ONSEMI MC78L12ABDR2G

MC78L00A Series,
NCV78L00A
100 mA Positive Voltage
Regulators
The MC78L00A Series of positive voltage regulators are
inexpensive, easy−to−use devices suitable for a multitude of
applications that require a regulated supply of up to 100 mA. Like
their higher powered MC7800 and MC78M00 Series cousins, these
regulators feature internal current limiting and thermal shutdown
making them remarkably rugged. No external components are
required with the MC78L00 devices in many applications.
These devices offer a substantial performance advantage over the
traditional zener diode−resistor combination, as output impedance
and quiescent current are substantially reduced.
http://onsemi.com
1
Features
•
•
•
•
•
•
•
•
Wide Range of Available, Fixed Output Voltages
Low Cost
Internal Short Circuit Current Limiting
Internal Thermal Overload Protection
No External Components Required
Complementary Negative Regulators Offered (MC79L00A Series)
Pb−Free Packages are Available
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
Q3
15k
Input
Q11
Q5
Q12
Q1
Q10
5.0k
3.8k
Q4
1.9k
1.2k
Q6
Output
0−25k
19k
2.2k
Q9
C
Q8
Q2
Z1
3.0
TO−92
P SUFFIX
CASE 029
2
3
Pin: 1. Output
2. Ground
3. Input
8
1
SOIC−8*
D SUFFIX
CASE 751
*SOIC−8 is an internally modified SO−8 package. Pins
2, 3, 6, and 7 are electrically common to the die attach
flag. This internal lead frame modification decreases
package thermal resistance and increases power
dissipation capability when appropriately mounted on
a printed circuit board. SOIC−8 conforms to all external dimensions of the standard SO−8 package.
PIN CONNECTIONS
VOUT 1
8
VIN
GND 2
7
GND
GND 3
6
GND
NC 4
5
NC
2.85k
(Top View)
Q7
420
1.0k
Ground
Figure 1. Representative Schematic Diagram
Input
MC78LXXA
Cin*
0.33mF
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
DEVICE MARKING INFORMATION
Output
See general marking information in the device marking
section on page 14 of this data sheet.
CO**
Figure 2. Standard Application
A common ground is required between the input and the output voltages. The
input voltage must remain typically 2.0 V above the output voltage even during
the low point on the input ripple voltage.
* Cin is required if regulator is located an appreciable distance from power
supply filter.
** CO is not needed for stability; however, it does improve transient response.
© Semiconductor Components Industries, LLC, 2005
May, 2005 − Rev. 10
1
Publication Order Number:
MC78L00A/D
MC78L00A Series, NCV78L00A
MAXIMUM RATINGS (TA = +125°C, unless otherwise noted.)
Rating
Symbol
Value
Unit
VI
30
35
40
Vdc
Storage Temperature Range
Tstg
−65 to +150
°C
Operating Junction Temperature Range
TJ
0 to +150
°C
Input Voltage (2.6 V−8.0 V)
Input Voltage (12 V−18 V)
Input Voltage (24 V)
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values
(not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage
may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS (VI = 10 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB,
NCV78L05A), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L05AC, AB, NCV78L05A
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = +25°C)
Characteristics
VO
4.8
5.0
5.2
Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
7.0 Vdc ≤ VI ≤ 20 Vdc
8.0 Vdc ≤ VI ≤ 20 Vdc
Regline
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
Output Voltage
(7.0 Vdc ≤ VI ≤ 20 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 10 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
mV
−
−
55
45
150
100
−
−
11
5.0
60
30
4.75
4.75
−
−
5.25
5.25
−
−
3.8
−
6.0
5.5
−
−
−
−
1.5
0.1
mV
Vdc
mA
DIIB
Input Bias Current Change
(8.0 Vdc ≤ VI ≤ 20 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
−
40
−
mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 8.0 Vdc ≤ VI ≤ 18 V, TJ = +25°C)
RR
41
49
−
dB
VI − VO
−
1.7
−
Vdc
Dropout Voltage (TJ = +25°C)
NOTE:
NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring
site and change control.
