ONSEMI MC10161

MC10161
Binary to 1-8 Decoder
(Low)
The MC10161 is designed to decode a three bit input word to a one
of eight line output. The selected output will be low while all other
outputs will be high. The enable inputs, when either or both are high,
force all outputs high.
The MC10161 is a true parallel decoder. No series gating is used
internally, eliminating unequal delay times found in other decoders.
This design provides the identical 4 ns delay from any address or enable
input to any output.
A complete mux/demux operation on 16 bits for data distribution is
illustrated in Figure 1. This system, using the MC10136 control
counters, has the capability of incrementing, decrementing or holding
data channels. When both S0 and S1 are low, the index counters reset,
thus initializing both the mux and demux units. The four binary
outputs of the counter are buffered by the MC10161s to send
twisted–pair select data to the multiplexer/demultiplexer to units.
• PD = 315 mW typ/pkg (No Load)
• tpd = 4.0 ns typ
• tr, tf = 2.0 ns typ (20%–80%)
http://onsemi.com
MARKING
DIAGRAMS
16
CDIP–16
L SUFFIX
CASE 620
1
16
PDIP–16
P SUFFIX
CASE 648
1
PLCC–20
FN SUFFIX
CASE 775
E02
6Q0
A
WL
YY
WW
5Q1
4Q2
A7
MC10161P
AWLYYWW
1
LOGIC DIAGRAM
E115
MC10161L
AWLYYWW
10161
AWLYYWW
= Assembly Location
= Wafer Lot
= Year
= Work Week
3Q3
DIP PIN ASSIGNMENT
13Q4
B9
12Q5
VCC1
1
16
VCC2
E0
2
15
E1
Q3
3
14
C
Q2
4
13
Q4
Q1
5
12
Q5
Q0
6
11
Q6
A
7
10
Q7
VEE
8
9
B
11Q6
C14
10Q7
VCC1 = PIN 1
VCC2 = PIN 16
VEE = PIN 8
TRUTH TABLE
ENABLE
INPUTS
INPUTS
OUTPUTS
E1
E0
C
B
A
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
L
L
L
L
L
L
L
L
H
X
L
L
L
L
L
L
L
L
X
H
L
L
L
L
H
H
H
H
X
X
L
L
H
H
L
L
H
H
X
X
L
H
L
H
L
H
L
H
X
X
L
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
H
L
H
H
 Semiconductor Components Industries, LLC, 2002
January, 2002 – Rev. 7
1
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion Tables
on page 18 of the ON Semiconductor MECL Data Book
(DL122/D).
ORDERING INFORMATION
Device
Package
Shipping
MC10161L
CDIP–16
25 Units / Rail
MC10161P
PDIP–16
25 Units / Rail
MC10161FN
PLCC–20
46 Units / Rail
Publication Order Number:
MC10161/D
MC10161
ELECTRICAL CHARACTERISTICS
Test Limits
Characteristic
Symbol
Pin
Under
Test
Power Supply Drain Current
IE
8
84
IinH
14
350
Input Current
–30°C
Min
+25°C
Max
Min
+85°C
Typ
Max
Max
Unit
61
76
Min
84
mAdc
220
220
µAdc
14
0.5
13
13
–1.060
–1.060
–0.890
–0.890
–0.960
–0.960
–0.810
–0.810
–0.890
–0.890
–0.700
–0.700
Vdc
Logic 0
VOL
13
–1.890
–1.675
–1.850
–1.650
–1.825
–1.615
Vdc
Logic 1
VOHA
13
13
–1.080
–1.080
Logic 0
VOLA
13
Logic 1
Output Voltage
Threshold Voltage
Threshold Voltage
0.5
µAdc
IinL
VOH
Output Voltage
0.3
–0.980
–0.980
–0.910
–0.910
–1.655
Vdc
–1.630
–1.595
Switching Times (50Ω Load)
Propagation Delay
Vdc
ns
t14+13–
t14–13+
13
13
1.5
1.5
6.2
6.2
1.5
1.5
4.0
4.0
6.0
6.0
1.5
1.5
6.4
6.4
Rise Time
(20 to 80%)
t13+
13
1.0
3.3
1.1
2.0
3.3
1.1
3.5
Fall Time
(20 to 80%)
t13–
13
1.0
3.3
1.1
2.0
3.3
1.1
3.5
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts)
Characteristic
Power Supply Drain Current
Input Current
@ Test Temperature
VIHmax
VILmin
VIHAmin
VILAmax
VEE
–30°C
–0.890
–1.890
–1.205
–1.500
–5.2
+25°C
–0.810
–1.850
–1.105
–1.475
–5.2
+85°C
–0.700
–1.825
–1.035
–1.440
–5.2
Symbol
Pin
Under
Test
VIHmax
IE
8
IinH
14
IinL
14
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
VEE
(VCC)
Gnd
2,7,9,14,15
8
1,16
14
8
1,16
8
1,16
VILmin
VIHAmin
VILAmax
14
Output Voltage
Logic 1
VOH
13
13
2
15
8
8
1,16
1,16
Output Voltage
Logic 0
VOL
13
14
8
1,16
Threshold Voltage
Logic 1
VOHA
13
13
2
15
8
8
1,16
1,16
Threshold Voltage
Logic 0
VOLA
13
14
8
1,16
Pulse In
Pulse Out
–3.2 V
+2.0 V
t14+13–
t14–13+
13
13
14
14
13
13
8
8
1,16
1,16
Switching Times
(50Ω Load)
Propagation Delay
Rise Time
(20 to 80%)
t13+
13
14
13
8
1,16
Fall Time
(20 to 80%)
t13–
13
14
13
8
1,16
Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.
Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the
same manner.
http://onsemi.com
2
MC10161
FIGURE 1 — HIGH SPEED 16-BIT MULTIPLEXER/DEMULTIPLEXER
Control Selection
MC10161
MC10115
S0
S1
CR
A
MC10161
15 14 13 12 11 10 9 8
7 6 5 4 3 2 1 0
MC10136
B
C
D
E1
C
B
A
MC10164
E1
C
B
A
MC10161
D0
E1
C
B
A
MC10164
E1
C
B
A
MC10161
D0
MC10115
S0
S0
S1
S1
CR
A
CR
MC10136
B
C
D
Start/Stop
E0
15 14 13 12 11 10 9 8
http://onsemi.com
3
E0
7 6 5 4 3 2 1 0
MC10161
PACKAGE DIMENSIONS
PLCC–20
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
0.007 (0.180)
B
Y BRK
–N–
M
T L-M
0.007 (0.180)
U
M
N
S
T L-M
S
G1
0.010 (0.250)
S
N
S
D
–L–
–M–
Z
W
20
D
1
X
V
S
T L-M
S
N
S
VIEW D–D
A
0.007 (0.180)
M
T L-M
S
N
S
R
0.007 (0.180)
M
T L-M
S
N
S
Z
0.007 (0.180)
H
M
T L-M
S
N
S
K1
K
C
E
F
0.004 (0.100)
G
J
–T–
VIEW S
G1
0.010 (0.250) S T L-M
S
N
S
0.007 (0.180)
M
T L-M
S
VIEW S
SEATING
PLANE
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
http://onsemi.com
4
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.385
0.395
0.385
0.395
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
--0.025
--0.350
0.356
0.350
0.356
0.042
0.048
0.042
0.048
0.042
0.056
--0.020
2
10 0.310
0.330
0.040
---
MILLIMETERS
MIN
MAX
9.78
10.03
9.78
10.03
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
--0.64
--8.89
9.04
8.89
9.04
1.07
1.21
1.07
1.21
1.07
1.42
--0.50
2
10 7.88
8.38
1.02
---
N
S
MC10161
PACKAGE DIMENSIONS
–A–
16
9
1
8
–B–
CDIP–16
L SUFFIX
CERAMIC DIP PACKAGE
CASE 620–10
ISSUE T
C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
L
DIM
A
B
C
D
E
F
G
H
K
L
M
N
–T–
K
N
SEATING
PLANE
M
E
F
J
G
D
16 PL
0.25 (0.010)
16 PL
0.25 (0.010)
M
T A
T B
M
S
PDIP–16
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
–A–
16
9
1
8
B
F
C
L
S
–T–
SEATING
PLANE
K
H
G
D
M
J
16 PL
0.25 (0.010)
M
S
T A
M
http://onsemi.com
5
INCHES
MIN
MAX
0.750
0.785
0.240
0.295
--0.200
0.015
0.020
0.050 BSC
0.055
0.065
0.100 BSC
0.008
0.015
0.125
0.170
0.300 BSC
0
15 0.020
0.040
MILLIMETERS
MIN
MAX
19.05
19.93
6.10
7.49
--5.08
0.39
0.50
1.27 BSC
1.40
1.65
2.54 BSC
0.21
0.38
3.18
4.31
7.62 BSC
0
15 0.51
1.01
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0
10 0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0
10 0.51
1.01
MC10161
Notes
http://onsemi.com
6
MC10161
Notes
http://onsemi.com
7
MC10161
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
8
MC10161/D