SST SST39LF020-45-4I-NHE

512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit (x8) Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
SST39LF/VF512 / 010 / 020 / 0403.0 & 2.7V 512Kb / 1Mb / 2Mb / 4Mb (x8) MPF memories
Data Sheet
FEATURES:
• Organized as 64K x8 / 128K x8 / 256K x8 / 512K x8
• Single Voltage Read and Write Operations
– 3.0-3.6V for SST39LF512/010/020/040
– 2.7-3.6V for SST39VF512/010/020/040
• Superior Reliability
– Endurance: 100,000 Cycles (typical)
– Greater than 100 years Data Retention
• Low Power Consumption
(typical values at 14 MHz)
– Active Current: 5 mA (typical)
– Standby Current: 1 µA (typical)
• Sector-Erase Capability
– Uniform 4 KByte sectors
• Fast Read Access Time:
– 45 ns for SST39LF512/010/020/040
– 55 ns for SST39LF020/040
– 70 ns for SST39VF512/010/020/040
• Latched Address and Data
• Fast Erase and Byte-Program:
– Sector-Erase Time: 18 ms (typical)
– Chip-Erase Time: 70 ms (typical)
– Byte-Program Time: 14 µs (typical)
– Chip Rewrite Time:
1 second (typical) for SST39LF/VF512
2 seconds (typical) for SST39LF/VF010
4 seconds (typical) for SST39LF/VF020
8 seconds (typical) for SST39LF/VF040
• Automatic Write Timing
– Internal VPP Generation
• End-of-Write Detection
– Toggle Bit
– Data# Polling
• CMOS I/O Compatibility
• JEDEC Standard
– Flash EEPROM Pinouts and command sets
• Packages Available
– 32-lead PLCC
– 32-lead TSOP (8mm x 14mm)
– 48-ball TFBGA (6mm x 8mm)
– 34-ball WFBGA (4mm x 6mm) for 1M and 2M
• All devices are RoHS compliant
PRODUCT DESCRIPTION
The SST39LF512, SST39LF010, SST39LF020, SST39LF040
and SST39VF512, SST39VF010, SST39VF020, SST39VF040
are 64K x8, 128K x8, 256K x8 and 5124K x8 CMOS Multi-Purpose Flash (MPF) manufactured with SST’s proprietary, high performance CMOS SuperFlash technology. The split-gate cell
design and thick-oxide tunneling injector attain better reliability and
manufacturability compared with alternate approaches. The
SST39LF512/010/020/040 devices write (Program or Erase) with
a 3.0-3.6V power supply. The SST39VF512/010/020/040 devices
write with a 2.7-3.6V power supply. The devices conform to
JEDEC standard pinouts for x8 memories.
Featuring high performance Byte-Program, the
SST39LF512/010/020/040 and SST39VF512/010/020/
040 devices provide a maximum Byte-Program time of 20
µsec. These devices use Toggle Bit or Data# Polling to indicate the completion of Program operation. To protect
against inadvertent write, they have on-chip hardware and
Software Data Protection schemes. Designed, manufactured, and tested for a wide spectrum of applications, they
are offered with a guaranteed typical endurance of
100,000 cycles. Data retention is rated at greater than 100
years.
The SST39LF512/010/020/040 and SST39VF512/010/
020/040 devices are suited for applications that require
convenient and economical updating of program, configu©2010 Silicon Storage Technology, Inc.
S71150-14-000
01/10
1
ration, or data memory. For all system applications, they
significantly improves performance and reliability, while lowering power consumption. They inherently use less energy
during Erase and Program than alternative flash technologies. The total energy consumed is a function of the
applied voltage, current, and time of application. Since for
any given voltage range, the SuperFlash technology uses
less current to program and has a shorter erase time, the
total energy consumed during any Erase or Program operation is less than alternative flash technologies. These
devices also improve flexibility while lowering the cost for
program, data, and configuration storage applications.
The SuperFlash technology provides fixed Erase and Program times, independent of the number of Erase/Program
cycles that have occurred. Therefore the system software
or hardware does not have to be modified or de-rated as is
necessary with alternative flash technologies, whose Erase
and Program times increase with accumulated Erase/Program cycles.
To meet surface mount requirements, the SST39LF512/
010/020/040 and SST39VF512/010/020/040 devices are
offered in 32-lead PLCC and 32-lead TSOP packages. The
SST39LF/VF010 and SST39LF/VF020 are also offered in
a 48-ball TFBGA package. See Figures 2, 3, 4, and 5 for
pin assignments.
The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc.
MPF is a trademark of Silicon Storage Technology, Inc.
These specifications are subject to change without notice.
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
Device Operation
edge of the sixth WE# pulse. The internal Erase operation
begins after the sixth WE# pulse. The End-of-Erase can be
determined using either Data# Polling or Toggle Bit methods. See Figure 11 for timing waveforms. Any commands
written during the Sector-Erase operation will be ignored.
Commands are used to initiate the memory operation functions of the device. Commands are written to the device
using standard microprocessor write sequences. A command is written by asserting WE# low while keeping CE#
low. The address bus is latched on the falling edge of WE#
or CE#, whichever occurs last. The data bus is latched on
the rising edge of WE# or CE#, whichever occurs first.
Chip-Erase Operation
The SST39LF512/010/020/040 and SST39VF512/010/
020/040 devices provide a Chip-Erase operation, which
allows the user to erase the entire memory array to the ‘1’s
state. This is useful when the entire device must be quickly
erased.
Read
The Read operation of the SST39LF512/010/020/040 and
SST39VF512/010/020/040 device is controlled by CE#
and OE#, both have to be low for the system to obtain data
from the outputs. CE# is used for device selection. When
CE# is high, the chip is deselected and only standby power
is consumed. OE# is the output control and is used to gate
data from the output pins. The data bus is in high impedance state when either CE# or OE# is high. Refer to the
Read cycle timing diagram for further details (Figure 6).
