GSI GS8320E18T

Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
2M x 18, 1M x 32, 1M x 36
36Mb Sync Burst SRAMs
100-Pin TQFP
Commercial Temp
Industrial Temp
Features
250 MHz–133 MHz
2.5 V or 3.3 V VDD
2.5 V or 3.3 V I/O
interleave order with the Linear Burst Order (LBO) input. The
Burst function need not be used. New addresses can be loaded
on every cycle with no degradation of chip performance.
• FT pin for user-configurable flow through or pipeline
operation
• Dual Cycle Deselect (DCD) operation
• 2.5 V or 3.3 V +10%/–10% core power supply
• 2.5 V or 3.3 V I/O supply
• LBO pin for Linear or Interleaved Burst mode
• Internal input resistors on mode pins allow floating mode pins
• Default to Interleaved Pipeline mode
• Byte Write (BW) and/or Global Write (GW) operation
• Internal self-timed write cycle
• Automatic power-down for portable applications
• JEDEC-standard 100-lead TQFP package
• Pb-Free 100-lead TQFP package available
Flow Through/Pipeline Reads
The function of the Data Output register can be controlled by
the user via the FT mode pin (Pin 14). Holding the FT mode
pin low places the RAM in Flow Through mode, causing
output data to bypass the Data Output Register. Holding FT
high places the RAM in Pipeline mode, activating the risingedge-triggered Data Output Register.
DCD Pipelined Reads
The GS8320E18/32/36T is a DCD (Dual Cycle Deselect)
pipelined synchronous SRAM. SCD (Single Cycle Deselect)
versions are also available. DCD SRAMs pipeline disable
commands to the same degree as read commands. DCD RAMs
hold the deselect command for one full cycle and then begin
turning off their outputs just after the second rising edge of
clock.
Functional Description
Applications
The GS8320E18/32/36T is a 37,748,736-bit high performance
synchronous SRAM with a 2-bit burst address counter.
Although of a type originally developed for Level 2 Cache
applications supporting high performance CPUs, the device
now finds application in synchronous SRAM applications,
ranging from DSP main store to networking chip set support.
Byte Write and Global Write
Byte write operation is performed by using Byte Write enable
(BW) input combined with one or more individual byte write
signals (Bx). In addition, Global Write (GW) is available for
writing all bytes at one time, regardless of the Byte Write
control inputs.
Controls
Addresses, data I/Os, chip enables (E1, E2, E3), address burst
control inputs (ADSP, ADSC, ADV), and write control inputs
(Bx, BW, GW) are synchronous and are controlled by a
positive-edge-triggered clock input (CK). Output enable (G)
and power down control (ZZ) are asynchronous inputs. Burst
cycles can be initiated with either ADSP or ADSC inputs. In
Burst mode, subsequent burst addresses are generated
internally and are controlled by ADV. The burst address
counter may be configured to count in either linear or
Sleep Mode
Low power (Sleep mode) is attained through the assertion
(High) of the ZZ signal, or by stopping the clock (CK).
Memory data is retained during Sleep mode.
Core and Interface Voltages
The GS8320E18/32/36T operates on a 2.5 V or 3.3 V power
supply. All input are 3.3 V and 2.5 V compatible. Separate
output power (VDDQ) pins are used to decouple output noise
from the internal circuits and are 3.3 V and 2.5 V compatible.
Parameter Synopsis
Pipeline
3-1-1-1
Flow
Through
2-1-1-1
Rev: 1.01 10/2004
tKQ
tCycle
Curr (x18)
Curr (x32/x36)
tKQ
tCycle
Curr (x18)
Curr (x32/x36)
-250 -225 -200 -166 -150 -133 Unit
2.5 2.7 3.0 3.5 3.8 4.0 ns
4.0 4.4 5.0 6.0 6.6 7.5 ns
285
350
6.5
6.5
265
320
7.0
7.0
245
295
7.5
7.5
220 210 185 mA
260 240 215 mA
8.0 8.5 8.5 ns
8.0 8.5 8.5 ns
205
235
195
225
