RICOH R2062K01-E2

R2062 SERIES
3 wire interface Real-Time Clock ICs with Battery Backup switch-over Function
NO.EA-178-070910
OUTLINE
The R2062 is a CMOS real-time clock IC connected to the CPU by three signal lines, CE, SCLK, and SIO, and
configured to perform serial transmission of time and calendar data to the CPU. Further, battery backup
switchover circuit and a voltage detector. The periodic interrupt circuit is configured to generate interrupt signals
with six selectable interrupts ranging from 0.5 seconds to 1 month. The 2 alarm interrupt circuits generate
interrupt signals at preset times. As the oscillation circuit is driven under constant voltage, fluctuation of the
oscillator frequency due to supply voltage is small, and the time keeping current is small (TYP. 0.4µA at 3V). The
oscillation halt sensing circuit can be used to judge the validity of internal data in such events as power-on; The
supply voltage monitoring circuit is configured to record a drop in supply voltage below two selectable supply
voltage monitoring threshold settings. The 32.768kHz clock output function (CMOS output) is intended to output
sub-clock pulses for the external microcomputer. The oscillation adjustment circuit is intended to adjust time
counts with high precision by correcting deviations in the oscillation frequency of the quartz crystal unit. Battery
backup switchover function is the automatic switchover circuit between a main power supply and a backup
battery of secondary battery. Since the package for these ICs are FFP12 (2.0x2.0x1.0: R2062Kxx) and
SSOP16 (5.0x6.4x1.25: R2062Sxx (Preliminary)), high density mounting of ICs on boards is possible.
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Minimum Timekeeping supply voltage Typ. 0.75V (Max. 1.00V); VDD pin
Low power consumption
Typ. 0.4µA (Max. 1.0µA) at VDD=3V
Built-in Backup switchover circuit (can be used for a secondary battery, or an electric double layer capacitor)
Three signal lines (CE, SCLK, and SIO) required for connection to the CPU. ·····
(Maximum clock frequency of 1MHz (with VCC = 3V) )
Time counters (counting hours, minutes, and seconds) and calendar counters (counting years, months,
days, and weeks) (in BCD format)
Interrupt circuit configured to generate interrupt signals (with interrupts ranging from 0.5 seconds to 1
month) to the CPU and provided with an interrupt flag and an interrupt halt
2 alarm interrupt circuits (Alarm_W for week, hour, and minute alarm settings and Alarm_D for hour and
minute alarm settings)
Built-in voltage detector with delay
With Power-on flag to prove that the power supply starts from 0V
32-kHz clock output pin (CMOS output. “H” level is always equal to VCC.)
Supply voltage monitoring circuit with two supply voltage monitoring threshold settings
Automatic identification of leap years up to the year 2099
Selectable 12-hour and 24-hour mode settings
Built-in oscillation stabilization capacitors (CG and CD)
High precision oscillation adjustment circuit
CMOS process
Package FFP12 (2.0mm x 2.0mm x 1.0mm : R2062Kxx, SSOP16 (5.0mm x 6.4mm x 1.25mm :
R2062Sxx(Preliminary)),
1
R2062 series
PIN CONFIGURATION
R2062Kxx(FFP12)
INTR
OSCOUT
OSCIN
9
8
7
R2062Sxx(SSOP16)
(Preliminary)
NC
1
16
VCC
VDCC
2
15
VDD
VDD
CLKOUT
3
14
NC
VSS
11
5
VCC
SCLK
4
13
OSCIN
CE
12
4
VDCC
SIO
5
12
OSCOUT
NC
6
11
NC
CE
7
10
CLKOUT
SCLK
SIO
3
6
2
10
1
CIN
VSS
8
9
INTR
CIN
TOP VIEW
TOP VIEW
BLOCK DIAGRAM
C2
MAIN Power
Supply
VDD
R1
VCC
Rechargeable
Battery
BATTERY
VOLTAGE
MONITOR
SW1
C3
VOLTAGE
DETECTOR
VDCC
DELAY
OSCIN
OSCOUT
CE
LEVEL
SHIFTER
REAL
TIME
CLOCK
SCLK
SIO
CLKOUT
CIN
C1
VSS
2
VOLTAGE
REFERENCE
INTR
CPU
R2062 series
SELECTION GUIDE
In the R2062xxx Series, output voltage and options can be designated.
Part Number is designated as follows:
R2062K01-E2 ←Part Number
↑↑ ↑
R2062abb-cc
Code
Description
Designation of the package.
a
K: FFP12
S: SSOP16 (Preliminary)
bb
Serial number of Voltage detector setting etc.
cc
Designation of the taping type. Only E2 is available.
Part Number
R2062K01-E2
R2062K02-E2
(Preliminary)
Package
FFP12
FFP12
-VDET1 (switch-over threshold)
2.70(Typ.)
2.90(Typ.)
DC Electrical
Characteristics
P. 6
P. 7
3
R2062 series
PIN DESCRIPTION
PIN
Symbol
Item
Description
The CE pin is used for interfacing with the CPU. Should
be held high to allow access to the CPU. Incorporates a
pull-down resistor. Should be held low or open when the
CPU is powered off. Allows a maximum input voltage of
5.5 volts regardless of supply voltage.
The SCLK pin is used to input clock pulses synchronizing
the input and output of data to and from the SIO pin.
Allows a maximum input voltage of 5.5 volts regardless of
supply voltage.
The SIO pin is used to input or output data intended for
writing or reading in synchronization with the SCLK pin.
R2062Kxx R2062Sxx
(FFP12) (SSOP16)
4
12
7
CE
Chip enable
Input
2
4
SCLK
Serial
Clock Input
1
5
SIO
9
10
INTR
Serial
Input /
Output
Interrupt
Output
3
3
CLKOUT
5
16
VCC
6
15
VDD
4
2
VDCC
VCC Power
Supply
Monitoring
Result
Output
10
9
CIN
7
13
OSCIN
8
12
OSCOUT
11
8
VSS
-
1,6,11,
14
NC
Noise
Bypass Pin
Oscillation
Circuit Input
Oscillation
Circuit
Output
Negative
Power
Sup Supply
Input
No
Connection
32kHz
Clock
Output
Main
Battery
input
Positive
Power
Supply
Input
The INTR pin is used to output alarm interrupt
(Alarm_W) and alarm interrupt (Alarm_D) and output
periodic interrupt signals to the CPU signals. Disabled at
power-on from 0V. Nch. open drain output.
The CLKOUT pin is used to output 32.768-kHz clock
pulses. CMOS output. “H” level is always equal to VCC.
Supply power to the IC.
The VDD pin is connected to the power supply. Connect a
capacitor as much as 0.1µF between VDD and VSS. In
the case of using a secondary battery, connecting the
secondary battery to this pin is possible.
While monitoring VCC Power supply, if the voltage is
equal or lower than –VDET1, this output level is “L”. When
VDCC becomes “L”, SW1 turns off. When VCC is equal
to +VDET1 or more, SW1 turns on. After t DELAY passed,
VDCC output becomes off, or “H”. Nch Open-drain
output.
To stabilize the internal reference, connect a capacitor as
much as 0.1uF between this pin and VSS.
The OSCIN and OSCOUT pins are used to connect the
32.768-kHz quartz crystal unit (with all other oscillation
circuit components built into the R2062 series).
The VSS pin is grounded.
R2062 series
ABSOLUTE MAXIMUM RATINGS
(VSS=0V)
Symbol
Item
VCC
Supply Voltage 1
VDD
Supply Voltage 2
VI
Input Voltage 1
Input Voltage 2
Input Voltage 3
VO
Output Voltage 1
Output Voltage 2
IOUT
Maximum Output Current
PD
Power Dissipation
Topt
Operating Temperature
Tstg
Storage Temperature
Pin Name
VCC
VDD
CE, SCLK
SIO
CIN
INTR , VDCC
SIO, CLKOUT
VDD
Topt = 25°C
Description
-0.3 to +6.5
-0.3 to +6.5
-0.3 to +6.5
-0.3 to VCC+0.3
-0.3 to VDD+0.3
-0.3 to +6.5
-0.3 to VCC+0.3
10
300
-40 to +85
-55 to +125
Unit
V
V
V
V
V
V
V
mA
mW
°C
°C
RECOMMENDED OPERATING CONDITIONS
Symbol
Vaccess
Item
Supply Voltage
VCLK
Minimum Timekeeping
Voltage
CGout,CDout=0pF
*2), *3)
Oscillation Frequency
Pull-up Voltage
fXT
VPUP
Pin Name
VCC power supply
voltage for interfacing
with CPU
(VSS=0V, Topt=-40 to +85°C)
Min,
Typ.
Max.
Unit
-VDET1
5.5
V
*1)
0.75
1.00
V
32.768
kHz
5.5
V
INTR , VDCC
*1) -VDET1 in Vaccess specification is guaranteed by design.
*2) CGout is connected between OSCIN and VSS, CDout is connected between OSCOUT and VSS.
R2062 series incorporates the capacitors between OSCIN and VSS, between OSCOUT and VSS.
Then normally, CGout and CDout are not necessary.
*3) Quartz crystal unit: CL=6-8pF, R1=30KΩ
5
R2062 series
DC ELECTRICAL CHARACTERISTICS
•
R2062K01
(Unless otherwise specified: VSS=0V, VCC=3.0V, 0.1uF between VDD and VSS, CIN and VSS,
Topt=-40 to +85°C)
Symbol
Item
Pin Name
Conditions
Min.
Typ.
VIH1
“H” Input Voltage 1
CE, SCLK
0.8xVCC
VIH2
“H” Input Voltage 2
SIO
0.8xVCC
VIL
“L” Input Voltage
CE, SIO
-0.3
SCLK
IOH
“H” Output
SIO,
VOH=VCC-0.5V
Current
CLKOUT
IOL1
“L” Output Current 1
SIO,
0.5
VOL=0.4V
CLKOUT
IOL2
“L” Output Current 2
2.0
INTR
VDD, VCC=2.0V
IOL3
“L” Output Current 3
0.5
VDCC
VOL=0.4V
IIL
Input Leakage
SCLK
VI=5.5V or VSS
-1.0
Current
RDNCE
Pull-down Input
CE
40
120
register
IOZ1
Output Off-state
SIO
VO=5.5V or VSS
-1.0
Current 1
VO=5.5V or VSS
IOZ2
Output Off-state
-1.0
INTR ,
Current 2
VDCC
IDD
Time Keeping Current
VDD
VCC=0V, VDD=3.0V,
0.4
at Backup mode
Output=OPEN
Time Keeping
VDETH
Supply Voltage
VDD
VCC=0V,
1.90
2.10
Monitoring Voltage “H”
Topt=+25°C
VDETL
Supply Voltage
VDD
VCC=0V,
1.20
1.35
Monitoring Voltage “L”
Topt=25°C
-VDET1
Detector Threshold
VCC
2.63
2.70
Topt=25°C
Voltage
(falling edge of VCC)
+VDET1
Detector Released
VCC
2.69
2.78
Topt=25°C
Voltage (rising edge of
VCC)
Detector Threshold
VCC, VDD
Topt=-40 to 85°C
±100
∆VDET
and
Released
Voltage
*1)
∆Topt
Temperature coefficient
VDDOUT1
CG
VDD Output
Voltage 1
Internal Oscillation
Capacitance 1
CD
Internal Oscillation
Capacitance 2
*1) Guaranteed by design.
6
VDD
VCC0.12
Max.
5.5
VCC+0.3
0.2xVCC
-0.5
Unit
V
mA
mA
1.0
µA
400
kΩ
1.0
µA
1.0
µA
1.0
µA
2.30
V
1.50
V
2.77
V
2.87
V
ppm
/°C
VCC0.04
V
OSCIN
10
pF
OSCOUT
10
Topt=25°C, VCC=3.0V,
Iout=1.0mA
R2062 series
•
R2062K02(Preliminary)
(Unless otherwise specified: VSS=0V, VCC=3.3V, 0.1uF between VDD and VSS, CIN and VSS,
Topt=-40 to +85°C)
Symbol
Item
Pin Name
Conditions
Min.