The Chip-Erase operation is initiated by executing a sixbyte Software Data Protection command sequence with
Chip-Erase command (10H) with address 5555H in the last
byte sequence. The internal Erase operation begins with
the rising edge of the sixth WE# or CE#, whichever occurs
first. During the internal Erase operation, the only valid read
is Toggle Bit or Data# Polling. See Table 4 for the command
sequence, Figure 12 for timing diagram, and Figure 20 for
the flowchart. Any commands written during the ChipErase operation will be ignored.
Byte-Program Operation
The SST39LF512/010/020/040 and SST39VF512/010/
020/040 are programmed on a byte-by-byte basis. Before
programming, the sector where the byte exists must be
fully erased. The Program operation is accomplished in
three steps. The first step is the three-byte load sequence
for Software Data Protection. The second step is to load
byte address and byte data. During the Byte-Program
operation, the addresses are latched on the falling edge of
either CE# or WE#, whichever occurs last. The data is
latched on the rising edge of either CE# or WE#, whichever
occurs first. The third step is the internal Program operation
which is initiated after the rising edge of the fourth WE# or
CE#, whichever occurs first. The Program operation, once
initiated, will be completed, within 20 µs. See Figures 7 and
8 for WE# and CE# controlled Program operation timing
diagrams and Figure 17 for flowcharts. During the Program
operation, the only valid reads are Data# Polling and Toggle Bit. During the internal Program operation, the host is
free to perform additional tasks. Any commands written
during the internal Program operation will be ignored.
Write Operation Status Detection
The SST39LF512/010/020/040 and SST39VF512/010/
020/040 devices provide two software means to detect the
completion of a Write (Program or Erase) cycle, in order to
optimize the system write cycle time. The software detection includes two status bits: Data# Polling (DQ7) and Toggle Bit (DQ6). The End-of-Write detection mode is enabled
after the rising edge of WE# which initiates the internal Program or Erase operation.
The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a Data# Polling or
Toggle Bit read may be simultaneous with the completion
of the Write cycle. If this occurs, the system may possibly
get an erroneous result, i.e., valid data may appear to conflict with either DQ7 or DQ6. In order to prevent spurious
rejection, if an erroneous result occurs, the software routine
should include a loop to read the accessed location an
additional two (2) times. If both reads are valid, then the
device has completed the Write cycle, otherwise the rejection is valid.
Sector-Erase Operation
The Sector-Erase operation allows the system to erase the
device on a sector-by-sector basis. The sector architecture
is based on uniform sector size of 4 KByte. The SectorErase operation is initiated by executing a six-byte command sequence with Sector-Erase command (30H) and
sector address (SA) in the last bus cycle. The sector
address is latched on the falling edge of the sixth WE#
pulse, while the command (30H) is latched on the rising
©2010 Silicon Storage Technology, Inc.
S71150-14-000
2
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
Data# Polling (DQ7)
Software Data Protection (SDP)
When the SST39LF512/010/020/040 and SST39VF512/
010/020/040 are in the internal Program operation, any
attempt to read DQ7 will produce the complement of the
true data. Once the Program operation is completed, DQ7
will produce true data. Note that even though DQ7 may
have valid data immediately following completion of an
internal Write operation, the remaining data outputs may
still be invalid: valid data on the entire data bus will appear
in subsequent successive Read cycles after an interval of 1
µs. During internal Erase operation, any attempt to read
DQ7 will produce a “0”. Once the internal Erase operation is
completed, DQ7 will produce a “1”. The Data# Polling is
valid after the rising edge of fourth WE# (or CE#) pulse for
Program operation. For Sector- or Chip-Erase, the Data#
Polling is valid after the rising edge of sixth WE# (or CE#)
pulse. See Figure 9 for Data# Polling timing diagram and
Figure 18 for a flowchart.
The SST39LF512/010/020/040 and SST39VF512/010/
020/040 provide the JEDEC approved Software Data Protection scheme for all data alteration operation, i.e., Program and Erase. Any Program operation requires the
inclusion of a series of three-byte sequence. The three-byte
load sequence is used to initiate the Program operation,
providing optimal protection from inadvertent Write operations, e.g., during the system power-up or power-down.
Any Erase operation requires the inclusion of six-byte load
sequence. These devices are shipped with the Software
Data Protection permanently enabled. See Table 4 for the
specific software command codes. During SDP command
sequence, invalid commands will abort the device to read
mode, within TRC.
Product Identification
The Product Identification mode identifies the devices as
the SST39LF/VF512, SST39LF/VF010, SST39LF/VF020
and SST39LF/VF040 and manufacturer as SST. This
mode may be accessed by software operations. Users
may use the Software Product Identification operation to
identify the part (i.e., using the device ID) when using multiple manufacturers in the same socket. For details, see
Table 4 for software operation, Figure 13 for the Software
ID Entry and Read timing diagram, and Figure 19 for the
Software ID entry command sequence flowchart.
Toggle Bit (DQ6)
During the internal Program or Erase operation, any consecutive attempts to read DQ6 will produce alternating ‘0’s
and ‘1’s, i.e., toggling between 0 and 1. When the internal
Program or Erase operation is completed, the toggling will
stop. The device is then ready for the next operation. The
Toggle Bit is valid after the rising edge of fourth WE# (or
CE#) pulse for Program operation. For Sector- or ChipErase, the Toggle Bit is valid after the rising edge of sixth
WE# (or CE#) pulse. See Figure 10 for Toggle Bit timing
diagram and Figure 18 for a flowchart.
TABLE 1: Product Identification
Address
Data
0000H
BFH
SST39LF/VF512
0001H
D4H
SST39LF/VF010
0001H
D5H
SST39LF/VF020
0001H
D6H
SST39LF/VF040
0001H
D7H
Manufacturer’s ID
Data Protection
Device ID
The SST39LF512/010/020/040 and SST39VF512/010/
020/040 provide both hardware and software features to
protect nonvolatile data from inadvertent writes.
