FREESCALE 56853

56853
Data Sheet
Technical Data
56800E
16-bit Digital Signal Controllers
DSP56853
Rev. 6
01/2007
freescale.com
56853 General Description
• 120 MIPS at 120MHz
• Serial Port Interface (SPI)
• 12K x 16-bit Program SRAM
• 8-bit Parallel Host Interface
• 4K x 16-bit Data SRAM
• General Purpose 16-bit Quad Timer
• 1K x 16-bit Boot ROM
• JTAG/Enhanced On-Chip Emulation (OnCE™) for
unobtrusive, real-time debugging
• Access up to 2M words of program memory or 8M of
data memory
• Computer Operating Properly (COP)/Watchdog Timer
• Chip Select Logic for glue-less interface to ROM and
SRAM
• Time-of-Day (TOD)
• Six (6) independent channels of DMA
• Up to 41 GPIO
• 128 LQFP package
• Enhanced Synchronous Serial Interfaces (ESSI)
• Two (2) Serial Communication Interfaces (SCI)
6
VDDIO
VDD
11
6
VSSIO
10
JTAG/
Enhanced
OnCE
Program Controller
and
Hardware Looping Unit
VSS VDDA
VSSA
6
16-Bit
56800E Core
Address
Generation Unit
Data ALU
16 x 16 + 36 → 36-Bit MAC
Three 16-bit Input Registers
Four 36-bit Accumulators
Bit
Manipulation
Unit
PAB
PDB
CDBR
CDBW
Data Memory
4,096 x 16 SRAM
XAB1
XAB2
System Bus
Control
PAB
DMA
6 channel
PDB
CDBR
CDBW
Decoding
Peripherals
IPRDB
IPAB
IPWDB
IPBus Bridge (IPBB)
A0-20 [20:0]
IPBus CLK
External Data
Bus Switch
RD Enable
WR Enable
CS0-CS3[3:0] or
GPIOA0-A3[3:0]
Bus Control
POR
External Bus
Interface Unit
2 SCI
or
GPIOE
4
ESSI0
or
GPIOC
6
Quad
Timer
or
GPIOG
4
SPI
Host
Interrupt
or
Interface Controller
GPIOF
or
GPIOB
4
16
COP/
Watchdog
Time
of
Day
CLKO
3
System
COP/TOD CLK Integration
Module
External Address
Bus Switch
D0-D15 [15:0]
Core CLK
Boot ROM
1024 x 16 ROM
XDB2
DMA Requests
Memory
Program Memory
12,288 x 16 SRAM
Clock
Generator
MODEA-C or
(GPIOH0-H2)
RSTO
RESET
EXTAL
XTAL
OSC PLL
IRQA
IRQB
56853 Block Diagram
56853 Technical Data, Rev. 6
Freescale Semiconductor
3
Part 1 Overview
1.1 56853 Features
1.1.1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.1.2
•
•
Core
Efficient 16-bit engine with dual Harvard architecture
120 Million Instructions Per Second (MIPS) at 120MHz core frequency
Single-cycle 16 × 16-bit parallel Multiplier-Accumulator (MAC)
Four (4) 36-bit accumulators including extension bits
16-bit bidirectional shifter
Parallel instruction set with unique DSP addressing modes
Hardware DO and REP loops
Three (3) internal address buses and one (1) external address bus
Four (4) internal data buses and one (1) external data bus
Instruction set supports both DSP and controller functions
Four (4) hardware interrupt levels
Five (5) software interrupt levels
Controller-style addressing modes and instructions for compact code
Efficient C Compiler and local variable support
Software subroutine and interrupt stack with depth limited only by memory
JTAG/Enhanced OnCE debug programming interface
Memory
Harvard architecture permits up to three (3) simultaneous accesses to program and data memory
On-Chip Memory
— 12K × 16-bit Program SRAM
— 4K × 16-bit Data SRAM
— 1K × 16-bit Boot ROM
•
Off-Chip Memory Expansion (EMI)
— Access up to 2M words of program memory or 8M data memory
— Chip Select Logic for glue-less interface to ROM and SRAM
1.1.3
•
•
•
•
•
Peripheral Circuits for 56853
General Purpose 16-bit Quad Timer*
Two (2) Serial Communication Interfaces (SCI)*
Serial Peripheral Interface (SPI) Port*
Enhanced Synchronous Serial Interface (ESSI) modules*
Computer Operating Properly (COP)
56853 Technical Data, Rev. 6
4
Freescale Semiconductor
56853 Description
•
•
•
•
•
•
•
Watchdog Timer
JTAG/Enhanced On-Chip Emulation (OnCE) for unobtrusive, real-time debugging
Six (6) independent channels of DMA
8-bit Parallel Host Interface*
Time-of-Day (TOD)
128 LQFP package
Up to 41 GPIO
* Each peripheral I/O can be used alternately as a General Purpose I/O if not needed
1.1.4
•
•
Energy Information
Fabricated in high-density CMOS with 3.3V, TTL-compatible digital inputs
Wait and Stop modes available
1.2 56853 Description
The 56853 is a member of the 56800E core-based family of controllers. It combines, on a single chip, the
processing power of a Digital Signal Processor (DSP) and the functionality of a microcontroller with a
flexible set of peripherals to create an extremely cost-effective solution. Because of its low cost,
configuration flexibility, and compact program code, the 56853 is well-suited for many applications. The
56853 includes many peripherals that are especially useful for low-end Internet appliance applications
and low-end client applications such as telephony; portable devices; Internet audio and point-of-sale
systems, such as noise suppression; ID tag readers; sonic/subsonic detectors; security access devices;
remote metering; sonic alarms.
The 56800E core is based on a Harvard-style architecture consisting of three execution units operating in
parallel, allowing as many as six operations per instruction cycle. The microprocessor-style programming
model and optimized instruction set allow straightforward generation of efficient, compact DSP and
control code. The instruction set is also highly efficient for C Compilers, enabling rapid development of
optimized control applications.
The 56853 supports program execution from either internal or external memories. Two data operands can
be accessed from the on-chip Data RAM per instruction cycle. The 56853 also provides two external
dedicated interrupt lines, and up to 41 General Purpose Input/Output (GPIO) lines, depending on
peripheral configuration.
The 56853 controller includes 12K words of Program RAM, 4K words of Data RAM, and 1K words of
Boot ROM. It also supports program execution from external memory. The 56800 core can access two data
operands from the on-chip Data RAM per instruction cycle.
This controller also provides a full set of standard programmable peripherals that include an 8-bit parallel
Host Interface, Enhanced Synchronous Serial Interface (ESSI), one Serial Peripheral Interface (SPI), the
option to select a second SPI or two Serial Communications Interfaces (SCIs), and Quad Timer. The Host
Interface, ESSI, SPI, SCI, four chip selects and quad timer can be used as General Purpose Input/Outputs
(GPIOs) if its primary function is not required.
56853 Technical Data, Rev. 6
Freescale Semiconductor
5
1.3 State of the Art Development Environment
•
•
Processor ExpertTM (PE) provides a Rapid Application Design (RAD) tool that combines easy-to-use
component-based software application creation with an expert knowledge system.
The Code Warrior Integrated Development Environment is a sophisticated tool for code navigation,
compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards
will support concurrent engineering. Together, PE, Code Warrior and EVMs create a complete, scalable
tools solution for easy, fast, and efficient development.
1.4 Product Documentation
The four documents listed in Table 1-1 are required for a complete description of and proper design with
the 56853. Documentation is available from local Freescale distributors, Freescale Semiconductor sales
offices, Freescale Literature Distribution Centers, or online at www.freescale.com.
Table 1-1 56853 Chip Documentation
Topic
Description
Order Number
DSP56800E
Reference Manual
Detailed description of the 56800E architecture, 16-bit
controller core processor and the instruction set
DSP56800ERM
DSP56853
User’s Manual
Detailed description of memory, peripherals, and
interfaces of the 56853
DSP5685xUM
DSP56853
Technical Data Sheet
Electrical and timing specifications, pin descriptions,
and package descriptions
DSP56853
DSP56853
Errata
Details any chip issues that might be present
DSP56853E
56853 Technical Data, Rev. 6
6
Freescale Semiconductor
Data Sheet Conventions
1.5 Data Sheet Conventions
This data sheet uses the following conventions:
OVERBAR
This is used to indicate a signal that is active when pulled low. For example, the RESET pin is
active when low.
“asserted”
A high true (active high) signal is high or a low true (active low) signal is low.
“deasserted”
A high true (active high) signal is low or a low true (active low) signal is high.
Examples:
Signal/Symbol
Logic State
Signal State
Voltage1
PIN
True
Asserted
VIL/VOL
PIN
False
Deasserted
VIH/VOH
PIN
True
Asserted
VIH/VOH
PIN
False
Deasserted
VIL/VOL
1. Values for VIL, VOL, VIH, and VOH are defined by individual product specifications.
56853 Technical Data, Rev. 6
Freescale Semiconductor
7
Part 2 Signal/Connection Descriptions
2.1 Introduction
The input and output signals of the 56853 are organized into functional groups, as shown in Table 2-1 and
as illustrated in Figure 2-1. In Table 3-1 each table row describes the package pin and the signal or signals
present.
