MBR10H100CT SWITCHMODE™ Power Rectifier 100 V, 10 A Features and Benefits • • • • • • • http://onsemi.com Low Forward Voltage: 0.61 V @ 125°C Low Power Loss/High Efficiency High Surge Capacity 175°C Operating Junction Temperature 10 A Total (5.0 A Per Diode Leg) Guard−Ring for Stress Protection Pb−Free Package is Available SCHOTTKY BARRIER RECTIFIER 10 AMPERES 100 VOLTS 1 2, 4 Applications 3 • Power Supply − Output Rectification • Power Management • Instrumentation MARKING DIAGRAM 4 Mechanical Characteristics: • • • • • • Case: Epoxy, Molded Epoxy Meets UL 94 V−0 @ 0.125 in Weight: 1.9 Grams (Approximately) Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds Shipped 50 Units Per Plastic Tube MAXIMUM RATINGS TO−220AB CASE 221A PLASTIC 1 2 YYWW B10H100 AKA 3 YY WW B10H100 AKA = Year = Work Week = Device Code = Polarity Designator ORDERING INFORMATION Please See the Table on the Following Page Device MBR10H100CT MBR10H100CTG © Semiconductor Components Industries, LLC, 2005 June, 2005 − Rev. 0 1 Package Shipping TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail Publication Order Number: MBR10H100CT/D MBR10H100CT MAXIMUM RATINGS (Per Diode Leg) Rating Symbol Value Unit Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage VRRM VRWM VR 100 V Average Rectified Forward Current (Rated VR) TC = 168°C IF(AV) 5.0 A Peak Repetitive Forward Current (Rated VR, Square Wave, 20 kHz) TC = 165°C IFRM 10 A Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) IFSM 180 A TJ +175 °C Storage Temperature Tstg *65 to +175 °C Voltage Rate of Change (Rated VR) dv/dt 10,000 V/ms WAVAL 100 mJ > 400 > 8000 V 2.0 60 °C/W Operating Junction Temperature (Note 1) Controlled Avalanche Energy (see test conditions in Figures 10 and 11) ESD Ratings: Machine Model = C Human Body Model = 3B THERMAL CHARACTERISTICS Maximum Thermal Resistance − Junction−to−Case − Junction−to−Ambient RqJC RqJA ELECTRICAL CHARACTERISTICS (Per Diode Leg) Maximum Instantaneous Forward Voltage (Note 2) (IF = 5.0 A, TC = 25°C) (IF = 5.0 A, TC = 125°C) (IF = 10 A, TC = 25°C) (IF = 10 A, TC = 125°C) vF Maximum Instantaneous Reverse Current (Note 2) (Rated DC Voltage, TC = 125°C) (Rated DC Voltage, TC = 25°C) iR V 0.73 0.61 0.85 0.71 mA 4.5 0.0035 Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. The heat generated must be less than the thermal conductivity from Junction−to−Ambient: dPD/dTJ < 1/RqJA. 2. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%. http://onsemi.com 2 IF, INSTANTANEOUS FORWARD CURRENT (AMPS) IF, INSTANTANEOUS FORWARD CURRENT (AMPS) MBR10H100CT 100 TJ = 150°C 10 TJ = 125°C TJ = 25°C 1 0.1 0 0.2 0.4 0.6 1.0 0.8 1.2 1.4 VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 100 TJ = 150°C 10 TJ = 125°C TJ = 25°C 1 0.1 0 0.2 1.0 0.8 1.2 1.4 1.0E−01 IR, REVERSE CURRENT (AMPS) 1.0E−01 1.0E−02 TJ = 150°C 1.0E−02 TJ = 150°C 1.0E−03 1.0E−03 TJ = 125°C 1.0E−04 TJ = 125°C 1.0E−04 1.0E−05 1.0E−05 1.0E−06 TJ = 25°C 1.0E−06 TJ = 25°C 1.0E−07 1.0E−07 1.0E−08 0 20 60 40 80 100 20 40 60 80 VR, REVERSE VOLTAGE (VOLTS) VR, REVERSE VOLTAGE (VOLTS) Figure 3. Typical Reverse Current Figure 4. Maximum Reverse Current 10 dc SQUARE WAVE 5 110 1.0E−08 0 PFO, AVERAGE POWER DISSIPATION (WATTS) IF, AVERAGE FORWARD CURRENT (AMPS) 0.6 Figure 2. Maximum Forward Voltage IR, MAXIMUM