Hardware Data Protection
T1.1 1150
Noise/Glitch Protection: A WE# or CE# pulse of less than 5
ns will not initiate a Write cycle.
Product Identification Mode Exit/Reset
VDD Power Up/Down Detection: The Write operation is
inhibited when VDD is less than 1.5V.
In order to return to the standard Read mode, the Software
Product Identification mode must be exited. Exit is accomplished by issuing the Software ID Exit command
sequence, which returns the device to the Read operation.
Please note that the Software ID Exit command is ignored
during an internal Program or Erase operation. See Table 4
for software command codes, Figure 14 for timing waveform, and Figure 19 for a flowchart.
Write Inhibit Mode: Forcing OE# low, CE# high, or WE#
high will inhibit the Write operation. This prevents inadvertent writes during power-up or power-down.
©2010 Silicon Storage Technology, Inc.
S71150-14-000
3
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
SuperFlash
Memory
X-Decoder
Memory Address
Address Buffers & Latches
Y-Decoder
CE#
I/O Buffers and Data Latches
Control Logic
OE#
WE#
DQ7 - DQ0
1150 B1.1
A17
WE#
NC
NC
A17
WE#
WE#
WE#
VDD
A18
VDD
VDD
A16
VDD
NC
NC
4
3
2
1
32 31 30
29
NC
A16
NC
A16
A12
A15
A15
A15
A12
A12
A15
SST39LF/VF040 SST39LF/VF020 SST39LF/VF010 SST39LF/VF512
A12
SST39LF/VF512 SST39LF/VF010 SST39LF/VF020 SST39LF/VF040
FIGURE 1: Functional Block Diagram
SST39LF/VF512 SST39LF/VF010 SST39LF/VF020 SST39LF/VF040
A7
A7
5
A14
A14
A14
A14
A6
A6
A6
A6
6
28
A13
A13
A13
A13
A5
A5
A5
A5
7
27
A8
A8
A8
A8
A4
A4
A4
A4
8
26
A9
A9
A9
A9
A3
A3
A3
A3
9
25
A11
A11
A11
A11
A2
A2
A2
A2
10
24
OE#
OE#
OE#
OE#
A1
A1
A1
A1
11
23
A10
A10
A10
A10
A0
A0
A0
A0
12
22
CE#
CE#
CE#
CE#
DQ0
DQ0
DQ0
DQ0
13
21
14 15 16 17 18 19 20
DQ7
DQ7
DQ7
DQ7
DQ5
1150 32-plcc NH P4.3
DQ6
DQ6
DQ6
DQ5
DQ5
DQ5
DQ4
DQ4
DQ4
DQ4
VSS
DQ3
DQ3
VSS
VSS
DQ3
VSS
DQ3
DQ2
DQ2
DQ2
DQ2
DQ1
DQ1
DQ1
DQ1
32-lead PLCC
Top View
DQ6
A7
SST39LF/VF040 SST39LF/VF020 SST39LF/VF010 SST39LF/VF512
A7
FIGURE 2: Pin Assignments for 32-lead PLCC
©2010 Silicon Storage Technology, Inc.
S71150-14-000
4
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
SST39LF/VF040 SST39LF/VF020 SST39LF/VF010 SST39LF/VF512
A11
A9
A8
A13
A14
A17
WE#
VDD
A18
A16
A15
A12
A7
A6
A5
A4
A11
A9
A8
A13
A14
A17
WE#
VDD
NC
A16
A15
A12
A7
A6
A5
A4
A11
A9
A8
A13
A14
NC
WE#
VDD
NC
A16
A15
A12
A7
A6
A5
A4
A11
A9
A8
A13
A14
NC
WE#
VDD
NC
NC
A15
A12
A7
A6
A5
A4
SST39LF/VF512 SST39LF/VF010 SST39LF/VF020 SST39LF/VF040
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Standard Pinout
Top View
Die Up
OE#
A10
CE#
DQ7
DQ6
DQ5
DQ4
DQ3
VSS
DQ2
DQ1
DQ0
A0
A1
A2
A3
OE#
A10
CE#
DQ7
DQ6
DQ5
DQ4
DQ3
VSS
DQ2
DQ1
DQ0
A0
A1
A2
A3
OE#
A10
CE#
DQ7
DQ6
DQ5
DQ4
DQ3
VSS
DQ2
DQ1
DQ0
A0
A1
A2
A3
OE#
A10
CE#
DQ7
DQ6
DQ5
DQ4
DQ3
VSS
DQ2
DQ1
DQ0
A0
A1
A2
A3
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
1150 32-tsop WH P1.0
FIGURE 3: Pin Assignments for 32-lead TSOP (8mm x 14mm)
TOP VIEW (balls facing down)
SST39LF/VF010
SST39LF/VF020
A14 A13 A15 A16 NC NC
6
NC VSS
5
2
1
WE# NC NC NC DQ5 NC VDD DQ4
NC NC NC NC DQ2 DQ3 VDD NC
A7 NC A6
A5 DQ0 NC
NC DQ1
A3 A4 A2
A1
A0 CE# OE# VSS
A
D
E
B
C
F
G
NC VSS
A9 A8 A11 A12 NC A10 DQ6 DQ7
1150 48-tfbga B3K P2.0
A9 A8 A11 A12 NC A10 DQ6 DQ7
4
3
A14 A13 A15 A16 A17 NC
5
4
WE# NC NC NC DQ5 NC VDD DQ4
3
NC NC NC NC DQ2 DQ3 VDD NC
2
1
H
A7 NC A6
A5 DQ0 NC
A3 A4 A2
A1
A0 CE# OE# VSS
A
D
E
B
C
F
NC DQ1
G
1150 48-tfbga B3K P3.0
6
TOP VIEW (balls facing down)
H
TOP VIEW (balls facing down)
SST39LF/VF040
6
A14 A13 A15 A16 A17 NC
NC VSS
A9 A8 A11 A12 NC A10 DQ6 DQ7
4
3
2
1
WE# NC NC NC DQ5 NC VDD DQ4
NC NC NC NC DQ2 DQ3 VDD NC
A7 A18 A6
A5 DQ0 NC
A3 A4 A2
A1
A0 CE# OE# VSS
A
D
E
B
C
F
NC DQ1
G
1150 48-tfbga B3K P4.0
5
H
FIGURE 4: Pin Assignment for 48-ball TFBGA (6mm x 8mm) for 1 Mbit, 2 Mbit, and 4 Mbit
©2010 Silicon Storage Technology, Inc.