185
210
175 165 155 mA
200 190 175 mA
1/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
A
A
E1
E2
NC
NC
BB
BA
E3
VDD
VSS
CK
GW
BW
G
ADSC
ADSP
ADV
A
A
GS8320E18 100-Pin TQFP Pinout
NC
NC
NC
VDDQ
A
NC
NC
VDDQ
VSS
NC
DQPA
DQA
DQA
VSS
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
NC
NC
VSS
VDDQ
NC
NC
NC
LBO
A
A
A
A
A1
A0
NC
A
VSS
VDD
A
A
A
A
A
A
A
A
A
VSS
NC
NC
DQB
DQB
VSS
VDDQ
DQB
DQB
FT
VDD
NC
VSS
DQB
DQB
VDDQ
VSS
DQB
DQB
DQPB
NC
VSS
VDDQ
NC
NC
NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
1
80
2
79
3
78
4
77
5
76
6
75
7
74
8
73
9
72
2M x 18
10
71
Top View
11
70
12
69
13
68
14
67
15
66
16
65
17
64
18
63
19
62
20
61
21
60
22
59
23
58
24
57
25
56
26
55
27
54
28
53
29
52
30
51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Rev: 1.01 10/2004
2/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
A
A
E1
E2
BD
BC
BB
BA
E3
VDD
VSS
CK
GW
BW
G
ADSC
ADSP
ADV
A
A
GS8320E32 100-Pin TQFP Pinout
NC
DQC
DQC
VDDQ
VSS
DQC
DQC
DQC
DQC
VSS
VDDQ
DQC
DQC
NC
DQB
DQB
VDDQ
VSS
DQB
DQB
DQB
DQB
VSS
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
DQA
DQA
VSS
VDDQ
DQA
DQA
NC
LBO
A
A
A
A
A1
A0
NC
A
VSS
VDD
A
A
A
A
A
A
A
A
A
FT
VDD
NC
VSS
DQD
DQD
VDDQ
VSS
DQD3
DQD
DQD
DQD
VSS
VDDQ
DQD
DQD
NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
1
80
2
79
3
78
4
77
5
76
6
75
7
74
8
73
9
72
1M x 32
10
71
Top View
11
70
12
69
13
68
14
67
15
66
16
65
17
64
18
63
19
62
20
61
21
60
22
59
23
58
24
57
25
56
26
55
27
54
28
53
29
52
30
51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Rev: 1.01 10/2004
3/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
A
A
E1
E2
BD
BC
BB
BA
E3
VDD
VSS
CK
GW
BW
G
ADSC
ADSP
ADV
A
A
GS8320E36 100-Pin TQFP Pinout
DQPC
DQC
DQC
VDDQ
VSS
DQC
DQC
DQC
DQC
VSS
VDDQ
DQC
DQC
DQPB
DQB
DQB
VDDQ
VSS
DQB
DQB
DQB
DQB
VSS
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
DQA
DQA
VSS
VDDQ
DQA
DQA
DQPA
LBO
A
A
A
A
A1
A0
NC
A
VSS
VDD
A
A
A
A
A
A
A
A
A
FT
VDD
NC
VSS
DQD
DQD
VDDQ
VSS
DQD3
DQD
DQD
DQD
VSS
VDDQ
DQD
DQD
DQPD
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
1
80
2
79
3
78
4
77
5
76
6
75
7
74
8
73
9
72
1M x 32
10
71
Top View
11
70
12
69
13
68
14
67
15
66
16
65
17
64
18
63
19
62
20
61
21
60
22
59
23
58
24
57
25
56
26
55
27
54
28
53
29
52
30
51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Rev: 1.01 10/2004
4/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
TQFP Pin Description
Symbol
Type
Description
A 0, A 1
I
Address field LSBs and Address Counter preset Inputs
A
I
Address Inputs
DQA
DQB1
DQC
DQD
I/O
Data Input and Output pins
NC
No Connect
BW
I
Byte Write—Writes all enabled bytes; active low
BA , BB
I
Byte Write Enable for DQA, DQB Data I/Os; active low
BC , BD
I
Byte Write Enable for DQC, DQD Data I/Os; active low
CK
I
Clock Input Signal; active high
GW
I
Global Write Enable—Writes all bytes; active low
E 1, E 3
I
Chip Enable; active low
E2
I
Chip Enable; active high
G
I
Output Enable; active low
ADV
I
Burst address counter advance enable; active low
ADSP, ADSC
I
Address Strobe (Processor, Cache Controller); active low
ZZ
I
Sleep Mode control; active high
FT
I
Flow Through or Pipeline mode; active low
LBO
I
Linear Burst Order mode; active low
VDD
I
Core power supply
VSS
I
I/O and Core Ground
VDDQ
I
Output driver power supply
Rev: 1.01 10/2004
5/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
GS8320E18/32/36 Block Diagram
A0–An
Register
D
Q
A0
A0
D0
A1
Q0
A1
D1
Q1
Counter
Load
A
LBO
ADV
Memory
Array
CK
ADSC
ADSP
Q
D
Register
GW
BW
BA
D
Q
Register
D
36
Q
BB
36
4
Register
D
Q
D
Q
D
Q
Register
Register
D
Q
Register
BC
BD
Register
D
Q
Register
E1
E2
E3
D
Q
Register
D
Q
FT
G
ZZ
1
Power Down
Control
DQx1–DQx9
Note: Only x36 version shown for simplicity.