REVERSE CURRENT (AMPS) Figure 1. Typical Forward Voltage 0 100 0.4 VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 120 130 140 150 160 170 180 16 14 12 10 8 SQUARE 6 DC 4 2 0 0 5 10 TC, CASE TEMPERATURE (°C) IO, AVERAGE FORWARD CURRENT (AMPS) Figure 5. Current Derating Figure 6. Forward Power Dissipation http://onsemi.com 3 100 15 MBR10H100CT 1000 C, CAPACITANCE (pF) TJ = 25°C 100 10 0 20 40 80 60 100 VR, REVERSE VOLTAGE (VOLTS) R(t), TRANSIENT THERMAL RESISTANCE Figure 7. Capacitance 100 D = 0.5 10 0.2 0.1 1 0.05 P(pk) 0.01 t1 0.1 0.01 0.000001 0.00001 t2 DUTY CYCLE, D = t1/t2 SINGLE PULSE 0.0001 0.001 0.1 0.01 1 10 100 1000 t1, TIME (sec) R(t), TRANSIENT THERMAL RESISTANCE Figure 8. Thermal Response Junction−to−Ambient 10 1 D = 0.5 0.2 0.1 0.05 0.1 P(pk) 0.01 t1 0.01 0.000001 0.00001 t2 DUTY CYCLE, D = t1/t2 SINGLE PULSE 0.0001 0.001 0.1 0.01 1 t1, TIME (sec) Figure 9. Thermal Response Junction−to−Case http://onsemi.com 4 10 100 1000 MBR10H100CT +VDD IL 10 mH COIL BVDUT VD MERCURY SWITCH S1 ID ID IL DUT VDD t0 Figure 10. Test Circuit t1 t2 t Figure 11. Current−Voltage Waveforms elements are small Equation (1) approximates the total energy transferred to the diode. It can be seen from this equation that if the VDD voltage is low compared to the breakdown voltage of the device, the amount of energy contributed by the supply during breakdown is small and the total energy can be assumed to be nearly equal to the energy stored in the coil during the time when S1 was closed, Equation (2). The unclamped inductive switching circuit shown in Figure 10 was used to demonstrate the controlled avalanche capability of this device. A mercury switch was used instead of an electronic switch to simulate a noisy environment when the switch was being opened. When S1 is closed at t0 the current in the inductor IL ramps up linearly; and energy is stored in the coil. At t1 the switch is opened and the voltage across the diode under test begins to rise rapidly, due to di/dt effects, when this induced voltage reaches the breakdown voltage of the diode, it is clamped at BVDUT and the diode begins to conduct the full load current which now starts to decay linearly through the diode, and goes to zero at t2. By solving the loop equation at the point in time when S1 is opened; and calculating the energy that is transferred to the diode it can be shown that the total energy transferred is equal to the energy stored in the inductor plus a finite amount of energy from the VDD power supply while the diode is in breakdown (from t1 to t2) minus any losses due to finite component resistances. Assuming the component resistive EQUATION (1): ǒ BV 2 DUT W [ 1 LI LPK AVAL 2 BV –V DUT DD EQUATION (2): 2 W [ 1 LI LPK AVAL 2 http://onsemi.com 5 Ǔ MBR10H100CT PACKAGE DIMENSIONS TO−220 PLASTIC CASE 221A−09 ISSUE AA −T− B SEATING PLANE C F T S 4 DIM A B C D F G H J K L N Q R S T U V Z A Q 1 2 3 U H K Z L R V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. J G D N INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 −−− −−− 0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 −−− −−− 2.04 SWITCHMODE is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 6 For additional information, please contact your local Sales Representative. MBR10H100CT/D