S71150-14-000
5
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
TOP VIEW (balls facing down)
6
A2
A8
A9
A14
A13
A11
NC1
OE#
A10
CE#
5
A1
A17
A0
VDD WE#
DQ3 DQ4
CE#
A16
A18
DQ2
VSS
A12
A15
A7
A6
A5
A4
NC2
A3
A2
A1
B
C
D
E
F
G
H
DQ7 DQ5 DQ6
4
VSS
2
DQ0 DQ1
A0
1
A
1150 34-wfbga MM P5.0
3
J
Note: For SST39LF020, ball B3 is "No Connect"
For SST39LF010, balls B3 and A5 are "No Connect"
FIGURE 5: Pin Assignment for 34-ball WFBGA (4mm x 6mm) for 1 Mbit and 2 Mbit
TABLE 2: Pin Description
Symbol
Pin Name
Functions
AMS1-A0
Address Inputs
To provide memory addresses. During Sector-Erase AMS-A12 address lines will select the
sector. During Block-Erase AMS-A16 address lines will select the block.
DQ7-DQ0
Data Input/output
To output data during Read cycles and receive input data during Write cycles.
Data is internally latched during a Write cycle.
The outputs are in tri-state when OE# or CE# is high.
CE#
Chip Enable
To activate the device when CE# is low.
OE#
Output Enable
To gate the data output buffers.
WE#
Write Enable
To control the Write operations.
VDD
Power Supply
To provide power supply voltage:
VSS
Ground
NC
No Connection
3.0-3.6V for SST39LF512/010/020/040
2.7-3.6V for SST39VF512/010/020/040
Unconnected pins.
T2.1 1150
1. AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010, A17 for SST39LF/VF020, and A18 for SST39LF/VF040
TABLE 3: Operation Modes Selection
Mode
CE#
OE#
WE#
DQ
Address
Read
VIL
VIL
VIH
DOUT
AIN
Program
VIL
VIH
VIL
DIN
AIN
Erase
VIL
VIH
VIL
X1
Sector address,
XXH for Chip-Erase
Standby
VIH
X
X
High Z
X
X
VIL
X
High Z/ DOUT
X
X
X
VIH
High Z/ DOUT
X
VIL
VIL
VIH
Write Inhibit
Product Identification
Software Mode
See Table 4
T3.4 1150
1. X can be VIL or VIH, but no other value.
©2010 Silicon Storage Technology, Inc.
S71150-14-000
6
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
TABLE 4: Software Command Sequence
Command
Sequence
1st Bus
Write Cycle
Addr1
Data
2nd Bus
Write Cycle
Addr1
Data
3rd Bus
Write Cycle
Addr1
4th Bus
Write Cycle
Data
Addr1
Data
Data
5th Bus
Write Cycle
6th Bus
Write Cycle
Addr1
Data
Addr1
Data
Byte-Program
5555H
AAH
2AAAH
55H
5555H
A0H
BA2
Sector-Erase
5555H
AAH
2AAAH
55H
5555H
80H
5555H
AAH
2AAAH
55H
SAX3
30H
5555H
AAH
2AAAH
55H
5555H
10H
Chip-Erase
5555H
AAH
2AAAH
55H
5555H
80H
Software ID Entry4,5
5555H
AAH
2AAAH
55H
5555H
90H
2AAAH
55H
5555H
F0H
Software ID Exit6
XXH
F0H
Software ID Exit6
5555H
AAH
T4.2 1150
1. Address format A14-A0 (Hex),
Address A15 can be VIL or VIH, but no other value, for the Command sequence for SST39LF/VF512.
Addresses AMS-A15 can be VIL or VIH, but no other value, for the Command sequence.
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010, A17 for SST39LF/VF020, and A18 for SST39LF/VF040
2. BA = Program Byte address
3. SAX for Sector-Erase; uses AMS-A12 address lines
4. The device does not remain in Software Product ID mode if powered down.
5. With AMS-A1 = 0; SST Manufacturer’s ID = BFH, is read with A0 = 0,
SST39LF/VF512 Device ID = D4H, is read with A0 = 1,
SST39LF/VF010 Device ID = D5H, is read with A0 = 1,
SST39LF/VF020 Device ID = D6H, is read with A0 = 1,
SST39LF/VF040 Device ID = D7H, is read with A0 = 1.
6. Both Software ID Exit operations are equivalent
Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum Stress
Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at
these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.)
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C
D. C. Voltage on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V
Transient Voltage (<20 ns) on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2.0V to VDD+2.0V
Voltage on A9 Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.5V to 13.2V
Package Power Dissipation Capability (Ta = 25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0W
Surface Mount Solder Reflow Temperature1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260°C for 10 seconds
Output Short Circuit Current2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
1. Excluding certain with-Pb 32-PLCC units, all packages are 260°C capable in both non-Pb and with-Pb solder versions.
Certain with-Pb 32-PLCC package types are capable of 240°C for 10 seconds; please consult the factory for the latest information.