http://onsemi.com
2
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (VI = 14 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB),
0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L08AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = +25°C)
VO
7.7
8.0
8.3
Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
10.5 Vdc ≤ VI ≤ 23 Vdc
11 Vdc ≤ VI ≤ 23 Vdc
Regline
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
Output Voltage
(10.5 Vdc ≤ VI ≤ 23 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 14 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
mV
−
−
20
12
175
125
−
−
15
8.0
80
40
7.6
7.6
−
−
8.4
8.4
−
−
3.0
−
6.0
5.5
−
−
−
−
1.5
0.1
mV
Vdc
mA
DIIB
Input Bias Current Change
(11 Vdc ≤ VI ≤ 23 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
−
60
−
mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 12 V ≤ VI ≤ 23 V, TJ = +25°C)
RR
37
57
−
dB
VI − VO
−
1.7
−
Vdc
Dropout Voltage (TJ = +25°C)
ELECTRICAL CHARACTERISTICS (VI = 15 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB),
0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L09AC, AB
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = +25°C)
Characteristics
VO
8.6
9.0
9.4
Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
11.5 Vdc ≤ VI ≤ 24 Vdc
12 Vdc ≤ VI ≤ 24 Vdc
Regline
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
Output Voltage
(11.5 Vdc ≤ VI ≤ 24 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 15 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
mV
−
−
20
12
175
125
−
−
15
8.0
90
40
8.5
8.5
−
−
9.5
9.5
−
−
3.0
−
6.0
5.5
−
−
−
−
1.5
0.1
mV
Vdc
mA
DIIB
Input Bias Current Change
(11 Vdc ≤ VI ≤ 23 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
−
60
−
mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 13 V ≤ VI ≤ 24 V, TJ = +25°C)
RR
37
57
−
dB
VI − VO
−
1.7
−
Vdc
Dropout Voltage
(TJ = +25°C)
http://onsemi.com
3
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (VI = 19 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB),
0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L12AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = +25°C)
VO
11.5
12
12.5
Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
14.5 Vdc ≤ VI ≤ 27 Vdc
16 Vdc ≤ VI ≤ 27 Vdc
Regline
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
Output Voltage
(14.5 Vdc ≤ VI ≤ 27 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 19 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
mV
−
−
120
100
250
200
−
−
20
10
100
50
11.4
11.4
−
−
12.6
12.6
−
−
4.2
−
6.5
6.0
−
−
−
−
1.5
0.1
mV
Vdc
mA
DIIB
Input Bias Current Change
(16 Vdc ≤ VI ≤ 27 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
−
80
−
mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 15 V ≤ VI ≤ 25 V, TJ = +25°C)
RR
37
42
−
dB
VI − VO
−
1.7
−
Vdc
Dropout Voltage
(TJ = +25°C)
ELECTRICAL CHARACTERISTICS (VI = 23 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB),
S 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L15AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = +25°C)
VO
14.4
15
15.6
Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
17.5 Vdc ≤ VI ≤ 30 Vdc
20 Vdc ≤ VI ≤ 30 Vdc
Regline
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
Output Voltage
(17.5 Vdc ≤ VI ≤ 30 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 23 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
mV
−
−
130
110
300
250
−
−
25
12
150
75
14.25
14.25
−
−
15.75
15.75
−
−
4.4
−
6.5
6.0
−
−
−
−
1.5
0.1
mV
Vdc
mA
DIIB
Input Bias Current Change
(20 Vdc ≤ VI ≤ 30 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
−
90
−
mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 18.5 V ≤ VI ≤ 28.5 V, TJ = +25°C)
RR
34
39
−
dB
VI − VO
−
1.7
−
Vdc
Dropout Voltage
(TJ = +25°C)
http://onsemi.com
4
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (VI = 27 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, 0°C < TJ < +125°C, unless otherwise noted.)
MC78L18AC
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = +25°C)
Characteristics
VO
17.3
18
18.7
Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
21.4 Vdc ≤ VI ≤ 33 Vdc
20.7 Vdc ≤ VI ≤ 33 Vdc
22 Vdc ≤ VI ≤ 33 Vdc
21 Vdc ≤ VI ≤ 33 Vdc
Regline
−
45
325
−
35
275
−
−
30
15
170
85
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
Output Voltage
(21.4 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(20.7 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA)
(VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
mV
Vdc
17.1
−
18.9
17.1
−
18.9
−
−
3.1
−
6.5
6.0
mA
DIIB
Input Bias Current Change
(22 Vdc ≤ VI ≤ 33 Vdc)
(21 Vdc ≤ VI ≤ 33 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
mV
mA
−
−
−
−
1.5
0.1
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
−
150
−
mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 23 V ≤ VI ≤ 33 V, TJ = +25°C)
RR
33
48
−
dB
VI − VO
−
1.7
−
Vdc
Dropout Voltage
(TJ = +25°C)
http://onsemi.com
5
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (VI = 33 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, 0°C < TJ < +125°C, unless otherwise noted.)
