TRU050 Complete VCXO based Phase-Locked Loop Features • Output Frequencies to 65.536 MHz • 5.0 V or 3.3Vdc Operation • Tri-State Output • Holdover on Loss of Signal Alarm • VCXO with CMOS Outputs • 0/70° or –40/85°C Temperature Range • Ceramic SMD Package • RoHS/Lead Free Compliant The TRU050, VCXO based PLL Description Applications The VI TRU050 is a user-configurable crystal-based PLL integrated circuit. It includes a digital phase detector, op-amp, VCXO and additional integrated functions for use in digital synchronization applications. Loop filter software is available as well SPICE models for circuit simulation. • Frequency Translation • Clock Smoothing • NRZ Clock Recovery • DSLAM, ADM, ATM, Aggregation, Optical Switching/Routing, Base Station • Low Jitter PLL’s Figure 1. TRU050 Block Diagram Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 1 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Performance Characteristics Table 1. Electrical Performance Parameter Output Frequency (ordering option) Out 1, 5V option Out 1, 3.3V option Supply Voltage 1 +5 +3.3 Supply Current Output Logic Levels Output Logic High2 Output Logic Low2 Output Transition Times Rise Time2 Fall Time2 Input Logic Levels Output Logic High2 Output Logic Low2 Loss of Signal Indication Output Logic High2 Output Logic Low2 Nominal Frequency on Loss of Signal Output 1 Output 2 Symmetry or Duty Cycle3 Out 1 Out 2 RCLK Absolute Pull Range, ordering option over operating temp, aging, power supply Symbol Typical Maximum Units 65.636 51.840 MHz MHz 5.5 3.6 65 V V mA 0.5 V V 5 5 ns ns 0.5 V V 0.5 V V ±75 ±75 ppm ppm 40/60 45/55 40/60 % % % ppm 4.5 3.0 V V ±1 rad/V rad/V °C uA 1.000 1.000 VDD 4.5 3.0 5.0 3.3 IDD VOH VOL 2.5 tR tF VIH VIL 2.0 VOH VOL 2.5 SYM1 SYM2 RCLK APR variations Test Conditions for APR (+5V option) Test Conditions for APR (+3.3V option) Gain Transfer Phase Detector Gain +5V option +3.3V Option Operating temperature, ordering option Control Voltage Leakage Current Min VC VC ±50 ±80 ±100 0.5 0.3 Positive 0.53 0.35 0/70 or –40/85 IVCXO 1. A good quality 0.01uF in parrallel with a 0.1 uf capacitor should be located as close to pin 16 to ground as possible. 2. Figure 1 defines these parameters. Figure 2 illustrates the equivalent five-gate TTL load and operating conditions under which these parameters are tested and specified. Loads greater than 15 pF will adversely effect rise/fall time and duty cycle. 3. Symmetry is defined as (ON TIME/PERIOD with Vs=-1.4 V for both 5V and 3.3V operation. TF TR IDD 650Ω 80 % 16 1.4V V DD 20 % + - .1μF .01μF 1 3 IC On Time VC + - 15pF 1.8k Period Figure 2. Output Waveform Figure 3. OUT1, OUT2, RDATA and RCLK Test Conditions (25±5°C) Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 2 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 2. Absolute Maximum Ratings Parameter Power Supply Storage Temperature Soldering Temperature/Duration Clock and Data Input Range Symbol VDD Tstorage TPEAK / tP CLKIN, DATAIN Ratings 7 -55/125 260 / 40 Gnd-0.5 to VDD +0.5 Unit Vdc °C °C/sec V Reliability The TRU050 is capable of meeting the following qualification tests. Table 3. Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Conditions MIL-STD-883, Method 2002 MIL-STD-883, Method 2007 MIL-STD-883, Method 2003 MIL-STD-883, Method 1014, 100% Tested MIL-STD-883, Method 2016 Handling Precautions Although ESD protection circuitry has been designed into the the TRU050, proper precautions should be taken when handling and mounting. VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Table 4. ESD Ratings Model Human Body Model Charged Device Model Minimum 1500V 1000V MIL-STD 3015 JESD 22-C101 Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 3 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL TRU050 Theory of Operation Phase Detector The phase detector has two buffered inputs, DATAIN and CLKIN, which are designed to switch at 1.4 volts. DATAIN is designed to accept an NRZ data stream but may also be used for clock signals which have about a 50% duty cycle. CLKIN is connected to OUT1 or OUT2, or a divided version of one of these outputs. CLKIN and DATAIN and are protected by ESD diodes and should not exceed the power supply voltage or ground by more than a few hundred millivolts. The phase detector is basically a latched flip flop/exclusive-or gate/differential amplifier filter design to produce a DC signal proportional to the phase