2. Outputs shorted for no more than one second. No more than one output shorted at a time.
Operating Range for SST39LF512/010/020/040
Range
Commercial
Ambient Temp
VDD
0°C to +70°C
3.0-3.6V
AC Conditions of Test
Input Rise/Fall Time . . . . . . . . . . . . . . . 5 ns
Output Load
CL = 30 pF for SST39LF512/010/020/040
CL = 100 pF for SST39VF512/010/020/040
Operating Range for SST39VF512/010/020/040
Range
Commercial
Industrial
Ambient Temp
VDD
0°C to +70°C
2.7-3.6V
-40°C to +85°C
2.7-3.6V
See Figures 15 and 16
©2010 Silicon Storage Technology, Inc.
S71150-14-000
7
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
TABLE 5: DC Operating Characteristics -VDD = 3.0-3.6V for SST39LF512/010/020/040 and 2.7-3.6V for
SST39VF512/010/020/0401
Limits
Symbol
Parameter
IDD
Power Supply Current
Min
Max
Units
Test Conditions
Address input=VILT/VIHT, at f=1/TRC Min
VDD=VDD Max
Read2
20
mA
CE#=VIL, OE#=WE#=VIH, all I/Os open
Program and Erase3
30
mA
CE#=WE#=VIL, OE#=VIH
ISB
Standby VDD Current
15
µA
CE#=VIHC, VDD=VDD Max
ILI
Input Leakage Current
1
µA
VIN=GND to VDD, VDD=VDD Max
ILO
Output Leakage Current
10
µA
VOUT=GND to VDD, VDD=VDD Max
VIL
Input Low Voltage
0.8
V
VDD=VDD Min
VIH
Input High Voltage
0.7VDD
V
VDD=VDD Max
VIHC
Input High Voltage (CMOS)
VDD-0.3
V
VDD=VDD Max
VOL
Output Low Voltage
VOH
Output High Voltage
0.2
VDD-0.2
V
IOL=100 µA, VDD=VDD Min
V
IOH=-100 µA, VDD=VDD Min
T5.7 1150
1. Typical conditions for the Active Current shown on the front data sheet page are average values at 25°C
(room temperature), and VDD = 3V for VF devices. Not 100% tested.
2. Values are for 70 ns conditions. See the Multi-Purpose Flash Power Rating application note for further information.
3. 30 mA max for Erase operations in the industrial temperature range.
TABLE 6: Recommended System Power-up Timings
Symbol
Parameter
Minimum
Units
TPU-READ1
Power-up to Read Operation
100
µs
Power-up to Program/Erase Operation
100
µs
TPU-WRITE
1
T6.1 1150
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
TABLE 7: Capacitance (Ta = 25°C, f=1 Mhz, other pins open)
Parameter
CI/O
1
CIN1
Description
Test Condition
Maximum
I/O Pin Capacitance
VI/O = 0V
12 pF
Input Capacitance
VIN = 0V
6 pF
T7.0 1150
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
TABLE 8: Reliability Characteristics
Symbol
Parameter
Minimum Specification
Units
Test Method
NEND1,2
Endurance
10,000
Cycles
JEDEC Standard A117
TDR1
Data Retention
100
Years
JEDEC Standard A103
ILTH1
Latch Up
100 + IDD
mA
JEDEC Standard 78
T8.3 1150
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
2. NEND endurance rating is qualified as a 10,000 cycle minimum for the whole device. A sector- or block-level rating would result in a
higher minimum specification.
©2010 Silicon Storage Technology, Inc.
S71150-14-000
8
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
AC CHARACTERISTICS
TABLE 9: Read Cycle Timing Parameters - VDD = 3.0-3.6V for SST39LF512/010/020/040 and 2.7-3.6V for
SST39VF512/010/020/040
SST39LF512-45
SST39LF010-45
SST39LF020-45
SST39LF040-45
SST39LF020-55
SST39LF040-55
Min
Min
Symbol Parameter
Max
45
SST39VF512-70
SST39VF010-70
SST39VF020-70
SST39VF040-70
Max
Min
55
Max
Units
TRC
Read Cycle Time
TCE
Chip Enable Access Time
TAA
Address Access Time
45
55
70
ns
TOE
Output Enable Access Time
30
30
35
ns
TCLZ1
CE# Low to Active Output
0
0
0
ns
TOLZ1
OE# Low to Active Output
0
0
0
ns
45
70
55
ns
70
ns
1
CE# High to High-Z Output
15
15
25
ns
TOHZ1
OE# High to High-Z Output
15
15
25
ns
TOH1
Output Hold from Address Change
TCHZ
0
0
0
ns
T9.2 1150
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
TABLE 10: Program/Erase Cycle Timing Parameters
Symbol
Parameter
TBP
Byte-Program Time
TAS
Address Setup Time
0
ns
TAH
Address Hold Time
30
ns
TCS
WE# and CE# Setup Time
0
ns
TCH
WE# and CE# Hold Time
0
ns
TOES
OE# High Setup Time
0
ns
TOEH
OE# High Hold Time
10
ns
TCP
CE# Pulse Width
40
ns
TWP
WE# Pulse Width
40
ns
TWPH1
WE# Pulse Width High
30
ns
TCPH1
CE# Pulse Width High
30
ns
TDS
Data Setup Time
40
ns
TDH1
Data Hold Time
0
ns
1
Min
Max
Units
20
µs
Software ID Access and Exit Time
150
ns
TSE
Sector-Erase
25
ms
TSCE
Chip-Erase
100
ms
TIDA
T10.1 1150
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
©2010 Silicon Storage Technology, Inc.