Rev: 1.01 10/2004
6/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Mode Pin Functions
Mode Name
Pin Name
Burst Order Control
LBO
Output Register Control
FT
Power Down Control
ZZ
State
Function
L
Linear Burst
H
Interleaved Burst
L
Flow Through
H or NC
Pipeline
L or NC
Active
H
Standby, IDD = ISB
Note:
There is a pull-up device on the FT pin and a pull-down device on the ZZ pin, so this input pin can be unconnected and the chip will operate in
the default states as specified in the above tables.
Burst Counter Sequences
Linear Burst Sequence
Interleaved Burst Sequence
A[1:0] A[1:0] A[1:0] A[1:0]
A[1:0] A[1:0] A[1:0] A[1:0]
1st address
00
01
10
11
1st address
00
01
10
11
2nd address
01
10
11
00
2nd address
01
00
11
10
3rd address
10
11
00
01
3rd address
10
11
00
01
4th address
11
00
01
10
4th address
11
10
01
00
Note:
The burst counter wraps to initial state on the 5th clock.
Note:
The burst counter wraps to initial state on the 5th clock.
BPR 1999.05.18
Rev: 1.01 10/2004
7/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Byte Write Truth Table
Function
GW
BW
BA
BB
BC
BD
Notes
Read
H
H
X
X
X
X
1
Read
H
L
H
H
H
H
1
Write byte a
H
L
L
H
H
H
2, 3
Write byte b
H
L
H
L
H
H
2, 3
Write byte c
H
L
H
H
L
H
2, 3, 4
Write byte d
H
L
H
H
H
L
2, 3, 4
Write all bytes
H
L
L
L
L
L
2, 3, 4
Write all bytes
L
X
X
X
X
X
Notes:
1. All byte outputs are active in read cycles regardless of the state of Byte Write Enable inputs.
2. Byte Write Enable inputs BA, BB, BC and/or BD may be used in any combination with BW to write single or multiple bytes.
3. All byte I/Os remain High-Z during all write operations regardless of the state of Byte Write Enable inputs.
4. Bytes “C” and “D” are only available on the x32 and x36 versions.
Rev: 1.01 10/2004
8/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Synchronous Truth Table
Operation
Address
Used
State
Diagram
Key5
E1
E2
Deselect Cycle, Power Down
None
X
H
X
X
Deselect Cycle, Power Down
None
X
L
F
Deselect Cycle, Power Down
None
X
L
Read Cycle, Begin Burst
External
R
Read Cycle, Begin Burst
External
Write Cycle, Begin Burst
ADV
W3
DQ4
L
X
X
High-Z
L
X
X
X
High-Z
F
H
L
X
X
High-Z
L
T
L
X
X
X
Q
R
L
T
H
L
X
F
Q
External
W
L
T
H
L
X
T
D
Read Cycle, Continue Burst
Next
CR
X
X
H
H
L
F
Q
Read Cycle, Continue Burst
Next
CR
H
X
X
H
L
F
Q
Write Cycle, Continue Burst
Next
CW
X
X
H
H
L
T
D
Write Cycle, Continue Burst
Next
CW
H
X
X
H
L
T
D
Read Cycle, Suspend Burst
Current
X
X
H
H
H
F
Q
Read Cycle, Suspend Burst
Current
H
X
X
H
H
F
Q
Write Cycle, Suspend Burst
Current
X
X
H
H
H
T
D
Write Cycle, Suspend Burst
Current
H
X
X
H
H
T
D
ADSP ADSC
Notes:
1. X = Don’t Care, H = High, L = Low
2. E = T (True) if E2 = 1 and E3 = 0; E = F (False) if E2 = 0 or E3 = 1
3. W = T (True) and F (False) is defined in the Byte Write Truth Table preceding.
4. G is an asynchronous input. G can be driven high at any time to disable active output drivers. G low can only enable active drivers (shown
as “Q” in the Truth Table above).
5. All input combinations shown above are tested and supported. Input combinations shown in gray boxes need not be used to accomplish
basic synchronous or synchronous burst operations and may be avoided for simplicity.
6. Tying ADSP high and ADSC low allows simple non-burst synchronous operations. See BOLD items above.
7. Tying ADSP high and ADV low while using ADSC to load new addresses allows simple burst operations. See ITALIC items above.
Rev: 1.01 10/2004
9/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Simplified State Diagram
X
Deselect
W
R
Simple Burst Synchronous Operation
Simple Synchronous Operation
W
X
R
R
First Write
CW
First Read
CR
CR
W
X
R
R
X
Burst Write
Burst Read
X
CR
CW
CR
Notes:
1. The diagram shows only supported (tested) synchronous state transitions. The diagram presumes G is tied low.
2. The upper portion of the diagram assumes active use of only the Enable (E1) and Write (BA, BB, BC, BD, BW, and GW) control inputs, and
that ADSP is tied high and ADSC is tied low.
3. The upper and lower portions of the diagram together assume active use of only the Enable, Write, and ADSC control inputs, and
assumes ADSP is tied high and ADV is tied low.