between the CLKIN and DATAIN signals, see figure 4 for a block diagram and figure 5 for a open loop transfer curve. This simplies the PLL design as the designer does not have to filter narrow pulse signal to a DC level. Under locked conditions the rising edge CLKIN will be centered in the middle of the DATAIN signal, see figure 6. The phase detector gain is 0.53V/rad x data density for 5volt operation, and 0.35V/rad x data density for 3.3 volt operation. Data density = 1.0 for clock signals and is system dependent on coding and design for NRZ signals, but 0.25 could be used as a starting point for data density. The phase detector output is a DC signal for DATAIN frequencies greater than 1MHz but produces signficant ripple when inputs are less than 200kHz. Additional filtering is required for low input frequency applications such as 8kHz frequency translation, see figures 8 and 9. Under closed loop conditions the active filter has a blocking capacitor which provides a very high DC gain, so under normal locked conditions and input frequencies >1MHz, PHO will be about VDD/2 and will not vary signifigantly with changes in input frequency (within lock range). The control (voltage pin 1) will vary according to the input frequency offset, but PHO will remain relatively constant. Data In (pin 7) D Clock In (pin 9) 20 kΩ Q1 30 kΩ D PHO (pin 6) Q2 Gain = 2 / 3 Gain = 5 V / 2π Figure 4. Simplified Phase Detector Block Diagram Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 4 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Vd VDD −π VDD/2 0 +π Relative Phase (θe) 0V Gain Slope = VDD/ 2π Figure 5. Open Loop Phase Detector Transfer Curve Recovered Clock and Data Alignment Outputs The TRU050 is designed to recover an imbedded clock from an NRZ data signal and retime it with a data pattern. In this application, the VCXO frequency is exactly the same frequency as the NRZ data rate and the outputs are taken off Pin 11, RCLK, and Pin 12, RDATA. Under locked conditions, the falling edge of RCLK is centered in the RDATA pattern. Also, there is a 1.5 clock cyle delay between DATAIN and RDATA. Figure 6 shows the relationship between the DATAIN, CLKIN, RDATA and RCLK. Data In Data1 Clock In Recovered Data Data1 Recovered Clock Figure 6. Clock and Data Timing Relationships for the NRZ data Other RZ encoding schemes such as Manchester or AMI can be accomidated by using a TRU050 at twice the baud rate. Loss of Signal, LOS and LOSIN The LOS circuit provides an output alarm flag when the DATAIN input signal is lost. The LOS output is normally a logic low and is set to a logic high after 256 consecutive clock periods on CLKIN with no detected DATAIN transitions. This signal can be used to either flag external alarm circuits and/or drive the TRU050’s LOSIN input. When LOSIN is set to a logic high, the VCXO control voltage (pin 1) is switched to an internal voltage which centers OUT1 and OUT2 to center frequency +/-75ppm. Also, LOS automatically closes the op amp feedback which means the op-amp is a unity gain buffer and will produce a DC voltage equal to the +op amp voltage (pin 4), usually VDD/2. Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 5 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL VCXO and Absolute Pull Range (APR) Specification The TRU050’s VCXO is a varactor tuned crystal oscillator, which produces an output frequency proportional to the control voltage (pin 1). The frequency deviation of the TRU050 VCXO is specified in terms of Absolute Pull Range (APR). APR provides the user with a guaranteed specification for minimum available frequency deviation over all operating conditions. Operating conditions include operating temperature range, power supply variation, and differences in output loading and changes due to aging. A TRU050 VCXO with an APR of +/-50 ppm will track a +/-50 ppm reference source over all operating conditions. The fourth character of the product code in Table 6 specifies absolute Pull Range (APR). Please see Vectron’s web site, www.vectron.com, for the APR Application Note. APR is tested at 0.5 and 4.5 volts for a 5 volt option and 0.3 and 3.0 volts for the 3.3 volt option. VCXO Aging Quartz stabilized oscillators typically exhibit a small shift in output frequency during aging. The major factors, which lead to this shift, are changes in the mechanical stress on the crystal and mass-loading of foreign material on the crystal. As