TI LM301AD

LM101A, LM201A, LM301A
HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
D961, OCTOBER 1979 – REVISED SEPTEMBER 1990
•
•
•
•
•
•
D, JG, OR P PACKAGE
(T0P VIEW)
Low Input Currents
Low Input Offset Parameters
N1/COMP
IN –
IN +
VCC–
Frequency and Transient Response
Characteristics Adjustable
Short-Circuit Protection
1
8
2
7
3
6
4
5
COMP
VCC+
OUT
OFFSET N2
Offset-Voltage Null Capability
LM101A
W FLAT PACKAGE
(T0P VIEW)
No Latch-Up
Wide Common-Mode and Differential
Voltage Ranges
Same Pin Assignments as uA709
Designed to be Interchangeable with
National Semiconductor LM101A and
LM301A
description
The LM101A, LM201A, and LM301A are highperformance operational amplifiers featuring very
low input bias current and input offset voltage and
current to improve the accuracy of highimpedance circuits using these devices. The high
common-mode input voltage range and the
absence of latch-up make these amplifiers ideal
for voltage-follower applications. The devices are
protected to withstand short circuits at the output.
The external compensation of these amplifiers
allows the changing of the frequency response
(when the closed-loop gain is greater then unity)
for applications requiring wider bandwidth or
higher slew rate. A potentiometer may be
connected between the offset-null inputs (N1 and
N2), as shown in Figure 7, to null out the offset
voltage.
The LM101A is characterized for operation over
the full military temperature range of – 55°C to
125°C, the LM201A is characterized for operation
from – 25°C to 85°C, and the LM301A is
characterized for operation from 0°C to 70°C.
symbol
Inverting
Input IN–
+
1
14
2
13
3
12
4
11
5
10
6
9
7
8
NC
NC
COMP
VCC+
OUT
OFFSET N2
NC
LM101A
U FLAT PACKAGE
(T0P VIEW)
NC
N1/COMP
IN –
IN +
VCC –
1
NC
COMP
VCC+
OUT
OFFSET N2
10
2
9
3
8
4
7
5
6
LM101A
FK CHIP-CARRIER PACKAGE
(T0P VIEW)
NC
IN –
NC
IN +
NC
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
NC
VCC+
NC
OUT
NC
Output
–
NC
VCC –
NC
N2
NC
Noninverting
Input IN+
NC
NC
N1/COMP
IN –
IN +
VCC –
NC
NC
N1/COMP
NC
COMP
NC
•
•
•
N2
N1/
COMP
NC – No internal connection
Copyright  1991, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2–1
LM101A, LM201A, LM301A
HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
AVAILABLE OPTIONS
PACKAGE
VIO MAX
at 25°C
TA
0°C to 70°C
SMALL OUTLINE
CHIP CARRIER
CERAMIC DIP
PLASTIC DIP
FLAT
PACK
FLAT PACK
(D)
(FK)
(JG)
(P)
(U)
(W)
–
7.5 mV
LM301AD
–
–
LM301AP
–
– 25 °C to 85°C
2 mV
LM201AD
–
–
LM201AP
–
–
– 55 °C to 125°C
2 mV
LM101AD
LM101AFK
LM101AJG
LM101AP
LM101AU
LM101AW
The D package is available taped and reeled. Add the suffix R to the device type, (i.e., LM301ADR).
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
LM101A
LM201A
LM301A
UNIT
Supply voltage VCC+ (see Note 1)
22
22
18
V
Supply voltage VCC– (see Note 1)
– 22
– 22
– 18
V
Differential input voltage (see Note 2)
±30
±30
±30
V
Input voltage (either input, see Notes 1 and 3)
±15
±15
±15
V
Voltage between either offset null terminal (N1/N2) and VCC–
– 0.5 to 2
– 0.5 to 2
– 0.5 to 2
V
Duration of output short-circuit (see Note 4)
unlimited
unlimited
unlimited
Continuous total power dissipation
See Dissipation Rating Table
Operating free-air temperature range
– 55 to 125
– 25 to 85
0 to 70
°C
Storage temperature range
– 65 to 150
– 65 to 150
– 65 to 150
°C
Case temperature for 60 seconds: FK package
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds
JG, U, or W package
300
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
D or P package
260
NOTES: 1.
2.
3.
4.
°C
260
°C
260
°C
260
All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC–.
Differential voltages are at the noninverting input terminal with respect to the inverting input terminal.
The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.