Rev: 1.01 10/2004
10/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Simplified State Diagram with G
X
Deselect
W
R
W
X
R
R
First Write
CR
CW
W
CW
W
X
First Read
X
CR
R
Burst Write
R
CR
CW
W
Burst Read
X
CW
CR
Notes:
1. The diagram shows supported (tested) synchronous state transitions plus supported transitions that depend upon the use of G.
2. Use of “Dummy Reads” (Read Cycles with G High) may be used to make the transition from Read cycles to Write cycles without passing
through a Deselect cycle. Dummy Read cycles increment the address counter just like normal read cycles.
3. Transitions shown in gray tone assume G has been pulsed high long enough to turn the RAM’s drivers off and for incoming data to meet
Data Input Set Up Time.
Rev: 1.01 10/2004
11/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Absolute Maximum Ratings
(All voltages reference to VSS)
Symbol
Description
Value
Unit
VDD
Voltage on VDD Pins
–0.5 to 4.6
V
VDDQ
Voltage in VDDQ Pins
–0.5 to 4.6
V
VI/O
Voltage on I/O Pins
–0.5 to VDDQ +0.5 (≤ 4.6 V max.)
V
VIN
Voltage on Other Input Pins
–0.5 to VDD +0.5 (≤ 4.6 V max.)
V
IIN
Input Current on Any Pin
+/–20
mA
IOUT
Output Current on Any I/O Pin
+/–20
mA
PD
Package Power Dissipation
1.5
W
TSTG
Storage Temperature
–55 to 125
o
TBIAS
Temperature Under Bias
–55 to 125
o
C
C
Note:
Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended
Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of
this component.
Power Supply Voltage Ranges
Parameter
Symbol
Min.
Typ.
Max.
Unit
3.3 V Supply Voltage
VDD3
3.0
3.3
3.6
V
2.5 V Supply Voltage
VDD2
2.3
2.5
2.7
V
3.3 V VDDQ I/O Supply Voltage
VDDQ3
3.0
3.3
3.6
V
2.5 V VDDQ I/O Supply Voltage
VDDQ2
2.3
2.5
2.7
V
Notes
Notes:
1. The part numbers of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device.
2. Input Under/overshoot voltage must be –2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC.
Rev: 1.01 10/2004
12/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
VDDQ3 Range Logic Levels
Parameter
Symbol
Min.
Typ.
Max.
Unit
Notes
VDD Input High Voltage
VIH
2.0
—
VDD + 0.3
V
1
VDD Input Low Voltage
VIL
–0.3
—
0.8
V
1
VDDQ I/O Input High Voltage
VIHQ
2.0
—
VDDQ + 0.3
V
1,3
VDDQ I/O Input Low Voltage
VILQ
–0.3
—
0.8
V
1,3
Notes:
1. The part numbers of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device.
2. Input Under/overshoot voltage must be –2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC.
3. VIHQ (max) is voltage on VDDQ pins plus 0.3 V.
VDDQ2 Range Logic Levels
Parameter
Symbol
Min.
Typ.
Max.
Unit
Notes
VDD Input High Voltage
VIH
0.6*VDD
—
VDD + 0.3
V
1
VDD Input Low Voltage
VIL
–0.3
—
0.3*VDD
V
1
VDDQ I/O Input High Voltage
VIHQ
0.6*VDD
—
VDDQ + 0.3
V
1,3
VDDQ I/O Input Low Voltage
VILQ
–0.3
—
0.3*VDD
V
1,3
Notes:
1. The part numbers of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device.
2. Input Under/overshoot voltage must be –2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC.
3. VIHQ (max) is voltage on VDDQ pins plus 0.3 V.
Recommended Operating Temperatures
Parameter
Symbol
Min.
Typ.
Max.
Unit
Notes
Ambient Temperature (Commercial Range Versions)
TA
0
25
70
°C
2
Ambient Temperature (Industrial Range Versions)
TA
–40
25
85
°C
2
Notes:
1. The part numbers of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device.
2. Input Under/overshoot voltage must be –2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC.
Rev: 1.01 10/2004
13/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Undershoot Measurement and Timing
Overshoot Measurement and Timing
VIH
20% tKC
VDD + 2.0 V
VSS
50%
50%
VDD
VSS – 2.0 V
20% tKC
VIL
Capacitance
(TA = 25oC, f = 1 MHZ, VDD = 2.5 V)
Parameter
Symbol
Test conditions
Typ.
Max.
Unit
Input Capacitance
CIN
VIN = 0 V
4
5
pF
Input/Output Capacitance
CI/O
VOUT = 0 V
6
7
pF
Note:
These parameters are sample tested.
AC Test Conditions
Parameter
Conditions
Input high level
VDD – 0.2 V
Input low level
0.2 V
Input slew rate
1 V/ns
Input reference level
VDDQ/2
Output reference level
VDDQ/2
Output load
Fig. 1
Notes:
1. Include scope and jig capacitance.
2. Test conditions as specified with output loading as shown in Fig. 1
unless otherwise noted.
