STMICROELECTRONICS LD39150DT25-R

LD39150
Ultra low drop BICMOS voltage regulator
Feature summary
■
1.5A Guaranteed output current
■
Ultra low dropout voltage (200mV typ. @ 1.5A
load, 40mV typ. @300mA load)
■
Very low quiescent current (1mA typ. @ 1.5A
load, 1µA max @ 25°C in off mode)
DPAK
PPAK
■
Logic-controlled electronic shutdown
■
Current and thermal internal limit
■
±1.5% Output voltage tolerance @ 25°C
■
Fixed and ADJ output voltages: 1.22V, 1.8V,
2.5V, 3.3V, ADJ. (*see order code)
■
Temperature range: -40 to 125°C
■
Fast dynamic response to line and load
changes
Description
■
Stable with ceramic capacitor (see paragraph
7.1, 7.2, 7.3)
■
Available in PPAK, DPAK and DFN8 (4x4mm)
The LD39150 is a fast ultra low drop linear
regulator which operates from 2.5V to 6V input
supply.
Typical application
■
Microprocessor power supply
■
DSPs power supply
■
Post regulators for switching suppliers
■
High efficiency linear regulator
DFN8 (4x4 mm)
A wide range of output options are available. The
low drop voltage, low noise, and ultra low
quiescent current make it suitable for low voltage
microprocessor and memory applications. The
device is developed on a BiCMOS process which
allows low quiescent current operation
independently of output load current.
Order codes
Part numbers
DPAK (T&R)
DFN (1)
PPAK (T&R)
LD39150DT12-R
Output Voltage
LD39150PU12R
1.22V
LD39150DT18-R
LD39150PT18-R
LD39150PU18R
1.8V
LD39150DT25-R
LD39150PT25-R
LD39150PU25R
2.5V
LD39150DT33-R
LD39150PT33-R
LD39150PU33R
3.3V
LD39150PT-R
LD39150PU-R
ADJ From 1.22 to 5.0V
1. Available on request
January 2007
Rev. 1
1/19
www.st.com
19
LD39150
Contents
1
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Typical application circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6
Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7
Application notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.1
External capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.2
Input capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.3
Output capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.4
Thermal note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.5
Inhibit input operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
LD39150
Diagram
1
Diagram
Figure 1.
Block diagram
(*) Not present on ADJ Versions
3/19
Pin configuration
LD39150
2
Pin configuration
Figure 2.
Pin connections (top view for DPAK and PPAK, bottom view for DFN)
Table 1.
DPAK
PPAK
DFN8 (4x4 mm)
Pin description
PlN N°
DFN
8
SYMBOL
NOTE
VSENSE/N.C.
For fixed versions: to be connected with LDO Output Voltage pins for DFN
package and Not Connected on PPAK
PPAK DPAK
5
ADJ
For adjustable version: Error Amplifier Input pin for VO from 1.22 to 5.0V
3, 4
2
1
VI
LDO Input Voltage; VI from 2.5V to 6V, CI=1µF must be located at a
distance of not more than 0.5’’ from input pin.
6, 7
4
3
VO
LDO Output Voltage pins, with minimum CO=2.2µF needed for stability
(also refer to CO vs. ESR stability chart)
2
1
1
3
5
4/19
2
VINH
Inhibit Input Voltage: ON MODE when VINH ≥ 2V, OFF MODE when VINH ≤
0.3V (Do not leave floating, not internally pulled down/up)
GND
Common ground
N.C.
Not Connected
LD39150
3
Typical application circuits
Typical application circuits
(CI and CO Capacitors must be placed as close as possible to the IC pins)
Figure 3.
1
Figure 4.
LD39150 fixed version with inhibit
Inhibit Pin is not internally pulled down/up then it must not be left floating. Disable the device
when connected to GND or to a positive voltage less than 0.3V
LD39150 adjustable version
VO = VREF (1 + R1/R2)
2
Set R2 as close as possible to 4.7KΩ.
5/19
Typical application circuits
Figure 5.
LD39150 DPAK
Figure 6.
Timing diagram
6/19
LD39150
LD39150
Maximum ratings
4
Maximum ratings
Table 2.
Absolute maximum ratings
Symbol
VI
VINH
VO
VADJ
Parameter
Value
Unit
-0.3 to 6.5
V
INHIBIT Input voltage
-0.3 to VI +0.3 (6.5V Max)
V
DC Output voltage
-0.3 to VI +0.3 (6.5V Max)
V
ADJ Pin voltage
-0.3 to VI +0.3 (6.5V Max)
V
DC Input voltage
IO
Output current
Internally Limited
mA
PD
Power dissipation
Internally Limited
mW
TSTG
Storage temperature range
-50 to 150
°C
TOP
Operating junction temperature range
-40 to 125
°C
Note:
Absolute Maximum Ratings are those values beyond which damage to the device may
occur. Functional operation under these conditions is not implied. All values are referred to
GND.
