MICREL MIC2185BQS

MIC2185
Micrel, Inc.
MIC2185
Low Voltage Synchronous Boost PWM Control IC
General Description
Features
Micrel’s MIC2185 is a high efficiency synchronous boost
PWM control IC. With its wide input voltage range of 2.9V to
14V, the MIC2185 can be used to efficiently boost voltages
in 1- or 2-cell Li Ion battery powered applications, as well as
fixed 3.3V and 5V systems. Its powerful 5Ω output drivers
allow the MIC2185 to supply large output currents with the
selection of the proper external MOSFETs.
With it’s fixed frequency PWM architecture, and easily
synchronized drive, the MIC2185 is ideal for noise-sensitive telecommunications applications. The nominal 400kHz
operating frequency of the MIC2185 can be divided by two,
allowing the device to be externally synchronized to frequencies below 400kHz.
The MIC2185 also features a low current shutdown mode
and a programmable undervoltage lockout. A skipped pulse
mode of operation can be manually set to achieve higher
efficiencies at light load conditions.
The MIC2185 is available in a 16 pin SOIC package and 16
pin QSOP package with an ambient temperature operating
range from –40°C to 85°C.
•
•
•
•
•
•
•
•
•
•
•
•
•
Input voltage range: 2.9V to 14V
95% efficiency
Oscillator frequency of 200kHz/400kHz
Frequency sync to 600kHz
0.5µA shutdown current
Two 5Ω output drivers
Front edge blanking
PWM current mode control
Cycle-by-cycle current limiting
Frequency foldback protection
Adjustable under-voltage lockout
Precision 1.245V reference output
16 pin SOIC narrow body package
Applications
•
•
•
•
3.3V to 5V conversion in telecom systems
Satellite phones
Cable modems
1-and 2-cell Li Ion battery operated equipment
Ordering Information
Part Number
Typical Application
Voltage
Junction
Temp. Range
Package
MIC2185YM
200/400kHz
Adj
–40ºC to +125ºC
16-pin SOIC
MIC2185YQS
200/400kHz
Adj
–40ºC to +125ºC
16-pin QSOP
Pb-Free
MIC2185BM
MIC2185BQS
2.4µH
VIN = 3.3V
Frequency
Standard
Si9803DY (x2)
VOUT = 5V
CIN
1
7
VINA
OUTP
EN/UVLO
15
FREQ/2
10
VDD
4
COMP
8
VREF
11
2
VINP
FB
MIC2185
OUTN
CSH
14
COUT
16
6
13
100
Si4884DY (x2)
85
8m
SKIP
SS
3
PGND
SGND
95
90
9
SYNC
5V Output Efficiency
12
80
75
5
70
0
VIN = 3.3V
200kHz P WM
1
2
3
4
5
OUTPUT CURRENT (A)
Adjustable Output Synchronous Boost Converter
Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
October 2005
1
MIC2185
MIC2185
Micrel, Inc.
Pin Configuration
VINA 1
16 VINP
SKIP 2
15 FREQ/2
SS 3
14 OUTP
COMP 4
13 OUTN
SGND 5
12 PGND
FB 6
11 SYNC
EN/UVLO 7
10 VDD
VREF 8
9 CSH
16-pin Narrow Body SOIC (M)
16-pin QSOP (QS)
Pin Description
Pin Number
Pin Name
MIC2185
Pin Function
1
VINA
Input voltage to control circuitry (2.9V to 14V).
2
SKIP
Skip (Input): Regulator operates in PWM mode (no pulse skipping) when
pin is pulled low, and skip mode when raised to VDD. There is no automatic
switching between PWM and skip mode available on this device.
3
SS
Soft Start (External Component) : Reduces the inrush current and delays
and slows the output voltage rise time. A 5µA current source will charge the
capacitor up to VDD.
4
COMP
Compensation (Output): Internal error amplifier output. Connect to a capacitor or series RC network to compensate the regulator’s control loop.
5
SGND
Small Signal Ground (Return) : Must be routed separately from other
grounds to the (–) terminal of COUT.
6
FB
7
EN/UVLO
Feedback (Input) : Regulates FB to 1.245V.
8
VREF
Voltage Reference (Output) : The 1.245V reference is available on this pin.
A 0.1µF capacitor should be connected form this pin to SGnd.
9
CSH
Current Sense (Input) : The (+) input to the current limit comparator. A built
in offset of 100mV (typical) between CSH and SGnd in conjunction with the
current sense resistor sets the current limit threshold level. This is also the
(+) input to the current amplifier.
10
VDD
3V Internal Linear-Regulator (Output) : VDD is also the supply voltage bus
for the chip. Bypass to SGND with 1µF. Maximum source current is 0.5mA.
11
SYNC
Frequency Synchronization (Input): Connect an external clock signal to
synchronize the oscillator. Leading edge of signal above 1.4V (typical) starts
switching cycle. Connect to SGND if not used.
12
PGND
13
OUTN
MOSFET Driver Power Ground (Return) : Connects bottom of current sense
resistor and the (–) terminal of CIN.
14
OUTP
15
FREQ/2
16
VINP
Enable/Undervoltaqe Lockout (Input): A low level on this pin will power down
the device, reducing the quiescent current to under 0.5µA. This pin has two
separate thresholds, below 1.5V (typical) the output switching is disabled,
and below 0.9V (typical) the device is forced into a complete micropower
shutdown. The 1.5V threshold functions as an accurate undervoltage lockout
(UVLO) with 140mV hysteresis.
N-Channel Drive (Output) : High current drive for n-channel MOSFET. Voltage swing is from ground to VINP. On-resistance is typically 5Ω.