3. Device is deselected as defined by the Truth Table.
Output Load 1
DQ
50Ω
30pF*
VDDQ/2
* Distributed Test Jig Capacitance
Rev: 1.01 10/2004
14/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
DC Electrical Characteristics
Parameter
Symbol
Test Conditions
Min
Max
Input Leakage Current
(except mode pins)
IIL
VIN = 0 to VDD
–2 uA
2 uA
ZZInput Current
IIN1
VDD ≥ VIN ≥ VIH
0 V ≤ VIN ≤ VIH
–1 uA
–1 uA
1 uA
100 uA
FTInput Current
IIN2
VDD ≥ VIN ≥ VIL
0 V ≤ VIN ≤ VIL
–100 uA
–1 uA
1 uA
1 uA
Output Leakage Current (x36/x72)
IOL
Output Disable, VOUT = 0 to VDD
–1 uA
1 uA
Output Leakage Current (x18)
IOL
Output Disable, VOUT = 0 to VDD
–1 uA
1 uA
Output High Voltage
VOH2
IOH = –8 mA, VDDQ = 2.375 V
1.7 V
—
Output High Voltage
VOH3
IOH = –8 mA, VDDQ = 3.135 V
2.4 V
—
Output Low Voltage
VOL
IOL = 8 mA
—
0.4 V
Rev: 1.01 10/2004
15/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Rev: 1.01 10/2004
300
50
210
25
260
25
190
15
60
IDD
IDDQ
IDD
IDDQ
IDD
IDDQ
IDD
IDDQ
ISB
Pipeline
Flow
Through
Pipeline
IDD
85
100
IDD
Pipeline
Flow
Through
60
ISB
Flow
Through
Flow
Through
Pipeline
0
to
70°C
Symbol
Mode
100
115
80
80
200
15
280
25
220
25
320
50
–40
to
85°C
-250
85
95
60
60
180
15
240
25
200
25
275
45
100
110
80
80
190
15
260
25
210
25
295
45
–40
to
85°C
-225
0
to
70°C
Notes:
1. IDD and IDDQ apply to any combination of VDD3, VDD2, VDDQ3, and VDDQ2 operation.
2. All parameters listed are worst case scenario.
—
Device Deselected;
All other inputs
≥ VIH or ≤ VIL
Deselect
Current
(x18)
—
Operating
Current
ZZ ≥ VDD – 0.2 V
Device Selected;
All other inputs
≥VIH or ≤ VIL
Output open
(x32/
x36)
Standby
Current
Test Conditions
Parameter
Operating Currents
80
90
60
60
170
15
225
20
190
20
255
40
0
to
70°C
95
105
80
80
180
15
245
20
200
20
275
40
–40
to
85°C
-200
80
85
60
60
160
15
200
20
180
20
225
35
0
to
70°C
95
100
80
80
170
15
220
20
190
20
245
35
–40
to
85°C
-166
75
85
60
60
150
15
190
20
170
20
210
30
0
to
70°C
90
100
80
80
160
15
210
20
180
20
230
30
–40
to
85°C
-150
70
80
60
60
140
15
170
15
160
15
190
25
0
to
70°C
85
95
80
80
150
15
190
15
170
15
210
25
–40
to
85°C
-133
mA
mA
mA
mA
mA
mA
mA
mA
Unit
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
16/25
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
AC Electrical Characteristics
Pipeline
Flow
Through
Parameter
Symbol
Clock Cycle Time
-250
-225
-200
-166
-150
-133
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
tKC
4.0
—
4.4
—
5.0
—
6.0
—
6.7
—
7.5
—
ns
Clock to Output Valid
tKQ
—
2.5
—
2.7
—
3.0
—
3.5
—
3.8
—
4.0
ns
Clock to Output Invalid
tKQX
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
Clock to Output in Low-Z
tLZ1
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
Setup time
tS
1.2
—
1.3
—
1.4
—
1.5
—
1.5
—
1.5
—
ns
Hold time
tH
0.2
—
0.3
—
0.4
—
0.5
—
0.5
—
0.5
—
ns
Clock Cycle Time
tKC
5.5
—
6.0
—
6.5
—
7.0
—
7.5
—
8.5
—
ns
Clock to Output Valid
tKQ
—
5.5
—
6.0
—
6.5
—
7.0
—
7.5
—
8.5
ns
Clock to Output Invalid
tKQX
3.0
—
3.0
—
3.0
—
3.0
—
3.0
—
3.0
—
ns
Clock to Output in Low-Z
tLZ1
3.0
—
3.0
—
3.0
—
3.0
—
3.0
—
3.0
—
ns
Setup time
tS
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
Hold time
tH
0.5
—
0.5
—
0.5
—
0.5
—
0.5
—
0.5
—
ns
Clock HIGH Time
tKH
1.3
—
1.3
—
1.3
—
1.3
—
1.5
—
1.7
—
ns
Clock LOW Time
tKL
1.5
—
1.5
—
1.5
—
1.5
—
1.7
—
2
—
ns
Clock to Output in
High-Z
tHZ1
1.5
2.5
1.5
2.7
1.5
3.0
1.5
3.0
1.5
3.0
1.5
3.0
ns
G to Output Valid
tOE
—
2.5
—
2.7
—
3.0
—
3.5
—
3.8
—
4.0
ns
G to output in Low-Z
tOLZ1
0
—
0
—
0
—
0
—
0
—
0
—
ns
G to output in High-Z
tOHZ1
—
2.5
—
2.7
—
3.0
—
3.0
—
3.0
—
3.0
ns
ZZ setup time
tZZS2
5
—
5
—
5
—
5
—
5
—
5
—
ns
ZZ hold time
tZZH2
1
—
1
—
1
—
1
—
1
—
1
—
ns
ZZ recovery
tZZR
20
—
20
—
20
—
20
—
20
—
20
—
ns
Notes:
