Multilayer ceramic capacitor HighCV, X7R 1206 50 V Series/Type: Chip Ordering code: B37872K5105K0** Date: Version: 25.10.2005 1 Content of inside pages of data sheet. Data will be automatically entered into headers and footers. Please fill in the table and then change the colour to “White”. This ensures that the table disappears for the customer pdf. Identification/Classification 1: (header 1) Multilayer ceramic capacitor Identification/Classification 2: (header 2) HighCV, X7R 1206 50 V Ordering code: B37872K5105K0** Series/Type: Chip Preliminary data (optional): (if necessary) Department: KB VS PE Date: 25.10.2005 Prepared by: Release signed PE: Release signed QS: Modifications/Remarks: Mr. Huainig Dr. Engel Dr. Slakhorst xx xx xx © EPCOS AG 2005. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Multilayer ceramic capacitor HighCV, X7R 1206 50 V B37872K5105K0** Chip Ordering code B37872 K 5 105 K 0 62 Type and size: 872 = X7R/1206 Metallization type: K = Ag/Ni/Sn Rated voltage: 0 = 50 V Rated capacitance (example): 105 = 10 · 105 pF (1 µF) Capacitance tolerance: K = ±10% Internal code Packaging code: 62 = Blister, 180-mm reel 72 = Blister, 330-mm reel Dimensional drawing Size [inch / mm] 1206 / 3216 l [mm] 3.2 ±0.20 b [mm] 1.6 ±0.15 s [mm] 1.2 ±0.10 k [mm] 0.25 – 0.75 see also “Ordering codes and chip thickness”, dimensions in accordance to CECC 32101-801 KB VS PE Please read Cautions and Warnings and Important notes at the end of this document. 25.10.2005 Page 2 of 5 Multilayer ceramic capacitor HighCV, X7R 1206 50 V B37872K5105K0** Chip Electrical data Temperature characteristic: Climatic category (IEC 60068-1): Standard: Dielectric: Rated voltage: Capacitance1) test conditions Test frequency: Test voltage: Max. relative capacitance change: Dissipation factor tanδ (limit value): X7R 55/125/56 EIA Class 2 50 V Time constant τ at +25 °C: Operating temperature range: Capacitance value: > 500 s –55 °C ... +125 °C 1 µF 1) (1.0 ±0.2) kHz (1.0 ±0.2) VRMS ±15% < 25 · 10-3 Subject to aging, please see “General Technical Information” at www.epcos.com/ceramic_capacitors or the databook “Multilayer Ceramic Capacitors”. Ordering codes and chip thickness Size CR [inch] [µF] 1206 1 Ordering code Thickness [mm] B37872K5105K062* * Ordering Code Example 1.2 ±0.1 Packing quantity ∅ 180-mm reel [pcs] 3000 Standard tolerance: ± 10% Standard packaging: Blister tape, 180-mm reel KB VS PE Please read Cautions and Warnings and Important notes at the end of this document. ∅ 330-mm reel [pcs] 12000 25.10.2005 Page 3 of 5 Multilayer ceramic capacitor HighCV, X7R 1206 50 V B37872K5105K0** Chip Further information Please see General Technical Information at www.epcos.com/ceramic_capacitors or the data book “Multilayer Ceramic Capacitors” for further information on: Soldering directions Taping and packing Surface mounting instructions Effects of mechanical stress Cautions and warnings Derating: A “state of the art” application design is essential to achieve failures rates at ppb level. Do not use designs based on 100% of specified rated values. AC applications may damage MLCC on a much lower level than DC voltage due to power dissipation losses. Mechanical stress - Please note EPCOS “General Technical Information”, “Surface mounting instructions” and information about the effect of mechanical stress. ESD - EPCOS recommends the use of varistors. Further processing - care must be taken using moulding processes. Combined stresses - the total stress (e.g. DC voltage, AC ripple, pulses and temperature) has to be taken into account to estimate reliability of MLCC. KB VS PE Please read Cautions and Warnings and Important notes at the end of this document. 25.10.2005 Page 4 of 5 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, CeraDiode, CSSP, PhaseCap, PhaseMod, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, TOPcap, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 5 of 5