Typ.
Max.
VIH1
“H” Input Voltage 1
CE, SCLK
0.8xVCC
5.5
VIH2
“H” Input Voltage 2
SIO
0.8xVCC
VCC+0.3
VIL
“L” Input Voltage
CE, SIO
-0.3
0.2xVCC
SCLK
IOH
“H” Output
SIO,
VOH=VCC-0.5V
-0.5
Current
CLKOUT
IOL1
“L” Output Current 1
SIO,
0.5
VOL=0.4V
CLKOUT
IOL2
“L” Output Current 2
2.0
INTR
V
IOL3
“L” Output Current 3
DD
,
V
CC
=2.0V
0.5
VDCC
VOL=0.4V
IIL
Input Leakage
SCLK
VI=5.5V or VSS
-1.0
1.0
Current
RDNCE
Pull-down Input
CE
40
120
400
register
IOZ1
Output Off-state
SIO
VO=5.5V or VSS
-1.0
1.0
Current 1
VO=5.5V or VSS
IOZ2
Output Off-state
-1.0
1.0
INTR ,
Current 2
VDCC
IDD
Time Keeping Current
VDD
VCC=0V, VDD=3.0V,
0.4
1.0
at Backup mode
Output=OPEN
Time Keeping
VDETH
Supply Voltage
VDD
VCC=0V,
1.90
2.10
2.30
Monitoring Voltage “H”
Topt=+25°C
VDETL
Supply Voltage
VDD
VCC=0V,
1.20
1.35
1.50
Monitoring Voltage “L”
Topt=25°C
-VDET1
Detector Threshold
VCC
2.820
2.900
2.980
Topt=25°C
Voltage
(falling edge of VCC)
+VDET1
Detector Released
VCC
2.890
2.985
3.080
Topt=25°C
Voltage (rising edge of
VCC)
Detector Threshold
VCC, VDD
±100
∆VDET
Topt=-40 to 85°C
and
Released
Voltage
*1)
∆Topt
Temperature coefficient
VDDOUT1
CG
VDD Output
Voltage 1
Internal Oscillation
Capacitance 1
CD
Internal Oscillation
Capacitance 2
*1) Guaranteed by design.
VDD
VCC0.12
Unit
V
mA
mA
µA
kΩ
µA
µA
µA
V
V
V
V
ppm
/°C
VCC0.04
V
OSCIN
10
pF
OSCOUT
10
Topt=25°C, VCC=3.3V,
Iout=1.0mA
7
R2062 series
AC ELECTRICAL CHARACTERISTICS
Unless otherwise specified: VSS=0V,Topt=-40 to +85°C
Input and Output Conditions: VIH=0.8×VCC,VIL=0.2×VCC,VOH=0.8×VCC,VOL=0.2×VCC,CL=50pF
Sym
Item
CondiUnit
VDD≥1.7V *1)
-bol
Tions
Min.
Typ.
Max.
tCES
CE Set-up Time
400
ns
tCEH
CE Hold Time
400
ns
tCR
CE Recovery Time
62
µs
fSCLK
SCLK Clock Frequency
1.0
MHz
tCKH
SCLK Clock ”H” Time
400
ns
tCKL
SCLK Clock ”L” Time
400
ns
tCKS
SCLK Set-up Time
200
ns
tRD
Data Output Delay Time
300
ns
tRZ
Data Output Floating Time
300
ns
tCEZ
Data Output Delay Time After
300
ns
Falling of CE
tDS
Input Data Set-up Time
200
ns
tDH
Input Data Hold Time
200
ns
Time
tDELAY
Output Delay Time of Voltage
100
105
110
ms
Keeping
Detector
*1) VCC voltage interfacing with CPU is defined by Vaccess (P.5 RECOMMENDED OPERATING
CONDITIONS)
*) For reading/writing timing, see “P.29 Interfacing with the CPU •Considerations in Reading and
Writing Time Data under special condition”.
tCKH
tCKL
CE
tCEH
tCKS
tCR
tCES
SCLK
tDS
tDH
tCEZ
SIO(write cycle)
SIO(read cycle)
tRD
VCC
+VDET1
tDELAY
VDCC
8
tRD
tRZ
R2062 series
PACKAGE DIMENSIONS
R2062Kxx
9
7
6
10
1PIN INDEX
12
0.2±0.15
0.35
0.25
1.0Max
2.0±0.1
3
2PIN INDEX
0.35
0.3±0.15
0.103
0.5
0.05
4
1
0.5
•
(BOTTOM VIEW)
0.17±0.1
0.27±0.15
2.0±0.1
unit: mm
9
R2062 series
•
R2062Sxx (Preliminary)
0 to 10°
5.0±0.3
16
8
1
0.15
+0.1
-0.05
1.15±0.1
0.65
0.1±0.1
0.225typ
0.10
+0.1
0.22 -0.05
0.5±0.3
6.4±0.3
4.4±0.2
9
0.15
M
unit: mm
TAPING SPECIFICATION
The R2062 Series have one designated taping direction. The product designation for the taping components is
"R2062S/Kxx-E2".
10
R2062 series
GENERAL DESCRIPTION
•
Battery Backup Switchover Function
The R2062 Series have two power supply input, or VCC and VDD. With monitoring VCC pin input voltage, which
voltage between the two is supplied to the internal power supply is decided.
Refer to the next table to see the state of the backup battery and internal power supply’s state of the IC by each
condition.
VCC≥VDET1
VCC<VDET1
VCC→RTC, VDD
VDD→RTC
VDCC =OFF(H)
VDCC =L
As a backup battery, not only a secondary battery such as ML614, TC616, but also an electric double layered
capacitor or an aluminum capacitor can be used. The case of back-up by primary battery, the external diode
must be connected below.
The case of back-up by
capacitor or secondary battery
(Charging voltage is equal to CPU
power supply voltage)
VCC
CPU power
supply
The case of back-up by
primary battery
VCC
CPU Power
Supply
VDD
VDD
0.1µF
0.1µF
CR2025
etc.
ML614
etc.
VSS
VSS
•
Interface with CPU
The R2062 is connected to the CPU by three signal lines CE (Chip Enable), SCLK (Serial Clock), and SIO
(Serial Input / Output), through which it reads and writes data from and to the CPU. The CPU can be accessed
when the CE pin is held high. Access clock pulses have a maximum frequency of 1 MHz, allowing high-speed
data transfer to the CPU. VCC falls down under -VDET1, the R2062 stops accessing with CPU.
11
R2062 series
•
Clock and Calendar Function
The R2062 reads and writes time data from and to the CPU in units ranging from seconds to the last two digits of
the calendar year. The calendar year will automatically be identified as a leap year when its last two digits are a
multiple of 4. Consequently, leap years up to the year 2099 can automatically be identified as such.
*) The year 2000 is a leap year while the year 2100 is not a leap year.
•
Alarm Function
The R2062 incorporates the alarm interrupt circuit configured to generate interrupt signals to the CPU at preset
times. The alarm interrupt circuit allows two types of alarm settings specified by the Alarm_W registers and the
Alarm_D registers. The Alarm_W registers allow week, hour, and minute alarm settings including combinations
of multiple day-of-week settings such as "Monday, Wednesday, and Friday" and "Saturday and Sunday". The
Alarm_D registers allow hour and minute alarm settings. The Alarm_W outputs from INTR pin, and the
Alarm_D outputs also from INTR pin. Each alarm function can be checked from the CPU by using a polling
function.
•
High-precision Oscillation Adjustment Function
The R2062 has built-in oscillation stabilization capacitors (CG and CD), that can be connected to an external
quartz crystal unit to configure an oscillation circuit. Two kinds of accuracy for this function are alternatives. To
correct deviations in the oscillator frequency of the crystal, the oscillation adjustment circuit is configured to allow
correction of a time count gain or loss (up to ±1.5ppm or ±0.5ppm at 25°C) from the CPU. The maximum range is
approximately ±189ppm (or ±63ppm) in increments of approximately 3ppm (or 1ppm). Such oscillation
frequency adjustment in each system has the following advantages:
* Allows timekeeping with much higher precision than conventional RTCs while using a quartz crystal unit with
a wide range of precision variations.
* Corrects seasonal frequency deviations through seasonal oscillation adjustment.
* Allows timekeeping with higher precision particularly with a temperature sensing function out of RTC, through
oscillation adjustment in tune with temperature fluctuations.
•
Power-on Reset, Oscillation Halt Sensing Function and Supply Voltage Monitoring Function
The R2062 has 2 power supply pins (VCC, VDD), among them, VCC pin and VDD pin have monitoring function
of supply voltage. VCC power supply monitoring circuit makes VDCC pin “L” when VCC power supply pin
becomes equal or lower than –VDET1. At the power-on of VCC, this circuit makes VDCC pin turn off, or “H”
after the delay time, tDELAY from when the VCC power supply pin becomes equal or more than +VDET1.
The R2062 incorporates an oscillation halt sensing circuit equipped with internal registers configured to record
any past oscillation halt, the oscillation halt sensing circuit, VDD monitoring flag, and power-on reset flag are
useful for judging the validity of time data.
Power on reset function reset the control resisters when the system is powered on from 0V. At the same time, the
fact is memorized to the resister as a flag, thereby identifying whether they are powered on from 0V or battery
backed-up.
The R2062 also incorporates a supply voltage monitoring circuit equipped with internal registers configured to
record any drop in supply voltage below a certain threshold value. Supply voltage monitoring threshold settings
can be selected between 2.1V and 1.35V through internal register settings. The sampling rate is normally 1s.
12
R2062 series
The oscillation halt sensing circuit is configured to confirm the established invalidation of time data in contrast to
the supply voltage monitoring circuit intended to confirm the potential invalidation of time data. Further, the
supply voltage monitoring circuit can be applied to battery supply voltage monitoring.
•
Periodic Interrupt Function
The R2062 incorporates the periodic interrupt circuit configured to generate periodic interrupt signals aside from
interrupt signals generated by the periodic interrupt circuit for output from the INTR pin. Periodic interrupt
signals have five selectable frequency settings of 2 Hz (once per 0.5 seconds), 1 Hz (once per 1 second), 1/60
Hz (once per 1 minute), 1/3600 Hz (once per 1 hour), and monthly (the first day of every month). Further,
periodic interrupt signals also have two selectable waveforms, a normal pulse form (with a frequency of 2 Hz or 1
Hz) and special form adapted to interruption from the CPU in the level mode (with second, minute, hour, and
month interrupts). The condition of periodic interrupt signals can be monitored with using a polling function.
•
32kHz Clock Output
The R2062 incorporates a 32-kHz clock circuit configured to generate clock pulses with the oscillation frequency
of a 32.768kHz quartz crystal unit for output from the CLKOUT pin (CMOS push-pull output). The 32-kHz clock
output is always enabled and the “H” level of the CLKOUT pin is same as VCC power supply.
