Features Regulated Converters ● ● ● ● ● ● ● ● 4:1 Wide Input Voltage Range 40 Watts Regulated Output Power 1.6kVDC Isolation Over Current and Over Voltage Protection Six-Sided Shield No Derating to 55°C Standard 2” x2” Package and Pinning Efficiency to 86% Selection Guide 24V and 48V Wide Input Types Part Number Input Range VDC Output Voltage VDC Output Current mA Input (4,5) Current mA Efficiency(6) Capacitive(7) Load max. % µF RP40-243.3SGW 9-36 3.3 10000 80/1677 86 25750 RP40-2405SGW 9-36 5 8000 100/1984 88 13600 RP40-2412SGW 9-36 12 3333 100/1984 88 2360 RP40-2415SGW 9-36 15 2666 110/1984 88 1510 RP40-483.3SGW 18-75 3.3 10000 50/838 86 25750 RP40-4805SGW 18-75 5 8000 50/992 88 13600 RP40-4812SGW 18-75 12 3333 70/992 88 2360 RP40-4815SGW 18-75 15 2666 70/992 88 1510 RP40-2412DGW 9-36 ±12 ±1667 30/1984 88 ±1200 RP40-2415DGW 9-36 ±15 ±1333 30/1984 88 ±750 RP40-4812DGW 18-75 ±12 ±1667 20/992 88 ±1200 RP40-4815DGW 18-75 ±15 ±1333 20/992 88 ±750 POWERLINE DC/DC-Converter RP40S_DGW Series 40 Watt 2” x 2” Single & Dual Output * no suffix for CTRL function with Positive Logic (1=ON, 0=OFF), this is standard * add /N for CTRL function with Negative Logic (0=ON, 1=OFF) Derating Graph (Ambient Temperature) RP40-4805SGW 125 100 1=75Vin, 2=18Vin, 3=48Vin 1 2 3 Output Power (%) 75 50 Nom Vin Natural Convection 25 0 -40 -25 -10 0 40 50 60 70 80 90 100 110 55 Ambient Temperature Range (°C) Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at [email protected] 280 November-2006 www.recom-international.com POWERLINE RP40-S_DGW Series DC/DC-Converter Derating Graph (Ambient Temperature) RP40-4805SGW 125 1=Natural Convection, 2=200LFM, 3=300LFM, 4=400LFM, 5=500LFM 1 100 Output Power (%) 75 50 2 3 45 Natural Convection 25 0 -40 -25 -10 0 40 50 60 70 80 90 100 110 55 Ambient Temperature Range (°C) Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range Undervoltage Protection 24V nominal input 9-36VDC 48V nominal input 18-75VDC 24V Input 48V Input DC-DC ON = 9VDC, DC-DC OFF = 8VDC DC-DC ON = 18VDC, DC-DC OFF = 16VDC Input Filter Pi Type Input Voltage Variation dv/dt (Complies with ETS300 132 part 4.4) 5V/ms max Input Surge Voltage (100 ms max.) 24V Input 50VDC 48V Input 100VDC Input Reflected Ripple (nominal Vin and full load)(see Note 3) 20mAp-p Start Up Time (nominal Vin and constant resistor load) 20ms typ. Remote ON/OFF (see Note 7) (Positiv logic) (Negativ logic) Remote OFF input current DC-DC ON DC-DC OFF DC-DC ON DC-DC OFF Nominal input Output Power Open or 3V < Vr < 12V Short or 0V < Vr < 1.2V Short or 0V < Vr < 1.2V Open or 3V < Vr < 12V 24Vin: 10mA 48Vin: 5mA 40W max. Output Voltage Accuracy (full Load and nominal Vin) ±1% continued on next page www.recom-international.com November-2006 281 RP40-S_DGW Series POWERLINE DC/DC-Converter Specifications, cont. (typical at nominal input and 25°C unless otherwise noted) Voltage Adjustability (see Note 1) Load Regulation (0% to 100% full load) (see Notes 9, 10) Line Regulation (low line, high line at full load) Cross Regulation (see Note 11) Temperature Coefficient Ripple and Noise (20MHz bandwith) ±10% Single Dual ±0.5% ±1% Dual ±0.2% ±5% Single 3.3, 5V Single 12, 15V Dual 12V Dual 15V Transient Response (25% load step change) Over Voltage Protection Zener diode clamp (only single) ±0.02%/°C max. 50mVp-p 75mVp-p 120mVp-p 150mVp-p 250µs 3.3 Vout 5 Vout 12 Vout / ±12 Vout 3.9V 6.2V 15V / ±15V 15 Vout / ±15 Vout 18V / ±18V 150% max. Over Load Protection (% of full load at nominal Vin) Short Circuit Protection Hiccup, automatic recovery Efficiency see „Selection Guide“ table Isolation Voltage 1600VDC min. Isolation Resistance 1 GΩ min. Isolation Capacitance 1500pF max. Operating Frequency 300kHz typ. Operating Temperature Range -40°C to +55°C(without derating) +55°C to +105°C(with derating) Maximum Case Temperature Storage Temperature Range Over Temperature Protection Thermal Impedance (see Note 8) 105°C Without Heat-Sink With Heat-Sink Thermal Shock -55°C to +125°C 115°C typ. 9.2°C/Watt 7.6°C/Watt MIL-STD-810D Vibration 10-55Hz, 10G, 30 Min. along X, Y and Z Relative Humidity 5% to 95% RH Case Material Nickel plated copper Base Material Non-conductive black plastic FR4 Potting Material Conducted Emissions (see Notes 12, 14) Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Epoxy (UL94-V0) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Weight 60g Dimensions MTBF (see Note 2) 51.3 x 51.3 x 10.2mm Bellcore TR-NWT-00332 MIL-STD-217F 282 Class A Class A Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A November-2006 1105 x 103 hours 151 x 103 hours www.recom-international.com RP40-S_DGW Series POWERLINE DC/DC-Converter Notes : 1. For the single output: Maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is not being used, the +sense should be connected to its corresponding +OUTPUT and likewise the -sense should be connected to its corresponding –OUTPUT. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Simulated source impedance of 12µH. 12µH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistive load. 7. The ON/OFF control function. There are positive logic (standard) and negative logic (option). The pin voltage is referenced to negative input To order negative logic ON/OFF control add the suffix-N (Ex: RP40-4805SGW-N). 8. Heat sink is optional and P/N: 7G-0026A. 9. The dual output required a minimum loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 10. Load regulation for dual output : Min load to 100% load balanced on all outputs. 11.Cross regulation for dual output : asymmetrical load 25% / 100% FL. 12..The RP40-GW series required external filter to meets EN55022 class A. 13.Output ripple and noise measured with a 0.1µF/50V MLCC. 14.See application notes for EMI-filtering. Package Style and Pinning (mm) 3rd angle projection 51.30 51.30 10.20 0.70 dia. 1.0 5.6 Pin Connections 45.70 4 5.10 1 2 Bottom View 15.30 28.20 3 5 6 2.5 5.10 Pin # 1 2 3 4 5 6 7 8 Single +Vin -Vin CTRL -SENSE (Note 1) +SENSE (Note 2) +Vout -Vout TRIM Dual +Vin -Vin CTRL +Vout Com Com -Vout TRIM Pin Pitch Tolerance ±0.35 mm 7.6 15.20 20.30 7 External Output Trimming 8 Output can be externally trimmed by using the method shown below. ( ) for dual output trim 7(7) Trim Up 8(8) RD RU 8(8) www.recom-international.com November-2006 Trim Down 6(4) 283