P-Channel Drive (Output) : High current drive for the synchronous p-channel
MOSFET. Voltage swing is from ground to VINP. On-resistance is typically
5Ω.
Frequency Divider (Input) : When this pin is low, the oscillator frequency is
400KHz. When this pin is raised to VDD, the oscillator frequency is 200KHz.
Gate Drive Voltage (Input) : This is the power input to the gate drive circuitry (2.9V to 14V). This pin is typically connected to the output voltage to
enhance gate drive.
2
October 2005
MIC2185
Micrel, Inc.
Absolute Maximum Ratings (Note 1)
Operating Ratings (Note 2)
Supply Voltage (VINA, VINP) .......................................... 15V
Digital Supply Voltage (VDD)............................................ 7V
Skip Pin Voltage (VSKIP) ....................................–0.3V to 7V
Comp Pin Voltage (VCOMP) ...............................–0.3V to 3V
Feedback Pin Voltage (VFB) ..............................–0.3V to 3V
Enable Pin Voltage (VEN/UVLO) .......................–0.3V to 15V
Current Sense Voltage (VCSH) ..........................–0.3V to 1V
Sync Pin Voltage (VSYNC) ................................–0.3V to 7V
Freq/2 Pin Voltage (VFREQ/2) .............................–0.3V to 7V
Power Dissipation (PD)
16 lead SOP ...................................400mW @ TA = 85°C
16 lead QSOP .................................245mW@ TA = 85°C
Ambient Storage Temp ............................. –65°C to +150°C
Supply Voltage (VINA, VINP) ......................... +2.9V to +14V
Operating Ambient Temperature...........–40°C ≤ TA ≤ +85°C
Junction Temperature .........................–40°C ≤ TJ ≤ +125°C
PackageThermal Resistance
θJA 16-lead SOP ................................................ 100°C/W
θJA 16-lead QSOP ............................................. 163°C/W
ESD Rating, Note 3
Electrical Characteristics
VINA= 5V, VinP= VOUT=12V, VEN/UVLO = 5V, VSKIP = 0V, VFREQ/2 = 0V, VCSH = 0V, TJ = 25°C, unless otherwise specified. Bold values
indicate –40°C < TJ < +125°C.
Parameter
Condition
Min
Typ
Max
Units
(±1%)
1.233
1.245
1.258
V
(±2%)
1.220
1.270
V
3V ≤ VINA ≤ 9V; 0mV ≤ CSH ≤ 75mV; (±3%)
1.208
1.282
V
Regulation
Feedback Voltage Reference
Feedback Bias Current
1.245
50
nA
+0.08
%/V
0mV ≤ CSH ≤ 75mV
–1.2
%
VINA Input Current, PWM mode
VSKIP = 0V
VINA Input Current, SKIP mode
VSKIP = 5V
Output Voltage Line Regulation
Output Voltage Load Regulation
Input & VDD Supply
VINP Input Current, PWM mode
Shutdown Quiescent Current
Digital Supply Voltage (VDD)
Digital Supply Load Regulation
Undervoltage Lockout
Reference Output (VREF)
Reference Voltage
3V ≤ VINA ≤ 9V
0.8
mA
VSKIP = 0V (excluding external MOSFET gate current)
3.8
mA
0.6
mA
VEN/UVLO = 0V; (IVINA + IVINP)
0.5
µA
IL = 0
2.8
VDD upper threshold (turn on threshold)
2.9
IL = 0 to 0.5mA
VDD lower threshold (turn off threshold)
(±1.5%)
1.226
(±2.5%)
1.213
3.0
3.2
V
0.03
V
2.75
V
2.65
V
1.245
1.264
1.276
V
V
Reference Voltage Line
Regulation
5V < VinA < 9V
2
mV
Reference Voltage Load
Regulation
0 < IREF < 100µA
1
mV
Enable/UVLO
Enable Input Threshold
0.6
UVLO Threshold
1.4
UVLO Hysteresis
Enable Input Current
October 2005
0.9
1.2
1.5
1.6
140
VEN/UVLO = 5V
0.2
3
V
V
mV
5
µA
MIC2185
MIC2185
Parameter
Micrel, Inc.
Condition
Min
Typ
Max
Unit
Soft Start
Soft Start Current
5
µA
100
mV
20
V/V
3.7
V/V
Current Limit
Current Limit Threshold Voltage
Voltage on CSH to trip current limit
Error Amplifier
Error Amplifier Gain
Current Amplifier
Current Amplifier Gain
SKIP Input
SKIP Threshold
SKIP Input Current
Oscillator Section
Oscillator Frequency (fS)
Maximum Duty Cycle
Minimum On Time
FREQ/2 frequency (fS)
0.6
VSKIP = 3V
360
VFB = 1.0V
1.4
2.2
V
0.1
5
µA
400
440
kHz
85
VFB = 1.5V
%
180
VFREQ/2=3V
170
200
ns
230
Frequency Foldback Threshold
Measured at FB pin
0.3
V
Frequency Foldback Frequency
VFREQ/2=0V
90
kHz
SYNC Threshold Level
0.6
SYNC Input Current
SYNC Minimum Pulse Width
SYNC Capture Range
Driver Non-overlap Time
Output Driver Impedance
V
5
µA
600
kHz
ns
fO+15 %
CL = 3300pF
50
ns
VINP = 12V
70
ns
VINP = 5V
90
ns
Source; VINP = 12V
4
8
Ω
Sink; VINP = 12V
3
7
Ω
Source; VINP = 5V
5
11
Ω
5
11
Ω
Sink; VINP = 5V
Note 1.