13
R2062 series
Address Mapping
Address
A3A2A1A0
0
0000
Register Name
Second Counter
1
2
0001
0010
Minute Counter
Hour Counter
3
4
5
0011
0100
0101
6
7
0110
0111
8
1000
9
1001
A
1010
B
1011
C
1100
D
E
1101
1110
Control Register 1 *3)
F
1111
Control Register 2 *3)
Day-of-week Counter
Day-of-month Counter
Month Counter and
Century Bit
Year Counter
Oscillation Adjustment
Register *3)
Alarm_W
(Minute Register)
Alarm_W
(Hour Register)
Alarm_W
(Day-of-week Register)
Alarm_D
(Minute Register)
Alarm_D
(Hour Register)
D a
D4
S10
t a
D3
S8
D2
S4
D1
S2
D0
S1
M10
H10
M8
H8
M4
H4
M2
H2
M1
H1
D10
MO10
D8
MO8
W4
D4
MO4
W2
D2
MO2
W1
D1
MO1
Y20
F5
Y10
F4
Y8
F3
Y4
F2
Y2
F1
Y1
F0
WM40
WM20
WM10
WM8
WM4
WM2
WM1
-
-
WH10
WH8
WH4
WH2
WH1
-
WW6
WH20
WP/ A
WW5
WW4
WW3
WW2
WW1
WW0
-
DM40
DM20
DM10
DM8
DM4
DM2
DM1
-
-
DH10
DH8
DH4
DH2
DH1
WALE
DH20
DP/ A
DALE
12 /24
TEST
CT2
CT1
CT0
VDSL
VDET
SCRA
TCH2
PON
*5)
SCRA
TCH1
CTFG
WAFG
DAFG
D7
*2)
-
D6
S40
D5
S20
M40
-
19 /20
-
M20
H20
P/ A
D20
-
Y80
DEV
*4)
-
Y40
F6
XST
Notes:
* 1) All the data listed above accept both reading and writing.
* 2) The data marked with "-" is invalid for writing and reset to 0 for reading.
* 3) When the PON bit is set to 1 in Control Register 2, all the bits are reset to 0 in Oscillation Adjustment
Register, Control Register 1 and Control Register 2 excluding the XST bit.
* 4) When DEV=0, the oscillation adjustment circuit is configured to allow correction of a time count gain
or loss up to ±1.5ppm.
When DEV=1, the oscillation adjustment circuit is configured to allow correction of a time count gain
or loss up to or ±0.5ppm.
* 5) PON is a power-on-reset flag.
14
R2062 series
Register Settings
•
Control Register 1 (ADDRESS Eh)
D7
WALE
D6
DALE
D4
D3
D2
D1
D0
SCRA
TEST
CT2
CT1
CT0
(For Writing)
TCH2
SCRA
TEST
CT2
CT1
CT0
(For Reading)
WALE
DALE
12 /24
TCH2
0
0
0
0
0
0
0
0
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
(1) WALE, DALE
WALE,DALE
0
1
D5
12 /24
Alarm_W Enable Bit, Alarm_D Enable Bit
Description
Disabling the alarm interrupt circuit (under the control of the settings
of the Alarm_W registers and the Alarm_D registers).
Enabling the alarm interrupt circuit (under the control of the settings
of the Alarm_W registers and the Alarm_D registers)
12 /24-hour Mode Selection Bit
Description
12 /24
0
Selecting the 12-hour mode with a.m. and p.m. indications.
1
Selecting the 24-hour mode
Setting the 12 /24 bit to 0 and 1 specifies the 12-hour mode and the 24-hour mode, respectively.
(Default)
(2) 12 /24
24-hour mode
12-hour mode
24-hour mode
00
12 (AM12)
12
01
01 (AM 1)
13
02
02 (AM 2)
14
03
03 (AM 3)
15
04
04 (AM 4)
16
05
05 (AM 5)
17
06
06 (AM 6)
18
07
07 (AM 7)
19
08
08 (AM 8)
20
09
09 (AM 9)
21
10
10 (AM10)
22
11
11 (AM11)
23
Setting the 12 /24 bit should precede writing time data
(3) SCRATCH2
(Default)
12-hour mode
32 (PM12)
21 (PM 1)
22 (PM 2)
23 (PM 3)
24 (PM 4)
25 (PM 5)
26 (PM 6)
27 (PM 7)
28 (PM 8)
29 (PM 9)
30 (PM10)
31 (PM11)
Scratch Bit 2
SCRATCH2
Description
0
1
The SCRATCH2 bit is intended for scratching and accepts the reading and writing of 0 and 1.
The SCRATCH2 bit will be set to 0 when the PON bit is set to 1 in the Control Register 1.
(Default)
15
R2062 series
(4) TEST
Test Bit
TEST
Description
0
Normal operation mode.
1
Test mode.
The TEST bit is used only for testing in the factory and should normally be set to 0.
(5) CT2,CT1, and CT0
CT2
CT1
(Default)
Periodic Interrupt Selection Bits
CT0
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
Wave form
mode
Pulse Mode
*1)
Pulse Mode
*1)
Level Mode
*2)
Level Mode
*2)
Level Mode
*2)
Level Mode
*2)
Description
Interrupt Cycle and Falling Timing
OFF(H)
Fixed at “L”
2Hz(Duty50%)
(Default)
1Hz(Duty50%)
Once per 1 second (Synchronized with
second counter increment)
Once per 1 minute (at 00 seconds of
every minute)
Once per hour (at 00 minutes and 00
seconds of every hour)
Once per month (at 00 hours, 00 minutes,
and 00 seconds of first day of every
month)
* 1) Pulse Mode: 2-Hz and 1-Hz clock pulses are output in synchronization with the increment of the
second counter as illustrated in the timing chart below.
CTFG Bit
IN TR
Pin
Approx. 92µs
(Increment of second counter)
Rewriting of the second counter
In the pulse mode, the increment of the second counter is delayed by approximately 92 µs from the falling
edge of clock pulses. Consequently, time readings immediately after the falling edge of clock pulses may
appear to lag behind the time counts of the real-time clocks by approximately 1 second. Rewriting the
second counter will reset the other time counters of less than 1 second, driving the INTR pin low.
* 2) Level Mode: Periodic interrupt signals are output with selectable interrupt cycle settings of 1 second,
1 minute, 1 hour, and 1 month. The increment of the second counter is synchronized with the falling
edge of periodic interrupt signals. For example, periodic interrupt signals with an interrupt cycle setting
of 1 second are output in synchronization with the increment of the second counter as illustrated in the
timing chart below.
16
R2062 series
CTFG Bit
IN T R
Pin
Setting CTFG bit to 0
(Increment of
second counter)
(Increment of
second counter)
Setting CTFG bit to 0
(Increment of
second counter)
*1), *2) When the oscillation adjustment circuit is used, the interrupt cycle will fluctuate once per 20sec. or
60sec. as follows:
Pulse Mode: The “L” period of output pulses will increment or decrement by a maximum of ±3.784 ms. For
example, 1-Hz clock pulses will have a duty cycle of 50 ±0.3784%.
Level Mode: A periodic interrupt cycle of 1 second will increment or decrement by a maximum of
±3.784 ms.
17
R2062 series
•
Control Register 2 (Address Fh)
D7
VDSL
D6
VDET
D3
D2
D1
D0
SCRA
CTFG
WAFG
DAFG
(For Writing)
TCH1
PON
SCRA
CTFG
WAFG
DAFG
(For Reading)
VDSL
VDET
XST
TCH1
Indefinite
0
0
1
0
0
0
0
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
(1) VDSL
D5
XST
D4
PON
VDD Supply Voltage Monitoring Threshold Selection Bit
VDSL
Description
Selecting the VDD supply voltage monitoring threshold setting of 2.1v.
Selecting the VDD supply voltage monitoring threshold setting of
1.35v.
The VDSL bit is intended to select the VDD supply voltage monitoring threshold settings.
0
1
(2) VDET
(Default)
Supply Voltage Monitoring Result Indication Bit
VDET
Description
Indicating supply voltage above the supply voltage monitoring
(Default)
threshold settings.
1
Indicating supply voltage below the supply voltage monitoring
threshold settings.
Once the VDET bit is set to 1, the supply voltage monitoring circuit will be disabled while the VDET bit will
hold the setting of 1. The VDET bit accepts only the writing of 0, which restarts the supply voltage
monitoring circuit. Conversely, setting the VDET bit to 1 causes no event.
0
(3) XST
Oscillation Halt Sensing Monitor Bit
Description
XST
Sensing a halt of oscillation
0
Sensing a normal condition of oscillation
1
The XST accepts the reading and writing of 0 and 1. The XST bit will be set to 0 when the oscillation
halt sensing. The XST bit will hold 0 even after the restart of oscillation.
(4) PON
Power-on-reset Flag Bit
PON
Description
0
Normal condition
1
Detecting VDD power-on -reset
The PON bit is for sensing power-on reset condition.
(Default)
* The PON bit will be set to 1 when VDD power-on from 0 volts. The PON bit will hold the setting of 1 even
after power-on.
* When the PON bit is set to 1, all bits will be reset to 0, in the Oscillation Adjustment Register, Control
Register 1, and Control Register 2, except XST and PON. As a result, INTR pin stops outputting.
* The PON bit accepts only the writing of 0. Conversely, setting the PON bit to 1 causes no event.
18
R2062 series
(5) SCRATCH1
Scratch Bit 1
SCRATCH1
Description
0
(Default)
1
The SCRATCH1 bit is intended for scratching and accepts the reading and writing of 0 and 1. The
SCRATCH1 bit will be set to 0 when the PON bit is set to 1 in the Control Register 2.
(6) CTFG
Periodic Interrupt Flag Bit
CTFG
Description
0
Periodic interrupt output = “H”
(Default)
1
Periodic interrupt output = “L”
The CTFG bit is set to 1 when the periodic interrupt signals are output from the INTR pin (“L”). The
CTFG bit accepts only the writing of 0 in the level mode, which disables (“H”) the INTR pin until it is
enabled (“L”) again in the next interrupt cycle. Conversely, setting the CTFG bit to 1 causes no event.
(7) WAFG,DAFG
Alarm_W Flag Bit and Alarm_D Flag Bit
WAFG,DAFG
Description
0
Indicating a mismatch between current time and preset alarm time
(Default)
1
Indicating a match between current time and preset alarm time
The WAFG and DAFG bits are valid only when the WALE and DALE have the setting of 1, which is caused
approximately 61µs after any match between current time and preset alarm time specified by the Alarm_W
registers and the Alarm_D registers. The WAFG (DAFG) bit accepts only the writing of 0. INTR pin
outputs off (“H”) when this bit is set to 0. And INTR pin outputs “L” again at the next preset alarm time.
Conversely, setting the WAFG and DAFG bits to 1 causes no event. The WAFG and DAFG bits will have
the reading of 0 when the alarm interrupt circuit is disabled with the WALE and DALE bits set to 0. The
settings of the WAFG and DAFG bits are synchronized with the output of the INTR pin as shown in the
timing chart below.
Approx. 61µs
Approx. 61µs
WAFG(DAFG) Bit
IN TR Pin
Writing of 0 to
WAFG(DAFG) bit
Writing of 0 to
WAFG(DAFG) bit
(Match between
(Match between
(Match between
current time and
current time and
current time and
preset alarm time)
preset alarm time)
preset alarm time)
19
R2062 series
•
Time Counter (Address 0-2h)
Second Counter (Address 0h)
D7
D6
D5
D4
D3
D2
D1
D0
S40
S20
S10
S8
S4
S2
S1
0
S40
S20
S10
S8
S4
S2
S1
0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite
(For Writing)
(For Reading)
Default Settings *)
Minute Counter (Address 1h)
D7
D6
D5
D4
D3
D2
D1
D0
M40
M20
M10
M8
M4
M2
M1
0
M40
M20
M10
M8
M4
M2
M1
0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite
(For Writing)
(For Reading)
Default Settings *)
Hour Counter (Address 2h)
D7
D6
D5
D4
D3
D2
D1
D0
-
-
P/ A
H10
H8
H4
H2
H1
(For Writing)
H10
H8
H4
H2
H1
(For Reading)
or H20
0
0
P/ A
or H20
0
0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* Time digit display (BCD format) as follows:
The second digits range from 00 to 59 and are carried to the minute digit in transition from 59 to 00.
The minute digits range from 00 to 59 and are carried to the hour digits in transition from 59 to 00.