S71150-14-000
9
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
TRC
TAA
ADDRESS AMS-0
TCE
CE#
TOE
OE#
TOHZ
TOLZ
VIH
WE#
TCLZ
DQ7-0
Note:
TOH
HIGH-Z
TCHZ
DATA VALID
HIGH-Z
DATA VALID
1150 F03.0
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010,
A17 for SST39LF/VF020 and A18 for SST39LF/VF040
FIGURE 6: Read Cycle Timing Diagram
INTERNAL PROGRAM OPERATION STARTS
TBP
5555
ADDRESS AMS-0
2AAA
5555
ADDR
TAH
TDH
TWP
WE#
TAS
TDS
TWPH
OE#
TCH
CE#
TCS
DQ7-0
Note:
AA
55
A0
DATA
SW0
SW1
SW2
BYTE
(ADDR/DATA)
1150 F04.0
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010,
A17 for SST39LF/VF020 and A18 for SST39LF/VF040
FIGURE 7: WE# Controlled Program Cycle Timing Diagram
©2010 Silicon Storage Technology, Inc.
S71150-14-000
10
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
INTERNAL PROGRAM OPERATION STARTS
TBP
5555
ADDRESS AMS-0
2AAA
5555
ADDR
TAH
TDH
TCP
CE#
TAS
TDS
TCPH
OE#
TCH
WE#
TCS
DQ7-0
Note:
AA
55
A0
DATA
SW0
SW1
SW2
BYTE
(ADDR/DATA)
1150 F05.0
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010,
A17 for SST39LF/VF020 and A18 for SST39LF/VF040
FIGURE 8: CE# Controlled Program Cycle Timing Diagram
ADDRESS AMS-0
TCE
CE#
TOEH
TOES
OE#
TOE
WE#
D
DQ7
Note:
D#
D#
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010,
A17 for SST39LF/VF020 and A18 for SST39LF/VF040
D
1150 F06.0
FIGURE 9: Data# Polling Timing Diagram
©2010 Silicon Storage Technology, Inc.
S71150-14-000
11
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
ADDRESS AMS-0
TCE
CE#
TOEH
TOES
TOE
OE#
WE#
DQ6
TWO READ CYCLES
Note:
WITH SAME OUTPUTS
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010,
A17 for SST39LF/VF020 and A18 for SST39LF/VF040
1150 F07.0
FIGURE 10: Toggle Bit Timing Diagram
TSE
SIX-BYTE CODE FOR SECTOR-ERASE
5555
ADDRESS AMS-0
2AAA
5555
5555
2AAA
SAX
CE#
OE#
TWP
WE#
DQ7-0
AA
55
80
AA
55
30
SW0
SW1
SW2
SW3
SW4
SW5
1150 F08.0
Note: This device also supports CE# controlled Sector-Erase operation. The WE# and CE# signals are
interchageable as long as minmum timings are met. (See Table 10)
SAX = Sector Address
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010, A17 for SST39LF/VF020, and A18 for SST39LF/VF040
FIGURE 11: WE# Controlled Sector-Erase Timing Diagram
©2010 Silicon Storage Technology, Inc.
S71150-14-000
12
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
TSCE
SIX-BYTE CODE FOR CHIP-ERASE
ADDRESS AMS-0
5555
2AAA
5555
5555
2AAA
5555
CE#
OE#
TWP
WE#
DQ7-0
AA
55
80
AA
55
10
SW0
SW1
SW2
SW3
SW4
SW5
1150 F17.0
Note: This device also supports CE# controlled Chip-Erase operation. The WE# and CE# signals are
interchageable as long as minmum timings are met. (See Table 10)
AMS = Most significant address
AMS = A15 for SST39LF/VF512, A16 for SST39LF/VF010, A17 for SST39LF/VF020, and A18 for SST39LF/VF040
FIGURE 12: WE# Controlled Chip-Erase Timing Diagram
Three-byte Sequence for
Software ID Entry
ADDRESS A14-0
5555
2AAA
5555
0000
0001
CE#
OE#
TIDA
TWP
WE#
TWPH
DQ7-0
TAA
AA
55
90
SW0
SW1
SW2
BF
Device ID
1150 F09.2
Note: Device ID = D4H for SST39LF/VF512, D5H for SST39LF/VF010, D6H for SST39LF/VF020, and D7H for SST39LF/VF040.
FIGURE 13: Software ID Entry and Read
©2010 Silicon Storage Technology, Inc.
S71150-14-000
13
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
THREE-BYTE SEQUENCE FOR
SOFTWARE ID EXIT AND RESET
5555
ADDRESS A14-0
2AAA
AA
DQ7-0
5555
55
F0
TIDA
CE#
OE#
TWP
WE#
TWHP
SW0
SW1
SW2
1150 F10.0
FIGURE 14: Software ID Exit and Reset
VIHT
INPUT
VIT
REFERENCE POINTS
VOT
OUTPUT
VILT
1150 F12.1
AC test inputs are driven at VIHT (0.9 VDD) for a logic “1” and VILT (0.1 VDD) for a logic “0”. Measurement reference points
for inputs and outputs are VIT (0.5 VDD) and VOT (0.5 VDD). Input rise and fall times (10% ↔ 90%) are <5 ns.
Note: VIT - VINPUT Test
VOT - VOUTPUT Test
VIHT - VINPUT HIGH Test
VILT - VINPUT LOW Test
FIGURE 15: AC Input/Output Reference Waveforms
TO TESTER
TO DUT
CL
1150 F11.1
FIGURE 16: A Test Load Example
©2010 Silicon Storage Technology, Inc.
S71150-14-000
14
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
Start
Load data: AAH
Address: 5555H
Load data: 55H
Address: 2AAAH
Load data: A0H
Address: 5555H
Load Byte
Address/Byte
Data
Wait for end of
Program (TBP,
Data# Polling
bit, or Toggle bit
operation)
Program
Completed
1150 F13.1
FIGURE 17: Byte-Program Algorithm
©2010 Silicon Storage Technology, Inc.
S71150-14-000
15
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
Internal Timer
Toggle Bit
Data# Polling
Byte-Program/
Erase
Initiated
Byte-Program/
Erase
Initiated
Byte-Program/
Erase
Initiated
Read byte
Read DQ7
Wait TBP,
TSCE, or TSE
Read same
byte
Program/Erase
Completed
No
Is DQ7 =
true data?