2.2
0.1
200
Note 4
Gate Drivers (OUTN and OUTP)
Rise/Fall Time
1.4
Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when
operating the device outside of its operating ratings. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(max), the junction-to-ambient thermal resistance, θJA, and the ambient temperature, TA.
Note 2.
The device is not guaranteed to function outside its operating rating.
Note 3.
Devices are ESD sensitive. Handling precautions recommended.
Note 4.
See application information for limitations on maximum operating frequency.
MIC2185
4
October 2005
MIC2185
Micrel, Inc.
Typical Characteristics
4.75
0.7
4.70
0.6
4.65
VINP = 5V
1.0
IQ = IQVINA + IQVINP
0.5 f = 400kHz
S
0
0 2 4 6 8 10 12 14 16
INPUT VOLTAGE (VINA )
Reference Voltage
vs. Reference Current
1.2469
1.2468
3.035
VDD vs.
Load Current
VINP = 12VDC
VINA = 5VDC
3.030
3.025
3.020
3.015
3.010
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
IVDD (mA)
October 2005
0.60
0.55
0
120
140
60
80
100
VINP = 9VDC
1.246
1.2455
VINP = 5VDC
1.257
1.255
2 4 6 8 10 12 14 16
INPUT VOLTAGE (VINA )
Reference Voltage
vs. Temperature
1.245
0
2 4 6 8 10 12 14 16
INPUT VOLTAGE (VINA)
VDD vs.
Input Voltage
3.15
VINP = 12VDC
VINA = 5VDC
3.10
3.05
1.249
1.247
3.00
1.245
1.243
1.241
1.239
2.95
2.90
1.237
-40 -20 0 20 40 60 80 100120140
TEMPERATURE(°C)
2.80
0
2.85
VDD vs.
Temperature
3.08
V P = 12VDC
3.07 IN
3.06 VINA = 5VDC
3.05
3.04
3.03
3.02
3.01
3.00
2.99
2.98
300
VINP = 12VDC
2
4
6 8 10 12
INPUT VOLTAGE (VINA)
14
IENABLE vs. VENABLE
VINP = 12VDC
–40°C
250 VINA = 5VDC
200
150
20°C
100
85°C
50
40
60
80
100
1.2463
1.2462 V P = 12V
IN
DC
1.2461 V A = 5V
IN
DC
1.2460
0 10 20 30 40 50 60 70 80 90 100
REFERENCE CURRENT (µA)
3.040
0.65
-60
1.2465
1.2464
VINP = 12VDC
1.2465
0.70
1.253
1.251
1.2467
1.2466
1.2475
Reference Voltage
vs. Input Voltage
1.247
VINP = 12VDC
TEMPERATURE (°C)
5
140
VINP = 9V
2.5
2.0
1.5
1.0 V P =12V
IN
DC
0.5 IQ = IQVINA+IQVINP
0
0 2 4 6 8 10 12 14 16
INPUT VOLTAGE (VINA )
0.80
0.75
3.5
3.0
20
40
Quiescent Current vs.
Input Voltage (SKIP Mode)
120
VINP = 12V
200kHz
2.0
1.5
TEMPERATURE (°C)
Quiescent Current vs.
Input Voltage( PWM Mode)
4.5
4.0
-20
0
0
-40 -20 0 20 40 60 80 100120140
TEMPERATURE (°C)
-40
0.1
4.45 VINA = 5VDC
V P = 12VDC
4.40 IN
fS = 400kHz
4.35 I = I
+I
Q
QVINA QVINP
4.30
-60
VINA = 5VDC
VINP = 12VDC
IQ = IQVINA+IQVINP
0.2
1.2470
3.5
4.50
0.3
400kHz
3.0
2.5
4.55
0.4
5.0
4.5
Quiescent Current vs.
Input Voltage(PWM Mode)
4.0
4.60
0.5
5.0
Quiescent Current vs.
Temperature (PWM Mode)
-40
-20
0
20
0.8
Quiescent Current vs.
Temperature (SKIP Mode)
0
0
2
4
6 8 10
VENABLE (V)
12
14
MIC2185
MIC2185
Micrel, Inc.
5.00
405
4.95
4.90
120
VINP = 12VDC
4.85
4.80
VINA = 5VDC
TEMPERATURE (°C)
130
130
90
TEMPERATURE(°C)
110
70
50
30
10
-10
390
-30
14
-50
2
4
6 8 10 12
INPUT VOLTAGE (VINA)
VINA = 5VDC
90
VINP = 12VDC
395
110
400
413
412
0
410
70
415
414
5.05
50
417
416
5.10
415
30
418
420
10
420
419
5.15
-10
425
Soft Start Current
vs. Temperature
-30
422
V P = 12VDC
421 IN
Oscillator Frequency
vs. Temperature
-50
Oscillator Frequency
vs. Input Voltage
Overcurrent Threshold
vs. VINA
100
80
60
40
VINP = 12VDC
20
0
0
MIC2185
2
4
6 8 10 12 14 16
VINA (V)
6
October 2005
MIC2185
Micrel, Inc.
