SANYO AM-5416

Ordering number : ENA0056
AM-5416
Package Dimensions (unit : mm)
Light Receiving Side
Glass Juts(4 Corners)
Width : 1.0MAX, Length : 15.0MAX
(1.2)
B
100
±5
Lead Wires
34.3
(4.1)
±0.2
±0.5
52.0
Note: Glass Substrate Thickness
Module Thickness
Wire-Overcoat Thickness
Standard lead wires length
: 1.8mm
: 2.3mm max
: 3.3mm max (Including Module)
: 100mm Marking ( A & B )
Effective Area
±0.2
±0.5
36.7
(8)
Wire Overcoat
60.1
(18.35)
(15)
100
A
±5
(2.5)
Overcoat Side
Effective Area
Ratings at Ta = 25°C
Parameter
Symbol
Ratings
Conditions
min
typ
Unit
max
Open Circuit Voltage
Voc
SS 50kLx
3.1
V
Short Circuit Current
Isc
SS 50kLx
22.9
mA
Operating Voltage & Operating Current
Iope
Operating Temperature
Topr
Storage Temperature
Tstg
SS 50kLx, Vope=2.0V
AM-1.5, 100mW/cm2, Vope=2.0V
17.4
mA
49.9
mA
-5 to +40
°C
-20 to +70
°C
SS: Solar Simulator
Any and all SANYO Semiconductor products described or contained herein do not have specifications
that can handle applications that require extremely high levels of reliability, such as life-support systems,
aircraft's control systems, or other applications whose failure can be reasonably expected to result in
serious physical and/or material damage. Consult with your SANYO Semiconductor representative
nearest you before using any SANYO Semiconductor products described or contained herein in such
applications.
SANYO Semiconductor assumes no responsibility for equipment failures that result from using products
at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor
products described or contained herein.
90606 / D1505HKIM No.A0056-1/2
AM-5416
Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the
performance, characteristics, and functions of the described products in the independent state, and are
not guarantees of the performance, characteristics, and functions of the described products as mounted
in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an
independent device, the customer should always evaluate and test devices mounted in the customer's
products or equipment.
SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any
and all semiconductor products fail with some probability. It is possible that these probabilistic failures
could give rise to accidents or events that could endanger human lives, that could give rise to smoke or
fire, or that could cause damage to other property. When designing equipment, adopt safety measures
so that these kinds of accidents or events cannot occur. Such measures include but are not limited to
protective circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO Semiconductor products (including technical data,services) described
or contained herein are controlled under any of applicable local export control laws and regulations, such
products must not be exported without obtaining the export license from the authorities concerned in
accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or
otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO Semiconductor product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and
reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual
property rights or other rights of third parties.
This catalog provides information as of December, 2005. Specifications and information herein are subject
to change without notice.
PS No.A0056-2/2