Table 2-1 56853 Functional Group Pin Allocations
Functional Group
Number of Pins
Power (VDD, VDDIO, or VDDA)
(6, 11, 1)1
Ground (VSS, VSSIO,or VSSA)
(6, 10, 1)1
PLL and Clock
3
External Bus Signals
39
External Chip Select*
4
Interrupt and Program Control
72
Host Interface (HI)*
163
Enhanced Synchronous Serial Interface (ESSI0) Port*
6
Serial Communications Interface (SCI0) Ports*
2
Serial Communications Interface (SCI1) Ports*
2
Serial Peripheral Interface (SPI) Port*
4
Quad Timer Module Port*
4
JTAG/Enhanced On-Chip Emulation (EOnCE)
6
*Alternately, GPIO pins
1. VDD = VDD CORE, VSS = VSS CORE, VDDIO= VDD IO, VSSIO = VSS IO, VDDA = VDD ANA, VSSA = VSS ANA
2. MODA, MODB and MODC can be used as GPIO after the bootstrap process has completed.
3. The following Host Interface signals are multiplexed: HRWB to HRD, HDS to HWR, HREQ to HTRQ and HACK to HRRQ.
56853 Technical Data, Rev. 6
8
Freescale Semiconductor
Introduction
VDD
Logic
Power
1
6
VSS
1
6
1
VDDIO
I/O
Power
1
11
VSSIO
10
1
Analog
Power1
VDDA
1
1
VSSA
1
1
1
1
56853
A0 - A20
21
D0 - D15
External
Bus
TXD1 (GPIOE3)
SCI 2
STD0 (GPIOC0)
SRD0 (GPIOC1)
SCK0 (GPIOC2)
SC00 (GPIOC3)
ESSI 0
SC01 (GPIOC4)
SC02 (GPIOC5)
4
8
HA0 - HA2 (GPIOB8 - B10)
3
HRWB (HRD) (GPIOB11)
1
HDS (HWR) (GPIOB12)
1
HCS (GPIOB13)
1
HREQ (HTRQ) (GPIOB14)
1
1
1
1
MISO (GPIOF0)
MOSI (GPIOF1)
SCK (GPIOF2)
SPI
SS (GPIOF3)
1
HACK (HRRQ) (GPIOB15)
1
1
1
TIO0 - TIO3 (GPIOG0 - G3)
4
IRQA
IRQB
MODA, MODB, MODC
(GPIOH0 - H2)
Interrupt /
Program
Control
RXD1 (GPIOE2)
1
HD0 - HD7 (GPIOB0 - B7)
Timer
Module
SCI 0
1
CS0 - CS3 (GPIOA0 - A3)
Host
Interface
TXDO (GPIOE1)
16
RD
WR
Chip
Select
1
RXDO (GPIOE0)
1
1
1
1
1
1
RESET
RSTO
3
1
1
1
1
1
XTAL
EXTAL
CLKO
PLL /
Clock
TCK
TDI
TDO
TMS
JTAG /
Enhanced
OnCE
TRST
DE
Figure 2-1 56853 Signals Identified by Functional Group2
1. Specifically for PLL, OSC, and POR.
2. Alternate pin functions are shown in parentheses.
56853 Technical Data, Rev. 6
Freescale Semiconductor
9
Part 3 Signals and Package Information
All digital inputs have a weak internal pull-up circuit associated with them. These pull-up circuits are
enabled by default. Exceptions:
1. When a pin has GPIO functionality, the pull-up may be disabled under software control.
2. MODE A, MODE B and MODE C pins have no pull-up.
3. TCK has a weak pull-down circuit always active.
4. Bidirectional I/O pullups automatically disable when the output is enabled.
This table is presented consistently with the Signals Identified by Functional Group figure.
1. BOLD entries in the Type column represents the state of the pin just out of reset.
2. Output(Z) means an output in a High-Z condition
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP
Pin No.
Signal Name
Type
Description
13
VDD
VDD
47
VDD
Power (VDD)—These pins provide power to the internal structures of
the chip, and should all be attached to VDD.
64
VDD
79
VDD
80
VDD
112
VDD
14
VSS
VSS
48
VSS
Ground (VSS)—These pins provide grounding for the internal
structures of the chip and should all be attached to VSS.
63
VSS
81
VSS
96
VSS
113
VSS
56853 Technical Data, Rev. 6
10
Freescale Semiconductor
Introduction
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
5
VDDIO
VDDIO
18
VDDIO
Power (VDDIO)—These pins provide power for all I/O and ESD
structures of the chip, and should all be attached to VDDIO (3.3V).
41
VDDIO
55
VDDIO
61
VDDIO
72
VDDIO
91
VDDIO
92
VDDIO
100
VDDIO
114
VDDIO
124
VDDIO
6
VSSIO
VSSIO
19
VSSIO
Ground (VSSIO)—These pins provide grounding for all I/O and ESD
structures of the chip and should all be attached to VSS.
42
VSSIO
56
VSSIO
62
VSSIO
74
VSSIO
93
VSSIO
102
VSSIO
115
VSSIO
125
VSSIO
22
VDDA
VDDA
Analog Power (VDDA)—These pins supply an analog power source.
23
VSSA
VSSA
Analog Ground (VSSA)—This pin supplies an analog ground.
56853 Technical Data, Rev. 6
Freescale Semiconductor
11
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
9
A0
Output(Z)
10
A1
11
A2
12
A3
26
A4
27
A5
28
A6
29
A7
43
A8
44
A9
45
A10
46
A11
57
A12
58
A13
59
A14
60
A15
67
A16
68
A17
69
A18
70
A19
71
A20
Address Bus (A0-A20)—These signals specify a word address for
external program or data memory access.
56853 Technical Data, Rev. 6
12
Freescale Semiconductor
Introduction
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
73
D0
Input/Output(Z)
86
D1
87
D2
88
D3
89
D4
90
D5
107
D6
108
D7
109
D8
110
D9
111
D10
122
D11
123
D12
126
D13
127
D14
128
D15
7
RD
Output
Data Bus (D0-D15)—These pins provide the bidirectional data for
external program or data memory accesses.
Read Enable (RD) —is asserted during external memory read cycles.
This signal is pulled high during reset.
8
WR
Output
Write Enable (WR)— is asserted during external memory write
cycles.
This signal is pulled high during reset.
75
76
77
78
CS0
Output
External Chip Select (CS0)—This pin is used as a dedicated GPIO.
GPIOA0
Input/Output
Port A GPIO (0) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
CS1
Output
External Chip Select (CS1)—This pin is used as a dedicated GPIO.
GPIOA1
Input/Output
Port A GPIO (1) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
CS2
Output
External Chip Select (CS2)—This pin is used as a dedicated GPIO.
GPIOA2
Input/Output
Port A GPIO (2) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
CS3
Output
External Chip Select (CS3)—This pin is used as a dedicated GPIO.
GPIOA3
Input/Output
Port A GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
56853 Technical Data, Rev. 6
Freescale Semiconductor
13
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
30
HD0
Input
Host Address (HD0)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
31
GPIOB0
Input/Output
HD1
Input
Port B GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD1)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
32
GPIOB1
Input/Output
HD2
Input
Port B GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD2)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
36
GPIOB2
Input/Output
HD3
Input
Port B GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD3)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
37
GPIOB3
Input/Output
HD4
Input
Port B GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD4)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
38
GPIOB4
Input/Output
HD5
Input
Port B GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD5)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB5
Input/Output
Port B GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
56853 Technical Data, Rev. 6
14
Freescale Semiconductor
Introduction
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
39
HD6
Input
Host Address (HD6)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
40
GPIOB6
Input/Output
HD7
Input
Port B GPIO (6)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD7)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
82
GPIOB7
Input/Output
Port B GPIO (7)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
HA0
Input
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
83
GPIOB8
Input/Output
Port B GPIO (8)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
HA1
Input
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
84
GPIOB9
Input/Output
Port B GPIO (9)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
HA2
Input
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
85
GPIOB10
Input/Output
HRWB
Input
Port B GPIO (10)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
Host Read/Write (HRWB)—When the HI08 is programmed to
interface to a single-data-strobe host bus and the HI function is
selected, this signal is the Read/Write input.
These pins are disconnected internally.
HRD
Input
Host Read Data (HRD)—This signal is the Read Data input when the
HI08 is programmed to interface to a double-data-strobe host bus and
the HI function is selected.
GPIOB11
Input/Output
Port B GPIO (11)—This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
56853 Technical Data, Rev. 6
Freescale Semiconductor
15
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
103
HDS
Input
Host Data Strobe (HDS)—When the HI08 is programmed to
interface to a single-data-strobe host bus and the HI function is
selected, this input enables a data transfer on the HI when HCS is
asserted.
These pins are disconnected internally.
104
HWR
Input
Host Write Enable (HWR)—This signal is the Write Data input when
the HI08 is programmed to interface to a double-data-strobe host bus
and the HI function is selected.
GPIOB12
Input/Output
HCS
Input
Port B GPIO (12)—This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
Host Chip Select (HCS)—This input is the chip select input for the
Host Interface.
These pins are disconnected internally.
105
GPIOB13
Input/Output
Port B GPIO (13)—This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
HREQ
Open Drain
Output
Host Request (HREQ)—When the HI08 is programmed for HRMS=0
functionality (typically used on a single-data-strobe bus), this open
drain output is used by the HI to request service from the host
processor. The HREQ may be connected to an interrupt request pin
of a host processor, a transfer request of a DMA controller, or a
control input of external circuitry.
These pins are disconnected internally.
HTRQ
Open Drain
Output
Transmit Host Request (HTRQ)—This signal is the Transmit Host
Request output when the HI08 is programmed for HRMS=1
functionality and is typically used on a double-data-strobe bus.
GPIOB14
Input/Output
Port B GPIO (14)—This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
56853 Technical Data, Rev. 6
16
Freescale Semiconductor
Introduction
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
106
HACK
Input
Host Acknowledge (HACK)—When the HI08 is programmed for
HRMS=0 functionality (typically used on a single-data-strobe bus),
this input has two functions: (1) provide a Host Acknowledge signal
for DMA transfers or (2) to control handshaking and provide a Host
Interrupt Acknowledge compatible with the MC68000 family
processors.
These pins are disconnected internally.
HRRQ
Open Drain
Output
Receive Host Request (HRRQ)—This signal is the Receive Host
Request output when the HI08 is programmed for HRMS=1
functionality and is typically used on a double-data-strobe bus.