Functional Diagram
VIN
CIN
L1
CDECOUP
1
VINA
VINP
EN/UVLO
Bias
7
16
VREF
VDD
Q2
On
SKIP
2
14
Control
fs/4
15
11
COUT
PGND
OUTN
Reset
FREQ/2
VOUT
OUTP
Overcurrent Reset
SYNC
D1
13
Osc
0.1V
PWM
Comparator
Q1
PGND
Correction
Ramp
Overcurrent
Comparator
SS
3
CSH
9
Gain = 3.7
Error
Amplifier
COMP
RSENSE
VREF
PGND
gm = 0.0002
Gain = 20
4
100k
PGND
12
0.3V
fs/4
VREF
8
VDD
10
R1
FB
VREF
6
Frequency
Foldback
VDD
R2
SGND
SGND
5
Figure 1. MIC2185 PWM Mode Block Diagram
Functional Description
starts when OutN goes high and turns on the low side, Nchannel MOSFET, Q1. The Vgs of the MOSFET is equal to
VinP. This forces current to ramp up in the inductor. The
inductor current flows through the current sense resistor,
Rsense. The voltage across the resistor is amplified and
combined with an internal ramp for stability. This signal is
compared with the comp output signal of the error amplifier.
When the current signal equals the error voltage signal, the
low side MOSFET is turned off. The inductor current then
flows through the diode, D1, to the output. A delay between
the turn-off of the low side MOSFET and the turn-on of the
high side MOSFET prevents both MOSFETs from being on
at the same time, which would short the output to ground.
At the end of the non-overlap time, OutP pulls the gate of
the MOSFET to ground, turning on the high side, P-channel
The MIC2185 is a BiCMOS, switched mode, synchronous
boost (step up) control IC. The synchronous switched, high
side P-channel MOSFET, Q2, placed in parallel with the output diode, D1, improves the efficiency of the boost converter.
The lower voltage drop across the MOSFET reduces power
dissipation and increases efficiency. Current mode control is
used to achieve superior transient line and load regulation.
An internal corrective ramp provides slope compensation
for stable operation above a 50% duty cycle. The controller
is optimized for high efficiency, high performance DC-DC
converter applications.
Figure 1 is a block diagram of the MIC2185 configured as
a PWM synchronous boost converter. The switching cycle
October 2005
7
MIC2185
MIC2185
Micrel, Inc.
Control Loop
PWM and SKIP modes of operation
The MIC2185 can operate in either PWM (pulse width modulated) or skip mode. The efficiency of the boost converter can
be improved at lower output loads by manually selecting the
skip mode of operation. The potential disadvantage of skip
mode is the variable switching frequency that accompanies
this mode of operation. The occurrence of switching pulses
depends on component values as well as line and load conditions. PWM mode is the best choice of operation at higher
output loads. In skip mode, current through the inductor can
settle to zero, causing voltage ringing across the inductor.
PWM mode has the advantages of lower output ripple voltage and higher efficiencies at higher output loads. Another
advantage of the synchronous PWM mode of operation is
that the inductor current is always continuous, even at zero
output current. This reduces parasitic ringing that occurs
MOSFET, Q2. Current flows through the MOSFET because
its voltage drop is less than diode D1. The MOSFET remains
on until the end of the switching cycle. There is another
non-overlap time delay between the turn-off of the high side
MOSFET and the turn-on of the low side MOSFET at the
beginning of the next switching cycle.
The description of the MIC2185 controller is broken down
into 6 basic functions.
• Control Loop
• PWM Operation
• SKIP Mode Operation
• Current Limit
• MOSFET gate drive
• Reference, Enable & UVLO
• Oscillator & Sync
• Soft Start
VIN
CIN
CDECOUP
L1
VINA 1
VINP
EN/UVLO
Bias
7
16
VREF
Q2
On
VDD
SKIP
VOUT
OUTP
14
Control
2
D1
VDD
COUT
PGND
OUTN
13
50mV
FREQ/2
Q1
PGND
15
Osc
Current Reset
CSH
SYNC
11
9
Skip Current
Limit Comparator
SS
3
RSENSE
PGND
COMP
4
PGND
12
VREF
1.245V
VREF
8
VDD
10
R1
FB
VREF
6
Hysteresis
Comparator
1%
VDD
R2
SGND
SGND
5
Figure 2. MIC2185 Skip Mode Block Diagram
MIC2185
8
October 2005
MIC2185
Micrel, Inc.
during the discontinuous mode of operation found in lightly
loaded, non-synchronous boost converters. Pulling the SKIP
pin (pin 2) low will force the controller to operate in PWM
mode for all load conditions. Pulling the SKIP pin high will
force the controller to operate in SKIP mode.
Skip Mode Operation
This control method is used to improve efficiency at low output
loads. A block diagram of the MIC2185 skip mode is shown
in Figure 2. The power drawn by the MIC2185 control IC is
(IVINA · VVINA) + (IVINP · VVINP). The power dissipated by the
IC can be a significant portion of the total output power during
periods of low output current, which lowers the efficiency of
the power supply. In skip mode the MIC2185 lowers the IC
supply current by disabling the high side drive and running
at lower than the PWM switching frequency. It also turns off
portions of the control and drive circuitry when the IC is not
switching. The disadvantage of this method is greater output
ripple and variable switching frequency. The Soft Start and
Sync pins have no effect when operating in skip mode.
Once the voltage on the feedback pin exceeds the upper
hysteretic threshold the gate drive is disabled. The output
load discharges the output capacitance causing Vout to
decrease until the feedback voltage drops below the lower
threshold voltage limit. The switching converter then turns
the gate drive back on. While the gate drive is disabled, the
MIC2185 draws less IC supply current then while it is switching, thereby improving efficiency at low output loads.
Figure 4 shows the improvement in efficiency that SKIP mode
makes when at lower output currents.