the oscillator ages, relaxation of the crystal mounting stress or transfer of environmental stress through the package to the crystal mounting arrangement can lead to frequency variations. VI has minimized these two effects through the use of a miniature AT-Cut strip resonator crystal, which allows a superior mounting arrangement, and results in minimal relaxation and almost negligible environmental stress transfer. VI has eliminated the impact of mass loading by ensuring hermetic integrity and minimizing outgassing by limiting the number of internal components through the use of ASIC technology. Mass-loading on the crystal generally results in a frequency decrease and is typically due to outgassing of material within a hermetic package or from contamination by external material in a less than hermetic package. Under normal operating conditions with an operating temperature of 40°C, the TRU050 will typically exhibit 2 ppm aging in the first year of operation. The device will then typically exhibit 1 ppm aging the following year with a logarithmic decline each year thereafter. Divide-By Feature The lowest available VCXO OUT 1 frequency is 12.000MHz. To achieve lower frequencies, such as 1.544 or 2.048 MHz, OUT1 is divided by a 2n counter , where n=1 to 8 and is the OUT2 frequency. This results in a divide by 2,4,8…256 option and is wire-bonded at the factory, so it is user selectable upon ordering only. To achieve 1.544 or 2.048MHz, a TRU050 at 24.704 with a divide by 16 or a TRU050 16.384 with a divide-by 8 would be used. Additional external divide-by circuits can be used to further lower or change the input frequency range. A disabled Out2 is available. Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 6 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Loop Filter A PLL is a feedback system which forces the output frequency to lock in both phase and frequency to the input frequency. While there will be some phase error, theory states there is no frequency error. The loop filter design will dictate many key parameters such as jitter reduction, stability, lock range and acquisition time. Be advised that many textbook equations describing loop dynamics, such as capture range or lockin time, are based on ideal systems. Such equations may not be accurate for real systems due to nonlinearities, DC offsets, noise and don’t take into account the limited VCXO bandwidth. This section deals with some real world design examples. Also, there is loop filter software on the Vectron web site, plus experienced applications engineers are eager to assist in this process. Common TRU050 PLL applications are shown in figures 7 and 8 (frequency translation), 9 (clock recovery) and 10 (clock smoothing). Of primary concern to the designer is selecting a loop filter that insures lock-in, stability and provides adequete filtering of the input signal. A good starting point for the the loop filter bandwidth is 100ppm times the DATAIN frequency. An example would be translating an 8kHz signal to 44. 736MHz – DS3 – which is = 100 ppm x kHz = 8Hz . So for 8kHz inputs, ~ 8 Hz loop bandwidth may be reasonable and figures 7 and 8 show and 8kHz to DS3 and 8kHz to 19.440 MHz frequency translation designs. It’s fairly easy to set a low loop bandwidth for large frequency translations such as 8kHz to 44.736MHz, but becomes more difficult for clock smoothing applications such as 19.440MHz in and 19.440MHz output. In this example, 100ppm x 19.440MHz is about 2kHz and may be too high to reject kow frequency jitter. A good way to resolve this is to lower the input frequency such as dividing the input frequency down. The loop filter bandwidth becomes lower since 100ppm * DATAIN is lowered. Figure 10 shows an example of how to design a low loop bandwith on a relatively high input signal and still maintain a wide lock range. The “100ppm * DATAIN frequency” loop filter bandwidth can then be tailored to the application, since lower bandwidthds are desriable to clean up and or translate clock signals and higher bandwidths may be needed for clock recovery of NRZ signals. There is no known accurate formula for calculating acquisition time and so the best way to provide realisitc figures is to measure the lock time for a TRU050. Aquistion time was measured to be 3 to 5 seconds by measuring the control voltage in an 8kHz to 34.368 MHz frequency translation application - similar to the