The hour digits range as shown in "P15 • Control Register 1 (ADDRESS Eh) (2) 12 /24: 12 /24-hour
Mode Selection Bit" and are carried to the day-of-month and day-of-week digits in transition from PM11 to
AM12 or from 23 to 00.
* Any writing to the second counter resets divider units of less than 1 second.
* Any carry from lower digits with the writing of non-existent time may cause the time counters to
malfunction. Therefore, such incorrect writing should be replaced with the writing of existent time data.
20
R2062 series
•
Day-of-week Counter (Address 3h)
D7
D6
D5
D4
D3
D2
D1
D0
W4
W2
W1
(For Writing)
0
0
0
0
0
W4
W2
W1
(For Reading)
0
0
0
0
0
Indefinite Indefinite Indefinite
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* The day-of-week counter is incremented by 1 when the day-of-week digits are carried to the day-of-month
digits.
* Day-of-week display (incremented in septimal notation):
(W4, W2, W1) = (0, 0, 0) → (0, 0, 1)→…→(1, 1, 0) → (0, 0, 0)
* Correspondences between days of the week and the day-of-week digits are user-definable
(e.g. Sunday = 0, 0, 0)
* The writing of (1, 1, 1) to (W4, W2, W1) is prohibited except when days of the week are unused.
•
Calendar Counter (Address 4-6h)
Day-of-month Counter (Address 4h)
D7
D6
D5
D4
D3
D2
D1
D0
D20
D10
D8
D4
D2
D1
0
0
D20
D10
D8
D4
D2
D1
0
0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite
(For Writing)
(For Reading)
Default Settings *)
Month Counter + Century Bit (Address 5h)
D7
D6
D5
D4
D3
D2
D1
D0
19 /20
-
-
MO10
MO8
MO4
MO2
MO1
19 /20
Indefinite
0
0
0
0
(For Writing)
MO10
MO8
MO4
MO2
MO1
(For Reading)
Indefinite Indefinite Indefinite Indefinite Indefinite Default Settings *)
Year Counter (Address 6h)
D7
D6
D5
D4
D3
D2
D1
D0
Y80
Y40
Y20
Y10
Y8
Y4
Y2
Y1
(For Writing)
Y80
Y40
Y20
Y10
Y8
Y4
Y2
Y1
(For Reading)
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* The calendar counters are configured to display the calendar digits in BCD format by using the automatic
calendar function as follows:
The day-of-month digits (D20 to D1) range from 1 to 31 for January, March, May, July, August, October,
and December; from 1 to 30 for April, June, September, and November; from 1 to 29 for February in leap
years; from 1 to 28 for February in ordinary years. The day-of-month digits are carried to the month
digits in reversion from the last day of the month to 1. The month digits (MO10 to MO1) range from 1 to
12 and are carried to the year digits in reversion from 12 to 1.
21
R2062 series
The year digits (Y80 to Y1) range from 00 to 99 (00, 04, 08, …, 92, and 96 in leap years) and are carried to
the 19 /20 digits in reversion from 99 to 00.
The 19 /20 digits cycle between 0 and 1 in reversion from 99 to 00 in the year digits.
* Any carry from lower digits with the writing of non-existent calendar data may cause the calendar
counters to malfunction. Therefore, such incorrect writing should be replaced with the writing of existent
calendar data.
•
Oscillation Adjustment Register (Address 7h)
D7
D6
D5
D4
D3
D2
D1
D0
DEV
F6
F5
F4
F3
F2
F1
F0
(For Writing)
DEV
F6
F5
F4
F3
F2
F1
F0
(For Reading)
0
0
0
0
0
0
0
0
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
DEV bit
When DEV is set to 0, the Oscillation Adjustment Circuit operates 00, 20, 40 seconds.
When DEV is set to 1, the Oscillation Adjustment Circuit operates 00 seconds.
F6 to F0 bits
The Oscillation Adjustment Circuit is configured to change time counts of 1 second on the basis of
the settings of the Oscillation Adjustment Register at the timing set by DEV.
*
The Oscillation Adjustment Circuit will not operate with the same timing (00, 20, or 40 seconds)
as the timing of writing to the Oscillation Adjustment Register.
*
The F6 bit setting of 0 causes an increment of time counts by ((F5, F4, F3, F2, F1, F0) - 1) x 2.
The F6 bit setting of 1 causes a decrement of time counts by (( F5,F4,F3,F2,F1,F0 ) + 1) x 2.
The settings of "*, 0, 0, 0, 0, 0, *" ("*" representing either "0" or "1") in the F6, F5, F4, F3, F2, F1, and
F0 bits cause neither an increment nor decrement of time counts.
Example:
If (DEV, F6, F5, F4, F3, F2, F1, F0) is set to (0, 0, 0, 0, 0, 1, 1, 1), when the second digits read 00, 20, or
40, an increment of the current time counts of 32768 + (7 - 1) x 2 to 32780 (a current time count loss).
If (DEV, F6, F5, F4, F3, F2, F1, F0) is set to (0, 0, 0, 0, 0, 0, 0, 1), when the second digits read 00, 20, 40,
neither an increment nor a decrement of the current time counts of 32768.
If (DEV, F6, F5, F4, F3, F2, F1, F0) is set to (1, 1, 1, 1, 1, 1, 1, 0), when the second digits read 00, a
decrement of the current time counts of 32768 + (- 2) x 2 to 32764 (a current time count gain).
An increase of two clock pulses once per 20 seconds causes a time count loss of approximately 3 ppm (2 /
(32768 x 20 = 3.051 ppm). Conversely, a decrease of two clock pulses once per 20 seconds causes a
time count gain of 3 ppm. Consequently, when DEV is set to “0”, deviations in time counts can be
corrected with a precision of ±1.5 ppm. In the same way, when DEV is set to “1”, deviations in time
counts can be corrected with a precision of ±0.5 ppm. Note that the oscillation adjustment circuit is
configured to correct deviations in time counts and not the oscillation frequency of the 32.768-kHz clock
pulses. For further details, see "P34 Configuration of Oscillation Circuit and Correction of Time
Count Deviations • Oscillation Adjustment Circuit".
22
R2062 series
•
Alarm_W Registers (Address 8-Ah)
Alarm_W Minute Register (Address 8h)
D7
D6
D5
D4
WM40
WM20
WM10
0
WM40
WM20
WM10
Indefinite
Indefinite
Indefinite
0
D3
WM8
WM8
D2
WM4
WM4
D1
WM2
WM2
D0
WM1
WM1
Indefinite
Indefinite
Indefinite
Indefinite
Alarm_W Hour Register (Address 9h)
D7
D6
D5
D4
D3
D2
D1
D0
WH20
WH10
WH8
WH4
WH2
WH1
WP/ A
WH10
WH8
WH4
WH2
WH1
0
0
WH20
WP/ A
0
0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite
(For Writing)
(For Reading)
Default Settings *)
(For Writing)
(For Reading)
Default Settings *)
Alarm_W Day-of-week Register (Address Ah)
D7
D6
D5
D4
D3
D2
D1
D0
-
WW6
WW5
WW4
WW3
WW2
WW1
WW0
0
0
WW6
WW5
WW4
WW3
WW2
WW1
WW0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite
(For Writing)
(For Reading)
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* The D5 bit of the Alarm_W Hour Register represents WP/ A when the 12-hour mode is selected (0 for
a.m. and 1 for p.m.) and WH20 when the 24-hour mode is selected (tens in the hour digits).
* The Alarm_W Registers should not have any non-existent alarm time settings.
(Note that any mismatch between current time and preset alarm time specified by the Alarm_W registers
may disable the alarm interrupt circuit.)
* When the 12-hour mode is selected, the hour digits read 12 and 32 for 0 a.m. and 0 p.m., respectively.
(See "P15 •Control Register 1 (ADDRESS Eh) (2) 12 /24: 12 /24-hour Mode Selection Bit")
* WW0 to WW6 correspond to W4, W2, and W1 of the day-of-week counter with settings ranging from (0, 0,
0) to (1, 1, 0).
* WW0 to WW6 with respective settings of 0 disable the outputs of the Alarm_W Registers.
23
R2062 series
Example of Alarm Time Setting
Alarm
Preset alarm time
00:00 a.m. on all days
01:30 a.m. on all days
11:59 a.m. on all days
00:00 p.m. on Mon. to
Fri.
01:30 p.m. on Sun.
11:59 p.m.
on Mon. ,Wed., and Fri.
Sun.
Day-of-week
Mon.
Tue.
Wed.
Th.
12-hour mode
Fri.
Sat.
WW0 WW1 WW2 WW3 WW4 WW5 WW6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
1
1
0
1
0
0
1
0
0
0
1
0
0
0
1
0
0
10
hr.
24-hour mode
1 10
1
10 1
hr. min. min. hr. hr.
10
1
min. min.
1
0
1
3
2
1
1
2
0
3
5
0
0
0
9
0
0
0
1
1
0
1
1
2
0
3
5
0
0
0
9
0
2
3
1
1
3
5
0
9
1
2
3
3
3
5
0
9
Note that the correspondence between WW0 to WW6 and the days of the week shown in the above table is
only an example and not mandatory.
•
Alarm_D Register (Address B-Ch)
Alarm_D Minute Register (Address Bh)
D7
D6
D5
D4
D3
D2
D1
D0
DM40
DM20
DM10
DM8
DM4
DM2
DM1
0
DM40
DM20
DM10
DM8
DM4
DM2
DM1
0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite
(For Writing)
(For Reading)
Default Settings *)
Alarm_D Hour Register (Address Ch)
D7
D6
D5
D4
D3
D2
D1
D0
DH20
DH10
DH8
DH4
DH2
DH1
(For Writing)
DP/ A
DH10
DH8
DH4
DH2
DH1
(For Reading)
0
0
DH20
DP/ A
0
0
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* The D5 bit represents DP/ A when the 12-hour mode is selected (0 for a.m. and 1 for p.m.) and DH20
when the 24-hour mode is selected (tens in the hour digits).
* The Alarm_D registers should not have any non-existent alarm time settings.
(Note that any mismatch between current time and preset alarm time specified by the Alarm_D registers
may disable the alarm interrupt circuit.)
* When the 12-hour mode is selected, the hour digits read 12 and 32 for 0a.m. and 0p.m., respectively.
(See "P15 •Control Register 1 (ADDRESS Eh) (2) 12 /24: 12 /24-hour Mode Selection Bit")
24
R2062 series
Interfacing with the CPU
•
DATA TRANSFER FORMATS
(1) Timing Between CE Pin Transition and Data Input / Output
The R2062 adopts a 3-wire serial interface by which they use the CE (Chip Enable), SCLK (Serial Clock), and
SIO (Serial Input/Output) pins to receive and send data to and from the CPU. The 3-wire serial interface
provides two types of input/output timings with which the SIO pin output and input are synchronized with the
rising or falling edges of the SCLK pin input, respectively, and vice versa. The R2062 is configured to select
either one of two different input/output timings depending on the level of the SCLK pin in the low to high transition
of the CE pin. Namely, when the SCLK pin is held low in the low to high transition of the CE pin, the models will
select the timing with which the SIO pin output is synchronized with the rising edge of the SCLK pin input, and
the input is synchronized with the falling edge of the SCLK pin input, as illustrated in the timing chart below.
CE
tCES
SCLK
tDS
tDH
tRD
SIO (for writing)
SIO (for reading)
Conversely, when the SCLK pin is held high in the low to high transition of the CE pin, the models will select the
timing with which the SIO pin output is synchronized with the falling edge of the SCLK pin input, and the input is
synchronized with the rising edge of the SCLK pin input, as illustrated in the timing chart below.