GPIOB15
Input/Output
Port B GPIO(15)—This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
TIO0
Input/Output
Timer Input/Outputs (TIO0)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG0
Input/Output
Port G GPIOG0—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
TIO1
Input/Output
Timer Input/Outputs (TIO1)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG1
Input/Output
Port G GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
TIO2
Input/Output
Timer Input/Outputs (TIO2)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG2
Input/Output
Port G GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
TIO3
Input/Output
Timer Input/Outputs (TIO3)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG3
Input/Output
Port G GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
20
IRQA
Input
21
IRQB
External Interrupt Request A and B—The IRQA and IRQB inputs
are asynchronous external interrupt requests that indicate that an
external device is requesting service. A Schmitt trigger input is used
for noise immunity. They can be programmed to be level-sensitive or
negative-edge- triggered. If level-sensitive triggering is selected, an
external pull-up resistor is required for Wired-OR operation.
15
MODA
Input
Mode Select (MODA)—During the bootstrap process MODA selects
one of the eight bootstrap modes.
GPIOH0
Input/Output
Port H GPIO (0)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
101
99
98
97
56853 Technical Data, Rev. 6
Freescale Semiconductor
17
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
16
MODB
Input
Mode Select (MODB)—During the bootstrap process MODB selects
one of the eight bootstrap modes.
GPIOH1
Input/Output
Port H GPIO (1)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
MODC
Input
Mode Select (MODC)—During the bootstrap process MODC selects
one of the eight bootstrap modes.
GPIOH2
Input/Output
Port H GPIO (2)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
RESET
Input
Reset (RESET)—This input is a direct hardware reset on the
processor. When RESET is asserted low, the device is initialized and
placed in the Reset state. A Schmitt trigger input is used for noise
immunity. When the RESET pin is deasserted, the initial chip
operating mode is latched from the MODA, MODB, and MODC pins.
17
35
To ensure complete hardware reset, RESET and TRST should be
asserted together. The only exception occurs in a debugging
environment when a hardware reset is required and it is necessary
not to reset the JTAG/Enhanced OnCE module. In this case, assert
RESET, but do not assert TRST.
34
RSTO
Output
Reset Output (RSTO)—This output is asserted on any reset
condition (external reset, low voltage, software or COP).
65
RXD0
Input
Serial Receive Data 0 (RXD0)—This input receives byte-oriented
serial data and transfers it to the SCI 0 receive shift register.
GPIOE0
Input/Output
Port E GPIO (0)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
TXD0
Output(Z)
Serial Transmit Data 0 (TXD0)—This signal transmits data from the
SCI 0 transmit data register.
GPIOE1
Input/Output
Port E GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
RXD1
Input
GPIOE2
Input/Output
Port E GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
TXD1
Output(Z)
Serial Transmit Data 1 (TXD1)—This signal transmits data from the
SCI 1 transmit data register.
GPIOE3
Input/Output
Port E GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
66
94
95
Serial Receive Data 1 (RXD1)—This input receives byte-oriented
serial data and transfers it to the SCI 1 receive shift register.
56853 Technical Data, Rev. 6
18
Freescale Semiconductor
Introduction
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
116
STD0
Output
GPIOC0
Input/Output
Port C GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
SRD0
Input
ESSI Receive Data (SRD0)—This input pin receives serial data and
transfers the data to the ESSI Receive Shift Register.
GPIOC1
Input/Output
Port C GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
SCK0
Input/Output
ESSI Serial Clock (SCK0)—This bidirectional pin provides the serial
bit rate clock for the transmit section of the ESSI. The clock signal can
be continuous or gated and can be used by both the transmitter and
receiver in synchronous mode.
GPIOC2
Input/Output
Port C GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
SC00
Input/Output
ESSI Serial Control Pin 0 (SC00)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin will be used for the receive
clock I/O. For synchronous mode, this pin is used either for
transmitter1 output or for serial I/O flag 0.
GPIOC3
Input/Output
Port C GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
SC01
Input/Output
ESSI Serial Control Pin 1 (SC01)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin is the receiver frame sync
I/O. For synchronous mode, this pin is used either for transmitter2
output or for serial I/O flag 1.
GPIOC4
Input/Output
Port C GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
SC02
Input/Output
ESSI Serial Control Pin 2 (SC02)—This pin is used for frame sync
I/O. SC02 is the frame sync for both the transmitter and receiver in
synchronous mode and for the transmitter only in asynchronous
mode. When configured as an output, this pin is the internally
generated frame sync signal. When configured as an input, this pin
receives an external frame sync signal for the transmitter (and the
receiver in synchronous operation).
GPIOC5
Input /Output
Port C GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
117
118
119
120
121
Description
ESSI Transmit Data (STD0)—This output pin transmits serial data
from the ESSI Transmitter Shift Register.
56853 Technical Data, Rev. 6
Freescale Semiconductor
19
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
1
MISO
Input/Output
SPI Master In/Slave Out (MISO)—This serial data pin is an input to a
master device and an output from a slave device. The MISO line of a
slave device is placed in the high-impedance state if the slave device
is not selected. The driver on this pin can be configured as an
open-drain driver by the SPI’s Wired-OR mode (WOM) bit when this
pin is configured for SPI operation.
GPIOF0
Input/Output
Port F GPIO (0)—This pin is a General Purpose I/O (GPIO) pin that
can be individually programmed as input or output pin.
MOSI
Input/Output (Z)
SPI Master Out/Slave In (MOSI)—This serial data pin is an output
from a master device and an input to a slave device. The master
device places data on the MOSI line a half-cycle before the clock
edge that the slave device uses to latch the data. The driver on this
pin can be configured as an open-drain driver by the SPI’s WOM bit
when this pin is configured for SPI operation.
GPIOF1
Input/Output
Port F GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
SCK
Input/Output
SPI Serial Clock (SCK)—This bidirectional pin provides a serial bit
rate clock for the SPI. This gated clock signal is an input to a slave
device and is generated as an output by a master device. Slave
devices ignore the SCK signal unless the SS pin is active low. In both
master and slave SPI devices, data is shifted on one edge of the SCK
signal and is sampled on the opposite edge, where data is stable. The
driver on this pin can be configured as an open-drain driver by the
SPI’s WOM bit when this pin is configured for SPI operation. When
using Wired-OR mode, the user must provide an external pull-up
device.
GPIOF2
Input/Output
Port F GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can be individually programmed as input or output pin.
SS
Input
SPI Slave Select (SS)—This input pin selects a slave device before a
master device can exchange data with the slave device. SS must be
low before data transactions and must stay low for the duration of the
transaction. The SS line of the master must be held high.
GPIOF3
Input/Output
Port F GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
24
XTAL
Input/Output
Crystal Oscillator Output (XTAL)—This output connects the internal
crystal oscillator output to an external crystal. If an external clock
source other than a crystal oscillator is used, XTAL must be used as
the input.
25
EXTAL
Input
External Crystal Oscillator Input (EXTAL)—This input should be
connected to an external crystal. If an external clock source other
than a crystal oscillator is used, EXTAL must be tied off. See Section
4.5.2
33
CLKO
Output
2
3
4
Clock Output (CLKO)—This pin outputs a buffered clock signal.
When enabled, this signal is the system clock divided by four.
56853 Technical Data, Rev. 6
20
Freescale Semiconductor
Introduction
Table 3-1. 56853 Signal and Package Information for the 128-pin LQFP (Continued)
Pin No.
Signal Name
Type
Description
54
TCK
Input
Test Clock Input (TCK)—This input pin provides a gated clock to
synchronize the test logic and to shift serial data to the
JTAG/Enhanced OnCE port. The pin is connected internally to a
pull-down resistor.
52
TDI
Input
Test Data Input (TDI)—This input pin provides a serial input data
stream to the JTAG/Enhanced OnCE port. It is sampled on the rising
edge of TCK and has an on-chip pull-up resistor.
51
TDO
Output (Z)
Test Data Output (TDO)—This tri-statable output pin provides a
serial output data stream from the JTAG/Enhanced OnCE port. It is
driven in the Shift-IR and Shift-DR controller states, and changes on
the falling edge of TCK.
53
TMS
Input
Test Mode Select Input (TMS)—This input pin is used to sequence
the JTAG TAP controller’s state machine. It is sampled on the rising
edge of TCK and has an on-chip pull-up resistor.
Note:
50
TRST
Input
Always tie the TMS pin to VDD through a 2.2K resistor.
Test Reset (TRST)—As an input, a low signal on this pin provides a
reset signal to the JTAG TAP controller. To ensure complete
hardware reset, TRST should be asserted whenever RESET is
asserted. The only exception occurs in a debugging environment,
since the Enhanced OnCE/JTAG module is under the control of the
debugger. In this case it is not necessary to assert TRST when
asserting RESET. Outside of a debugging environment RESET
should be permanently asserted by grounding the signal, thus
disabling the Enhanced OnCE/JTAG module on the controller.
Note: For normal operation, connect TRST directly to VSS. If the design
is to be used in a debugging environment, TRST may be tied to VSS through
a 1K resistor.
49
DE
Input/Output
Debug Event (DE)—This is an open-drain, bidirectional, active low
signal. As an input, it is a means of entering debug mode of operation
from an external command controller. As an output, it is a means of
acknowledging that the chip has entered debug mode.
This pin is connected internally to a weak pull-up resistor.
56853 Technical Data, Rev. 6
Freescale Semiconductor
21
Part 4 Specifications
4.1 General Characteristics
The 56853 is fabricated in high-density CMOS with 5-volt tolerant TTL-compatible digital inputs. The
term “5-volt tolerant” refers to the capability of an I/O pin, built on a 3.3V compatible process
technology, to withstand a voltage up to 5.5V without damaging the device. Many systems have a
mixture of devices designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V
and 5V- compatible I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of
3.3V ± 10% during normal operation without causing damage). This 5V tolerant capability therefore
offers the power savings of 3.3V I/O levels while being able to receive 5V levels without being damaged.