1. These parameters are sampled and are not 100% tested.
2. ZZ is an asynchronous signal. However, in order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold
times as specified above.
Rev: 1.01 10/2004
17/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Pipeline Mode Timing (DCD)
Begin
Read A
Cont
Deselect Deselect Write B
Read C
Read C+1 Read C+2 Read C+3 Cont
Deselect Deselect
tKL
tKH
tKC
CK
ADSP
tS
ADSC initiated read
tH
ADSC
tS
tH
ADV
tS
tH
Ao–An
A
B
C
tS
GW
tS
tH
BW
tH
tS
Ba–Bd
tS
Deselected with E1
tH
E1
tS
E2 and E3 only sampled with ADSC
tH
E2
tS
tH
E3
G
tS
tOE
DQa–DQd
Hi-Z
Rev: 1.01 10/2004
tOHZ
Q(A)
tKQ
tH
D(B)
tHZ
tLZ
tKQX
Q(C)
Q(C+1)
18/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Q(C+2)
Q(C+3)
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Flow Through Mode Timing (DCD)
Begin
Read A
Cont
Deselect Write B
Read C
Read C+1 Read C+2 Read C+3 Read C
Deselect
tKL
tKH
tKC
CK
ADSP
Fixed High
tS
tH
tS
tH
ADSC
initiated read
ADSC
tH
tS
tS
tH
ADV
tS
tH
Ao–An
A
B
C
tS
tH
GW
tS
tH
BW
tH
tS
Ba–Bd
tS
Deselected with E1
tH
E1 masks ADSP
E1
tS
tH
E2 and E3 only sampled with ADSP and ADSC
E2
tS
tH
E1 masks ADSP
E3
G
tH
tS
tOE
tKQ
DQa–DQd
Rev: 1.01 10/2004
tOHZ
Q(A)
tKQX
tHZ
tLZ
D(B)
Q(C)
Q(C+1)
Q(C+2)
19/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Q(C+3)
Q(C)
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Sleep Mode
During normal operation, ZZ must be pulled low, either by the user or by its internal pull down resistor. When ZZ is pulled high,
the SRAM will enter a Power Sleep mode after 2 cycles. At this time, internal state of the SRAM is preserved. When ZZ returns to
low, the SRAM operates normally after 2 cycles of wake up time.
Sleep mode is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of
Sleep mode is dictated by the length of time the ZZ is in a High state. After entering Sleep mode, all inputs except ZZ become
disabled and all outputs go to High-Z The ZZ pin is an asynchronous, active high input that causes the device to enter Sleep mode.
When the ZZ pin is driven high, ISB2 is guaranteed after the time tZZI is met. Because ZZ is an asynchronous input, pending
operations or operations in progress may not be properly completed if ZZ is asserted. Therefore, Sleep mode must not be initiated
until valid pending operations are completed. Similarly, when exiting Sleep mode during tZZR, only a Deselect or Read commands
may be applied while the SRAM is recovering from Sleep mode.