CE
tCES
SCLK
tDS
SIO (for writing)
tDH
tRD
SIO (for reading)
25
R2062 series
(2) Data Transfer Formats
Data transfer is commenced in the low to high transition of the CE pin input and completed in its high to low
transition. Data transfer is conducted serially in multiple units of 1 byte (8 bits). The former 4 bits are used to
specify in the Address Pointer a head address with which data transfer is to be commenced from the host. The
latter 4 bits are used to select either reading data transfer or writing data transfer, and to set the Transfer Format
Register to specify an appropriate data transfer format. All data transfer formats are designed to transfer the
most significant bit (MSB) first.
CE
1
2
3
4
5
6
7
8
1
2
A3
A2
A1
A0
C3
C2
C1
C0
D7
D6
3
SCLK
SIO
Setting
the Address Pointer
Setting the Transfer
Format Register
D3
D2
D1
D0
Writing or Reading data transfer
Two types of data transfer formats are available for reading data transfer and writing data transfer each.
•
Writing Data Transfer Formats
(1) 1-byte Writing Data Transfer Format
The first type of writing data transfer format is designed to transfer 1-byte data at a time and can be selected by
specifying in the address pointer a head address with which writing data transfer is to be commenced and then
writing the setting of 8h to the transfer format register. This 1-byte writing data transfer can be completed by
driving the CE pin low or continued by specifying a new head address in the address pointer and setting the data
transfer format.
Example of 1-byte Writing Data Transfer (For Writing Data to Addresses Fh and 7h)
CE
SIO
1 1 1 1 1 0 0 0
Specifying FhSetting 8h in
in the
Address
Pointer
the Transfer
Data
Writing data to
address Fh
Format
Register
Data
Specifying 7h Setting 8h in Writing data to
in the
Address
Data transfer from the host
26
0 1 1 1 1 0 0 0
Pointer
the Transfer
address 7h
Format
Register
Data transfer from the RTCs
R2062 series
(2) Burst Writing Data Transfer Format
The second type of writing data transfer format is designed to transfer a sequence of data serially and can be
selected by specifying in the address pointer a head address with which writing data transfer is to be
commenced and then writing the setting of 0h to the transfer format register. The address pointer is
incremented for each transfer of 1-byte data and cycled from Fh to 0h. This burst writing data transfer can be
completed by driving the CE pin low.
Example of Burst Writing Data Transfer (For Writing Data to Addresses Eh, Fh, and 0h)
CE
SIO
1 1 1 0 0 0 0 0
Data
Specifying EhSetting 0h in Writing data to
in the
Address
Pointer
the Transfer
Writing data to
address Fh
address Eh
Writing data to
address 0h
Format
Register
Data transfer from the host
•
Data
Data
Data transfer from the RTCs
Reading Data Transfer Formats
(1) 1-byte Reading Data Transfer Format
The first type of reading data transfer format is designed to transfer 1-byte data at a time and can be selected by
specifying in the Address Pointer a head address with which reading data transfer is to be commenced and then
the setting of writing Ch to the Transfer Format Register. This 1-byte reading data transfer can be completed by
driving the CE pin low or continued by specifying a new head address in the Address Pointer and selecting this
type of reading data Transfer Format.
Example of 1-byte Reading Data Transfer (For Reading Data from Addresses Eh and 2h)
CE
SIO
1 1 1 0 1 1 0 0
Data
Specifying EhSetting Ch in
Reading data from
in the
Address
Pointer
the Transfer
address Eh
Format
0 0 1 0 1 1 0 0
Specifying 2h Setting Ch in Reading data from
in the
Address
Register
Data transfer from the host
Data
Pointer
the Transfer
address 2h
Format
Register
Data transfer from the RTCs
27
R2062 series
(2) Burst Reading Data Transfer Format
The second type of reading data transfer format is designed to transfer a sequence of data serially and can be
selected by specifying in the address pointer a head address with which reading data transfer is to be
commenced and then writing the setting of 4h to the transfer format register. The address pointer is
incremented for each transfer of 1-byte data and cycled from Fh to 0h. This burst reading data transfer can be
completed by driving the CE pin low.
Example of Burst Reading Data Transfer (For Reading Data from Addresses Fh, 0h, and 1h)
CE
SIO
1 1 1 1 0 1 0 0
DATA
Specifying FhSetting 4h in Reading data from
the Transfer
in the
address Fh
Address
Pointer
DATA
DATA
Reading data from
Reading data from
address 0h
address 1h
Format
Register
Data transfer from the host
Data transfer from the RTCs
(3) Combination of 1-byte Reading and writing Data Transfer Formats
The 1-byte reading and writing data transfer formats can be combined together and further followed by any other
data transfer format.
Example of Reading Modify Writing Data Transfer
(For Reading and Writing Data from and to Address Fh)
CE
SIO
1 1 1 1 1 1 0 0
DATA
Specifying FhSetting Ch in Reading data from
the Transfer
in the
address Fh
Format
Address
Pointer
DATA
1 1 1 1 1 0 0 0
Specifying FhSetting 8h in
in the
Address
Register
Pointer
Data transfer from the host
Writing data to
the Transfer
address Fh
Format
Register
Data transfer from the RTCs
The reading and writing data transfer formats correspond to the settings in the transfer format register as shown
in the table below.
Writing data
transfer
Reading data
transfer
28
1 Byte
8h
(1,0,0,0)
Ch
(1,1,0,0)
Burst
0h
(0,0,0,0)
4h
(0,1,0,0)
R2062 series
•
Considerations in Reading and Writing Time Data under special condition
Any carry to the second digits in the process of reading or writing time data may cause reading or writing
erroneous time data. For example, suppose a carry out of 13:59:59 into 14:00:00 occurs in the process of
reading time data in the middle of shifting from the minute digits to the hour digits. At this moment, the second
digits, the minute digits, and the hour digits read 59 seconds, 59 minutes, and 14 hours, respectively (indicating
14:59:59) to cause the reading of time data deviating from actual time virtually 1 hour. A similar error also
occurs in writing time data. To prevent such errors in reading and writing time data, the R2062 has the function
of temporarily locking any carry to the second digits during the high interval of the CE pin and unlocking such a
carry in its high to low transition. Note that a carry to the second digits can be locked for only 1 second, during
which time the CE pin should be driven low.
Actual time
13:59:59
14:00:00
14:00:01
CE
Max.62µs
Time counts
within RTC
13:59:59
14:00:00
14:00:01
The effective use of this function requires the following considerations in reading and writing time data:
(1) Hold the CE pin high in each session of reading or writing time data.
(2) Ensure that the high interval of the CE pin lasts within 1 second. Should there be any possibility of the host
going down in the process of reading or writing time data, make arrangements in the peripheral circuitry as to
drive the CE pin low or open at the moment that the host actually goes down.
(3) Leave a time span of 31µs or more from the low to high transition of the CE pin to the start of access to
addresses 0h to 6h in order that any ongoing carry of the time digits may be completed within this time span.
(4) Leave a time span of 62µs or more from the high to low transition of the CE pin to its low to high transition in
order that any ongoing carry of the time digits during the high interval of the CE pin may be adjusted within this
time span.
The considerations listed in (1), (3), and (4) above are not required when the process of reading or writing time
data is obviously free from any carry of the time digits.
(e.g. reading or writing time data in synchronization with the periodic interrupt function in the level mode or the
alarm interrupt function).
Good and bad examples of reading and writing time data are illustrated on the next page.
29
R2062 series
Good Example
Any address other than addresses 0h to 6h
permits of immediate reading or writing without
requiring a time span of 31 µs.
Time span of 31µs or more
CE
SIO
F4h
Address Pointer
= Fh
Transfer Format
Register = 4h
DATA
DATA
Reading from
Address Fh
(control2)
Reading from
Address 0h
(sec.)
DATA
DATA
Reading from
Address 1h
(min.)
Reading from
Address 2h
(hr.)
Bad Example (1)
(Where the CE pin is once driven low in the process of reading time data)
31µs or more
31µs or more
CE
SIO
0Ch
Address Pointer
= 0h
Transfer Format
Register = Ch
Data
14h
Address Pointer
= 1h
Transfer Format
Register = 4h
Reading from
Address 0h
(sec.)
Data
Data
Reading from
Address 1h
(min.)
Reading from
Address 2h
(hr.)
Bad Example (2)
(Where a time span of less than 31µs is left until the start of the process of writing time data)
Time span of less than 31µs
CE
F0h
SIO
Address Pointer
= Fh
Transfer Format
Register = 0h
Data
Writing to
Address Fh
(contorl2)
Data
Writing to
Address 0h
(sec.)
Data
Writing to
Address 1h
(min.)
Data
Writing to
Address 2h
(hr.)
Bad Example (3)
(Where a time span of less than 62µs is left between the adjacent processes of reading time data)
Less than 62µs
CE
0Ch
SIO
Address Pointer
= 0h
Transfer Format
Register = Ch
0Ch
30
0Ch
Data
Reading from
Address 0h
(sec.)
Data transfer from the host
Address Pointer
= 0h
Transfer Format
Register = Ch
Data
Data
Reading from
Address 0h
(sec.)
Data transfer from RTCs
R2062 series
Configuration of Oscillation Circuit and Correction of Time Count
Deviations
•
Configuration of Oscillation Circuit
OSCIN
Oscillator CG
Circuit
32kHz
OSCOUT
Typical externally-equipped element
X’tal : 32.768kHz
(R1=30kΩ typ)
(CL=6pF to 8pF)
Standard values of internal elements
CG,CD 10pF typ
CD
A
The oscillation circuit is driven at a constant voltage of approximately 1.2 volts relative to the level of the VSS pin
input. As such, it is configured to generate an oscillating waveform with a peak-to-peak voltage on the order of
1.1 volts on the positive side of the VSS pin input.
< Considerations in Handling Quartz Crystal Units >
Generally, quartz crystal units have basic characteristics including an equivalent series resistance (R1) indicating
the ease of their oscillation and a load capacitance (CL) indicating the degree of their center frequency.
Particularly, quartz crystal units intended for use in the R2062 are recommended to have a typical R1 value of
30kΩ and a typical CL value of 6 to 8pF. To confirm these recommended values, contact the manufacturers of
quartz crystal units intended for use in these particular models.
< Considerations in Installing Components around the Oscillation Circuit >
1) Install the quartz crystal unit in the closest possible vicinity to the real-time clock ICs.
2) Avoid laying any signal lines or power lines in the vicinity of the oscillation circuit (particularly in the area
marked "A" in the above figure).
3) Apply the highest possible insulation resistance between the OSCIN and OSCOUT pins and the printed
circuit board.
4) Avoid using any long parallel lines to wire the OSCIN and OSCOUT pins.
5) Take extreme care not to cause condensation, which leads to various problems such as oscillation halt.
< Other Relevant Considerations >
1) We cannot recommend connecting the external input of 32.768-kHz clock pulses to the OSCIN pin.
2) To maintain stable characteristics of the quartz crystal unit, avoid driving any other IC through 32.768-kHz
clock pulses output from the OSCOUT pin.
31
R2062 series
•
Measurement of Oscillation Frequency
VCC
OSCIN
32768Hz
OSCOUT
Frequency
Counter
CLKOUT
VDD
VSS
* 1) The R2062 is configured to generate 32.768-kHz clock pulses for output from the CLKOUT pin.
* 2) A frequency counter with 6 (more preferably 7) or more digits on the order of 1ppm is recommended for
use in the measurement of the oscillation frequency of the oscillation circuit.
•
Adjustment of Oscillation frequency
The oscillation frequency of the oscillation circuit can be adjusted by varying procedures depending on the
usage of Model R2062 in the system into which they are to be built and on the allowable degree of time count
errors. The flow chart below serves as a guide to selecting an optimum oscillation frequency adjustment
procedure for the relevant system.
Start
Use 32-kHz
clock output?