Absolute maximum ratings given in Table 4-1 are stress ratings only, and functional operation at the
maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent
damage to the device.
The 56853 DC/AC electrical specifications are preliminary and are from design simulations. These
specifications may not be fully tested or guaranteed at this early stage of the product life cycle. Finalized
specifications will be published after complete characterization and device qualifications have been
completed.
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or
electrical fields. However, normal precautions are
advised to avoid application of any voltages higher
than maximum rated voltages to this high-impedance
circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate voltage level.
56853 Technical Data, Rev. 6
22
Freescale Semiconductor
General Characteristics
Table 4-1 Absolute Maximum Ratings
Characteristic
Supply voltage, core
Supply voltage, IO
Supply voltage, analog
Symbol
Min
Max
Unit
VDD1
VSS – 0.3
VSS + 2.0
V
VDDIO2
VSSIO – 0.3
VSSA – 0.3
VSSIO + 4.0
VDDA + 4.0
V
VIN
VINA
VSSIO – 0.3
VSSA – 0.3
VSSIO + 5.5
VDDA + 0.3
V
I
—
8
mA
TJ
-40
120
°C
TSTG
-55
150
°C
VDDIO
Digital input voltages
Analog input voltages (XTAL, EXTAL)
Current drain per pin excluding VDD, GND
Junction temperature
Storage temperature range
2
1. VDD must not exceed VDDIO
2. VDDIO and VDDA must not differ by more that 0.5V
Table 4-2 Recommended Operating Conditions
Characteristic
Symbol
Min
Max
Unit
VDD
1.62
1.98
V
Supply voltage for I/O Power
VDDIO
3.0
3.6
V
Supply voltage for Analog Power
VDDA
3.0
3.6
V
Ambient operating temperature
TA
-40
85
°C
PLL clock frequency1
fpll
—
240
MHz
Operating Frequency2
fop
—
120
MHz
Frequency of peripheral bus
fipb
—
60
MHz
Frequency of external clock
fclk
—
240
MHz
Frequency of oscillator
fosc
2
4
MHz
Frequency of clock via XTAL
fxtal
—
240
MHz
Frequency of clock via EXTAL
fextal
2
4
MHz
Supply voltage for Logic Power
1.Assumes clock source is direct clock to EXTAL or crystal oscillator running 2-4MHz. PLL must be enabled, locked, and
selected. The actual frequency depends on the source clock frequency and programming of the CGM module.
56853 Technical Data, Rev. 6
Freescale Semiconductor
23
2.Master clock is derived from on of the following four sources:
fclk = fxtal when the source clock is the direct clock to EXTAL
fclk = fpll when PLL is selected
fclk = fosc when the source clock is the crystal oscillator and PLL is not selected
fclk = fextal when the source clock is the direct clock to EXTAL and PLL is not selected
Table 4-3 Thermal Characteristics1
128-pin LQFP
Characteristic
Symbol
Value
Unit
Thermal resistance junction-to-ambient
(estimated)
θJA
43.1
°C/W
I/O pin power dissipation
PI/O
User Determined
W
Power dissipation
PD
PD = (IDD × VDD) + PI/O
W
PDMAX
(TJ – TA) / RθJA2
W
Maximum allowed PD
1. See Section 6.1 for more detail.
2. TJ = Junction Temperature
TA = Ambient Temperature
4.2 DC Electrical Characteristics
Table 4-4 DC Electrical Characteristics
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
Input high voltage (XTAL/EXTAL)
VIHC
VDDA – 0.8
VDDA
VDDA + 0.3
V
Input low voltage (XTAL/EXTAL)
VILC
-0.3
—
0.5
V
Input high voltage
VIH
2.0
—
5.5
V
Input low voltage
VIL
-0.3
—
0.8
V
Input current low (pullups disabled)
IIL
-1
—
1
μA
Input current high (pullups disabled)
IIH
-1
—
1
μA
Output tri-state current low
IOZL
-10
—
10
μA
Output tri-state current high
IOZH
-10
—
10
μA
Output High Voltage
VOH
VDDIO – 0.7
—
—
V
Output Low Voltage
VOL
—
—
0.4
V
Output High Current
IOH
8
—
16
mA
56853 Technical Data, Rev. 6
24
Freescale Semiconductor
DC Electrical Characteristics
Table 4-4 DC Electrical Characteristics (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
Output Low Current
IOL
8
—
16
mA
Input capacitance
CIN
—
8
—
pF
Output capacitance
COUT
—
12
—
pF
VDD supply current (Core logic, memories, peripherals)
IDD4
—
—
—
70
0.05
5
110
10
14
mA
mA
mA
—
40
0
50
1.5
mA
mA
—
60
120
μA
1
Run
Deep Stop2
Light Stop3
VDDIO supply current (I/O circuity)
IDDIO
5
Run
Deep Stop2
VDDA supply current (analog circuity)
Deep
IDDA
Stop2
Low Voltage Interrupt6
VEI
—
2.5
2.85
V
Low Voltage Interrupt Recovery Hysteresis
VEIH
—
50
—
mV
Power on Reset7
POR
—
1.5
2.0
V
Note:
Run (operating) IDD measured using external square wave clock source (fosc = 4MHz) into XTAL. All inputs 0.2V from rail; no
DC loads; outputs unloaded. All ports configured as inputs; measured with all modules enabled. PLL set to 240MHz out.
1. Running Core, performing 50% NOP and 50% FIR. Clock at 120 MHz.
2. Deep Stop Mode - Operation frequency = 4 MHz, PLL set to 4 MHz, crystal oscillator and time of day module operating.
3. Light Stop Mode - Operation frequency = 120 MHz, PLL set to 240 MHz, crystal oscillator and time of day module operating.
4. IDD includes current for core logic, internal memories, and all internal peripheral logic circuitry.
5. Running core and performing external memory access. Clock at 120 MHz.
6. When VDD drops below VEI max value, an interrupt is generated.
7. Power-on reset occurs whenever the digital supply drops below 1.8V. While power is ramping up, this signal remains active
for as long as the internal 2.5V is below 1.8V no matter how long the ramp up rate is. The internally regulated voltage is
typically 100 mV less than VDD during ramp up until 2.5V is reached, at which time it self-regulates.
56853 Technical Data, Rev. 6
Freescale Semiconductor
25
150
EMI Mode5
MAC Mode1
120
IDD (mA)
90
60
30
0
20
40
60
80
100
120
Figure 4-1 Maximum Run IDDTOTAL vs. Frequency (see Notes 1. and 5. in Table 4-4)
56853 Technical Data, Rev. 6
26
Freescale Semiconductor
Supply Voltage Sequencing and Separation Cautions
4.3 Supply Voltage Sequencing and Separation Cautions
DC Power Supply Voltage
Figure 4-2 shows two situations to avoid in sequencing the VDD and VDDIO, VDDA supplies.
3.3V
VDDIO, VDDA
2
1.8V
Supplies Stable
VDD
1
0
Time
Notes: 1. VDD rising before VDDIO, VDDA
2. VDDIO, VDDA rising much faster than VDD
Figure 4-2 Supply Voltage Sequencing and Separation Cautions
VDD should not be allowed to rise early (1). This is usually avoided by running the regulator for the VDD
supply (1.8V) from the voltage generated by the 3.3V VDDIO supply, see Figure 4-3. This keeps VDD from
rising faster than VDDIO.
VDD should not rise so late that a large voltage difference is allowed between the two supplies (2).
Typically this situation is avoided by using external discrete diodes in series between supplies, as shown
in Figure 4-3. The series diodes forward bias when the difference between VDDIO and VDD reaches
approximately 2.1, causing VDD to rise as VDDIO ramps up. When the VDD regulator begins proper
operation, the difference between supplies will typically be 0.8V and conduction through the diode chain
reduces to essentially leakage current. During supply sequencing, the following general relationship
should be adhered to:
VDDIO > VDD > (VDDIO - 2.1V)
In practice, VDDA is typically connected directly to VDDIO with some filtering.
56853 Technical Data, Rev. 6
Freescale Semiconductor
27
Supply
VDDIO, VDDA
3.3V
Regulator
VDD
1.8V
Regulator
Figure 4-3 Example Circuit to Control Supply Sequencing
4.4 AC Electrical Characteristics
Timing waveforms in Section 4.2 are tested with a VIL maximum of 0.8 V and a VIH minimum of 2.0 V
for all pins except XTAL, which is tested using the input levels in Section 4.2. In Figure 4-4 the levels of
VIH and VIL for an input signal are shown.
Low
VIH
Input Signal
High
90%
50%
10%
Midpoint1
VIL
Fall Time
Rise Time
Note: The midpoint is VIL + (VIH – VIL)/2.
Figure 4-4 Input Signal Measurement References
Figure 4-5 shows the definitions of the following signal states:
•
•
•
Active state, when a bus or signal is driven, and enters a low impedance state.
Tri-stated, when a bus or signal is placed in a high impedance state.
Data Valid state, when a signal level has reached VOL or VOH.
•
Data Invalid state, when a signal level is in transition between VOL and VOH.
Data2 Valid
Data1 Valid
Data1
Data3 Valid
Data2
Data3
Data
Tri-stated
Data Invalid State
Data Active
Data Active
Figure 4-5 Signal States
56853 Technical Data, Rev. 6
28
Freescale Semiconductor
External Clock Operation
4.5 External Clock Operation
The 56853 system clock can be derived from a crystal or an external system clock signal. To generate a
reference frequency using the internal oscillator, a reference crystal must be connected between the
EXTAL and XTAL pins.