The output may be shorted to ground or either power supply. For the LM101A only, the unlimited duration of the short-circuit applies
at (or above) 125°C case temperature or 75°C free-air temperature. For the LM201A only, the unlimited duration of the short-circuit
applies at (or below) 85°C case temperatuare or 75°C free-air temperature.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING
DERATE
FACTOR
ABOVE TA
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
D
500 mW
5.8 mW/°C
64°C
464 mW
377 mW
145 mW
FK
500 mW
11.0 mW/°C
105°C
500 mW
500 mW
275 mW
JG
500 mW
8.4 mW/°C
90°C
500 mW
500 mW
210 mW
P
500 mW
8.0 mW/°C
87°C
500 mW
500 mW
200 mW
U
500 mW
5.4 mW/°C
57°C
432 mW
351 mW
135 mW
W
500 mW
8.0 mW/°C
87°C
500 mW
500 mW
200 mW
recommended operating conditions
MIN
MAX
Supply voltage, VCC+
5
18
Supply voltage, VCC–
–5
– 18
2–2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
V
LM101A, LM201A, LM301A
HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
electrical characteristics at specified free-air temperature, CC = 30 pF (see Note 5)
PARAMETER
TEST CONDITIONS†
VIO
Input offset voltage
VO = 0
αVIO
Average temperature coefficient of
input offset voltage
VO = 0
IIO
Input offset current
αIIO
Average temperature coefficient of
input offset current
LM101A, LM201A
MIN
25°C
LM301A
TYP
MAX
0.6
2
Full range
MIN
3
15
6
30
25°C
1.5
10
3
50
20
0.02
0.2
0.01
0.1
70
0.02
25°C
Common-mode input voltage range
See Note 6
Maximum peak-to-peak output
VCC± = ±15 V,
RL = 10 kΩ
VOPP
voltage swing
AVD
Large-signal differential voltage
amplification
ri
Input resistance
CMRR
kSVR
ICC
Common-mode rejection ratio
VCC± = ±15 V,
VO = ±10 V,
RL ≥ 2 kΩ
VIC = VICR min
(∆ VCC/∆ VIO)
75
0.6
0.01
0.3
70
250
100
300
Full range
±15
25°C
24
Full range
24
25°C
20
Full range
20
25°C
50
Full range
25
25°C
1.5
4
0.5
2
25°C
80
98
70
90
Full range
80
25°C
80
Full range
80
Supply voltage rejection ratio
Supply current
30
Full range
VCC± = ±15 V,
RL = 2 kΩ
7.5
10
TA = 25°C to 70°C
VICR
2
Full range
TA = – 55°C to 25°C
TA = 25°C to MAX
TA = 0°C to 25°C
Input bias current
MAX
3
Full range
IIB
TYP
±12
28
24
20
mV
µV/°C
nA
nA/°C
nA
V
28
24
26
UNIT
V
26
20
200
25
200
V/mV
15
MΩ
dB
70
98
70
96
dB
70
No load, VO = 0,
25°C
1.8
3
See Note 6
MAX
1.2
2.5
1.8
3
mA
† All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. Full range for
LM101A is – 55°C to 125°C, for LM201A is – 25°C to 85°C, and for LM301A is 0°C to 70°C.
NOTES: 5. Unless otherwise noted, VCC± = ± 5 V to ± 20 V for LM101A and LM201A, and VCC± = ± 5 V to ± 15 V for LM301A. All typical values
are at VCC± = ±15 V.
6. For LM101A and LM201A, VCC± = ± 20 V. For LM301A, VCC± = ± 15 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2–3
LM101A, LM201A, LM301A
HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
TYPICAL CHARACTERISTICS
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
100
4
VCC ± = ±15 V
3
I IB – Input Bias Current – nA
I IO – Input Offset Current – nA
VCC ± = ±15 V
LM301A
2I
1
LM101A
LM201A
–50
LM301A
60
40
LM101A
LM201A
20
0
–75
0
–7
80
–25
0
25
50
75 100
TA – Free-Air Temperature – °C
125
–50
–25
0
25
50
75
100
TA – Free-Air Temperature – °C
30
Figure 2
OPEN-LOOP LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
SUPPLY VOLTAGE
MAXIMUM PEAK-TO-PEAK OUTPUT
VOLTAGE
(WITH SINGLE-POLE COMPENSATION)
vs
FREQUENCY
400
VCC ± = ±15 V
RL = 10 KΩ
TA = 25°C
28
A VD – Differential Voltage Amplification – V/mV
VOPP – Maximum Peak-to-Peak Output Voltage – V
Figure 1
24
20
16
12
CC = 3 pF
8
CC = 30 pF
4
0
1k
10 k
100 k
1M
10 M
RL = 2 KΩ
TA = 25°C
200
100
40
LM301A
LM101A
20
10
LM201A
0
2
f – Frequency – Hz
Figure 3
2–4
125
4
6
8 10 12 14 16
| VCC± | – Supply Voltage – V
Figure 4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
18 20
LM101A, LM201A, LM301A
HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
TYPICAL CHARACTERISTICS
OPEN-LOOP LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREQUENCY
VOLTAGE-FOLLOWER
LARGE-SIGNAL PULSE RESPONSE
8
VCC ± = ±15 V
RL = 2 kΩ
CC = 30 pF
TA = 25°C
106
105
104
103
102
101
1
10–1
VCC ± = ±15 V
RL = 2 kΩ
CL = 100 pF
CC = 30 pF
TA = 25°C
6
Input and Output Voltages – V
A VD – Differential Voltage Amplification
107
4
2
Output
0
–2
Input
–4
–6
–8
1
10
100
1k
10 k 100 k 1 M
10 M 100 M
0
10
f – Frequency – Hz
Figure 5
20
30 40 50
t – Time – µs
60
70
80
90
Figure 6
TYPICAL APPLICATION DATA
R2
VCC+
VO
VI
–
CC
R1
VI
R3
R3
+
VO
VCC–
N1
COMP
RL ≥ 2 kΩ
+ * R2
R1
w [email protected])30R2pF
+ R1R1 )@ R2R2
N2
5 MΩ
CC
5.1 MΩ
Figure 7. Inverting Circuit with Adjustable Gain, Single-Pole Compensation,
and Offset Adjustment
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2–5
LM101A, LM201A, LM301A
HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
2–6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor
product or service without notice, and advises its customers to obtain the latest version of relevant information
to verify, before placing orders, that the information being relied on is current.
TI warrants performance of its semiconductor products and related software to the specifications applicable at
the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are
utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each
device is not necessarily performed, except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or
severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED
TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI
products in such applications requires the written approval of an appropriate TI officer. Questions concerning
potential risk applications should be directed to TI through a local SC sales office.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards should be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein. Nor does TI warrant or represent that any license, either
express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property
right of TI covering or relating to any combination, machine, or process in which such semiconductor products
or services might be or are used.
Copyright  1996, Texas Instruments Incorporated