YES
NO Allowable time count precision on order of oscillation
frequency variations of crystal oscillator (*1) plus NO
frequency variations of RTC (*2)? (*3)
YES
YES
Course (A)
Course (B)
Use 32-kHz clock output without regard
to its frequency precision
Course (C)
NO
YES
Allowable time count precision on order of oscillation
frequency variations of crystal oscillator (*1) plus NO
frequency variations of RTC (*2)? (*3)
Course (D)
* 1) Generally, quartz crystal units for commercial use are classified in terms of their center frequency
depending on their load capacitance (CL) and further divided into ranks on the order of ±10, ±20, and ±50ppm
depending on the degree of their oscillation frequency variations.
32
R2062 series
* 2) Basically, Model R2062 is configured to cause frequency variations on the order of ±5 to ±10ppm at 25°C.
* 3) Time count precision as referred to in the above flow chart is applicable to normal temperature and actually
affected by the temperature characteristics and other properties of quartz crystal units.
Course (A)
When the time count precision of each RTC is not to be adjusted, the quartz crystal unit intended for use in that
RTC may have any CL value requiring no presetting. The quartz crystal unit may be subject to frequency
variations which are selectable within the allowable range of time count precision. Several quartz crystal units
and RTCs should be used to find the center frequency of the quartz crystal units by the method described in
"P32 • Measurement of Oscillation Frequency" and then calculate an appropriate oscillation adjustment value
by the method described in "P34 • Oscillation Adjustment Circuit" for writing this value to the R2062.
Course (B)
When the time count precision of each RTC is to be adjusted within the oscillation frequency variations of the
quartz crystal unit plus the frequency variations of the real-time clock ICs, it becomes necessary to correct
deviations in the time count of each RTC by the method described in " P34 • Oscillation Adjustment Circuit".
Such oscillation adjustment provides quartz crystal units with a wider range of allowable settings of their
oscillation frequency variations and their CL values. The real-time clock IC and the quartz crystal unit intended
for use in that real-time clock IC should be used to find the center frequency of the quartz crystal unit by the
method described in " P32 • Measurement of Oscillation Frequency" and then confirm the center frequency
thus found to fall within the range adjustable by the oscillation adjustment circuit before adjusting the oscillation
frequency of the oscillation circuit. At normal temperature, the oscillation frequency of the oscillator circuit can
be adjusted by up to approximately ±0.5ppm.
Course (C)
Course (C) together with Course (D) requires adjusting the time count precision of each RTC as well as the
frequency of 32.768-kHz clock pulses output from the CLKOUT pin. Normally, the oscillation frequency of the
quartz crystal unit intended for use in the RTCs should be adjusted by adjusting the oscillation stabilizing
capacitors CG and CD connected to both ends of the quartz crystal unit. The R2062, which incorporate the CG
and the CD, require adjusting the oscillation frequency of the quartz crystal unit through its CL value.
Generally, the relationship between the CL value and the CG and CD values can be represented by the following
equation:
CL = (CG × CD)/(CG + CD) + CS where "CS" represents the floating capacity of the printed circuit board.
The quartz crystal unit intended for use in the R2062 is recommended to have the CL value on the order of 6 to
8pF. Its oscillation frequency should be measured by the method described in " P32 • Measurement of
Oscillation Frequency". Any quartz crystal unit found to have an excessively high or low oscillation frequency
(causing a time count gain or loss, respectively) should be replaced with another one having a smaller and
greater CL value, respectively until another one having an optimum CL value is selected. In this case, the bit
settings disabling the oscillation adjustment circuit (see " P34 • Oscillation Adjustment Circuit ") should be
written to the oscillation adjustment register.
Incidentally, the high oscillation frequency of the quartz crystal unit can also be adjusted by adding an external
oscillation stabilization capacitor CGout as illustrated in the diagram below.
33
R2062 series
*1) The CGout should have a capacitance ranging
from 0 to 15 pF.
OSCIN
Oscillator
Circuit
CG
RD
32kHz
OSCOUT
CD
CGout
*1)
Course (D)
It is necessary to select the quartz crystal unit in the same manner as in Course (C) as well as correct errors in
the time count of each RTC in the same manner as in Course (B) by the method described in " P34 •
Oscillation Adjustment Circuit ".
•
Oscillation Adjustment Circuit
The oscillation adjustment circuit can be used to correct a time count gain or loss with high precision by varying
the number of 1-second clock pulses once per 20 seconds or 60 seconds. When DEV bit in the Oscillation
Adjustment Register is set to 0, R2062 varies number of 1-second clock pulses once per 20 seconds. When
DEV bit is set to 1, R2062 varies number of 1-second clock pulses once per 60 seconds. The oscillation
adjustment circuit can be disabled by writing the settings of "*, 0, 0, 0, 0, 0, *" ("*" representing "0" or "1") to the
F6, F5, F4, F3, F2, F1, and F0 bits in the oscillation adjustment circuit. Conversely, when such oscillation
adjustment is to be made, an appropriate oscillation adjustment value can be calculated by the equation below
for writing to the oscillation adjustment circuit.
(1) When Oscillation Frequency (* 1) Is Higher Than Target Frequency (* 2) (Causing Time Count Gain)
When DEV=0:
Oscillation adjustment value (*3) = (Oscillation frequency - Target Frequency + 0.1)
Oscillation frequency × 3.051 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 10 + 1
When DEV=1:
Oscillation adjustment value (*3) = (Oscillation frequency - Target Frequency + 0.0333)
Oscillation frequency × 1.017 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 30 + 1
* 1) Oscillation frequency:
32768 times the frequency of 1Hz clock pulse output from the INTR pin at normal temperature in the
manner described in " P32 • Measurement of Oscillation Frequency".
* 2) Target frequency:
Desired frequency to be set. Generally, a 32.768-kHz quartz crystal unit has such temperature
characteristics as to have the highest oscillation frequency at normal temperature. Consequently,
the quartz crystal unit is recommended to have target frequency settings on the order of 32.768 to
32.76810 kHz (+3.05ppm relative to 32.768 kHz). Note that the target frequency differs depending
on the environment or location where the equipment incorporating the RTC is expected to be
operated.
* 3) Oscillation adjustment value:
Value that is to be finally written to the F0 to F6 bits in the Oscillation Adjustment Register and is
represented in 7-bit coded decimal notation.
34
R2062 series
(2) When Oscillation Frequency Is Equal To Target Frequency (Causing Time Count neither Gain nor Loss)
Oscillation adjustment value = 0, +1, -64, or –63
(3) When Oscillation Frequency Is Lower Than Target Frequency (Causing Time Count Loss)
When DEV=0:
Oscillation adjustment value = (Oscillation frequency - Target Frequency)
Oscillation frequency × 3.051 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 10
When DEV=1:
Oscillation adjustment value = (Oscillation frequency - Target Frequency)
Oscillation frequency × 1.017 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 30
Oscillation adjustment value calculations are exemplified below
(A) For an oscillation frequency = 32768.85Hz and a target frequency = 32768.05Hz
When setting DEV bit to 0:
Oscillation adjustment value = (32768.85 - 32768.05 + 0.1) / (32768.85 × 3.051 × 10-6)
≈ (32768.85 - 32768.05) × 10 + 1
= 9.001 ≈ 9
In this instance, write the settings (DEV,F6,F5,F4,F3,F2,F1,F0)=(0,0,0,0,1,0,0,1) in the oscillation adjustment
register. Thus, an appropriate oscillation adjustment value in the presence of any time count gain represents a
distance from 01h.
When setting DEV bit to 1:
Oscillation adjustment value = (32768.85 - 32768.05 + 0.0333) / (32768.85 × 1.017 × 10-6)
≈ (32768.85 - 32768.05) × 30 + 1
= 25.00 ≈ 25
In this instance, write the settings (DEV,F6,F5,F4,F3,F2,F1,F0)=(1,0,0,1,1,0,0,1) in the oscillation adjustment
register.
(B) For an oscillation frequency = 32762.22Hz and a target frequency = 32768.05Hz
When setting DEV bit to 0:
Oscillation adjustment value = (32762.22 - 32768.05) / (32762.22 × 3.051 × 10-6)
≈ (32762.22 - 32768.05) × 10
= -58.325 ≈ -58
To represent an oscillation adjustment value of - 58 in 7-bit coded decimal notation, subtract 58 (3Ah) from 128
(80h) to obtain 46h. In this instance, write the settings of (DEV,F6,F5,F4,F3,F2,F1,F0) = (0,1,0,0,0,1,1,0) in the
oscillation adjustment register. Thus, an appropriate oscillation adjustment value in the presence of any time
count loss represents a distance from 80h.
When setting DEV bit to 1:
Oscillation adjustment value = (32762.22 - 32768.05) / (32762.22 × 1.017 × 10-6)
≈ (32762.22 - 32768.05) × 30
= -174.97 ≈ -175
35
R2062 series
Oscillation adjustment value can be set from -62 to 63. Then, in this case, Oscillation adjustment value is out of
range.
(4) Difference between DEV=0 and DEV=1
Difference between DEV=0 and DEV=1 is following,
Maximum value range
Minimum resolution
DEV=0
-189.2ppm to 189.2ppm
3ppm
DEV=1
-62ppm to 63ppm
1ppm
Notes:
If following 3 conditions are completed, actual clock adjustment value could be different from target
adjustment value that set by oscillator adjustment function.
1. Using oscillator adjustment function
2. Access to R2062 at random, or synchronized with external clock that has no relation to R2062, or
synchronized with periodic interrupt in pulse mode.
3. Access to R2062 more than 2 times per each second on average.
For more details, please contact to Ricoh.
•
How to evaluate the clock gain or loss
The oscillator adjustment circuit is configured to change time counts of 1 second on the basis of the settings of
the oscillation adjustment register once in 20 seconds or 60 seconds. The way to measure the clock error as
follows:
(1) Output a 1Hz clock pulse of Pulse Mode with interrupt pin
Set (0,0,x,x,0,0,1,1) to Control Register 1 at address Eh.
(2) After setting the oscillation adjustment register, 1Hz clock period changes every 20seconds ( or every 60
seconds) like next page figure.
1Hz clock pulse
T0
T0
T0
19 times
T1
1 time
Measure the interval of T0 and T1 with frequency counter. A frequency counter with 7 or more digits is
recommended for the measurement.
(3) Calculate the typical period from T0 and T1
T = (19×T0+1×T1)/20
Calculate the time error from T.
36
R2062 series
Power-on Reset, Oscillation Halt Sensing, and Supply Voltage
Monitoring
•
PON, XST , and VDET
The power-on reset circuit is configured to reset control register1, 2, and clock adjustment register when VDD
power up from 0v. The oscillation halt sensing circuit is configured to record a halt on oscillation by 32.768-kHz
clock pulses. The supply voltage monitoring circuit is configured to record a drop in supply voltage below a
threshold voltage of 2.1 or 1.35v.
Each function has a monitor bit. I.e. the PON bit is for the power-on reset circuit, and XST bit is for the
oscillation halt sensing circuit, and VDET is for the supply voltage monitoring circuit. PON and VDET bits are
activated to “H”. However, XST bit is activated to “L”. The PON and VDET accept only the writing of 0, but
XST accepts the writing of 0 and 1. The PON bit is set to 1, when VDD power-up from 0V, but VDET is set to
0, and XST is indefinite.
The functions of these three monitor bits are shown in the table below.
D4 in Address Fh
High
1
XST
Monitoring for the
oscillation halt sensing
function
D5 in Address Fh
Low
indefinite
VDET
a drop in supply voltage
below a threshold voltage
of 2.1 or 1.35v
D6 in Address Fh
High
0
0 only
Both 0 and 1
0 only
PON
Monitoring for the
power-on reset function
Function
Address
Activated
When VDD power
up from 0v
accept the writing
The relationship between the PON, XST , and VDET is shown in the table below.