4.5.1
Crystal Oscillator
The internal oscillator is designed to interface with a parallel-resonant crystal resonator in the frequency
range specified for the external crystal in Table 4-6. In Figure 4-6 a typical crystal oscillator circuit is
shown. Follow the crystal supplier’s recommendations when selecting a crystal, because crystal
parameters determine the component values required to provide maximum stability and reliable start-up.
The crystal and associated components should be mounted as close as possible to the EXTAL and XTAL
pins to minimize output distortion and start-up stabilization time.
Crystal Frequency = 2–4 MHz (optimized for 4MHz)
EXTAL XTAL
Rz
Sample External Crystal Parameters:
Rz = 10MΩ
TOD_SEL bit in CGM must be set to 0
Figure 4-6 Crystal Oscillator
4.5.2
High Speed External Clock Source (> 4MHz)
The recommended method of connecting an external clock is given in Figure 4-7. The external clock
source is connected to XTAL and the EXTAL pin is held at ground, VDDA, or VDDA/2. The TOD_SEL
bit in CGM must be set to 0.
DSP56853
XTAL
EXTAL
GND,VDDA,
External
Clock
or VDDA/2
(up to 240MHz)
Figure 4-7 Connecting a High Speed External Clock Signal using XTAL
4.5.3
Low Speed External Clock Source (2-4MHz)
The recommended method of connecting an external clock is given in Figure 4-8. The external clock
source is connected to XTAL and the EXTAL pin is held at VDDA/2. The TOD_SEL bit in CGM must be
set to 0.
56853 Technical Data, Rev. 6
Freescale Semiconductor
29
DSP56853
XTAL
EXTAL
External
Clock
(2-4MHz)
VDDA/2
Figure 4-8 Connecting a Low Speed External Clock Signal using XTAL
Table 4-5 External Clock Operation Timing Requirements4
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
Frequency of operation (external clock driver)1
fosc
0
—
240
MHz
Clock Pulse Width4
tPW
6.25
—
—
ns
External clock input rise time2, 4
trise
—
—
TBD
ns
External clock input fall time3, 4
tfall
—
—
TBD
ns
1.
See Figure 4-7 for details on using the recommended connection of an external clock driver.
2.
External clock input rise time is measured from 10% to 90%.
3.
External clock input fall time is measured from 90% to 10%.
4.
Parameters listed are guaranteed by design.
VIH
External
Clock
90%
50%
10%
tPW
tPW
90%
50%
10%
tfall
trise
VIL
Note: The midpoint is VIL + (VIH – VIL)/2.
Figure 4-9 External Clock Timing
56853 Technical Data, Rev. 6
30
Freescale Semiconductor
External Memory Interface Timing
Table 4-6 PLL Timing
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
External reference crystal frequency for the PLL1
fosc
2
4
4
MHz
PLL output frequency
fclk
40
—
240
MHz
PLL stabilization time 2
tplls
—
1
10
ms
1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly.
The PLL is optimized for 4MHz input crystal.
2.
This is the minimum time required after the PLL setup is changed to ensure reliable operation.
4.6 External Memory Interface Timing
The External Memory Interface is designed to access static memory and peripheral devices. Figure 4-10 shows
sample timing and parameters that are detailed in Table 4-7.
The timing of each parameter consists of both a fixed delay portion and a clock related portion; as well as user
controlled wait states. The equation:
t = D + P * (M + W)
should be used to determine the actual time of each parameter. The terms in the above equation are defined as:
t
parameter delay time
D fixed portion of the delay, due to on-chip path delays.
P
the period of the system clock, which determines the execution rate of the part (i.e. when the device is
operating at 120 MHz, P = 8.33 ns).
M Fixed portion of a clock period inherent in the design. This number is adjusted to account for possible
clock duty cycle derating.
W the sum of the applicable wait state controls. See the “Wait State Controls” column of Table 4-7 for
the applicable controls for each parameter. See the EMI chapter of the 83x Peripheral Manual for
details of what each wait state field controls.
Some of the parameters contain two sets of numbers. These parameters have two different paths and clock edges
that must be considered. Check both sets of numbers and use the smaller result. The appropriate entry may change
if the operating frequency of the part changes.
The timing of write cycles is different when WWS = 0 than when WWS > 0. Therefore, some parameters contain
two sets of numbers to account for this difference. The “Wait States Configuration” column of Table 4-7 should be
used to make the appropriate selection.
56853 Technical Data, Rev. 6
Freescale Semiconductor
31
A0-Axx,CS
tRD
tARDD
tARDA
tRDA
tRDRD
RD
tWAC
tAWR
tWRWR
tWRRD
tWR
tRDWR
WR
tDWR
tDOH
tDOS
tAD
tRDD
tDRD
Data Out
D0-D15
Data In
Note: During read-modify-write instructions and internal instructions, the address lines do not change state.
Figure 4-10 External Memory Interface Timing
Table 4-7 External Memory Interface Timing
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98 V, VDDIO = VDDA = 3.0–3.6V, TA = –40× to +120×C, CL £ 50pF, P = 8.333ns
Characteristic
Address Valid to WR Asserted
WR Width Asserted to WR
Deasserted
Symbol
tAWR
tWR
Data Out Valid to WR Asserted
tDWR
Valid Data Out Hold Time after WR
Deasserted
tDOH
Valid Data Out Set Up Time to WR
Deasserted
tDOS
Valid Address after WR
Deasserted
tWAC
Wait States
Configuration
D
M
WWS=0
-0.79
0.50
WWS>0
-1.98
0.69
WWS=0
-0.86
0.19
WWS>0
-0.01
0.00
WWS=0
-1.52
0.00
WWS=0
- 5.69
0.25
WWS>0
-2.10
0.19
WWS>0
-4.66
0.50
-1.47
0.25
-2.36
0.19
-4.67
0.50
-1.60
0.25
Wait States
Controls
Unit
WWSS
ns
WWS
ns
WWSS
ns
WWSH
ns
WWS,WWSS
ns
WWSH
56853 Technical Data, Rev. 6
32
Freescale Semiconductor
Reset, Stop, Wait, Mode Select, and Interrupt Timing
Table 4-7 External Memory Interface Timing (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98 V, VDDIO = VDDA = 3.0–3.6V, TA = –40× to +120×C, CL £ 50pF, P = 8.333ns
D
M
Wait States
Controls
Unit
tRDA
- 0.44
0.00
RWSH
ns
Address Valid to RD Deasserted
tARDD
-2.07
1.00
RWSS,RWS
ns
Valid Input Data Hold after RD
Deasserted
tDRD
0.00
N/A1
—
ns
RD Assertion Width
tRD
-1.34
1.00
RWS
ns
Address Valid to Input Data Valid
tAD
-10.27
1.00
-13.5
1.19
RWSS,RWS
ns
- 0.94
0.00
RWSS
ns
-9.53
1.00
-12.64
1.19
RWSS,RWS
ns
Characteristic
Symbol
RD Deasserted to Address Invalid
Address Valid to RD Asserted
tARDA
RD Asserted to Input Data Valid
tRDD
Wait States
Configuration
WR Deasserted to RD Asserted
tWRRD
-0.75
0.25
WWSH,RWSS
ns
RD Deasserted to RD Asserted
tRDRD
-0.162
0.00
RWSS,RWSH
ns
WR Deasserted to WR Asserted
tWRWR
WWS=0
-0.44
0.75
WWS>0
-0.11
1.00
WWSS, WWSH
ns
0.14
0.50
-0.57
0.69
MDAR, BMDAR,
RWSH, WWSS
ns
RD Deasserted to WR Asserted
tRDWR
1. N/A since device captures data before it deasserts RD
2. If RWSS = RWSH = 0, RD does not deassert during back-to-back reads and D=0.00 should be used.
4.7 Reset, Stop, Wait, Mode Select, and Interrupt Timing
Table 4-8 Reset, Stop, Wait, Mode Select, and Interrupt Timing1, 2
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
See Figure
RESET Assertion to Address, Data and Control
Signals High Impedance
tRAZ
—
11
ns
4-11
Minimum RESET Assertion Duration3
tRA
30
—
ns
4-11
RESET Deassertion to First External Address Output
tRDA
—
120T
ns
4-11
Edge-sensitive Interrupt Request Width
tIRW
1T + 3
—
ns
4-12
56853 Technical Data, Rev. 6
Freescale Semiconductor
33
Table 4-8 Reset, Stop, Wait, Mode Select, and Interrupt Timing1, 2 (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
See Figure
IRQA, IRQB Assertion to External Data Memory
Access Out Valid, caused by first instruction execution
in the interrupt service routine
tIDM
18T
—
ns
4-13
tIDM -FAST
14T
—
tIG
18T
—
ns
4-13
tIG -FAST
14T
—
tIRI
22T
—
ns
4-14
tIRI -FAST
18T
—
1.5T
—
IRQA, IRQB Assertion to General Purpose Output
Valid, caused by first instruction execution in the
interrupt service routine
IRQA Low to First Valid Interrupt Vector Address Out
recovery from Wait State4
Delay from IRQA Assertion (exiting Stop) to External
Data Memory5
tIW
Delay from IRQA Assertion (exiting Wait) to External
Data Memory
Fast6
Normal7
tIF
ns
4-15
18T
22ET
—
—
ns
ns
tRSTO
RSTO pulse width8
normal operation
internal reset mode
4-15
4-16
128ET
8ET
—
—
1.
In the formulas, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns.
2.
Parameters listed are guaranteed by design.
—
—
3. At reset, the PLL is disabled and bypassed. The part is then put into Run mode and tclk assumes the period of the source
clock, txtal, textal or tosc.
4. The minimum is specified for the duration of an edge-sensitive IRQA interrupt required to recover from the Stop state. This is
not the minimum required so that the IRQA interrupt is accepted.
5.
The interrupt instruction fetch is visible on the pins only in Mode 3.