100
80
PWM
400kHz
60
SKIP
40
20
VIN=3.3V
VOUT=5V
0
0.02
0.04
0.06
0.08
0.1
0
0.12
0.14
0.16
0.18
0.20
In skip mode, switching starts when the feedback voltage
drops below the lower threshold level of the hysteresis comparator. The OutN pin goes high, turning on the N-channel
MOSFET, Q1. Current ramps up in the inductor until either
the SKIP mode current limit comparator or the hysteretic
voltage comparator turns off Q1’s gate drive. If the feedback
voltage exceeds the upper hysteretic threshold, Q1’s gate
drive is terminated. Or, if the voltage at the CSH pin exceeds
the skip mode current limit threshold, it terminates the gate
drive for that switching cycle. The gate drive remains off for
a constant period at the end of each switching cycle. This
off time period is typically 1us when the F/2 pin is low and
2us when the F/2 pin is high. Figure 3 shows some typical
switching waveforms in SKIP mode.
OUTPUT CURRENT (A)
Figure 4.
The maximum peak inductor current depends on the skip
current limit threshold and the value of the current sense
resistor, RSENSE. For a typical 50mV current limit threshold
in skip mode, the peak inductor current is:
50mV
IINDUCTOR_pk =
RSENSE
The maximum output current in skip mode depends on the
input conditions, output conditions and circuit component
values. Assuming a discontinuous mode where the inductor
current starts from zero at each cycle, the maximum output
current is calculated below:
SKIP Mode Waveform
Switch NodeVoltage
(Low Side FET Drain)
5V/div
IO(max)=
Low Side FET
Gate Drive
5V/div
2.5 × 10 −3 × L × fs
2 × RSENSE 2 × VO − ( η × VIN )
(
)
where: IO(max) is the maximum output current
VOUT RippleVoltage
200mV/div
VO is the output voltage
VIN is the input voltage
L is the value of the boost inductor
fS is the switching frequency
η is the efficiency of the boost converter
RSENSE is the value of the current sense resistor
2.5·10-3 is a constant based on the skip mode
current threshold (50mV)2
Inductor Current
5A/div
VIN = 3.3V
VOUT = 9V IOUT = 0.55A
TIME (50µs/div)
Figure 3. SKIP mode waveforms
The skip mode current threshold limits the peak inductor
current per cycle. Depending on the input, output and circuit
parameters, many switching cycles can occur before the
feedback voltage exceeds the upper hysteretic threshold.
October 2005
MIC2185 PWM vs.
Skip Mode Efficiency
9
MIC2185
MIC2185
Micrel, Inc.
PWM Operation
VIN = 3.3V
Switch NodeVoltage
(Low Side FET Drain)
5V/div
required in current mode control to prevent unstable operation
at duty cycles greater than 50%.
A transconductance amplifier is used as an error amplifier,
which compares an attenuated output voltage with a reference voltage. The output of the error amplifier is compared
to the current sense waveform in the PWM block. When the
current signal rises above the error voltage, the comparator
turns off the low side drive. The error signal is brought out to
the COMP pin (pin 4) allowing the use of external components
to stabilize the voltage loop.
Current Sensing and Overcurrent Protection
The inductor current is sensed during the switch on time by
a current sense resistor located between the source of the
MOSFET, Q1 and ground (RSENSE in Figure 1). Exceeding
the current limit threshold will immediately terminate the
gate drive of the N-channel MOSFET. This forces the Q1 to
operate at a reduced duty cycle, which reduces the output
voltage. In a boost converter, the overcurrent limit will
not protect the power supply or load during a severe
overcurrent condition or short circuit condition. If the
output is short-circuited to ground, current will flow from the
input, through the inductor and output diode,D1, to ground.
Only the impedance of the source and components limits
the current.
The minimum input voltage, maximum output power and
the minimum value of the current limit threshold determine
the value of the current sense resistor. The two switch, synchronous operation of the MIC2185 forces the converter to
always operate in the continuous mode because current can
flow both ways through the high side P-channel MOSFET.
The equations below will help to determine the current sense
resistor value.
Maximum Peak Current
The peak inductor current is equal to the average inductor
current plus one half of the peak to peak inductor current.
The peak inductor current is:
1
IIND(pk)= IIND(ave) + × IIND(pp)
2
PWM ModeWaveform
VOUT = 5V
IOUT = 0.75A
High Side FET
Gate Drive
5V/div
Low Side FET
Gate Drive
5V/div
Inductor Current
1A offset; 0.5A/div
VOUT RippleVoltage
200mV/div
TIME (1µs/div)
Figure 5 - PWM mode waveforms
Figure 5 shows typical waveforms for PWM mode of operation.
The gate drive signal turns on the external low side MOSFET,
Q1, allowing the inductor current to ramp up. When the low
side MOSFET turns off and the high side MOSFET, Q2, turns
on, current flowing in the inductor forces the MOSFET drain
voltage to rise until the is clamped at approximately the output
voltage. The MIC2185 uses current mode control to improve
output regulation and simplify compensation of the control
loop. Current mode control senses both the output voltage
(outer loop) and the inductor current (inner loop). It uses the
inductor current and output voltage to determine the duty
cycle (D) of the buck converter. Sampling the inductor current
effectively removes the inductor from the control loop, which
simplifies compensation. A simplified current mode control
diagram is shown in figure 6.
I_inductor
VIN
Voltage
Divider
I_inductor
Gate Driver
I_inductor
IIND(pk)=
VREF
)
where:
IO is the maximum output current
VO is the output voltage
VIN is the minimum input voltage
L is the value of the boost inductor
fS is the switching frequency
η is the efficiency of the boost converter
VL is the voltage across the inductor
VL may be approximated as VIN for higher input voltage.