Yes
No
Does DQ6
match?
Program/Erase
Completed
Yes
Program/Erase
Completed
1150 F14.0
FIGURE 18: Wait Options
©2010 Silicon Storage Technology, Inc.
S71150-14-000
16
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
Software ID Entry
Command Sequence
Software ID Exit &
Reset Command Sequence
Load data: AAH
Address: 5555H
Load data: AAH
Address: 5555H
Load data: F0H
Address: XXH
Load data: 55H
Address: 2AAAH
Load data: 55H
Address: 2AAAH
Wait TIDA
Load data: 90H
Address: 5555H
Load data: F0H
Address: 5555H
Return to normal
operation
Wait TIDA
Wait TIDA
Read Software ID
Return to normal
operation
1150 F15.2
FIGURE 19: Software ID Command Flowcharts
©2010 Silicon Storage Technology, Inc.
S71150-14-000
17
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
Chip-Erase
Command Sequence
Sector-Erase
Command Sequence
Load data: AAH
Address: 5555H
Load data: AAH
Address: 5555H
Load data: 55H
Address: 2AAAH
Load data: 55H
Address: 2AAAH
Load data: 80H
Address: 5555H
Load data: 80H
Address: 5555H
Load data: AAH
Address: 5555H
Load data: AAH
Address: 5555H
Load data: 55H
Address: 2AAAH
Load data: 55H
Address: 2AAAH
Load data: 10H
Address: 5555H
Load data: 30H
Address: SAX
Wait TSCE
Wait TSE
Chip erased
to FFH
Sector erased
to FFH
1150 F16.1
FIGURE 20: Erase Command Sequence
©2010 Silicon Storage Technology, Inc.
S71150-14-000
18
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
PRODUCT ORDERING INFORMATION
SST
39
XX
LF
040
XX XXXX
- 45
- XXX
-
4C
XX
NH
- XXX
E
X
Environmental Attribute
E1 = non-Pb
Package Modifier
H = 32 leads
K = 48 balls
M = 34 balls (54 possible positions)
Package Type
B3 = TFBGA (0.8mm pitch, 6mm x 8mm)
N = PLCC
M = WFBGA (0.5mm pitch, 4mm x 6mm)
W = TSOP (type 1, die up, 8mm x 14mm)
Temperature Range
C = Commercial = 0°C to +70°C
I = Industrial = -40°C to +85°C
Minimum Endurance
4 = 10,000 cycles
Read Access Speed
45 = 45 ns
55 = 55 ns
70 = 70 ns
Device Density
040 = 4 Mbit
020 = 2 Mbit
010 = 1 Mbit
512 = 512 Kbit
Voltage
L = 3.0-3.6V
V = 2.7-3.6V
Product Series
39 = Multi-Purpose Flash
1. Environmental suffix “E” denotes non-Pb solder. SST
non-Pb solder devices are RoHS compliant.
©2010 Silicon Storage Technology, Inc.
S71150-14-000
19
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
Valid combinations for SST39LF512
SST39LF512-45-4C-NHE
SST39LF512-45-4C-WHE
Valid combinations for SST39VF512
SST39VF512-70-4C-NHE
SST39VF512-70-4C-WHE
SST39VF512-70-4I-NHE
SST39VF512-70-4I-WHE
Valid combinations for SST39LF010
SST39LF010-45-4C-NHE
SST39LF010-45-4C-WHE
SST39LF010-45-4C-B3KE
SST39LF010-45-4C-MME
Valid combinations for SST39VF010
SST39VF010-70-4C-NHE
SST39VF010-70-4C-WHE
SST39VF010-70-4C-B3KE
SST39VF010-70-4I-NHE
SST39VF010-70-4I-WHE
SST39VF010-70-4I-B3KE
Valid combinations for SST39LF020
SST39LF020-45-4C-NHE
SST39LF020-45-4C-WHE
SST39LF020-55-4C-NHE
SST39LF020-55-4C-WHE
SST39LF020-45-4C-B3KE
SST39LF020-45-4C-MME
Valid combinations for SST39VF020
SST39VF020-70-4C-NHE
SST39VF020-70-4C-WHE
SST39VF020-70-4C-B3KE
SST39VF020-70-4I-NHE
SST39VF020-70-4I-WHE
SST39VF020-70-4I-B3KE
Valid combinations for SST39LF040
SST39LF040-45-4C-NHE
SST39LF040-45-4C-WHE
SST39LF040-55-4C-NHE
SST39LF040-55-4C-WHE
SST39LF040-45-4C-B3KE
Valid combinations for SST39VF040
SST39VF040-70-4C-NHE
SST39VF040-70-4C-WHE
SST39VF040-70-4C-B3KE
SST39VF040-70-4I-NHE
SST39VF040-70-4I-WHE
SST39VF040-70-4I-B3KE
Note: Valid combinations are those products in mass production or will be in mass production. Consult your SST sales
representative to confirm availability of valid combinations and to determine availability of new combinations.
©2010 Silicon Storage Technology, Inc.
S71150-14-000
20
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
PACKAGING DIAGRAMS
TOP VIEW
SIDE VIEW
.495
.485
.453
.447
Optional
Pin #1
Identifier .048
.042
2
1
32
.112
.106
.020 R.
MAX.
.029 x 30˚
.023
.040 R.
.030
.042
.048
.595 .553
.585 .547
BOTTOM VIEW
.021
.013
.400 .530
BSC .490
.032
.026
.050
BSC
.015 Min.
.095
.075
.050
BSC
.032
.026
.140
.125
Note: 1. Complies with JEDEC publication 95 MS-016 AE dimensions, although some dimensions may be more stringent.