6.
Fast stop mode:
Fast stop recovery applies when external clocking is in use (direct clocking to XTAL) or when fast stop mode recovery is
requested (OMR bit 6 is set to 1). In both cases the PLL and the master clock are unaffected by stop mode entry. Recovery takes
one less cycle and tclk will continue same value it had before stop mode was entered.
7.
Normal stop mode:
As a power saving feature, normal stop mode disables and bypasses the PLL. Stop mode will then shut down the master
clock, recovery will take an extra cycle (to restart the clock), and tclk will resume at the input clock source rate.
8.
ET = External Clock period, For an external crystal frequency of 8MHz, ET=125 ns.
56853 Technical Data, Rev. 6
34
Freescale Semiconductor
Reset, Stop, Wait, Mode Select, and Interrupt Timing
RESET
tRA
tRAZ
tRDA
A0–A20,
D0–D15
First Fetch
CS,
RD, WR
First Fetch
Figure 4-11 Asynchronous Reset Timing
IRQA
IRQB
tIRW
Figure 4-12 External Interrupt Timing (Negative-Edge-Sensitive)
A0–A20,
CS,
RD, WR
First Interrupt Instruction Execution
tIDM
IRQA,
IRQB
a) First Interrupt Instruction Execution
General
Purpose
I/O Pin
tIG
IRQA,
IRQB
b) General Purpose I/O
Figure 4-13 External Level-Sensitive Interrupt Timing
56853 Technical Data, Rev. 6
Freescale Semiconductor
35
IRQA,
IRQB
tIRI
A0–A20,
CS,
RD, WR
First Interrupt Vector
Instruction Fetch
Figure 4-14 Interrupt from Wait State Timing
tIW
IRQA
tIF
A0–A20,
CS,
RD, WR
First Instruction Fetch
Not IRQA Interrupt Vector
Figure 4-15 Recovery from Stop State Using Asynchronous Interrupt Timing
RESET
tRSTO
Figure 4-16 Reset Output Timing
4.8 Host Interface Port
Table 4-9 Host Interface Port Timing1
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
See Figure
Access time
TACKDV
—
13
ns
4-17
Disable time
TACKDZ
3
—
ns
4-17
Time to disassert
TACKREQH
3.5
9
ns
4-17,
4-20
Lead time
TREQACKL
0
—
ns
4-17
4-20
56853 Technical Data, Rev. 6
36
Freescale Semiconductor
Host Interface Port
Table 4-9 Host Interface Port Timing1
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
See Figure
Access time
TRADV
—
13
ns
4-18
4-19
Disable time
TRADX
5
—
ns
4-18
4-19
Disable time
TRADZ
3
—
ns
4-18
4-19
Setup time
TDACKS
3
—
ns
4-20
Hold time
TACKDH
1
—
ns
4-20
Setup time
TADSS
3
—
ns
4-21
4-22
Hold time
TDSAH
1
—
ns
4-21
4-22
Pulse width
TWDS
5
—
ns
4-21
4-22
TACKREQL
4T + 5
5
5T + 9
13
ns
ns
4-17,
4-20
Time to re-assert
1. After second write in 16-bit mode
2. After first write in 16-bit mode
or after write in 8-bit mode
1. The formulas: T = clock cycle. f ipb = 60MHz, T = 16.7ns.
HACK
TACKDZ
TACKDV
HD
TREQACKL
TACKREQH
TACKREQL
HREQ
Figure 4-17 Controller-to-Host DMA Read Mode
56853 Technical Data, Rev. 6
Freescale Semiconductor
37
HA
TRADX
HCS
HDS
HRW
TRADV
TRADZ
HD
Figure 4-18 Single Strobe Read Mode
HA
TRADX
HCS
HWR
HRD
TRADZ
TRADV
HD
Figure 4-19 Dual Strobe Read Mode
HACK
TDACKS
TACKDH
HD
TREQACKL
TACKREQH
TACKREQL
HREQ
Figure 4-20 Host-to-Controller DMA Write Mode
56853 Technical Data, Rev. 6
38
Freescale Semiconductor
Host Interface Port
HA
TDSAH
HCS
TWDS
HDS
TDSAH
HRW
TADSS
TADSS
TDSAH
HD
Figure 4-21 Single Strobe Write Mode
HA
HCS
TWDS
HWR
TDSAH
TADSS
HRD
TADSS
HD
Figure 4-22 Dual Strobe Write Mode
56853 Technical Data, Rev. 6
Freescale Semiconductor
39
4.9 Serial Peripheral Interface (SPI) Timing
Table 4-10 SPI Timing 1
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Cycle time
Master
Slave
Min
Max
Unit
25
25
—
—
ns
ns
—
12.5
—
—
ns
ns
—
12.5
—
—
ns
ns
9
12.5
—
—
12
12.5
—
—
ns
ns
10
2
—
—
ns
ns
0
2
—
—
ns
ns
15
ns
ns
4-26
5
9
ns
ns
4-26
2
—
—
2
14
ns
ns
0
0
—
—
ns
ns
—
—
11.5
10.0
ns
ns
—
—
9.7
9.0
ns
ns
tC
Enable lead time
Master
Slave
tELD
Enable lag time
Master
Slave
tELG
Clock (SCLK) high time
Master
Slave
tCH
Clock (SCLK) low time
Master
Slave
tCL
Data set-up time required for inputs
Master
Slave
tDS
Data hold time required for inputs
Master
Slave
tDH
Access time (time to data active from high-impedance state)
Slave
tA
Disable time (hold time to high-impedance state)
Slave
tD
Data valid for outputs
Master
Slave (after enable edge)
tDV
Data invalid
Master
Slave
tDI
Rise time
Master
Slave
tR
Fall time
Master
Slave
tF
See Figure
4-23, 4-24,
4-25, 4-26
4-26
4-26
ns
ns
4-23, 4-24,
4-25, 4-26
4-26
4-23, 4-24,
4-25, 4-26
4-23, 4-24,
4-25, 4-26
4-23, 4-24,
4-25, 4-26
4-23, 4-24,
4-25, 4-26
4-23, 4-24,
4-25, 4-26
4-23, 4-24,
4-25, 4-26
56853 Technical Data, Rev. 6
40
Freescale Semiconductor
Serial Peripheral Interface (SPI) Timing
SS
SS is held High on master
(Input)
tC
tR
tF
tCL
SCLK (CPOL = 0)
(Output)
tCH
tF
tR
tCL
SCLK (CPOL = 1)
(Output)
tDH
tDS
MISO
(Input)
tCH
tCH
MSB in
Bits 14–1
tDI(ref)
tDV
tDI
MOSI
(Output)
LSB in
Master MSB out
Bits 14–1
Master LSB out
tR
tF
Figure 4-23 SPI Master Timing (CPHA = 0)
SS
(Input)
SS is held High on master
tC
tF
tCL
SCLK (CPOL = 0)
(Output)
tCH
tF
tCL
SCLK (CPOL = 1)
(Output)
tCH
MISO
(Input)
MSB in
tDS
tR
tDH
Bits 14–1
tDI
tDV(ref)
MOSI
(Output)
tR
Master MSB out
LSB in
tDV
Bits 14– 1
tF
Master LSB out
tR
Figure 4-24 SPI Master Timing (CPHA = 1)
56853 Technical Data, Rev. 6
Freescale Semiconductor
41
SS
(Input)
tC
tF
tR
tCL
SCLK (CPOL = 0)
(Input)
tELG
tCH
tELD
tCL
SCLK (CPOL = 1)
(Input)
tA
tCH
MISO
(Output)
Slave MSB out
tDS
tDH
MOSI
(Input)
MSB in
tF
tR
tD
Bits 14–1
Slave LSB out
tDV
tDI
Bits 14–1
tDI
LSB in
Figure 4-25 SPI Slave Timing (CPHA = 0)
SS
(Input)
tF
tC
tR
tCL
SCLK (CPOL = 0)
(Input)
tCH
tELG
tELD
SCLK (CPOL = 1)
(Input)
tCL
tDV
tA
MISO
(Output)
tF
tCH
Slave MSB out
tR
Bits 14–1
tDV
tDS
tD
Slave LSB out
tDI
tDH
MOSI
(Input)
MSB in
Bits 14–1
LSB in
Figure 4-26 SPI Slave Timing (CPHA = 1)
56853 Technical Data, Rev. 6
42
Freescale Semiconductor
Quad Timer Timing
4.10 Quad Timer Timing
Table 4-11 Quad Timer Timing1, 2
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
PIN
2T + 3
—
ns
Timer input high/low period
PINHL
1T + 3
—
ns
Timer output period
POUT
2T - 3
—
ns
POUTHL
1T - 3
—
ns
Timer input period
Timer output high/low period
1.
In the formulas listed, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns.
2.
Parameters listed are guaranteed by design.
