40 WATT MEDICAL POWER SUPPLIES DESCRIPTION PM40AL SERIES (MDD) The PM40AL series of compact, open PCB constructed, AC-DC switching power supplies are capable of delivering 40 watts of continuous output power. They operate at 85 to 264 VAC input voltage without the need of voltage selection. They are ideally suited for use in medical equipment, safety systems and monitoring equipment, not for patient contact. F E ATU R E S ‧ ‧ ‧ ‧ ‧ ‧ ‧ Low safety ground leakage current 100% burn-in W i d e i n p u t r a n g e 8 5 t o 2 6 4 VA C Input surge current protection Overvoltage protection Overcurrent protection Open PCB construction S a f e t y St a n d a r d A p p ro v a ls ： I N P U T S P E C I F I C ATI O N S Input voltage： Input frequency： Input current： 85 to 264 VAC UL 2601-1 47 to 63 Hz Leakage current： 1.20A（rms）for 115VAC CSA C22.2 No. 601.1 0.70A（rms）for 230VAC 150uA max. @ 230VAC, 50Hz TÜV EN60601-1 90 uA max. @ 115VAC, 60Hz GENERAL SPECIFICATIONS OUTPUT SPECIFICATIONS Output voltage/current： See rating chart Total output power： Ripple and noise： Overvoltage protection： 40 watts maximum 1﹪ peak to peak maximum Provided on output #1 only; set at 112 - 132﹪ of its nominal output voltage All outputs protected to short circuit conditions All outputs ±0.04﹪ /℃ maximum Maximum excursion of 4﹪ or better on all models, recovering to 1﹪ of final value within 500us after a 25﹪ step load change Overcurrent protection： Temperature coefficient： Transient response： E N V I R O N M E N TA L S P E C I F I C ATI O N S Operating temperature： Storage temperature： Relative humidity： Derating： 0℃ to +70℃ -40℃ to +85℃ 5﹪to 95﹪non-condensing Derate from 100﹪ at +50℃ linearly to 50% at +70℃ Switching frequency： 36KHz ±5KHz Efficiency： 70﹪ minimum on single output models with Vo≧ 15V, 65% minimum on the others 10 msec minimum at 110VAC ±0.5﹪ maximum at full load Hold-up time： Line regulation： Inrush current： 15 amps @ 115VAC, or 30 amps @ 230VAC, at 25℃ cold start Withstand voltage： 4000VAC from input to output 1500VAC from input to ground 500VAC from output to ground MTBF： 600,000 hours minimum at full load at 25℃ ambient, calculated per MIL-HDBK-217F EMC Performance (EN60601-1-2: 2001) Class B conducted, class B radiated EN55011 Class B conducted, class B radiated FCC Class B conducted, class B radiated VCCI Harmonic distortion, class A and D EN61000-3-2 Line flicker EN61000-3-3 ESD, ± 8KV air and ± 6KV contact EN61000-4-2 Radiated immunity, 3V/m for 80~2500MHz EN61000-4-3 Fast transient/burst, ± 2KV EN61000-4-4 Surge, ± 1KV diff., ± 2KV com. EN61000-4-5 Conducted immunity, 3Vrms EN61000-4-6 Magnetic field immunity, 3A/m EN61000-4-8 Voltage dips, 30% reduction for 500ms, EN61000-4-11 60% reduction for 100ms and >95% reduction for 10ms Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● [email protected] ● www.TRUMPower.com PM40AL SERIES MEDICAL GRADE OUTPUT VOLTAGE/CURRENT RATING CHART Output #1 Imin. Imax. 0A 8.0A Vnom. 5V PM40-12AL 12V 0A 3.5A 1% (N/A) (N/A) 40W PM40-13AL 15V 0A 3.0A 1% (N/A) (N/A) 40W PM40-14AL 24V 0A 2.0A 1% (N/A) (N/A) 40W PM40-18AL 48V 0A 0.9A 1% (N/A) (N/A) 40W PM40-23AL +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% (N/A) 40W PM40-24AL +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% (N/A) 40W PM40-25AL +5V 0.5A 3.0A 3% +24V 0.1A 1A 5% (N/A) 40W Tol. 2% Vnom. Output #2 Imin. Imax. (N/A) Tol. Vnom. Output #3 Imin. Imax. (N/A) Maximum Output Power 40W (1)(2) Model PM40-10AL Tol. PM40-30AL +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% -5V 0.05A 0.3A 10% 40W PM40-31AL +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% -12V 0.05A 0.3A 10% 40W PM40-32AL +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% -15V 0.05A 0.3A 10% 40W PM40-33AL +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% -12V 0.05A 0.3A 10% 40W PM40-39AL +5V 0.5A 3.0A 3% +24V 0.1A 1A 5% -12V 0.05A 0.3A 10% 40W Notes: (1) All multiple output models may be operated at no-load without damage. At no-load, output voltage tolerance increases to 10% (2) Safety agency approvals are for the above listed models in PCB format. To order a model with a metallic L-bracket or box, change suffix “AL” to “BL” for L-bracket format or to “CL” for enclosed format (mechanical details shown in page 7-1), e.g. PM40-14BL. MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Input connector mates with Molex housing 09-50-3031 and Molex 2878 series crimp terminal. 4. Output connector mates with Molex housing 09-50-3061 and Molex 2878 series crimp terminal. 5. Weight: 230 grams (PCB format) 6. It’s strongly recommended to connect the two “＊” marked mounting holes to system chassis through metallic stand-offs. This helps reduce greatly output noise. PIN CHART PIN MODEL PM40-10AL PM40-13AL PM40-18AL PM40-23AL PM40-25AL PM40-30AL PM40-32AL PM40-39AL 1 2 3 4 5 6 OUTPUT #1 OUTPUT #1 OUTPUT #1 RETURN RETURN RETURN PM40-24AL OUTPUT #2 OUTPUT #1 OUTPUT #1 COMMON RETURN COMMON RETURN N.C. PM40-31AL PM40-33AL OUTPUT #2 OUTPUT #1 OUTPUT #1 COMMON RETURN COMMON RETURN OUTPUT #3 PM40-12AL PM40-14AL Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● [email protected] ● www.TRUMPower.com