However, the voltage drop across the inductor winding
resistance and low side MOSFET on-resistance must be
accounted for at the lower input voltages that the MIC2185
can operate at:
I_inductor
VCOMP
Gate Drive at OUTN
TON
TPER
Figure 6. PWM Control Loop
A block diagram of the MIC2185 PWM current mode control
loop is shown in Figure 1. The inductor current is sensed by
measuring the voltage across a resistor, Rsense. The current
sense amplifier buffers and amplifies this signal. A ramp is
added to this signal to provide slope compensation, which is
MIC2185
(
VO × IO VL × VO − (VIN × η)
+
VIN × η
2 × VO × fs × L
10
October 2005
MIC2185
VL = VIN −
Micrel, Inc.
VO × IO
× R WINDING + RDS(ON)
VIN × η
(
may cause MOSFETs with lower gate thresholds to erroneously turn on.
There is a limit to the maximum amount of gate charge the
MIC2185 will drive. Higher gate charge will slow down the
turn-on and turn-off times of the MOSFETs. The MOSFET’s
must be able to completely turn on and off within the driver
non-overlap time or shoot-through will occur.
MOSFET gate charge is also limited by power dissipation in
the MIC2186. The power dissipated by the gate drive circuitry
is calculated below:
PGATE_DRIVE =QGATE · VINP · fS
where: QGATE is the total gate charge of both of the external
n- and p-channel MOSFETs.
The graph in Figure 7 shows the total gate charge which can
be driven by the MIC2185 over the input voltage range, for
different values of switching frequency.
)
where:
RWINDING is the winding resistance of the inductor
RDS(ON) is the on resistance of the low side switching
MOSFET
The maximum value of current sense resistor is:
V
RSENSE = SENSE
IIND(pk)
where:
VSENSE is the minimum current sense threshold of
the CSH pin
The current sense pin, CSH, is noise sensitive due to the
low signal level. The current sense voltage measurement
is referenced to the signal ground pin of the MIC2185. The
current sense resistor ground should be located close to the
IC ground. Make sure there are no high currents flowing
in this trace. The PCB trace between the high side of the
current sense resistor and the CHS pin should also be short
and routed close to the ground connection. The input to the
internal current sense amplifier has a 30nS dead time at the
beginning of each switching cycle. This dead time prevents
leading edge current spikes from prematurely terminating the
switching cycle. A small RC filter between the current sense
pin and current sense resistor may help to attenuate larger
switching spikes or high frequency switching noise. Adding
the filter slows down the current sense signal, which has the
effect of slightly raising the overcurrent limit threshold.
MOSFET Gate Drive
The MIC2185 synchronous boost converter drives both a
high side and low side MOSFET. The low side drive, OUTN,
drives an n-channel MOSFET. The high-side drive, OUTP,
is designed to switch a p-channel MOSFET (the p-channel
MOSFET doesn't require a bootstrap circuit which would
be needed to drive an n-channel MOSFET). The VINP pin
must be connected to the output, which provides power to
drive the high and low side MOSFETs. In skip mode, the
high side MOSFET is disabled by forcing the OUTP pin to
be high (equal to VOUT).
MOSFET Selection
In a boost converter, the VDS of the MOSFET, Q1, is approximately equal to the output voltage. The maximum Vds
rating of the MOSFET must be high enough to allow for ringing and spikes. The MIC2185 input voltage range is 2.9V to
14V. MOSFETs with 20V and 30V VDS ratings are ideal for
use with this part.
The n-channel gate drive voltage is supplied by the OUTN
output. At startup in a boost converter, the output voltage
equals the input voltage. The VGS threshold voltage of the
n-channel MOSFET must be low enough to operate at the
minimum input voltage to guarantee the boost converter will
start up. The p-channel MOSFET must have a minimum
threshold voltage equal to or lower than the output voltage.
Five volt threshold (logic level) MOSFETs are recommended
for the p-channel MOSFET. Ringing in the gate drive signal
October 2005
140
120
Frequency vs.
Maximum Gate Charge
400kHz
200kHz
300kHz
100
80
60
40
500kHz
600kHz
20
0
3
5
7
9
11
13
INPUT VOLTAGE (V)
Figure 7 - MIC2185 Frequency vs. Max. Gate Charge
External Schottky Diode
An external boost diode in parallel with the high side MOSFET
is used to keep the inductor current flow continuous during
the non-overlap time when both MOSFETs are turned off.
Although the average current through this diode is small,
the diode must be able to handle currents equal to the peak
inductor current. This peak current is calculated in the Current Limit section of this specification
The reverse voltage requirement of the diode is:
VDIODE_RRM= VOUT
For the MIC2185, Schottky diodes with a 30V or 40V rating
are recommended. Schottky diodes with lower reverse voltage ratings have higher reverse leakage current which will
cause ringing and excessive power dissipation in the diode
and low side MOSFET.
The external Schottky diode is not necessary for circuit
operation since the high side MOSFET contains a parasitic
body diode. However, the body diode has a relatively slow
reverse recovery time and a relatively high forward voltage
drop. The lower forward voltage drop of the Schottky diode
both prevents the parasitic diode from turning on and improves efficiency. The lack of a reverse recovery mechanism
in a Schottky diode causes less ringing than the MOSFET's
parasitic diode. Depending on the circuit components and
operating conditions, an external Schottky diode will improve
the converter efficiency by 1/2% to 1%.
11
MIC2185
MIC2185
Micrel, Inc.
Reference, Enable and UVLO Circuits
The output drivers are enabled when the following conditions
are satisfied:
• The VDD voltage (pin 10) is greater than its
undervoltage threshold.