Timer Inputs
PIN
PINHL
PINHL
POUT
POUTHL
POUTHL
Timer Outputs
Figure 4-27 Timer Timing
4.11 Enhanced Synchronous Serial Interface (ESSI) Timing
Table 4-12 ESSI Master Mode1 Switching Characteristics
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
fs
—
SCK period3
tSCKW
SCK high time
SCK low time
SCK frequency
Output clock rise/fall time
Delay from SCK high to SC2 (bl) high - Master5
Max
Units
—
152
MHz
66.7
—
—
ns
tSCKH
33.44
—
—
ns
tSCKL
33.44
—
—
ns
—
—
4
—
ns
tTFSBHM
-1.0
—
1.0
ns
56853 Technical Data, Rev. 6
Freescale Semiconductor
43
Table 4-12 ESSI Master Mode1 Switching Characteristics (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
Max
Units
Delay from SCK high to SC2 (wl) high - Master5
tTFSWHM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (bl) high - Master5
tRFSBHM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (wl) high - Master5
tRFSWHM
-1.0
—
1.0
ns
Delay from SCK high to SC2 (bl) low - Master5
tTFSBLM
-1.0
—
1.0
ns
Delay from SCK high to SC2 (wl) low - Master5
tTFSWLM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (bl) low - Master5
tRFSBLM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (wl) low - Master5
tRFSWLM
-1.0
—
1.0
ns
SCK high to STD enable from high impedance - Master
tTXEM
-0.1
—
2
ns
SCK high to STD valid - Master
tTXVM
-0.1
—
2
ns
SCK high to STD not valid - Master
tTXNVM
-0.1
—
—
ns
SCK high to STD high impedance - Master
tTXHIM
-4
—
0
ns
SRD Setup time before SC0 low - Master
tSM
4
—
—
ns
SRD Hold time after SC0 low - Master
tHM
4
—
—
ns
Synchronous Operation (in addition to standard internal clock parameters)
SRD Setup time before SCK low - Master
tTSM
4
—
—
ns
SRD Hold time after SCK low - Master
tTHM
4
—
—
ns
1. Master mode is internally generated clocks and frame syncs
2. Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for an 120MHz part.
3. All the timings for the ESSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR)
and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync
have been inverted, all the timings remain valid by inverting the clock signal SCK/SC0 and/or the frame sync SC2/SC1 in
the tables and in the figures.
4. 50 percent duty cycle
5. bl = bit length; wl = word length
56853 Technical Data, Rev. 6
44
Freescale Semiconductor
Enhanced Synchronous Serial Interface (ESSI) Timing
tSCKH
tSCKW
tSCKL
SCK output
tTFSBHM
tTFSBLM
SC2 (bl) output
tTFSWHM
tTFSWLM
SC2 (wl) output
tTXVM
tTXEM
tTXNVM
tTXHIM
First Bit
STD
Last Bit
SC0 output
tRFSBHM
tRFBLM
SC1 (bl) output
tRFSWHM
tRFSWLM
SC1 (wl) output
tSM
tHM
tTSM
tTHM
SRD
Figure 4-28 Master Mode Timing Diagram
Table 4-13 ESSI Slave Mode1 Switching Characteristics
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
Max
Units
fs
—
—
152
MHz
SCK period3
tSCKW
66.7
—
—
ns
SCK high time
tSCKH
33.44
—
—
ns
SCK low time
tSCKL
33.44
—
—
ns
—
—
4
—
ns
tTFSBHS
-1
—
29
ns
SCK frequency
Output clock rise/fall time
Delay from SCK high to SC2 (bl) high - Slave5
56853 Technical Data, Rev. 6
Freescale Semiconductor
45
Table 4-13 ESSI Slave Mode1 Switching Characteristics (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
Max
Units
Delay from SCK high to SC2 (wl) high - Slave5
tTFSWHS
-1
—
29
ns
Delay from SC0 high to SC1 (bl) high - Slave5
tRFSBHS
-1
—
29
ns
Delay from SC0 high to SC1 (wl) high - Slave5
tRFSWHS
-1
—
29
ns
Delay from SCK high to SC2 (bl) low - Slave5
tTFSBLS
-29
—
29
ns
Delay from SCK high to SC2 (wl) low - Slave5
tTFSWLS
-29
—
29
ns
Delay from SC0 high to SC1 (bl) low - Slave5
tRFSBLS
-29
—
29
ns
Delay from SC0 high to SC1 (wl) low - Slave5
tRFSWLS
-29
—
29
ns
SCK high to STD enable from high impedance - Slave
tTXES
—
—
15
ns
SCK high to STD valid - Slave
tTXVS
4
—
15
ns
SC2 high to STD enable from high impedance (first bit) - Slave
tFTXES
4
—
15
ns
SC2 high to STD valid (first bit) - Slave
tFTXVS
4
—
15
ns
SCK high to STD not valid - Slave
tTXNVS
4
—
15
ns
SCK high to STD high impedance - Slave
tTXHIS
4
—
15
ns
SRD Setup time before SC0 low - Slave
tSS
4
—
—
ns
SRD Hold time after SC0 low - Slave
tHS
4
—
—
ns
Synchronous Operation (in addition to standard external clock parameters)
SRD Setup time before SCK low - Slave
tTSS
4
—
—
ns
SRD Hold time after SCK low - Slave
tTHS
4
—
—
ns
1. Slave mode is externally generated clocks and frame syncs
2. Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for a 120MHz part.
3. All the timings for the ESSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR)
and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync
have been inverted, all the timings remain valid by inverting the clock signal SCK/SC0 and/or the frame sync SC2/SC1 in
the tables and in the figures.
4. 50 percent duty cycle
5. bl = bit length; wl = word length
56853 Technical Data, Rev. 6
46
Freescale Semiconductor
Serial Communication Interface (SCI) Timing
tSCKW
tSCKH
tSCKL
SCK input
tTFSBLS
tTFSBHS
SC2 (bl) input
tTFSWHS
tTFSWLS
SC2 (wl) input
tFTXVS
tFTXES
tTXNVS
tTXVS
tTXES
tTXHIS
First Bit
STD
SC0 input
Last Bit
tRFBLS
tRFSBHS
SC1 (bl) input
tRFSWHS
tRFSWLS
SC1 (wl) input
tSS
tTSS
tHS
tTHS
SRD
Figure 4-29 Slave Mode Clock Timing
4.12 Serial Communication Interface (SCI) Timing
Table 4-14 SCI Timing4
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
BR
—
(fMAX)/(32)
Mbps
RXD2 Pulse Width
RXDPW
0.965/BR
1.04/BR
ns
TXD3 Pulse Width
TXDPW
0.965/BR
1.04/BR
ns
Baud Rate1
1.
fMAX is the frequency of operation of the system clock in MHz.
2.
The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1.
3.
The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1.
4.
Parameters listed are guaranteed by design.
56853 Technical Data, Rev. 6
Freescale Semiconductor
47
RXD
SCI receive
data pin
(Input)
RXDPW
Figure 4-30 RXD Pulse Width
TXD
SCI receive
data pin
(Input)
TXDPW
Figure 4-31 TXD Pulse Width
4.13 JTAG Timing
Table 4-15 JTAG Timing1, 3
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
TCK frequency of operation2
fOP
DC
30
MHz
TCK cycle time
tCY
33.3
—
ns
TCK clock pulse width
tPW
16.6
—
ns
TMS, TDI data setup time
tDS
3
—
ns
TMS, TDI data hold time
tDH
3
—
ns
TCK low to TDO data valid
tDV
—
12
ns
TCK low to TDO tri-state
tTS
—
10
ns
tTRST
35
—
ns
tDE
4T
—
ns
TRST assertion time
DE assertion time
1. Timing is both wait state and frequency dependent. For the values listed, T = clock cycle. For 120MHz
operation, T = 8.33ns.
2.
TCK frequency of operation must be less than 1/4 the processor rate.
3.
Parameters listed are guaranteed by design.
56853 Technical Data, Rev. 6
48
Freescale Semiconductor
JTAG Timing
tCY
tPW
tPW
VIH
VM
TCK
(Input)
VM
VIL
VM = VIL + (VIH – VIL)/2
Figure 4-32 Test Clock Input Timing Diagram
TCK
(Input)
tDS
TDI
TMS
(Input)
tDH
Input Data Valid
tDV
TDO
(Output)
Output Data Valid
tTS
TDO
(Output)
Figure 4-33 Test Access Port Timing Diagram
TRST
(Input)
tTRST
Figure 4-34 TRST Timing Diagram
DE
tDE
Figure 4-35 Enhanced OnCE—Debug Event
56853 Technical Data, Rev. 6
Freescale Semiconductor
49
4.14 GPIO Timing
Table 4-16 GPIO Timing1, 2
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
PIN
2T + 3
—
ns
GPIO input high/low period
PINHL
1T + 3
—
ns
GPIO output period
POUT
2T - 3
—
ns
POUTHL
1T - 3
—
ns
GPIO input period
GPIO output high/low period
1.
In the formulas listed, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns
2.
Parameters listed are guaranteed by design.
GPIO Inputs
PIN
PINHL
PINHL
POUT
POUTHL
POUTHL
GPIO Outputs
Figure 4-36 GPIO Timing
56853 Technical Data, Rev. 6
50
Freescale Semiconductor
Package and Pin-Out Information 56853
Part 5 Packaging
5.1 Package and Pin-Out Information 56853
VSSIO
TIO0
VDDIO
TIO1
TIO2
TIO3
VSS
TXD1
RXD1
VSSIO
VDDIO
VDDIO
D5
D4
D3
D2
D1
HRWB
HA2
HA1
HA0
VSS
VDD
VDD
CS3
CS2
CS1
CS0
VSSIO
D0
VDDIO
A20
A19
A18
A17
A16
TXD0
RXD0
This section contains package and pin-out information for the 128-pin LQFP configuration of the 56853.
