C
www.fairchildsemi.com