application in figure 7 and 8, to sub 10 milliseconds for NRZ data patterns such as figure 9. It may be tempting reduce the damping factor to 0.7 or 1.0 in order to increase aquisition time; but, it degrades stability and will not signifigantly decrease lock time. This is due to the fact that most VCXO’s have a 10kHz bandwidth so setting a 100kHz loop bandwidth is impossible. A damping factor of 4 is fairly conservative and allows for excellent stability. Some general quidelines for selecting loop filter include: Values should be less than 1Megohm and at least 10Kohm between the PHO and OPN, the capacitor should be low leakage and a polarized capacitor is acceptable, the R/C’s should be located physically close to the TRU050 . Also, the loop filter software available on the web site was written for 5 volt operation, a simple way to calculate values for 3.3 volt operation is to times the data density by 0.66 (3.3V / 5V). SPICE models are another design aid. In most cases a new PLL TRU050 design is calculated by using the software and verified with SPICE models, and depending on the circumstances evaluated in the applications lab. The simple active pi model is in figure 7. Loop filter values can be modified to suit the system requirements and application. There are many excellent references on designing PLL’s, such as “PhaseLocked Loops, Theory, Design and Applications”, by Roland E Best McGraw-Hill; however, there is loop filter software on the Vectron web site, plus experienced applications engineers eager to assist in this process. Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 7 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Figure 7. SPICE Model Vi Ri 1 E1 R2 C1 2 3 E2 R1 4 C2 5 Rf Cf 6 E3 R5 C4 7 8 E4 9 R6 C5 10 E5 E6 11 R7 12 *****TRU050 ac Loop model vi 1 0 ac 1 ri 1 0 1K *****Phase Detector e1 2 0 1 0 1 (for closed loop response use: e1 2 0 1 12 1) r2 2 3 30K c1 2 0 60p *****Phase Detector Gain=0.53 x Data Density (Data Density=1 for clocks) for 5 volt operation and = 0.35 * Data Density for 3.3 volt operation e2 4 0 3 0 .35 *****Loop filter r1 4 5 60K c2 5 0 10p rf 5 6 90K cf 6 7 1.0u e3 7 0 5 0 –10000 ***** VCXO, Input Bandwidth=50kHz r5 7 8 160K c4 8 0 20p *****VCXO Gain x 2pi (Example, use OUT1 x 100ppm x 2 x pi) e4 9 0 8 0 12214 *****1/S model r6 9 10 1000 c5 10 11 0.001 e5 11 0 10 0 –1e6 ****Divide by N e6 12 0 11 0 1 r8 12 0 1K The bold numbers are user selectable R/C, data density, VCXO frequency and divideby values, and are from figure 11. Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 8 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Layout Considerations To achieve stable, low noise performance good analog layout techniques should be incorporated and a partial list includes: The TRU050 should be treated more like an analog device and the power supply should be well decoupled with good quality RF 0.01 uf and 0.1uf capacitors. In some cases, a pi filter such as a large capacitor (10uF) to ground, a series ferrite bead or inductor, and 0.01 uf and 100 pf capacitor to ground to decouple the device supply is used. The traces for the OUT1, OUT2, RCLK and RDATA ouputs should be kept as short as possible. It is common practice to use a series resistor – 50 to 100 ohms – in order to reduce reflections if these traces are more than a couple of inches long. Also OUT1, OUT2 RCLK and RDATA should not be routed directly underneath the device. The op-amp loop filter components should be kept as close to the device as possible and the feedback capacitor should be located close the op-amp input terminal. The loop filter capacitor(s) should be low leakage and polarized capacitors are allowed keeping this is mind. Unused outputs should be left floating and it is not required to load or terminate them (such as an PECL or ECL output). Loading unused outputs will only increase current consumption. Typical Application Circuits 10K 0.1uF 10K 2.2uF 330K 20K pin 6 pin 2 pin 3 0.1uF pin 1 8 kHz (Pin 7) pin 15 44.736 MHz ∅ TRU050 16kHz (Pin 9) pin 4 10K 10K , 2.2uF ÷ 2796 The above loop has a 11 Hz bandwidth. Figure 8. 8kHz to DS3 Frequency Translation Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 9 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL 20K 0.1uF 20K 2.2uF 600K 20K 0.1uF pin 6 pin 2 pin 3 pin 1 pin 15 8 kHz (Pin 7) 19.440MHz ∅ TRU050 pin 4 16kHz (Pin 9) 10K 10K , 2.2uF ÷ 1215 The above loop has a 10 Hz bandwidth. Figure 9. 