• The voltage on the Enable pin is greater than
the Enable /UVLO threshold.
The internal bias circuitry generates a 1.245V bandgap
reference for the voltage error amplifier and a 3V VDD voltage for the internal supply bus. The reference voltage in the
MIC2185 is buffered and brought out to pin 8. The VREF
pin must be bypassed to GND (pin 4) with a 0.1µF capacitor. The VDD pin must be decoupled to ground with a 1µF
ceramic capacitor.
The Enable pin (pin 7) has two threshold levels, allowing the
MIC2185 to shut down in a micro-current mode, or turn off
output switching in standby mode. Below 0.9V (typical), the
device is forced into a low-power shutdown. If the enable pin
is between 0.9V and 1.5V (typical) the output gate drive is
disabled but the internal circuitry is powered on and the soft
start pin voltage is forced low. There is typically 140mV of
hysteresis below the 1.5V threshold to insure the part does
not oscillate on and off due to ripple voltage on the input.
Raising the Enable voltage above the UVLO threshold of 1.5V
enables the output drivers and allows the soft start capacitor
to charge. The Enable pin may be pulled up to VINA.
Oscillator & Sync
The internal oscillator is self-contained and requires no
external components. The f/2 pin allows the user to select
from two switching frequencies. A low level sets the oscillator frequency to 400kHz and a high level sets the oscillator
frequency to 200kHz. The maximum duty cycle for both
frequencies is typically 85%. The minimum pulse width increases but does not double when the frequency is changed
from 400kHz to 200kHz. This means the minimum duty cycle
is slightly lower at 200kHz. This may be important as the
input voltage approaches the output voltage. At lower duty
cycles, the input voltage can be closer to the output voltage
without the output rising out of regulation.
A frequency foldback mode is enabled if the voltage on the
Feedback pin (pin 6) is less than 0.3V. In frequency foldback
the oscillator frequency is reduced by approximately a factor
of 4. For the 400kHz setting, the oscillator runs at 100khz in
frequency foldback. For a 200kHz setting the oscillator runs
at approximately 50kHz.
The SYNC input (pin 11) allows the MIC2185 to synchronize
with an external CMOS or TTL clock signal. The rising edge
of the sync signal generates a reset signal in the oscillator,
which turns off the high side gate drive output. The low sidedrive then turns on, restarting the switching cycle. The sync
signal is inhibited when the controller operates in skip mode
or frequency foldback. The sync signal frequency must be
greater than the maximum specified free running frequency of
the MIC2185. If the synchronizing frequency is lower, double
pulsing of the gate drive outputs will occur. When not used,
the sync pin must be connected to ground.
Figure 8 shows the timing between the external sync signal,
MIC2185
low side-drive and the high side drive when the f/2 pin is low.
The delay between the rising edge of the sync signal and the
turn on of the low side gate drive is typically 900ns when the
f/2 pin is high and 600ns when the f/2 pin is low.
Sync Waveform
Sync Input
2V/div
Switch NodeVoltage
(Low Side FET Drain)
5V/div
High Side FET
Gate Drive
5V/div
Low Side FET
Gate Drive
5V/div
600ns
TIME (500ns/div)
Figure 8. Sync Waveforms
The maximum recommended output switching frequency is
600kHz. Synchronizing to higher frequencies may be possible, however there are some concerns. As the switching
frequency is increased, the switching period decreases.
The minimum on time in the MIC2185 becomes a greater
part of the total switching period. This may prevent proper
operation as Vin approaches Vout and may also minimize
the effectiveness of the current limit circuitry. The maximum
duty cycle decreases as the sync frequency is increased.
Figure 9 shows the relationship between the minimum and
maximum duty cycle and frequency.
MIC2185 Sync Frequency
vs. Duty cycle
100
90
F /2 LOW
F /2 HIG H
80
70
60
50
40
18
16
14
12
10
8
6 F /2 HIG H
F /2 LOW
4
2
0
0 100 200 300 400 500 600
FREQUENCY (kHz)
Figure 9
Table 1 summarizes the differences in the MIC2185 for the
two different states of the f/2 pin.
F/2 pin Switching Typical
Typical
tOFF in
Level Frequency Max Duty Min. Duty SKIP Mode
(kHz)
cycle (%) cycle (%)
0
400
85
6
1µs
1
200
85
6
2µs
MIC2185 Table 1
12
October 2005
MIC2185
Micrel, Inc.
Soft Start
Soft Start reduces the power supply input surge current at
start up by limiting the output voltage rise time. Input surge
current occurs when the boost converter charges up the output
capacitance. Slowing the output rise time lowers the input
surge current. Soft Start may also be used for power supply
sequencing. The soft start cannot control the initial surge of
current in a boost converter when VIN is applied. This surge
current is caused by the output capacitance charging up to
the input voltage. The current flows from the input through
the inductor and output diode to the output capacitors.
The soft start voltage is applied directly to the PWM comparator. A 5µA internal current source is used to charge up the
soft start capacitor. Either of 2 UVLO conditions will pull the
soft start capacitor low.
• When the VDD voltage drops below its UVLO
threshold
• When the Enable pin drops below the UVLO
threshold
Voltage Setting Components
The MIC2185 requires two resistors to set the output voltage
as shown in Figure 11.
MIC2185
Voltage
Amplifier
Pin
6
VREF
1.245V
R2
Figure 11
The output voltage is determined by the equation below.