Sleep Mode Timing Diagram
tKH
tKC
tKL
CK
Setup
Hold
ADSP
ADSC
tZZR
tZZS
tZZH
ZZ
Rev: 1.01 10/2004
20/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
TQFP Package Drawing (Package T)
L
Min. Nom. Max
A1
Standoff
0.05
0.10
0.15
A2
Body Thickness
1.35
1.40
1.45
b
Lead Width
0.20
0.30
0.40
c
Lead Thickness
0.09
—
0.20
D
Terminal Dimension
21.9
22.0
22.1
D1
Package Body
19.9
20.0
20.1
E
Terminal Dimension
15.9
16.0
16.1
E1
Package Body
13.9
14.0
14.1
e
Lead Pitch
—
0.65
—
L
Foot Length
0.45
0.60
0.75
L1
Lead Length
—
1.00
—
Y
Coplanarity
θ
Lead Angle
e
D
D1
Description
c
Pin 1
Symbol
L1
θ
b
A1
A2
0.10
Y
0°
—
7°
E1
E
Notes:
1. All dimensions are in millimeters (mm).
2. Package width and length do not include mold protrusion.
Rev: 1.01 10/2004
21/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Ordering Information for GSI Synchronous Burst RAMs
Org
Part Number1
Type
Package
Speed2
(MHz/ns)
TA3
2M x 18
GS8320E18T-250
Pipeline/Flow Through
TQFP
250/6.5
C
2M x 18
GS8320E18T-225
Pipeline/Flow Through
TQFP
225/7
C
2M x 18
GS8320E18T-200
Pipeline/Flow Through
TQFP
200/7.5
C
2M x 18
GS8320E18T-166
Pipeline/Flow Through
TQFP
166/8
C
2M x 18
GS8320E18T-150
Pipeline/Flow Through
TQFP
150/8.5
C
2M x 18
GS8320E18T-133
Pipeline/Flow Through
TQFP
133/8.5
C
1M x 32
GS8320E32T-250
Pipeline/Flow Through
TQFP
250/6.5
C
1M x 32
GS8320E32T-225
Pipeline/Flow Through
TQFP
225/7
C
1M x 32
GS8320E32T-200
Pipeline/Flow Through
TQFP
200/7.5
C
1M x 32
GS8320E32T-166
Pipeline/Flow Through
TQFP
166/8
C
1M x 32
GS8320E32T-150
Pipeline/Flow Through
TQFP
150/8.5
C
1M x 32
GS8320E32T-133
Pipeline/Flow Through
TQFP
133/8.5
C
1M x 36
GS8320E36T-250
Pipeline/Flow Through
TQFP
250/6.5
C
1M x 36
GS8320E36T-225
Pipeline/Flow Through
TQFP
225/7
C
1M x 36
GS8320E36T-200
Pipeline/Flow Through
TQFP
200/7.5
C
1M x 36
GS8320E36T-166
Pipeline/Flow Through
TQFP
166/8
C
1M x 36
GS8320E36T-150
Pipeline/Flow Through
TQFP
150/8.5
C
1M x 36
GS8320E36T-133
Pipeline/Flow Through
TQFP
133/8.5
C
2M x 18
GS8320E18T-250I
Pipeline/Flow Through
TQFP
250/6.5
I
2M x 18
GS8320E18T-225I
Pipeline/Flow Through
TQFP
225/7
I
2M x 18
GS8320E18T-200I
Pipeline/Flow Through
TQFP
200/7.5
I
2M x 18
GS8320E18T-166I
Pipeline/Flow Through
TQFP
166/8
I
2M x 18
GS8320E18T-150I
Pipeline/Flow Through
TQFP
150/8.5
I
2M x 18
GS8320E18T-133I
Pipeline/Flow Through
TQFP
133/8.5
I
1M x 32
GS8320E32T-250I
Pipeline/Flow Through
TQFP
250/6.5
I
1M x 32
GS8320E32T-225I
Pipeline/Flow Through
TQFP
225/7
I
1M x 32
GS8320E32T-200I
Pipeline/Flow Through
TQFP
200/7.5
I
1M x 32
GS8320E32T-166I
Pipeline/Flow Through
TQFP
166/8
I
Status
1M x 32
GS8320E32T-150I
Pipeline/Flow Through
TQFP
150/8.5
I
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS8320E18T-150IT.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow Through mode-selectable by the user.
3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range.