PIN 65
PIN 103
ORIENTATION
MARK
PIN 39
VDD
VSS
VSSIO
VDDIO
A15
A14
A13
A12
VSSIO
VDDIO
TCK
TMS
TDI
TDO
TRST
DE
VSS
VDD
A11
A10
A9
A8
VSSIO
VDDIO
HD7
HD6
IRQA
IRQB
VDDA
VSSA
XTAL
EXTAL
A4
A5
A6
A7
HD0
HD1
HD2
CLKO
RSTO
RESET
HD3
HD4
HD5
RD
WR
A0
A1
A2
A3
VDD
VSS
MODA
MODB
MODC
VDDIO
VSSIO
PIN 1
MISO
MOSI
SCK
SS
VDDIO
VSSIO
HDS
HCS
HREQ
HACK
D6
D7
D8
D9
D10
VDD
VSS
VDDIO
VSSIO
STD0
SRD0
SCK0
SC00
SC01
SC02
D11
D12
VDDIO
VSSIO
D13
D14
D15
Figure 5-1 Top View, 56853 128-pin LQFP Package
56853 Technical Data, Rev. 6
Freescale Semiconductor
51
Table 5-1 56853 Pin Identification by Pin Number
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
1
MISO
33
CLKO
65
RXD0
97
TIO3
2
MOSI
34
RSTO
66
TXDO
98
TIO2
3
SCK
35
RESET
67
A16
99
TIO1
4
SS
36
HD3
68
A17
100
VDDIO
5
VDDIO
37
HD4
69
A18
101
TIO0
6
VSSIO
38
HD5
70
A19
102
VSSIO
7
RD
39
HD6
71
A20
103
HDS
8
WR
40
HD7
72
VDDIO
104
HCS
9
A0
41
VDDIO
73
D0
105
HREQ
10
A1
42
VSSIO
74
VSSIO
106
HACK
11
A2
43
A8
75
CS0
107
D6
12
A3
44
A9
76
CS1
108
D7
13
VDD
45
A10
77
CS2
109
D8
14
VSS
46
A11
78
CS3
110
D9
15
MODA
47
VDD
79
VDD
111
D10
16
MODB
48
VSS
80
VDD
112
VDD
17
MODC
49
DE
81
VSS
113
VSS
18
VDDIO
50
TRST
82
HA0
114
VDDIO
19
VSSIO
51
TDO
83
HA1
115
VSSIO
20
IRQA
52
TDI
84
HA2
116
STD0
21
IRQB
53
TMS
85
HRWB
117
SRD0
22
VDDA
54
TCK
86
D1
118
SCK0
23
VSSA
55
VDDIO
87
D2
119
SC00
24
XTAL
56
VSSIO
88
D3
120
SC01
25
EXTAL
57
A12
89
D4
121
SC02
26
A4
58
A13
90
D5
122
D11
27
A5
59
A14
91
VDDIO
123
D12
28
A6
60
A15
92
VDDIO
124
VDDIO
29
A7
61
VDDIO
93
VSSIO
125
VSSIO
30
HD0
62
VSSIO
94
RXD1
126
D13
31
HD1
63
VSS
95
TXD1
127
D14
32
HD2
64
VDD
96
VSS
128
D15
56853 Technical Data, Rev. 6
52
Freescale Semiconductor
Package and Pin-Out Information 56853
102
65
103
64
128
39
38
DIM
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M,
1994.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE H IS LOCATED AT BOTTOM OF LEAD AND IS
COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE
PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE.
4. DATUMS A, B, AND D TO BE DETERMINED AT DATUM PLANE
H.
5. DIMENSIONS D AND E TO BE DETERMINED AT SEATING
PLANE C.
6. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE.
DIMENSIONS D1 AND E1 DO INCLUDE MOLD MISMATCH
AND ARE DETERMINED AT DATUM PLANE H.
7. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION.
DAMBAR PROTRUSION SHALL NOT CAUSE THE b
DIMENSION TO EXCEED 0.35.
Case Outline - 1129-01
A
A1
A2
b
b1
c
c1
D
D1
e
E
E1
L
L1
L2
S
R1
R2
0
01
02
MILLIMETERS
MIN
MAX
--1.60
0.05
0.15
1.35
1.45
0.17
0.27
0.17
0.23
0.09
0.20
0.09
0.16
22.00 BSC
20.00BSC
0.50 BSC
16.00 BSC
14.00 BSC
0.45
0.75
1.00 REF
0.50 REF
0.20
--0.08
--0.08
0.20
0o
0
o
11o
7o
--13o
Figure 5-2 128-pin LQFP Mechanical Information
Please see www.freescale.com for the most current case outline.
56853 Technical Data, Rev. 6
Freescale Semiconductor
53
Part 6 Design Considerations
6.1 Thermal Design Considerations
An estimation of the chip junction temperature, TJ, in °C can be obtained from the equation:
Equation 1:
TJ = TA + (PD x RθJA)
Where:
TA = ambient temperature °C
RθJA = package junction-to-ambient thermal resistance °C/W
PD = power dissipation in package
Historically, thermal resistance has been expressed as the sum of a junction-to-case thermal resistance and a
case-to-ambient thermal resistance:
Equation 2:
RθJA = RθJC + RθCA
Where:
RθJA = package junction-to-ambient thermal resistance °C/W
RθJC = package junction-to-case thermal resistance °C/W
RθCA = package case-to-ambient thermal resistance °C/W
RθJC is device-related and cannot be influenced by the user. The user controls the thermal environment to change
the case-to-ambient thermal resistance, RθCA. For example, the user can change the air flow around the device, add
a heat sink, change the mounting arrangement on the Printed Circuit Board (PCB), or otherwise change the thermal
dissipation capability of the area surrounding the device on the PCB. This model is most useful for ceramic packages
with heat sinks; some 90% of the heat flow is dissipated through the case to the heat sink and out to the ambient
environment. For ceramic packages, in situations where the heat flow is split between a path to the case and an
alternate path through the PCB, analysis of the device thermal performance may need the additional modeling
capability of a system level thermal simulation tool.
The thermal performance of plastic packages is more dependent on the temperature of the PCB to which the package
is mounted. Again, if the estimations obtained from RθJA do not satisfactorily answer whether the thermal
performance is adequate, a system level model may be appropriate.
A complicating factor is the existence of three common definitions for determining the junction-to-case thermal
resistance in plastic packages:
•
Measure the thermal resistance from the junction to the outside surface of the package (case) closest to the
chip mounting area when that surface has a proper heat sink. This is done to minimize temperature variation
across the surface.
•
Measure the thermal resistance from the junction to where the leads are attached to the case. This definition
is approximately equal to a junction to board thermal resistance.
•
Use the value obtained by the equation (TJ – TT)/PD where TT is the temperature of the package case
determined by a thermocouple.
As noted above, the junction-to-case thermal resistances quoted in this data sheet are determined using the first
definition. From a practical standpoint, that value is also suitable for determining the junction temperature from a
case thermocouple reading in forced convection environments. In natural convection, using the junction-to-case
56853 Technical Data, Rev. 6
54
Freescale Semiconductor
Electrical Design Considerations
thermal resistance to estimate junction temperature from a thermocouple reading on the case of the package will
estimate a junction temperature slightly hotter than actual. Hence, the new thermal metric, Thermal Characterization
Parameter, or ΨJT, has been defined to be (TJ – TT)/PD. This value gives a better estimate of the junction temperature
in natural convection when using the surface temperature of the package. Remember that surface temperature
readings of packages are subject to significant errors caused by inadequate attachment of the sensor to the surface
and to errors caused by heat loss to the sensor. The recommended technique is to attach a 40-gauge thermocouple
wire and bead to the top center of the package with thermally conductive epoxy.
6.2 Electrical Design Considerations
CAUTION
This device contains protective circuitry to guard against
damage due to high static voltage or electrical fields.
However, normal precautions are advised to avoid
application of any voltages higher than maximum rated
voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an
appropriate voltage level.
Use the following list of considerations to assure correct operation:
•
Provide a low-impedance path from the board power supply to each VDD pin on the device, and from the
board ground to each VSS (GND) pin.
•
The minimum bypass requirement is to place six 0.01–0.1 μF capacitors positioned as close as possible to
the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each
of the ten VDD/VSS pairs, including VDDA/VSSA.
•
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND)
pins are less than 0.5 inch per capacitor lead.
•
Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and GND.
•
Bypass the VDD and GND layers of the PCB with approximately 100 μF, preferably with a high-grade
capacitor such as a tantalum capacitor.
•
Because the device’s output signals have fast rise and fall times, PCB trace lengths should be minimal.
•
Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance.
This is especially critical in systems with higher capacitive loads that could create higher transient currents
in the VDD and GND circuits.
•
All inputs must be terminated (i.e., not allowed to float) using CMOS levels.
•
Take special care to minimize noise levels on the VDDA and VSSA pins.
•
When using Wired-OR mode on the SPI or the IRQx pins, the user must provide an external pull-up device.
56853 Technical Data, Rev. 6
Freescale Semiconductor
55
•
Designs that utilize the TRST pin for JTAG port or Enhance OnCE module functionality (such as
development or debugging systems) should allow a means to assert TRST whenever RESET is asserted, as
well as a means to assert TRST independently of RESET. Designs that do not require debugging
functionality, such as consumer products, should tie these pins together.
•
The internal POR (Power on Reset) will reset the part at power on with reset asserted or pulled high but
requires that TRST be asserted at power on.
56853 Technical Data, Rev. 6
56
Freescale Semiconductor
Electrical Design Considerations
Part 7 Ordering Information
Table 7-1 lists the pertinent information needed to place an order. Consult a Freescale Semiconductor
sales office or authorized distributor to determine availability and to order parts.
Table 7-1 56853 Ordering Information
Part
Supply
Voltage
DSP56853
1.8V, 3.3V
DSP56853
1.8V, 3.3V
Pin
Count
Frequency
(MHz)
Order Number
Low-Profile Quad Flat Pack (LQFP)
128
120
DSP56853FG120
Low-Profile Quad Flat Pack (LQFP)
128
120
DSP56853FGE *
Package Type
*This package is RoHS compliant.
56853 Technical Data, Rev. 6
Freescale Semiconductor
57
56853 Technical Data, Rev. 6
58
Freescale Semiconductor
Electrical Design Considerations
56853 Technical Data, Rev. 6
Freescale Semiconductor
59
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064, Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semiconductor reserves the right to make changes without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
application in which the failure of the Freescale Semiconductor product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor,
Inc. All other product or service names are the property of their respective owners.
This product incorporates SuperFlash® technology licensed from SST.
© Freescale Semiconductor, Inc. 2005. All rights reserved.
DSP56853
Rev. 6
01/2007