MC78L24AC
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = +25°C)
Characteristics
VO
23
24
25
Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
27.5 Vdc ≤ VI ≤ 38 Vdc
28 Vdc ≤ VI ≤ 80 Vdc
27 Vdc ≤ VI ≤ 38 Vdc
Regline
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
Output Voltage
(28 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(27 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(28 Vdc ≤ VI = 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA)
(27 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA)
VO
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
mV
−
−
−
−
50
60
−
300
350
−
−
40
20
200
100
mV
Vdc
22.8
−
25.2
22.8
−
25.2
−
−
3.1
−
6.5
6.0
−
−
−
−
1.5
0.1
mA
DIIB
Input Bias Current Change
(28 Vdc ≤ VI ≤ 38 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
−
200
−
mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 29 V ≤ VI ≤ 35 V, TJ = +25°C)
RR
31
45
−
dB
VI − VO
−
1.7
−
Vdc
Dropout Voltage
(TJ = +25°C)
http://onsemi.com
6
V I −V O , INPUT/OUTPUT DIFFERENTIAL VOLTAGE (V)
MC78L00A Series, NCV78L00A
MC78L05AC
Vout = 5.0 V
TJ = 25°C
6.0
IO = 1.0 mA
4.0
IO = 40 mA
IO = 100 mA
2.0
0
0
2.0
4.0
6.0
VI, INPUT VOLTAGE (V)
8.0
10
Figure 3. Dropout Characteristics
IO = 70 mA
2.0
1.5
IO = 40 mA
1.0
IO = 1.0 mA
Dropout of Regulation is
defined as when
VO = 2% of VO
0.5
0
0
25
4.0
3.8
3.6
3.4
3.2
MC78L05AC
VI = 10 V
VO= 5.0 V
IO = 40 mA
3.0
125
Figure 4. Dropout Voltage versus
Junction Temperature
4.0
MC78L05AC
Vout = 5.0 V
IO = 40 mA
TJ = 25°C
3.0
2.0
1.0
0
0
0
25
50
75
100
TA, AMBIENT TEMPERATURE (°C)
125
0
5.0
10
15
20
25
VI, INPUT VOLTAGE (V)
35
170
10,000
No Heatsink
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
110
100
RqJA = 200°C/W
PD(max) to 25°C = 625 mW
75
100
125
TA, AMBIENT TEMPERATURE (°C)
150
Figure 7. Maximum Average Power Dissipation versus
Ambient Temperature − TO−92 Type Package
Graph represents symmetrical layout
90
L
70
2.0 oz.
Copper
L
2.4
2.0
1.6
1.2
3.0 mm
50
0.8
RqJA
30
0
10
20
30
40
0.4
50
L, LENGTH OF COPPER (mm)
Figure 8. SOIC−8 Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
http://onsemi.com
7
2.8
PD(max) for TA = 50°C
130
1000
50
40
3.2
150
10
25
30
Figure 6. Input Bias Current
versus Input Voltage
R θ JA, THERMAL RESISTANCE JUNCTION-TO-AIR (° C/W)
Figure 5. Input Bias Current versus
Ambient Temperature
PD , POWER DISSIPATION (mW)
50
75
100
TJ, JUNCTION TEMPERATURE (°C)
5.0
I IB , INPUT BIAS CURRENT (mA)
I IB , INPUT BIAS CURRENT (mA)
4.2
2.5
PD, MAXIMUM POWER DISSIPATION (W)
VO, OUTPUT VOLTAGE (V)
8.0
MC78L00A Series, NCV78L00A
APPLICATIONS INFORMATION
Design Considerations
input bypass capacitor should be selected to provide good
high−frequency characteristics to insure stable operation
under all load conditions. A 0.33 mF or larger tantalum,
mylar, or other capacitor having low internal impedance at
high frequencies should be chosen. The bypass capacitor
should be mounted with the shortest possible leads directly
across the regulators input terminals. Good construction
techniques should be used to minimize ground loops and
lead resistance drops since the regulator has no external
sense lead. Bypassing the output is also recommended.
The MC78L00A Series of fixed voltage regulators are
designed with Thermal Overload Protection that shuts
down the circuit when subjected to an excessive power
overload condition. Internal Short Circuit Protection limits
the maximum current the circuit will pass.