8kHz to 19.44MHz Frequency Translation 10K pin 6 0.01uF 130K pin 2 pin 3 pin 1 44.736 Mb/s (Pin 7) Pin 15 44.736 MHz ∅ pin 4 Disabled TRU050 10K (Pin 9) 10K, 2.2uF The above loop has a 4.5 kHz bandwidth. Figure 10. DS3 NRZ Clock Recovery Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 10 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL 60K 19.440MHz 1.0uF 90K pin 6 pin 2 10K pin 3 pin 1 Pin 15 ÷16 ∅ 19.440 MHz Pin 13 Pin 9 2.430 MHz TRU050 pin 4 10K, 2.2uF , 10K The above loop has a 125 Hz bandwidth. Figure 11. 19.440 Clock Smoothing Table 5. Reflow Profile (IPC/JEDEC J-STD-020C) PreHeat Time Ramp Up Time Above 217 oC Time To Peak Temperature Time At 260 oC Ramp Down Symbol Value tS 60 sec Min, 180 sec Max R UP 3 oC/sec Max tL 60 sec Min, 150 sec Max t AMB-P 480 sec Max tP 20 sec Min, 40 sec Max R DN 6 oC/sec Max The device has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements. The temperatures refer to the topside of the package, measured on the package body surface. The TRU050 device is hermetically sealed so an aqueous wash is not an issue. tL 260 R UP Temperature (DegC) Parameter 217 200 tP R DN 150 tS t AMB-P 25 Time (sec) Figure 12. Suggested IR profile Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 11 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Figure 13. Tape and Reel Diagram Table 6. Tape and Reel Information Tape Dimensions (mm) Reel Dimensions (mm) Dimension A B C D E F G H I J K L Tolerance Typ Typ Typ Typ Typ Min Min Typ Min Typ Max Typ # Per Reel TRU050 32 14.2 1.5 4 16 1.78 21 13.0 100 5 33.1 330 200 Package Outline Diagrams Figure 14. “Gull Wing Lead” Package Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 12 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Figure 15. “Thru Hole Lead” Package Table 7. Pin Functions Pin Symbol Function 1 2 3 4 5 VC OPN OPOUT OPP LOSIN 6 7 8 9 10 PHO DATAIN GND CLKIN LOS 11 12 13 14 RCLK RDATA Output 2 HIZ 15 16 Output 1 VDD VCXO Control Voltage Op-Amp Negative Input Op-Amp Output Op-Amp Positive Input INPUT (Used with LOS) Logic 0, VCXO control voltage is enabled. Logic 1, VCXO control voltage (pin 1) is disabled and OUT1 and OUT2 are within +/-75 ppm of center frequency Has Internal pull-down resistor Phase detector output Phase detector Input signal (TTL switching thresholds) Cover and Electrical Ground Phase detector Clock signal (TTL switching thresholds) OUTPUT (Used with LOSIN) Logic 1 if there are no transitions detected at DATAIN after 256 clock cycles at CLKIN. As soon as a transition occurs at DATAIN, LOS is set to logic low. Recovered Clock Recovered Data Divided-down VCXO Output, or No Output INPUT Logic 0, OUT1, OUT2, RCLK, RDATA are set to a high impedance state. Logic 1, OUT1, OUT2, RCLK, RDATA are active. Has Internal pull-up resistor VCXO Output Power Supply Voltage (3.3 V ±10% or 5.0 V ±10%) Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 13 of 14 Rev: 26Aug2008 TRU050, VCXO Based PLL Ordering information Table 8. Standard OUT1 Frequencies 12.0000000 12.2880000 12.6240000 13.8240000 16.0000000 16.1280000 16.3840000 16.7770000 16.8960000 17.9200000 18.4320000 28.0000000 41.2416000 65.5360000 19.4400000 30.7200000 41.9430000 20.0000000 32.0000000 44.7360000 20.4800000 32.7680000 47.4570000 22.1184000 33.3300000 49.1520000 22.5790000 34.3680000 49.4080000 24.5760000 35.3280000 50.0000000 25.0000000 38.8800000 51.8400000 25.2480000 40.0000000 61.4400000 27.0000000 40.9600000 62.2080000 * Other frequencies may be available upon request Table 9. Part Number Builder TRU050 - G A L G A - xxMxxxxxxx Lead Style Frequency (See Above) T: Thru hole 1M00000000 – 65M5360000 G: Gull Wing Divide by Power Supply A=2 A: 5.0V B=4 B: 3.3 V C=8 Absolute Pull Range D=16 G: ±50 E=32 N: ±80 F=64 H: ±100 G=128 Temperature Range H=256 C: 0 to 70 °C K=Disabled L: -40 to 85 °C Contact Information: USA: Vectron International • 267 Lowell Rd. Hudson, NH 03051 Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281 ASIA: 1F-2F, No 8 Workshop, No. 308 Fenju Road, WaiGaoQiao Free Trade Zone, Pudong, Shanghai, China 200131 Tel: 86 21 5048 0777 • Fax: 86 21 5048 1881 Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Revision History Date Approved 26AUG2008 BW Description Part number frequency format revised from xx.xxx MHz to xxMxxxxxxx. Tel: 1-88-VECTRON-1 • Web: www.vectron.com Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 14 of 14 Rev: 26Aug2008