PON
XST
VDET
0
0
0
0
0
1
0
1
0
0
1
1
1
*
*
Conditions of supply voltage
and oscillation
Halt on oscillation, but no drop in
VDD supply voltage below
threshold voltage
Halt on oscillation and drop in VDD
supply voltage below threshold
voltage, but no drop to 0V
No drop in VDD supply voltage
below threshold voltage and no
halt in oscillation
Drop in VDD supply voltage below
threshold voltage and no halt on
oscillation
Drop in supply voltage to 0v
Condition of oscillator, and
back-up status
Halt on oscillation cause of
condensation etc.
Halt on oscillation cause of drop in
back-up battery voltage
Normal condition
No halt on oscillation, but drop in
back-up battery voltage
Power-up from 0v,
37
R2062 series
Threshold voltage (2.1V or 1.35V)
VDD
32768Hz Oscillation
Power-on reset flag
(PON)
Oscillation halt
sensing flag ( XST )
VDD supply voltage
monitor flag (VDET)
Internal initialization
period (1 to 2 sec.)
VDET←0
XST ←1
PON←0
VDET←0
XST ←1
PON←1
Internal initialization
period (1 to 2 sec.)
VDET←0
XST ←1
PON←0
When the PON bit is set to 1 in the control register 2, the DEV, F6 to F0, WALE, DALE, 12 /24, SCRATCH2,
TEST, CT2, CT1, CT0, VDSL, VDET, SCRATCH1, CTFG, WAFG, and DAFG bits are reset to 0 in the oscillation
adjustment register, the control register 1, and the control register 2. The PON bit is also set to 1 at power-on
from 0 volts.
< Considerations in Using Oscillation Halt Sensing Circuit >
Be sure to prevent the oscillation halt sensing circuit from malfunctioning by preventing the following:
1) Instantaneous power-down on the VDD
2) Condensation on the quartz crystal unit
3) On-board noise to the quartz crystal unit
4) Applying to individual pins voltage exceeding their respective maximum ratings
In particular, note that the XST bit may fail to be set to 0 in the presence of any applied supply voltage as
illustrated below in such events as backup battery installation. Further, give special considerations to prevent
excessive chattering in the oscillation halt sensing circuit.
VDD
38
R2062 series
•
Voltage Monitoring Circuit
R2062 incorporates two kinds of voltage monitoring function. These are shown in the table below.
VCC Voltage Monitoring
VCC Voltage Monitoring
Circuit
Circuit (VDET)
Purpose
CPU reset output
Back-up battery checker
Monitoring supply voltage
VCC pin
VDD pin (supply voltage for the
internal RTC circuit)
Output for result
Store in the Control Register 2
VDCC pin
(D6 in Address Fh)
Function
After falling VCC, VDCC outputs
“L”. tDEALY after rising VCC,
VDCC outputs “H” (OFF)
Below the threshold voltage, SW1
turns off on. Over the threshold
voltage, SW1 turns on.
Detector Threshold (falling
-VDET1
Selecting from VDETH or VDETL by
edge of power supply voltage)
writing to the register
(D7 in Address Fh)
Detector Released
+VDET1
Same as falling edge
Voltage (rising edge of power
( No hysteresis)
supply voltage)
The way to monitor
Always
One time every second
The VDD supply voltage monitoring circuit is configured to conduct a sampling operation during an interval of
7.8ms per second to check for a drop in supply voltage below a threshold voltage of 2.1 or 1.35v for the VDSL bit
setting of 0 (the default setting) or 1, respectively, in the Control Register 2, thus minimizing supply current
requirements as illustrated in the timing chart below. This circuit suspends a sampling operation once the
VDET bit is set to 1 in the Control Register 2. The VDD supply voltage monitor is useful for back-up battery
checking.
VDD
2.1v or 1.35v
PON
Sampling timing for VDD
supply voltage monitor
7.8ms
Internal
initialization
period
(1 to 2sec.)
1s
VDET
(D6 in Address Fh)
PON←0
VDET←0
VDET←0
39
R2062 series
The VCC supply voltage monitor circuit operates always. When VCC rising over +VDET1, SW1 turns on. And
tDELAY after rising VCC, VDCC outputs OFF(H). But when oscillation is halt, VCC outputs OFF(H) tDELAY after
oscillation starting. When VCC falling beyond -VDET1, SW1 turns off. And VDCC outputs “L”.
Oscillation starting
-VDET1
+VDET1
Same voltage level as VSB
VCC
VDD
32768Hz Oscillation
VDCC
tDELAY
tDELAY
OFF
SW1
ON
tDELAY
OFF
ON
ON
Battery Switch Over Circuit
R2062 incorporates two power supply pins, VDD and VCC. VDD pin is the power supply pin for internal real
time clock circuit. When VCC voltage is lower than ±VDET1, VDD supplies the power to R2062, and when higher
than ±VDET1, VCC supplies the power to VDD. The timing chart for VCC and VDD is shown following.
+VDET1
-VDET1
VCC
VDD
(1)
(2)
(3)
(2)
(3)
(1) When VDD and VCC is rising from 0V, VDD follows half of VCC voltage level. After VCC rising over
+VDET1, VDD follows VCC voltage level.
(2) When VCC is higher than +VDET1, VDD level is equal to VCC.
(3) After VCC falling beyond –VDET1, VDD level is determined by the rechargeable battery voltage connected to
VDD.
40
R2062 series
Alarm and Periodic Interrupt
The R2062 incorporates the alarm interrupt circuit and the periodic interrupt circuit that are configured to
generate alarm signals and periodic interrupt signals for output from the INTR pin as described below.
(1) Alarm Interrupt Circuit
The alarm interrupt circuit is configured to generate alarm signals for output from the INTR , which is driven low
(enabled) upon the occurrence of a match between current time read by the time counters (the day-of-week,
hour, and minute counters) and alarm time preset by the alarm registers (the Alarm_W registers intended for the
day-of-week, hour, and minute digit settings and the Alarm_D registers intended for the hour and minute digit
settings).
(2) Periodic Interrupt Circuit
The periodic interrupt circuit is configured to generate either clock pulses in the pulse mode or interrupt signals in
the level mode for output from the INTR pin depending on the CT2, CT1, and CT0 bit settings in the control
register 1.
The above two types of interrupt signals are monitored by the flag bits (i.e. the WAFG, DAFG, and CTFG bits in
the Control Register 2) and enabled or disabled by the enable bits (i.e. the WALE, DALE, CT2, CT1, and CT0
bits in the Control Register 1) as listed in the table below.
Alarm_W
Alarm_D
Peridic interrupt
Flag bits
WAFG
(D1 at Address Fh)
DAFG
(D0 at Address Fh)
CTFG
(D2 at Address Fh)
Enable bits
WALE
(D7 at Address Eh)
DALE
(D6 at Address Eh)
CT2=CT1=CT0=0
(These bit setting of “0” disable the Periodic Interrupt)
(D2 to D0 at Address Eh)
* At power-on, when the WALE, DALE, CT2, CT1, and CT0 bits are set to 0 in the Control Register 1,
the INTR pin is driven high (disabled).
* When two types of interrupt signals are output simultaneously from the INTR pin, the output from the
INTR pin becomes an OR waveform of their negative logic.
Example: Combined Output to INTR Pin Under Control of
Alarm_D and Periodic Interrupt
Alarm_D
Periodic Interrupt
IN T R
In this event, which type of interrupt signal is output from the INTR pin can be confirmed by reading the
DAFG, and CTFG bit settings in the Control Register 2.
41
R2062 series
•
Alarm Interrupt
The alarm interrupt circuit is controlled by the enable bits (i.e. the WALE and DALE bits in the Control Register 1)
and the flag bits (i.e. the WAFG and DAFG bits in the Control Register 2). The enable bits can be used to
enable this circuit when set to 1 and to disable it when set to 0. When intended for reading, the flag bits can be
used to monitor alarm interrupt signals. When intended for writing, the flag bits will cause no event when set to
1 and will drive high (disable) the alarm interrupt circuit when set to 0.
The enable bits will not be affected even when the flag bits are set to 0. In this event, therefore, the alarm
interrupt circuit will continue to function until it is driven low (enabled) upon the next occurrence of a match
between current time and preset alarm time.
The alarm function can be set by presetting desired alarm time in the alarm registers (the Alarm_W Registers for
the day-of-week digit settings and both the Alarm_W Registers and the Alarm_D Registers for the hour and
minute digit settings) with the WALE and DALE bits once set to 0 and then to 1 in the Control Register 1. Note
that the WALE and DALE bits should be once set to 0 in order to disable the alarm interrupt circuit upon the
coincidental occurrence of a match between current time and preset alarm time in the process of setting the
alarm function.
Interval (1min.) during which a match
between current time and preset alarm time
occurs
IN T R
WALE←1 current time =
WALE←0
preset alarm time (DALE)
(DALE)
WALE←1
(DALE)
current time =
preset alarm time
IN T R
WALE←1 current time =
preset alarm time
(DALE)
WAFG←0
(DAFG)
current time =
preset alarm time
After setting WALE(DALW) to 0, Alarm registers is set to current time, and WALE(DALE) is set to 1, INTR will
be not driven to “L” immediately, INTR will be driven to “L” at next alarm setting time.
42
R2062 series
•
Periodic Interrupt
Setting of the periodic selection bits (CT2 to CT0) enables periodic interrupt to the CPU. There are two waveform
modes: pulse mode and level mode. In the pulse mode, the output has a waveform duty cycle of around 50%.
In the level mode, the output is cyclically driven low and, when the CTFG bit is set to 0, the output is return to
High (OFF).
CT2
CT1
Description
Interrupt Cycle and Falling Timing
CT0
Wave form
mode
0
0
0
0
1
0
0
1
1
0
0
1
0
1
0
Pulse Mode *1)
Pulse Mode *1)
Level Mode *2)
1
0
1
Level Mode *2)
1
1
0
Level Mode *2)
1
1
1
Level Mode *2)
OFF(H)
Fixed at “L”
2Hz(Duty50%)
1Hz(Duty50%)
Once per 1 second (Synchronized with
Second counter increment)
Once per 1 minute (at 00 seconds of every
Minute)
Once per hour (at 00 minutes and 00
Seconds of every hour)
Once per month (at 00 hours, 00 minutes,
and 00 seconds of first day of every month)
(Default)
*1) Pulse Mode:
2-Hz and 1-Hz clock pulses are output in synchronization with the increment of the second counter as
illustrated in the timing chart below.
CTFG Bit
IN TR
Pin
Approx. 92µs
(Increment of second counter)
Rewriting of the second counter
In the pulse mode, the increment of the second counter is delayed by approximately 92 µs from the falling
edge of clock pulses. Consequently, time readings immediately after the falling edge of clock pulses may
appear to lag behind the time counts of the real-time clocks by approximately 1 second. Rewriting the
second counter will reset the other time counters of less than 1 second, driving the INTR pin low.
*2) Level Mode:
Periodic interrupt signals are output with selectable interrupt cycle settings of 1 second, 1 minute, 1 hour,
and 1 month. The increment of the second counter is synchronized with the falling edge of periodic
interrupt signals. For example, periodic interrupt signals with an interrupt cycle setting of 1 second are
output in synchronization with the increment of the second counter as illustrated in the timing chart below.
43
R2062 series
CTFG Bit
IN TR
Pin
Setting CTFG bit to 0
(Increment of
second counter)
(Increment of
second counter)
Setting CTFG bit to 0
(Increment of
second counter)
*1), *2) When the oscillation adjustment circuit is used, the interrupt cycle will fluctuate once per 20sec. as
follows:
Pulse Mode: The “L” period of output pulses will increment or decrement by a maximum of ±3.784ms. For
example, 1-Hz clock pulses will have a duty cycle of 50 ±0.3784%.
Level Mode: A periodic interrupt cycle of 1 second will increment or decrement by a maximum of ±3.784ms.