In many low current applications, compensation
capacitors are not required. However, it is recommended
that the regulator input be bypassed with a capacitor if the
regulator is connected to the power supply filter with long
wire lengths, or if the output load capacitance is large. The
MC78L15A
+20V
0.33mF
Input
R
IO
6
Constant
Current to
Grounded Load
2
−
MC1741
3
+
4
0.33mF
6.5
20V
The MC78L00 regulators can also be used as a current source
when connected as above. In order to minimize dissipation the
MC78L05C is chosen in this application. Resistor R determines
the current as follows:
5.0 V
IO =
+ IB
R
10k
7
MC78L05A
0.33mF
+VO
10k
MPS A70
−VO
MPS U55
Figure 10. ± 15 V Tracking Voltage Regulator
+VI
MC78LXXA
0.33mF
IIB = 3.8 mA over line and load changes
−VI
For example, a 100 mA current source would require R to be a
50W, 1/2 W resistor and the output voltage compliance would be
the input voltage less 7 V.
0.33mF
+VO
0.1mF
MC79LXXA
0.1mF
−VO
Figure 9. Current Regulator
Figure 11. Positive and Negative Regulator
http://onsemi.com
8
MC78L00A Series, NCV78L00A
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
MC78L05ABD
SOIC−8
98 Units/Rail
MC78L05ABDG
SOIC−8
98 Units/Rail
MC78L05ABDR2
Device
Output Voltage
SOIC−8
2500 Tape & Reel
MC78L05ABDR2G
SOIC−8
(Pb−Free)
2500 Tape & Reel
NCV78L05ABDR2*
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
NCV78L05ABDR2G*
MC78L05ABP
MC78L05ABPG
TJ = −40° to +125°C
MC78L05ABPRA
MC78L05ABPRAG
MC78L05ABPRE
MC78L05ABPREG
MC78L05ABPRM
MC78L05ABPRMG
MC78L05ACD
5.0 V
SOIC−8
98 Units/Rail
MC78L05ACDG
SOIC−8
(Pb−Free)
98 Units/Rail
MC78L05ACDR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
MC78L05ACDR2G
MC78L05ACP
MC78L05ACPG
MC78L05ACPRA
MC78L05ACPRAG
TJ = 0° to +125°C
MC78L05ACPRE
MC78L05ACPREG
MC78L05ACPRM
MC78L05ACPRMG
MC78L05ACPRP
MC78L05ACPRPG
*NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
9
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Operating
Temperature Range
Package
Shipping†
SOIC−8
98 Units/Rail
MC78L08ABDG
SOIC−8
(Pb−Free)
98 Units/Rail
MC78L08ABDR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
SOIC−8
98 Units/Rail
SOIC−8
(Pb−Free)
98 Units/Rail
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
SOIC−8
98 Units/Rail
MC78L09ABDG
SOIC−8
(Pb−Free)
98 Units/Rail
MC78L09ABDR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
Device
Output Voltage
MC78L08ABD
MC78L08ABDR2G
MC78L08ABP
TJ = −40° to +125°C
MC78L08ABPG
MC78L08ABPRA
MC78L08ABPRAG
MC78L08ABPRP
MC78L08ABPRPG
MC78L08ACD
MC78L08ACDG
8.0 V
MC78L08ACDR2
MC78L08ACDR2G
MC78L08ACP
MC78L08ACPG
TJ = 0° to +125°C
MC78L08ACPRA
MC78L08ACPRAG
MC78L08ACPRE
MC78L08ACPREG
MC78L08ACPRP
MC78L08ACPRPG
MC78L09ABD
MC78L09ABDR2G
MC78L09ABPRA
9.0 V
TJ = −40° to +125°C
MC78L09ABPRAG
MC78L09ABPRP
MC78L09ABPRPG
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Operating
Temperature Range
Package
Shipping†
SOIC−8
98 Units/Rail
SOIC−8
(Pb−Free)
98 Units/Rail
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
SOIC−8
98 Units/Rail
MC78L12ABDG
SOIC−8
(Pb−Free)
98 Units/Rail
MC78L12ABDR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Ammo Pack
MC78L12ABPRPG
TO−92
(Pb−Free)
2000 Ammo Pack
NCV78L12ABDR2*
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
SOIC−8
98 Units/Rail
SOIC−8
(Pb−Free)
98 Units/Rail
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
