■ ■ ■ ■ The SY10/100E112 are quad drivers designed for use in new, high-performance ECL systems. The E112 has two pairs of OR/NOR outputs from each gate and a common, buffered enable input. The data input can also be used as an ECL memory address fan-out driver, although the E111 is designed specifically for this purpose, and offers lower skew than the E112. For memory address driver applications where scan capabilities are required, please refer to the SY10/100E212 device. 600ps max. propagation delay Extended 100E VEE range of –4.2V to –5.5V Common enable input Fully compatible with industry standard 10KH, 100K I/O levels ■ Internal 75KΩ input pulldown resistors ■ Fully compatible with Motorola MC10E/100E112 ■ Available in 28-pin PLCC package BLOCK DIAGRAM PIN NAMES Pin Q0a Q0b Q0a Q0b Q1a D1 SY100E112 DESCRIPTION FEATURES D0 SY10E112 SY100E112 SY10E112 QUAD DRIVER Micrel, Inc. Function D0-D3 Data Inputs EN Enable Input Qna, Qnb True Outputs Qna, Qnb Inverting Outputs VCCO VCC to Output Q1b Q1a Q1b D2 Q2a Q2b Q2a Q2b D3 Q3a Q3b Q3a Q3b EN M9999-032006 [email protected] or (408) 955-1690 Rev.: G 1 Amendment: /0 Issue Date: March 2006 SY10E112 SY100E112 Micrel, Inc. PACKAGE/ORDERING INFORMATION VCCO Q2b Q2a Q3a Q3b Q3a Q3b Ordering Information(1) 25 24 23 22 21 20 19 VCCO 26 18 Q2b D3 D2 VEE D1 27 17 Q2a VCC Q1b D0 EN 3 28 16 PLCC TOP VIEW J28-1 1 2 15 14 13 12 4 10 11 VCCO 9 Q0a Q0b 8 Q0b 7 Q0a 6 NC VCCO 5 28-Pin PLCC (J28-1) Q1a Q1b Q1a Part Number Package Type Operating Range Package Marking Lead Finish SY10E112JI J28-1 Industrial SY10E112JI Sn-Pb SY10E112JITR(2) J28-1 Industrial SY10E112JI Sn-Pb SY100E112JI J28-1 Industrial SY100E112JI Sn-Pb SY100E112JITR(2) J28-1 Industrial SY100E112JI Sn-Pb SY10E112JC J28-1 Commercial SY10E112JC Sn-Pb SY10E112JCTR(2) J28-1 Commercial SY10E112JC Sn-Pb SY100E112JC J28-1 Commercial SY100E112JC Sn-Pb SY100E112JCTR(2) J28-1 Commercial SY100E112JC Sn-Pb SY10E112JY(3) J28-1 Industrial SY10E112JY with Matte-Sn Pb-Free bar-line indicator SY10E112JYTR(2, 3) J28-1 Industrial SY10E112JY with Matte-Sn Pb-Free bar-line indicator SY100E112JY(3) J28-1 Industrial SY100E112JY with Matte-Sn Pb-Free bar-line indicator SY100E112JYTR(2, 3) J28-1 Industrial SY100E112JY with Matte-Sn Pb-Free bar-line indic ator Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032006 [email protected] or (408) 955-1690 2 SY10E112 SY100E112 Micrel, Inc. TRUTH TABLE EN Qn Qn L Dn Dn H H L DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = –40°C Symbol IIH IEE Parameter TA = 0°C Min. Typ. Max. Min. Typ. TA = +25°C TA = +85°C Max. Min. Typ. Max. Min. Typ. Max. Unit µA Input HIGH Current EN D — — — — 150 200 — — — — 150 200 — — — — 150 200 — — — — 150 200 — — 47 47 56 56 — — 47 47 56 56 — — 47 47 56 56 — — 47 54 56 65 Power Supply Current mA 10E 100E AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = –40°C Symbol tPD tskew tr tf Parameter TA = +25°C TA = +85°C Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Propagation Delay to Output D 200 EN 275 400 450 600 675 200 275 400 450 600 675 200 275 400 450 600 675 200 275 400 450 600 675 Within-Device Skew Dn to Qn, Qn(1) Qna to Qnb(2) — — 80 40 — — — — 80 40 — — — — 80 40 — — — — 80 40 — — 275 425 700 275 425 700 275 425 700 275 425 700 Rise/Fall Time 20% to 80% Min. TA = 0°C ps ps Notes: 1. Within-device skew is defined as identical transitions on similar paths through a device. 2. Skew defined between common OR or common NOR outputs of a single gate. M9999-032006 [email protected] or (408) 955-1690 Unit 3 ps SY10E112 SY100E112 Micrel, Inc. 28-PIN PLCC (J28-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-032006 [email protected] or (408) 955-1690 4