44
R2062 series
Typical Applications
•
Typical Power Circuit Configurations
The case of back-up by
capacitor or secondary battery
(Charging voltage is equal to CPU
power supply voltage)
The case of back-up by
primary battery
CPU power
supply
VCC
VCC
CPU Power
Supply
VDD
VDD
0.1µF
0.1µF
CR2025
etc.
ML614
etc.
VSS
VSS
VDD pin cannot be connected to any additional heavy load components such as SRAM. And VDD pin must be
connected C2, and C2 should be over 0.1µF.
CPU power supply
R2062 Series
R1
C2
VDD
Vbat
VCC
SW1
C3
VOLTAGE
DETECTOR
-VDET1
CPU
Rcpu
When secondary battery or double layer capacitor connects to VDD pin, after CPU power supply turning off,
secondary battery discharges through the root above figure. If R1 is much smaller than CPU impedance
(Rcpu), VCC voltage keeps higher than -VDET1, and SW1 keeps on. Therefore R1 must be specified by
following formula.
R1 > Rcpu x (Vbat - (-VDET1)) / (-VDET1)
R1 is specified by back-up battery or double layer capacitor, too. Please check the data sheet for back-up
devices.
45
R2062 series
•
Connection of CIN pin
Please connect capacitor over 0.1µF between CIN and VSS pin.
•
Connection of INTR and VDCC Pin
The INTR and VDCC pins follow the N-channel open drain output logic and contains no protective diode on
the power supply side. As such, it can be connected to a pull-up resistor of up to 5.5 volts regardless of supply
voltage.
CPU power supply
A
INTR or VDCC
*1)
B
OSCIN
OSCOUT
VDD
VSS
46
Backup power supply
32768Hz
*1) Depending on whether the INTR and
VDCC pins are to be used during
battery backup, it should be connected
to a pull-up resistor at the following
different positions:
(1) Position A in the left diagram when it is
not to be used during battery backup.
(2) Position B in the left diagram when it is to
be used during battery backup.
R2062 series
Typical Characteristics
•
Time keeping current (IDD) vs. Supply voltage (VDD)
(Topt=25°C)
Test Circuit
VCC
Time keeping current (uA)
0.5
0.4
INTR
0.3
OSCIN
OSCOUT
CLKOUT
VDCC
0.2
CE
VDD
0.1
SCLK
CIN
SIO
VSS
A
0.1µF
0.1µF
0
0
•
1
2
3
VDD(v)
4
5
6
Stand-by current (ICC) vs. Supply voltage (VCC)
(Topt=25°C)
Test circuit
VCC
Stand-by current (uA)
4
A
3
INTR
OSCIN
OSCOUT
CLKOUT
2
VDCC
CE
VDD
1
0.1µF
SCLK
CIN
SIO
VSS
0.1µF
0
0
•
1
2
3
VCC(v)
4
5
6
Time keeping current (IDD) vs. Operating Temperature (Topt)
(VDD=3V)
Test circuit
VCC
Time keeping current (uA)
0.7
OSCIN
0.6
INTR
0.5
0.4
CLKOUT
OSCOUT
VDCC
0.3
CE
0.2
0.1
VDD
SCLK
CIN
SIO
VSS
A
0.1µF
0.1µF
0
-50
-25
0
25
50
75
Operating Temperature (Celsius)
100
47
R2062 series
•
Stand-by current (ICC) vs. Operating Temperature (Topt)
(VCC=3V)
Test circuit
Stand-by Current (uA)
4
VCC
3
A
INTR
OSCOUT
2
CLKOUT
VDCC
1
CE
VDD
0.1µF
0
-50
-25
0
25
50
75
100
Operating Temperature (Celsius)
•
OSCIN
SCLK
CIN
SIO
VSS
0.1µF
CPU access current vs. SCLK clock frequency (kHz)
(Topt=25°C)
CPU access current (uA)
80
VCC=5v
60
40
VCC=3v
20
0
0
200
400
600
800
1000
SCL clock frequency (KHz)
•
Oscillation frequency deviation (∆f/f0) vs. Operating temperature (Topt)
(VCC=3V Topt=25°C as standard)
Test circuit
Oscillation frequency deviation
df/f0(ppm)
20
0
-20
-40
-60
-80
-100
-120
-140
-160
VCC
INTR
Frequency
counter
CE
OSCOUT
VDCC
VDD
0.1µF
-50
-25
0
25
50
75
SCLK
CIN
SIO
VSS
100
Operating temperature Topt(Celsius)
48
CLKOUT
OSCIN
0.1µF
R2062 series
•
Frequency deviation (∆f/f0) vs. Supply voltage (VCC/VDD)
Frequency deviation df/f0(ppm)
(Topt=25°C) VCC/VDD=3V as standard
Test circuit
2
VCC
INTR
0
-1
Frequency
counter
-2
CLKOUT
VDCC
VDD
0.1µF
-4
1
2
3
4
5
SCLK
CIN
SIO
VSS
6
VCC/VSB(v)
0.1µF
Frequency deviation (∆f/f0) vs. CGOUT
Frequency deviation df/f0(ppm)
(Topt=25°C, VCC=3V)CGOUT=0pF as standard
Test circuit
VCC
10
0
INTR
-10
Frequency
counter
-20
OSCIN
OSCOUT
CLKOUT
VDCC
CE
VDD
-30
0.1µF
-40
0
5
10
15
20
CGOUT(pF)
SCLK
CIN
SIO
VSS
0.1µF
Detector threshold voltage (+VDET1/-VDET1) vs. Operating temperature (Topt) (R2062K01)
Test circuit
2.9
VCC
±VDET1(V)
•
OSCOUT
CE
-3
0
•
OSCIN
1
+VDET1
2.8
INTR
-VDET1
CLKOUT
2.7
CE
OSCIN
OSCOUT
VDCC
VDD
0.1µF
2.6
-50
-25
0
25
50
75
100
Operating Temperature Topt(Celsius)
SCLK
CIN
SIO
VSS
0.1µF
49
R2062 series
•
VCC-VDD(VDDOUT1) vs. Output load current (IOUT1)
(Topt=25°C)
Test circuit
0
VCC
-0.1
VCC-VDD(V)
OSCIN
VCC=5V
OSCOUT
INTR
-0.2
VCC=3V
-0.3
CLKOUT
VDCC
VCC=2.5V
CE
-0.4
0.1µF
-0.5
0
2
4
6
8
•
VOL vs. IOL ( VDCC pin)
SIO
VSS
0.1µF
(Topt=25°C)
0.4
0.4
0.3
0.3
VOL(v)
VOL(v)
CIN
VOL vs. IOL ( INTR pin)
(Topt=25°C, VCC=VDD=2.0v)
0.2
VCC=3V
0.2
VCC=5V
0.1
0.1
0
0
0
1
2
3
IOL(mA)
50
SCLK
10
Output load current IOUT1(mA)
•
A
VDD
VCC=2.0V
4
5
6
0
2
4
6
IOL(mA)
8
10
R2062 series
Typical Software-based Operations
•
Initialization at Power-on
Start
*1)
Power-on
*2)
PON=1?
Yes
No
*3)
*4)
VDET=0?
Set Oscillation Adjustment
Register and Control
Register 1 and 2, etc.
No
Yes
Warning Back-up
Battery Run-down
*1) After power-on from 0 volt, the process of internal initialization require a time span on 1sec, so that
access should be done after VDCC turning to OFF(H).
*2) The PON bit setting of 0 in the Control Register 1 indicates power-on from backup battery and not from
0v. For further details, see "P.37 Power-on Reset, Oscillation Halt Sensing, and Supply Voltage
Monitoring •PON, XST , and VDET ".
*3) This step is not required when the supply voltage monitoring circuit is not used.
*4) This step involves ordinary initialization including the Oscillation Adjustment Register and interrupt
cycle settings, etc.
•
Writing of Time and Calendar Data
*1)
CE←H
Write to Time Counter and
Calendar Counter
CE←L
*2)
*3)
*1) When writing to clock and calendar counters, do not insert
CE=L until all times from second to year have been written to
prevent error in writing time. (Detailed in "P.29
•Considerations in Reading and Writing Time Data under
special condition".
*2) Any writing to the second counter will reset divider units lower
than the second digits.
The R2062 may also be initialized not at power-on but in the
process of writing time and calendar data.
51
R2062 series
•
Reading Time and Calendar Data
(1) Ordinary Process of Reading Time and Calendar Data
*1) When reading to clock and calendar counters, do not insert
CE=L until all times from second to year have been read to
prevent error in reading time. (Detailed in "P.29
•Considerations in Reading and Writing Time Data under
special condition".
*1)
CE←H
Read from Time Counter
and Calendar Counter
CE←L
*1)
(2) Basic Process of Reading Time and Calendar Data with Periodic Interrupt Function
Set Periodic Interrupt
Cycle Selection Bits
*1)
Generate Interrupt in CPU
No
CTFG=1?
Yes
*2)
Read from Time Counter
and Calendar Counter
*3)
Control Register 2
←(X1X1X011)
52
Other Interrupt
Processes
*1) This step is intended to select the level mode
as a waveform mode for the periodic interrupt
function.
*2) This step must be completed within 0.5
second.
*3) This step is intended to set the CTFG bit to 0
in the Control Register 2 to cancel an interrupt
to the CPU.
R2062 series
(3) Applied Process of Reading Time and Calendar Data with Periodic Interrupt Function
Time data need not be read from all the time counters when used for such ordinary purposes as time count
indication. This applied process can be used to read time and calendar data with substantial reductions in the
load involved in such reading.
For Time Indication in "Day-of-Month, Day-of-week, Hour, Minute, and Second" Format:
Control Register 1←
(XXXX0100)
Control Register 2←
(X1X1X011)
*1)
Generate interrupt to CPU
Yes
Other interrupts
Processes
No
CTFG=1?
*2)
Sec.=00?
No
Yes
Read Min.,Hr.,Day,
and Day-of-week
Control Register 2←
(X1X1X011)
*3)
Use Previous Min.,Hr.,
Day,and Day-of-week data
*1) This step is intended to select the
level mode as a waveform mode for
the periodic interrupt function.
*2) This step must be completed within
0.5 sec.
*3) This step is intended to read time
data from all the time counters only
in the first session of reading time
data after writing time data.
*4) This step is intended to set the
CTFG bit to 0 in the Control
Register 2 to cancel an interrupt to
the CPU.
*4)
53
R2062 series
•
Interrupt Process
(1) Periodic Interrupt
Set Periodic Interrupt
Cycle Selection Bits
*1)
Generate Interrupt to CPU
No
CTFG=1?
Yes
Conduct
Periodic Interrupt
*2)
Control Register 2←
(X1X1X011)
54
Other Interrupt
Processes
*1) This step is intended to select the level mode
as a waveform mode for the periodic interrupt
function.
*2) This step is intended to set the CTFG bit to 0
in the Control Register 2 to cancel an
interrupt to the CPU.
R2062 series
(2) Alarm Interrupt
WALE or DALE←0
*1)
Set Alarm Min., Hr., and
Day-of-week Registers
WALE or DALE←1
*2)
Generate Interrupt to CPU
No Other Interrupt
WAFG or DAFG=1?
Processes
Yes
*1) This step is intended to once disable the alarm
interrupt circuit by setting the WALE or DALE bits
to 0 in anticipation of the coincidental occurrence
of a match between current time and preset
alarm time in the process of setting the alarm
interrupt function.
*2) This step is intended to enable the alarm
interrupt function after completion of all alarm
interrupt settings.
*3) This step is intended to once cancel the alarm
interrupt function by writing the settings of
"X,1,X, 1,X,1,0,1" and "X,1,X,1,X,1,1,0" to the
Alarm_W Registers and the Alarm_D Registers,
respectively.
Conduct Alarm Interrupt
*3)
Control Register 2 ←
(X1X1X101)
55