Device
Output Voltage
MC78L09ACD
MC78L09ACDG
MC78L09ACDR2
MC78L09ACDR2G
9.0 V
TJ = 0° to +125°C
MC78L09ACP
MC78L09ACPG
MC78L12ABD
MC78L12ABDR2G
MC78L12ABP
TJ = −40° to +125°C
MC78L12ABPG
MC78L12ABPRP
NCV78L12ABDR2G*
MC78L12ACD
MC78L12ACDG
MC78L12ACDR2
12 V
MC78L12ACDR2G
MC78L12ACP
MC78L12ACPG
MC78L12ACPRA
MC78L12ACPRAG
TJ = 0° to +125°C
MC78L12ACPRE
MC78L12ACPREG
MC78L12ACPRM
MC78L12ACPRMG
MC78L12ACPRP
MC78L12ACPRPG
*NCV78L12A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
11
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Operating
Temperature Range
Package
Shipping†
SOIC−8
98 Units/Rail
MC78L15ABDG
SOIC−8
(Pb−Free)
98 Units/Rail
MC78L15ABDR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
Device
Output Voltage
MC78L15ABD
MC78L15ABDR2G
MC78L15ABP
TJ = −40° to +125°C
MC78L15ABPG
MC78L15ABPRA
MC78L15ABPRAG
MC78L15ABPRP
MC78L15ABPRPG
MC78L15ACD
15 V
SOIC−8
98 Units/Rail
MC78L15ACDG
SOIC−8
(Pb−Free)
98 Units/Rail
MC78L15ACDR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
MC78L15ACDR2G
MC78L15ACP
MC78L15ACPG
TJ = 0° to +125°C
MC78L15ACPRA
MC78L15ACPRAG
MC78L15ACPRP
MC78L15ACPRPG
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
12
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Device
Output Voltage
Operating
Temperature Range
MC78L18ABP
TJ = −40° to +125°C
MC78L18ABPG
MC78L18ACP
MC78L18ACPG
MC78L18ACPRA
MC78L18ACPRAG
18 V
TJ = 0° to +125°C
MC78L18ACPRM
MC78L18ACPRMG
MC78L18ACPRP
MC78L18ACPRPG
MC78L24ABP
TJ = −40° to +125°C
MC78L24ABPG
MC78L24ACP
MC78L24ACPG
MC78L24ACPRA
MC78L24ACPRAG
24 V
TJ = 0° to +125°C
MC78L24ACPRP
MC78L24ACPRPG
Package
Shipping†
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Units/Bag
TO−92
(Pb−Free)
2000 Units/Bag
TO−92
2000 Tape & Reel
TO−92
(Pb−Free)
2000 Tape & Reel
TO−92
2000 Ammo Pack
TO−92
(Pb−Free)
2000 Ammo Pack
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
13
MC78L00A Series, NCV78L00A
MARKING DIAGRAMS
SOIC−8
D SUFFIX
CASE 751
8
8
8LxxA
ALYWC
G
8LxxA
ALYWB
G
1
1
xx
A
L
Y
W
B, C
G
= 05, 08, 09, 12, or 15
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Temperature Range
= Pb−Free Package
TO−92
P SUFFIX
CASE 029
MC78L
zzABP
ALYWWG
G
MC78L
zzACP
ALYWWG
G
1 2 3
1 2 3
zz
= 05, 08, 09, 12, 15, 18 or 24
A
= Assembly Location
L
= Wafer Lot
Y
= Year
WW = Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
http://onsemi.com
14
MC78L00A Series, NCV78L00A
PACKAGE DIMENSIONS
SOIC−8 NB
D SUFFIX
CASE 751−07
ISSUE AF
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
1
0.25 (0.010)
M
Y
M
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
15
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0 _
8 _
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
MC78L00A Series, NCV78L00A
PACKAGE DIMENSIONS
TO−92 (TO−226)
P SUFFIX
CASE 29−11
ISSUE AL
A
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
B
R
P
L
SEATING
PLANE
K
D
X X
G
J
H
V
C
SECTION X−X
1
N
DIM
A
B
C
D
G
H
J
K
L
N
P
R
V
INCHES
MIN
MAX
0.175
0.205
0.170
0.210
0.125
0.165
0.016
0.021
0.045
0.055
0.095
0.105
0.015
0.020
0.500
−−−
0.250
−−−
0.080
0.105
−−−
0.100
0.115
−−−
0.135
−−−
MILLIMETERS
MIN
MAX
4.45
5.20
4.32
5.33
3.18
4.19
0.407
0.533
1.15
1.39
2.42
2.66
0.39
0.50
12.70
−−−
6.35
−−−
2.04
2.66
−−−
2.54
2.93
−−−
3.43
−−−
N
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
16
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
MC78L00A/D