Table 3.
Thermal Data
Symbol
Parameter
RthJA
Thermal resistance junction-ambient
RthJC
Thermal resistance junction-case
PPAK
DPAK
DFN (1)
Unit
100
100
40
°C/W
8
8
10
°C/W
1. With PCB ground plane heatsink.
7/19
Electrical characteristics
LD39150
5
Electrical characteristics
Table 4.
Electrical characteristics
(TJ = 25°C, VI = VO+1V, CI = 1µF, CO = 2.2µF, ILOAD = 10mA, VINH = 2V, unless otherwise
specified)
Symbol
VI
Parameter
Parameter
Operating input voltage
VI = VO+1V, ILOAD = 10mA to 1.5A
VO
Output voltage tolerance
VREF
Reference voltage
∆VO
Output voltage LINE
regulation
Output voltage LOAD
∆VO/∆ILOAD
regulation
VDROP
IQ
Dropout voltage (VI - VO)
VI = VO+1V to 6V,
ILOAD = 10mA to 1.5A
TJ = -40 to 125°C
Min.
Typ.
Max.
Unit
2.5
6
V
-1.5
1.5
-3
3
% of
VO(NOM)
1.22
V
VI = VO+1V to 6V
0.04
%
VI = VO+1V to 6V, TJ = -40 to 125°C
0.1
ILOAD = 10mA to 1.5A
0.06
ILOAD = 10mA to 1.5A,
TJ = -40 to 125°C
0.2
0.4
ILOAD = 300mA, TJ=-40 to 125°C
40
80
ILOAD = 1.5A, TJ = -40 to 125°C
200
400
1
2.5
0.2
%
%/A
mV
Quiescent current:
ON MODE
ILOAD = 10mA to 1.5A, VINH = 2V
TJ = -40 to 125°C
Quiescent current:
OFF MODE
VINH = 0.3V
1
VINH = 0.3V, TJ = -40 to 125°C
5
mA
µA
Short Circuit Protection
Short circuit protection
RL = 0
Inhibit threshold LOW
Inhibit threshold HIGH
VI = 2.5 to 6V OFF
TJ = -40 to 125°C
TD-OFF
Current limit
ILOAD = 1.5A, VO = 3.3V
15
TD-ON
Current limit
ILOAD = 1.5A, VO = 3.3V
15
Inhibit input current (1)
VI = 6V, VINH = 0 to 6V
±0.1
ISC
3
A
Inhibit Input
VINH
IINH
0.3
V
2
µs
±1
µA
AC Parameters
SVR
eN
TSHDN
Supply voltage rejection
Output noise voltage
f = 120Hz
65
f = 1kHz
55
dB
BW = 10Hz to 100kHz,
CO = 2.2µF, VO = 2.5V
100
Thermal shutdown OFF
170
Hysteresis
10
µVRMS
°C
1. Guaranteed by design
8/19
VI = 4.5 ± 1V,
VO = 3.3V,
ILOAD = 10mA,
LD39150
Typical performance characteristics
6
Typical performance characteristics
Figure 7.
(TJ = 25°C, VI = VO+1V, CI = 1µF, CO = 2.2µF, ILOAD = 10mA, VINH = VI, unless otherwise
specified)
Output voltage vs temperature
Figure 8.
Dropout voltage vs temperature
Figure 9.
Dropout voltage vs output current
Figure 11. Quiescent current vs temperature
Figure 10. Quiescent current vs supply
voltage
Figure 12. Quiescent current vs temperature
9/19
Typical performance characteristics
LD39150
Figure 13. Short circuit current vs temperature Figure 14. Output voltage vs input voltage
Figure 15. Stability region vs CO & ESR (at
100kHz)
Figure 16. Stability region vs CO & Low ESR
(at 100kHz)
Figure 17. Load transient
Figure 18. Line transient
VI = 3.5V, IO = 10mA to 1.5A, CI = 1µF, CO = 2.2µF
VI = 3.5V to 5.5V, ILOAD = 10mA, CO = 2.2µF
10/19
LD39150
Application notes
7
Application notes
7.1
External capacitors
The LD39150 requires external capacitors for regulator stability. These capacitors must be
selected to meet the requirements of minimum capacitance and equivalent series resistance
(see Figure 15. Figure 16.). The input/output capacitors must be located less than 1cm from
the relative pins and connected directly to the input/output ground pins using traces which
have no other currents flowing through them. Any good quality of Ceramic or Electrolytic
capacitors can be used.