2. All linear dimensions are in inches (max/min).
3. Dimensions do not include mold flash. Maximum allowable mold flash is .008 inches.
4. Coplanarity: 4 mils.
32-plcc-NH-3
FIGURE 21: 32-lead Plastic Lead Chip Carrier (PLCC)
SST Package Code: NH
TOP VIEW
BOTTOM VIEW
8.00 ± 0.20
5.60
0.45 ± 0.05
(48X)
0.80
6
6
5
5
4.00
4
4
6.00 ± 0.20
3
3
2
2
1
1
0.80
A B C D E F G H
A1 CORNER
SIDE VIEW
H G F E D C B A
A1 CORNER
1.10 ± 0.10
0.12
SEATING PLANE
1mm
0.35 ± 0.05
Note:
1. Complies with JEDEC Publication 95, MO-210, variant 'AB-1', although some dimensions may be more stringent.
2. All linear dimensions are in millimeters.
3. Coplanarity: 0.12 mm
4. Ball opening size is 0.38 mm (± 0.05 mm)
48-tfbga-B3K-6x8-450mic-4
FIGURE 22: 48-ball Thin-profile, Fine-pitch Ball Grid Array (TFBGA) 6mm x 8mm
SST Package Code: B3K
©2010 Silicon Storage Technology, Inc.
S71150-14-000
21
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
1.05
0.95
Pin # 1 Identifier
0.50
BSC
8.10
7.90
0.27
0.17
0.15
0.05
12.50
12.30
DETAIL
1.20
max.
0.70
0.50
14.20
13.80
0˚- 5˚
0.70
0.50
Note:
1. Complies with JEDEC publication 95 MO-142 BA dimensions,
although some dimensions may be more stringent.
1mm
2. All linear dimensions are in millimeters (max/min).
3. Coplanarity: 0.1 mm
4. Maximum allowable mold flash is 0.15 mm at the package ends, and 0.25 mm between leads.
32-tsop-WH-7
FIGURE 23: 32-lead Thin Small Outline Package (TSOP) 8mm x 14mm
SST Package Code: WH
©2010 Silicon Storage Technology, Inc.
S71150-14-000
22
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
TOP VIEW
BOTTOM VIEW
6.00 ± 0.08
4.00
0.50
6
5
4
3
2
1
4.00 ± 0.08
0.50
J H G F E D C B A
A1 INDICATOR4
A1 CORNER
DETAIL
6
5
4
3
2
1
2.50
A B C D E F G H J
0.32 ± 0.05
(34X)
0.63 ± 0.10
SIDE VIEW
0.08
SEATING PLANE
0.20 ± 0.06
Note:
1mm
1. Although many dimensions are similar to those of JEDEC Publication 95, MO-225, this specific package is not registered.
2. All linear dimensions are in millimeters.
3. Coplanarity: 0.08 mm
4. No ball is present in position A1; a gold-colored indicator is present.
34-wfbga-MM-4x6-32mic-1
5. Ball opening size is 0.29 mm (± 0.05 mm)
FIGURE 24: 34-ball Very-very-thin-profile, Fine-pitch Ball Grid Array (WFBGA) 4mm x 6mm x .63mm
SST Package Code: MM
©2010 Silicon Storage Technology, Inc.
S71150-14-000
23
01/10
512 Kbit / 1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
SST39LF512 / SST39LF010 / SST39LF020 / SST39LF040
SST39VF512 / SST39VF010 / SST39VF020 / SST39VF040
Data Sheet
TABLE 11: Revision History
Number
Description
Date
01
•
2000 Data Book
Feb 2000
02
•
Changed speed from 45 ns to 55 ns for the SST39LF020 and SST39LF040
Aug 2000
03
•
2002 Data Book: Reintroduced the 45 ns parts for the SST39LF020 and SST39LF040 Feb 2002
04
•
•
Added the B3K package for the 2 Mbit devices
Added footnote in Table 5 to indicate IDD Write is 30 mA max for Erase operations in
the Industrial temperature range.
05
•
Changes to Table 5 on page 8
– Added footnote for MPF power usage and Typical conditions
– Clarified the Test Conditions for Power Supply Current and Read parameters
– Clarified IDD Write to be Program and Erase
– Corrected IDD Program and Erase from 20 mA to 30 mA
•
Part number changes - see page 20 for additional information
Oct 2002
Mar 2003
06
•
Added new “MM” Micro-Package MPNs for 1M and 2M LF parts- see page 20
Oct 2003
07
•
•
•
2004 Data Book
Added non-Pb MPNs and removed footnote (See page 20)
Updated B3K and MM package diagrams
Nov 2003
08
•
•
•
•
•
Added RoHS Compliant statement.
Added 4 MBit to Figure 4.
Revised Absolute Max Stress Ratings for Surface Mount Solder Reflow Temperature
Removed SST39VFxxx-90 Timing Parameters from Figure 9.
Added Footnote and removed Read Access Speed 90 = 90 to Product Ordering Information.
Removed 90 part numbers Valid Combinations lists
Dec 2005
•
09
•
Edited page Valid Combinations on page 21. Changed 39LF040-70-4C-B3KE to
39LF040-45-4C-B3KE
Jan 2006
10
•
Removed leaded parts
Nov 2008
11
•
Added package YME
Feb 2009
12
•
Revised “Product Ordering Information” on page 19
Apr 2009
13
•
Changed endurance from 10,000 to 100,000 in Product Description, page 1
Sep 2009
14
•
EOL of SST39LF010-45-4C-YME. Replacement part is SST39LF010-45-4C-MME in
this document.
Removed all references to the YME package.
Jan 2010
•
Silicon Storage Technology, Inc. • 1171 Sonora Court • Sunnyvale, CA 94086 • Telephone 408-735-9110 • Fax 408-735-9036
www.SuperFlash.com or www.sst.com
©2010 Silicon Storage Technology, Inc.
S71150-14-000
24
01/10