 R1
VO = VREF × 1 +

 R2 
The part switches at a low duty cycle when the soft start pin
voltage zero. As the soft start voltage rises from 0V to 0.7V,
the duty cycle increases from the minimum duty cycle to
the operating duty cycle. The oscillator runs at the foldback
frequency until the feedback voltage rises above 0.3V. In
a boost converter the output voltage is equal to the input
voltage before the MIC2185 starts switching. If the ratio of
Vout/Vin is low, the voltage on the feedback pin will already
be greater than 0.3V and the converter begin switching at
the selected operating frequency.
The risetime of the output is dependent on the soft start
capacitor, output capacitance, input and output voltage and
load current. The scope photo in Figure10 shows the output
voltage and the soft start pin voltage at startup. The output
voltage is initially at the input voltage less a diode drop. After
the converter is enabled the output slowly rises due to the
minimum duty cycle of the controller. As the soft start voltage
increases, the output voltage rises in a controlled fashion until
the output voltage reaches the regulated value.
where:
VREF for the MIC2185 is nominally 1.245V.
Lower values of resistance are preferred to prevent noise
from apprearing on the VFB pin. A typically recommended
value for R1 is 10kΩ.
Decoupling Capacitor Selection
A 1µF decoupling capacitor is used to stabilize the internal
regulator and minimize noise on the VDD pin. Placement
of this capacitor is critical to the proper operation of the
MIC2185. It must be next to the VDD and signal ground
pins. The capacitor should be a good quality ceramic. Incorrect placement of the VDD decoupling capacitor will cause
jitter and/or oscillations in the switching waveform as well as
variations in the overcurrent limit.
A minimum 0.1µF ceramic capacitor is required to decouple
the VIN pin. The capacitor should be placed near the IC and
connected directly between pin 10 (VDD) and pin 5 (SGND).
A 0.1µF capacitor is required to decouple VREF. It should
be located near the VREF pin.
Efficiency calculation and considerations
Efficiency is the ratio of output power to input power. The
difference is dissipated as heat in the boost converter. The
significant contributors at light output loads are:
• The VINA pin supply current.
• The VINP pin supply current which includes the
current required to switch the external MOSFETs
• Core losses in the inductor
To maximize efficiency at light loads:
• Use a low gate charge MOSFET or use the
smallest MOSFET, which is still adequate for the
maximum output current.
• Allow the MIC2185 to run in skip mode at lower
currents. If running in PWM mode, set the frequency to 200kHz.
Soft StartWaveform
VOUT
2V/div
VSS
1V/div
0V
TIME (2ms/div)
Figure 10 Soft Start
October 2005
R1
13
MIC2185
MIC2185
Micrel, Inc.
• Use a ferrite material for the inductor core, which
has less core loss than an MPP or iron power
core.
The significant contributors to power loss at higher output
loads are (in approximate order of magnitude):
• Resistive on-time losses in both MOSFETs
• Switching transition losses in the low side MOSFET
• Inductor resistive losses
• Current sense resistor losses
• Output capacitor resistive losses (due to the
capacitor’s ESR)
To minimize power loss under heavy loads:
• Use logic level, low on-resistance MOSFETs.
Multiplying the gate charge by the on-resistance
gives a figure of merit, providing a good balance
between switching and resistive power dissipation.
• Slow transition times and oscillations on the
voltage and current waveforms dissipate more
power during the turn-on and turn-off of the
low side MOSFET. A clean layout will minimize
parasitic inductance and capacitance in the gate
drive and high current paths. This will allow the
fastest transition times and waveforms without
oscillations. Low gate charge MOSFETs will
switch faster than those with higher gate charge
specifications.
• For the same size inductor, a lower value will
have fewer turns and therefore, lower winding
resistance. However, using too small of a value
will increase the inductor current and therefore
require more output capacitors to filter the output
ripple.
• Lowering the current sense resistor value will
decrease the power dissipated in the resistor.
However, it will also increase the overcurrent
limit and may require larger MOSFETs and
inductor components to handle the higher currents.
• Use low ESR output capacitors to minimize the
power dissipated in the capacitor’s ESR.
MIC2185
14
October 2005
MIC2185
Micrel, Inc.
Package Information
PIN 1
0.157 (3.99)
0.150 (3.81)
0.020 (0.51)
REF
DIMENSIONS:
INCHES (MM)
0.020 (0.51)
0.013 (0.33) 0.0098 (0.249)
0.0040 (0.102)
0.050 (1.27)
BSC
0.394 (10.00)
0.386 (9.80)
0.0648 (1.646)
0.0434 (1.102)
45°
0°–8°
0.050 (1.27)
0.016 (0.40)
SEATING
PLANE
0.244 (6.20)
0.228 (5.79)
16-Pin SOIC (M)
PIN 1
DIMENSIONS:
INCHES (MM)
0.157 (3.99)
0.150 (3.81)
0.009 (0.2286)
REF
0.025 (0.635)
BSC
0.0098 (0.249)
0.0040 (0.102)
SEATING 0.0688 (1.748)
PLANE 0.0532 (1.351)
0.012 (0.30)
0.008 (0.20)
0.0098 (0.249)
0.0075 (0.190)
0.196 (4.98)
0.189 (4.80)
45°
8°
0°
0.050 (1.27)
0.016 (0.40)
0.2284 (5.801)
0.2240 (5.690)
16-Pin QSOP (QS)
MICREL INC.
2180 FORTUNE DRIVE
SAN JOSE, CA 95131
USA
TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com
This information furnished by�
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not�
reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's
use or sale of Micrel Pr�
Micrel for any damages resulting from such use or sale.
© 2002 Micrel, Inc.
October 2005
15
MIC2185