7.2
Input capacitor
An input capacitor whose minimum value is 1µF is required with the LD39150 (amount of
capacitance can be increased without limit). This capacitor must be located a distance of not
more than 1cm from the input pin of the device and returned to a clean analog ground. Any
good quality ceramic, tantalum or film capacitors can be used for this capacitor.
7.3
Output capacitor
It is possible to use Ceramic or Tantalum capacitors but the output capacitor must meet the
requirement for minimum amount of capacitance and E.S.R. (equivalent series resistance)
value. A minimum capacitance of 2.2µF is a good choice to guarantee the stability of the
regulator. Anyway, other CO values can be used according to the (Figure 15. Figure 16.)
showing the allowable ESR range as a function of the output capacitance. This curve
represents the stability region over the full temperature and IO range.
7.4
Thermal note
The output capacitor must maintain its ESR in the stable region over the full operating
temperature range to assure stability. Also, capacitors tolerance and variation with
temperature must be kept in consideration in order to assure the minimum amount of
capacitance at all times.
7.5
Inhibit input operation
The inhibit pin can be used to turn OFF the regulator when pulled down, so drastically
reducing the current consumption down to less than 1µA. When the inhibit feature is not
used, this pin must be tied to VI to keep the regulator output ON at all times. To assure
proper operation, the signal source used to drive the inhibit pin must be able to swing above
and below the specified thresholds listed in the electrical characteristics section (VIH VIL).
The inhibit pin must not be left floating because it is not internally pulled down/up.
11/19
Package mechanical data
8
LD39150
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
12/19
LD39150
Package mechanical data
PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
2.2
2.4
0.086
0.094
A1
0.9
1.1
0.035
0.043
A2
0.03
0.23
0.001
0.009
B
0.4
0.6
0.015
0.023
B2
5.2
5.4
0.204
0.212
0.023
C
0.45
0.6
0.017
C2
0.48
0.6
0.019
0.023
D
6
6.2
0.236
0.244
6.6
0.252
D1
E
5.1
6.4
0.201
0.260
E1
4.7
0.185
e
1.27
0.050
G
4.9
G1
2.38
2.7
0.093
0.106
H
9.35
10.1
0.368
0.397
L2
0.8
L4
0.6
L5
1
L6
5.25
1
1
2.8
0.193
0.206
0.031
0.023
0.039
0.039
0.039
0.110
0078180-E
13/19
Package mechanical data
LD39150
DPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
2.2
2.4
0.086
0.094
A1
0.9
1.1
0.035
0.043
A2
0.03
0.23
0.001
0.009
B
0.64
0.9
0.025
0.035
b4
5.2
5.4
0.204
0.212
C
0.45
0.6
0.017
0.023
C2
0.48
0.6
0.019
0.023
D
6
6.2
0.236
0.244
6.6
0.252
D1
E
5.1
6.4
E1
0.200
4.7
e
0.260
0.185
2.28
0.090
e1
4.4
4.6
0.173
0.181
H
9.35
10.1
0.368
0.397
L
1
0.039
(L1)
2.8
0.110
L2
0.8
0.031
L4
0.6
1
0.023
0.039
0068772-F
14/19
LD39150
Package mechanical data
DFN8 (4x4) MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
0.80
0.90
1.00
0.031
0.035
0.039
A1
0
0.02
0.05
0
0.001
0.002
A3
0.20
0.008
b
0.23
0.30
0.38
0.009
0.012
0.015
D
3.90
4.00
4.10
0.154
0.157
0.161
D2
2.82
3.00
3.23
0.111
0.118
0.127
E
3.90
4.00
4.10
0.154
0.157
0.161
E2
2.05
2.20
2.30
0.081
0.087
0.091
e
L
0.80
0.40
0.50
0.031
0.60
0.016
0.020
0.024
7869653B
15/19
Package mechanical data
LD39150
Tape & Reel DPAK-PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MIN.
TYP.
330
13.0
13.2
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
16/19
MAX.
0.504
0.512
22.4
0.519
0.882
Ao
6.80
6.90
7.00
0.268
0.272
0.2.76
Bo
10.40
10.50
10.60
0.409
0.413
0.417
Ko
2.55
2.65
2.75
0.100
0.104
0.105
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
7.9
8.0
8.1
0.311
0.315
0.319
LD39150
Package mechanical data
Tape & Reel QFNxx/DFNxx (4x4) MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
330
C
12.8
D
20.2
N
99
13.2
MAX.
12.992
0.504
0.519
0.795
101
T
3.898
3.976
14.4
0.567
Ao
4.35
0.171
Bo
4.35
0.171
Ko
1.1
0.043
Po
4
0.157
P
8
0.315
17/19
Revision history
LD39150
9
Revision history
Table 5.
Revision history
Date
Revision
26-Jan-2007
1
18/19
Changes
Initial release.
LD39150
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
19/19