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.01 10/2004
22/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Ordering Information for GSI Synchronous Burst RAMs
Org
Part Number1
Type
Package
Speed2
(MHz/ns)
TA3
1M x 32
GS8320E32T-133I
Pipeline/Flow Through
TQFP
133/8.5
I
1M x 36
GS8320E36T-250I
Pipeline/Flow Through
TQFP
250/6.5
I
1M x 36
GS8320E36T-225I
Pipeline/Flow Through
TQFP
225/7
I
1M x 36
GS8320E36T-200I
Pipeline/Flow Through
TQFP
200/7.5
I
1M x 36
GS8320E36T-166I
Pipeline/Flow Through
TQFP
166/8
I
1M x 36
GS8320E36T-150I
Pipeline/Flow Through
TQFP
150/8.5
I
1M x 36
GS8320E36T-133I
Pipeline/Flow Through
TQFP
133/8.5
I
2M x 18
GS8320E18GT-250
Pipeline/Flow Through
Pb-free TQFP
250/6.5
C
2M x 18
GS8320E18GT-225
Pipeline/Flow Through
Pb-free TQFP
225/7
C
2M x 18
GS8320E18GT-200
Pipeline/Flow Through
Pb-free TQFP
200/7.5
C
2M x 18
GS8320E18GT-166
Pipeline/Flow Through
Pb-free TQFP
166/8
C
2M x 18
GS8320E18GT-150
Pipeline/Flow Through
Pb-free TQFP
150/8.5
C
2M x 18
GS8320E18GT-133
Pipeline/Flow Through
Pb-free TQFP
133/8.5
C
1M x 32
GS8320E32GT-250
Pipeline/Flow Through
Pb-free TQFP
250/6.5
C
1M x 32
GS8320E32GT-225
Pipeline/Flow Through
Pb-free TQFP
225/7
C
1M x 32
GS8320E32GT-200
Pipeline/Flow Through
Pb-free TQFP
200/7.5
C
1M x 32
GS8320E32GT-166
Pipeline/Flow Through
Pb-free TQFP
166/8
C
1M x 32
GS8320E32GT-150
Pipeline/Flow Through
Pb-free TQFP
150/8.5
C
1M x 32
GS8320E32GT-133
Pipeline/Flow Through
Pb-free TQFP
133/8.5
C
1M x 36
GS8320E36GT-250
Pipeline/Flow Through
Pb-free TQFP
250/6.5
C
1M x 36
GS8320E36GT-225
Pipeline/Flow Through
Pb-free TQFP
225/7
C
1M x 36
GS8320E36GT-200
Pipeline/Flow Through
Pb-free TQFP
200/7.5
C
1M x 36
GS8320E36GT-166
Pipeline/Flow Through
Pb-free TQFP
166/8
C
1M x 36
GS8320E36GT-150
Pipeline/Flow Through
Pb-free TQFP
150/8.5
C
1M x 36
GS8320E36GT-133
Pipeline/Flow Through
Pb-free TQFP
133/8.5
C
2M x 18
GS8320E18GT-250I
Pipeline/Flow Through
Pb-free TQFP
250/6.5
I
2M x 18
GS8320E18GT-225I
Pipeline/Flow Through
Pb-free TQFP
225/7
I
2M x 18
GS8320E18GT-200I
Pipeline/Flow Through
Pb-free TQFP
200/7.5
I
2M x 18
GS8320E18GT-166I
Pipeline/Flow Through
Pb-free TQFP
166/8
I
2M x 18
GS8320E18GT-150I
Pipeline/Flow Through
Pb-free TQFP
150/8.5
I
Status
2M x 18
GS8320E18GT-133I
Pipeline/Flow Through
Pb-free TQFP
133/8.5
I
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS8320E18T-150IT.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow Through mode-selectable by the user.
3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range.
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.01 10/2004
23/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
Ordering Information for GSI Synchronous Burst RAMs
Org
Part Number1
Type
Package
Speed2
(MHz/ns)
TA3
1M x 32
GS8320E32GT-250I
Pipeline/Flow Through
Pb-free TQFP
250/6.5
I
1M x 32
GS8320E32GT-225I
Pipeline/Flow Through
Pb-free TQFP
225/7
I
1M x 32
GS8320E32GT-200I
Pipeline/Flow Through
Pb-free TQFP
200/7.5
I
1M x 32
GS8320E32GT-166I
Pipeline/Flow Through
Pb-free TQFP
166/8
I
1M x 32
GS8320E32GT-150I
Pipeline/Flow Through
Pb-free TQFP
150/8.5
I
1M x 32
GS8320E32GT-133I
Pipeline/Flow Through
Pb-free TQFP
133/8.5
I
1M x 36
GS8320E36GT-250I
Pipeline/Flow Through
Pb-free TQFP
250/6.5
I
1M x 36
GS8320E36GT-225I
Pipeline/Flow Through
Pb-free TQFP
225/7
I
1M x 36
GS8320E36GT-200I
Pipeline/Flow Through
Pb-free TQFP
200/7.5
I
1M x 36
GS8320E36GT-166I
Pipeline/Flow Through
Pb-free TQFP
166/8
I
1M x 36
GS8320E36GT-150I
Pipeline/Flow Through
Pb-free TQFP
150/8.5
I
Status
1M x 36
GS8320E36GT-133I
Pipeline/Flow Through
Pb-free TQFP
133/8.5
I
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS8320E18T-150IT.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow Through mode-selectable by the user.
3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range.
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.01 10/2004
24/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
Preliminary
GS8320E18/32/36T-250/225/200/166/150/133
36Mb Sync SRAM Datasheet Revision History
DS/DateRev. Code: Old;
New
Types of Changes
Format or Content
• Creation of new datasheet
8320E18_r1
8320E18_r1;
8320E18_r1_01
Rev: 1.01 10/2004
Page;Revisions;Reason
Content/Format
• Updated format
• Added Pb-free information for TQFP package
25/25
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology