STMICROELECTRONICS LRI64-A7T

LRI64
Memory TAG IC at 13.56 MHz, with 64-bit Unique ID and WORM
user area, ISO15693 and ISO18000-3 Mode 1 compliant
Features
■
ISO 15693 Compliant
■
ISO 18000-3 Mode 1 compliant
■
13.56 MHz ±7 kHz carrier frequency
■
Supported data transfer to the LRI64:
10% ASK modulation using “1-out-of-4” pulse
position coding (26 Kbit/s)
■
Supported data transfer from the LRI64:
Load modulation using Manchester coding with
423 kHz single sub-carrier in fast data rate
(26 Kbit/s)
■
Internal tuning capacitor (21 pF, 28.5 pF,
97 pF)
■
7 × 8 bits WORM user area
■
64-bit Unique Identifier (UID)
■
Read Block and Write Block Commands (8-bit
blocks)
■
7 ms Programming time (typical)
■
More than 40-year data retention
■
Electrical Article Surveillance capable
(software controlled)
■
Packages
– ECOPACK® (RoHS compliant)
Antenna (A1)
Antenna (A6)
Antenna (A7)
UFDFPN8 (MB)
2 × 3 mm² (MLP)
Wafer
February 2007
Rev 6
1/52
www.st.com
1
Contents
LRI64
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1
Memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2
Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4
3.1
Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2
Stay Quiet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3
Read Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4
Write Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.5
Get_System_Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.6
Initial Dialogue for Vicinity Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2
Operating field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5
Communication signal from VCD to LRI64 . . . . . . . . . . . . . . . . . . . . . . 11
6
Data rate and data coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7
VCD to LRI64 frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8
Communications signal from LRI64 to VCD . . . . . . . . . . . . . . . . . . . . . 14
9
8.1
Load modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.2
Subcarrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.3
Data rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.4
Bit representation and coding using one subcarrier, at the high data rate 14
Logic 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.4.2
Logic 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LRI64 to VCD frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9.1
2/52
8.4.1
LRI64 SOF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LRI64
Contents
9.2
10
LRI64 EOF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Special fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
10.1
Unique Identifier (UID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
10.2
Application Family Identifier (AFI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10.3
Data Storage Format Identifier (DSFID) . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10.4
Cyclic Redundancy Code (CRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
11
LRI64 protocol description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
12
LRI64 states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
13
14
15
16
12.1
Power-off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
12.2
Ready state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
12.3
Quiet state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
13.1
Addressed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
13.2
Non-addressed mode (General Request) . . . . . . . . . . . . . . . . . . . . . . . . 22
Flags and error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
14.1
Request flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
14.2
Response flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
14.3
Response error code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Anti-collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
15.1
Request flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
15.2
Mask length and mask value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
15.3
Inventory responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Request processing by the LRI64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
16.1
17
Explanation of the possible cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Timing definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
17.1
LRI64 response delay, t1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
17.2
VCD new request delay, t2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
17.3
VCD new request delay when there is no LRI64 response, t3 . . . . . . . . . 31
3/52
Contents
18
LRI64
Command codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
18.1
Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
18.2
Stay Quiet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
18.3
Read Single Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
18.4
Write Single Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
18.5
Get System Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
19
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
20
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
21
Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
22
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Appendix A algorithm for pulsed slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Appendix B C-example to calculate or check the CRC16
according to ISO/IEC 13239 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
22.1
CRC calculation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Appendix C Application family identifier (AFI) coding . . . . . . . . . . . . . . . . . . . . 50
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4/52
LRI64
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
10% modulation parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Request flags 1 to 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Request flags 5 to 8 (when bit 3 = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Request flags 5 to 8 (when bit 3 = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Response flags 1 to 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Response error code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Timing values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Command codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Block lock status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
A1 Antenna on tape mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
A6 Antenna on tape mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
A7 Antenna on tape mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
UFDFPN8 (MLP8), 8-lead Ultra thin Fine pitch Dual Flat Package No lead
2 × 3 mm, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CRC definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
AFI coding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
5/52
List of figures
LRI64
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
6/52
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MLP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
LRI64 memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
10% modulation waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
“1-out-of-4” coding example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
“1-out-of-4” coding mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Request SOF, using the “1-out-of-4” data coding mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Request EOF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Logic 0, high data rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Logic 1, high data rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Response SOF, using high data rate and one subcarrier. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Response EOF, using high data rate and one subcarrier. . . . . . . . . . . . . . . . . . . . . . . . . . 16
UID format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Decision tree for AFI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CRC format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VCD request frame format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LRI64 response frame format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
LRI64 protocol timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
LRI64 state transition diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Comparison between the Mask, Slot Number and UID . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Description of a possible anti-collision sequence between LRI64 devices . . . . . . . . . . . . . 29
Inventory, request frame format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Inventory, response frame format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Stay Quiet, request frame format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Stay Quiet frame exchange between VCD and LRI64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Read Single Block, request frame format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Read Single Block, response frame format, when Error_Flag is not set . . . . . . . . . . . . . . 34
Read Single Block, response frame format, when Error_Flag is set . . . . . . . . . . . . . . . . . 34
READ Single Block frame exchange between VCD and LRI64 . . . . . . . . . . . . . . . . . . . . . 35
Write Single Block, request frame format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Write Single Block, response frame format, when Error_Flag is not set. . . . . . . . . . . . . . . 35
Write Single Block, response frame format, when Error_Flag is set. . . . . . . . . . . . . . . . . . 36
Write Single Block frame exchange between VCD and LRI64 . . . . . . . . . . . . . . . . . . . . . . 36
Get System Info, request frame format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Get System Info, response frame format, when Error_Flag is not set . . . . . . . . . . . . . . . . 37
Get System Info, response frame format, when Error_Flag is set . . . . . . . . . . . . . . . . . . . 37
Get System Info frame exchange between VCD and LRI64 . . . . . . . . . . . . . . . . . . . . . . . 38
LRI64 synchronous timing, transmit and receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
A1 Antenna on tape outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
A6 Antenna on tape outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
A7 Antenna on tape outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8-lead Ultra thin Fine pitch Dual Flat Package No lead (MLP) outline . . . . . . . . . . . . . . . . 45
LRI64
1
Description
Description
The LRI64 is a contactless memory, powered by an externally transmitted radio wave. It
contains a 120-bit non-volatile memory. The memory is organized as 15 blocks of 8 bits, of
which 7 blocks are accessible as Write-Once Read-Many (WORM) memory.
Figure 1.
Logic diagram
LRI64
Power
Supply
Regulator
120-bit
WORM
Memory
AC1
ASK
Demodulator
Manchester
Load
Modulator
AC0
AI08590
The LRI64 is accessed using a 13.56 MHz carrier wave. Incoming data are demodulated
from the received Amplitude Shift Keying (ASK) signal, 10% modulated. The data are
transferred from the reader to the LRI64 at 26 Kbit/s, using the “1-out-of-4” pulse encoding
mode.
Outgoing data are sent by the LRI64, generated by load variation on the carrier wave, using
Manchester coding with a single sub-carrier frequency of 423 kHz. The data are transferred
from the LRI64 to the reader at 26 Kbit/s, in the high data rate mode.
The LRI64 supports the high data rate communication protocols of ISO 15693 and ISO
18000-3 Mode 1 recommendations. All other data rates and modulations are not supported
by the LRI64.
Table 1.
Signal names
AC1
Antenna Coil
AC0
Antenna Coil
Figure 2.
MLP connections
AC0
n/c
n/c
n/c
1
2
3
4
8
7
6
5
AC1
n/c
n/c
n/c
AI11612
1. n/c means not connected internally.
7/52
Description
1.1
LRI64
Memory mapping
The LRI64 is organized as 15 blocks of 8 bits as shown in Figure 3. Each block is
automatically write-protected after the first valid write access.
Figure 3.
LRI64 memory mapping
0 1 2 3 4 5 6 7
Block
Addr
0
UID 0
1
UID 1
2
UID 2
3
UID 3
4
UID 4
5
UID 5 = IC_ID
6
UID 6 = 02h
7
UID 7 = E0h
8
AFI (WORM Area)
9
DSFID (WORM Area)
10
WORM Area
11
WORM Area
12
WORM Area
13
WORM Area
14
WORM Area
AI09741
The LRI64 uses the first 8 blocks (blocks 0 to 7) to store the 64-bit Unique Identifier (UID).
The UID is used during the anti-collision sequence (Inventory). It is written, by ST, at time of
manufacture, but part of it can be customer-accessible and customer-writable, on special
request.
The LRI64 has an AFI register, in which to store the Application Family Identifier value,
which is also used during the anti-collision sequence.
The LRI64 has a DSFID register, in which to store the Data Storage Format Identifier value,
which is used for the LRI64 Inventory answer.
The five following blocks (blocks 10 to 14) are Write-Once Read-Many (WORM) memory. It
is possible to write to each of them once. After the first valid write access, the block is
automatically locked, and only read commands are possible.
8/52
LRI64
2
Signal description
Signal description
AC1, AC0
The pads for the Antenna Coil. AC1 and AC0 must be directly bonded to the antenna.
3
Commands
The LRI64 supports the following commands:
3.1
Inventory
Used to perform the anti-collision sequence. The LRI64 answers to the Inventory command
when all of the 64 bits of the UID have been correctly written.
3.2
Stay Quiet
Used to put the LRI64 in Quiet mode. In this mode, the LRI64 only responds to commands
in Addressed mode.
3.3
Read Block
Used to output the 8 bits of the selected block.
3.4
Write Block
Used to write a new 8-bit value in the selected block, provided that the block is not locked.
This command can be issued only once to each block.
3.5
Get_System_Info
Used to allow the application system to identify the product. It gives the LRI64 memory size,
and IC reference (IC_ID).
3.6
Initial Dialogue for Vicinity Cards
The dialogue between the Vicinity Coupling Device (VCD) and the LRI64 is conducted
according to a technique called Reader Talk First (RTF). This involves the following
sequence of operations:
1.
activation of the LRI64 by the RF operating field of the VCD
2.
transmission of a command by the VCD
3.
transmission of a response by the LRI64
9/52
Power transfer
4
LRI64
Power transfer
Power transfer to the LRI64 is accomplished by inductive coupling of the 13.56MHz radio
signal between the antennas of the LRI64 and VCD. The RF field transmitted by the VCD
induces an AC voltage on the LRI64 antenna, which is then rectified, smoothed and voltageregulated. Any amplitude modulation present on the signal is demodulated by the Amplitude
Shift Keying (ASK) demodulator.
4.1
Frequency
ISO 15693 and ISO 18000-3 Mode 1 standards define the carrier frequency (fC) of the
operating field to be 13.56MHz±7kHz.
4.2
Operating field
The LRI64 operates continuously between Hmin and Hmax.
●
The minimum operating field is Hmin and has a value of 150mA/m (rms).
●
The maximum operating field is Hmax and has a value of 5A/m (rms).
A VCD generates a field of at least Hmin and not exceeding Hmax in the operating volume.
10/52
LRI64
5
Communication signal from VCD to LRI64
Communication signal from VCD to LRI64
Communications between the VCD and the LRI64 involves a type of Amplitude Modulation
called Amplitude Shift Keying (ASK).
The LRI64 only supports the 10% modulation mode specified in ISO 15693 and ISO 180003 Mode 1 standards. Any request that the VCD might send using the 100% modulation
mode, is ignored, and the LRI64 remains in its current state. However, the LRI64 is, in fact,
operational for any degree of modulation index from between 10% and 30%.
The modulation index is defined as (a-b)/(a+b) where a and b are the peak and minimum
signal amplitude, respectively, of the carrier frequency, as shown in Figure 4.
Table 2.
Figure 4.
10% modulation parameters
Parameter
Min
Max
hr
–
0.1 x (a-b)
hf
–
0.1 x (a-b)
10% modulation waveform
hf
hr
tRFF
a
tRFSFL
tRFR
b
t
AI06655B
Figure 5.
“1-out-of-4” coding example
10
00
01
11
75.52 µs
75.52 µs
75.52 µs
75.52 µs
AI06659B
11/52
Data rate and data coding
6
LRI64
Data rate and data coding
The data coding method involves pulse position modulation. The LRI64 supports the “1-outof-4” pulse coding mode. Any request that the VCD might send in the “1-out-of-256” pulse
coded mode, is ignored, and the LRI64 remains in its current state.
Two bit values are encoded at a time, by the positioning of a pause of the carrier frequency
in one of four possible 18.88µs (256/fC) time slots, as shown in Figure 6.
Four successive pairs of bits form a byte. The transmission of one byte takes 302.08 µs and,
consequently, the data rate is 26.48 kbits/s (fC/512).
The encoding for the least significant pair of bits is transmitted first. For example Figure 5
shows the transmission of E1h (225d, 1110 0001b) by the VCD.
Figure 6.
“1-out-of-4” coding mode
Pulse position for "00"
9.44 µs
9.44 µs
75.52 µs
Pulse position for "01" (1=LSB)
28.32 µs
9.44 µs
75.52 µs
Pulse position for "10" (0=LSB)
47.20µs
Pulse position for "11"
9.44 µs
75.52 µs
66.08 µs
9.44 µs
75.52 µs
AI06658
12/52
LRI64
7
VCD to LRI64 frames
VCD to LRI64 frames
Request Frames are delimited by a Start of Frame (SOF) and an End of Frame (EOF) and
are implemented using a code violation mechanism. Unused options are reserved for future
use.
The LRI64 is ready to receive a new command frame from the VCD after a delay of t2 (see
Table 14) after having sent a response frame to the VCD.
The LRI64 generates a Power On delay of tPOR (see Table 14) after being activated by the
powering field. After this delay, the LRI64 is ready to receive a command frame from the
VCD.
In ISO 15693 and ISO 18000-3 Mode 1 standards, the SOF is used to define the data
coding mode that the VCD is going to use in the following command frame.
The SOF that is shown in Figure 7 selects the “1-out-of-4” data coding mode. (The LRI64
does not support the SOF for the “1-out-of-256” data coding mode.)
The corresponding EOF sequence is shown in Figure 8.
Figure 7.
Request SOF, using the “1-out-of-4” data coding mode
9.44 µs
9.44 µs
9.44 µs
37.76 µs
37.76 µs
AI06660
Figure 8.
Request EOF
9.44 µs
9.44 µs
37.76 µs
AI06662
13/52
Communications signal from LRI64 to VCD
8
LRI64
Communications signal from LRI64 to VCD
ISO 15693 and ISO 18000-3 Mode 1 standards define several modes, for some parameters,
to cater for use in different application requirements and noise environments. The LRI64
does not support all of these modes, but supports the single subcarrier mode at the fast
data rate.
8.1
Load modulation
The LRI64 is capable of communication to the VCD via the inductive coupling between the
two antennas. The carrier is loaded, with a subcarrier with frequency fS, generated by
switching a load in the LRI64.
The amplitude of the variation to the signal, as received on the VCD antenna, is at least
10mV, when measured as described in the test methods defined in International Standard
ISO10373-7.
8.2
Subcarrier
The LRI64 supports the one subcarrier modulation response format. This format is selected
by the VCD using the first bit in the protocol header.
The frequency, fS, of the subcarrier load modulation is 423.75kHz (=fC/32).
8.3
Data rate
The LRI64 response uses the high data rate format (26.48 kbits/s). The selection of the data
rate is made by the VCD using the second bit in the protocol header.
8.4
Bit representation and coding using one subcarrier, at the
high data rate
Data bits are encoded using Manchester coding, as described in Figure 9 and Figure 10.
8.4.1
Logic 0
A logic 0 starts with 8 pulses of 423.75 kHz (fC/32) followed by an unmodulated period of
18.88 µs as shown in Figure 9.
Figure 9.
Logic 0, high data rate
37.76 µs
AI06663
14/52
LRI64
8.4.2
Communications signal from LRI64 to VCD
Logic 1
A logic 1 starts with an unmodulated period of 18.88 µs followed by 8 pulses of 423.75 kHz
(fC/32) as shown in Figure 10.
Figure 10. Logic 1, high data rate
37.76 µs
AI06664
15/52
LRI64 to VCD frames
9
LRI64
LRI64 to VCD frames
Response Frames are delimited by a Start of Frame (SOF) and an End of Frame (EOF) and
are implemented using a code violation mechanism. The LRI64 supports these in the one
subcarrier mode, at the fast data rate, only.
The VCD is ready to receive a response frame from the LRI64 before 320.9µs (t1) after
having sent a command frame.
9.1
LRI64 SOF
SOF comprises three parts: (see Figure 11)
9.2
●
an unmodulated period of 56.64 µs,
●
24 pulses of 423.75 kHz (fc/32),
●
a logic 1 which starts with an unmodulated period of 18.88 µs followed by 8 pulses of
423.75 kHz.
LRI64 EOF
EOF comprises three parts: (see Figure 12)
●
a logic 0 which starts with 8 pulses of 423.75 kHz followed by an unmodulated period of
18.88 µs.
●
24 pulses of 423.75 kHz (fC/32),
●
an unmodulated time of 56.64 µs.
Figure 11. Response SOF, using high data rate and one subcarrier
113.28 µs
37.76 µs
AI06671B
Figure 12. Response EOF, using high data rate and one subcarrier
37.76 µs
113.28 µs
AI06675B
16/52
LRI64
Special fields
10
Special fields
10.1
Unique Identifier (UID)
Members of the LRI64 family are uniquely identified by a 64-bit Unique Identifier (UID). This
is used for addressing each LRI64 device uniquely and individually, during the anti-collision
loop and for one-to-one exchange between a VCD and an LRI64.
The UID complies with ISO/IEC 15963 and ISO/IEC 7816-6. It is a read-only code, and
comprises (as summarized in Figure 13):
●
8-bit prefix, the most significant bits, set at E0h
●
8-bit IC Manufacturer code (ISO/IEC 7816-6/AM1), set at 02h (for STMicroelectronics)
●
48-bit Unique Serial Number
Figure 13. UID format
Most significant bits
63
55
47
E0h
Least significant bits
0
02h
Unique Serial Number
AI09725
Figure 14. Decision tree for AFI
Inventory Request
Received
No
AFI Flag
Set ?
Yes
AFI value
=0?
No
Yes
AFI value
= Internal
value ?
No
Yes
Answer given by the VICC
to the Inventory Request
No Answer
AI06679B
17/52
Special fields
10.2
LRI64
Application Family Identifier (AFI)
The Application Family Identifier (AFI) indicates the type of application targeted by the VCD,
and is used to select only those LRI64 devices meeting the required application criteria (as
summarized in Figure 14). The value is programmed by the LRI64 issuer in the AFI register.
Once programmed, it cannot be modified.
The most significant nibble of the AFI is used to indicate one specific application, or all
families. The least significant nibble of the AFI is used to code one specific sub-families, or
all sub-families. Sub-family codes, other than 0, are proprietary (as described in ISO 15693
and ISO 18000-3 Mode 1 documentation).
10.3
Data Storage Format Identifier (DSFID)
The Data Storage Format Identifier (DSFID) indicates how the data is structured in the
LRI64 memory. It is coded on one byte. It allows for quick and brief knowledge on the logical
organization of the data. It is programmed by the LRI64 issuer in the DSFID register. Once
programmed, it cannot be modified.
10.4
Cyclic Redundancy Code (CRC)
The Cyclic Redundancy Code (CRC) is calculated as defined in ISO/IEC 13239, starting
from an initial register content of all ones: FFFFh.
The 2-byte CRC is appended to each Request and each Response, within each frame,
before the EOF. The CRC is calculated on all the bytes after the SOF, up to the CRC field.
Upon reception of a Request from the VCD, the LRI64 verifies that the CRC value is valid. If
it is invalid, it discards the frame, and does not answer the VCD.
Upon reception of a Response from the LRI64, it is recommended that the VCD verify that
the CRC value is valid. If it is invalid, the actions that need to be performed are up to the
VCD designer.
The CRC is transmitted Least Significant Byte first. Each byte is transmitted Least
Significant Bit first, as shown in Figure 15).
Figure 15. CRC format
Least Significant Byte Most Significant Byte
l.s.bit
m.s.bit l.s.bit
m.s.bit
AI09726
18/52
LRI64
11
LRI64 protocol description
LRI64 protocol description
The Transmission protocol defines the mechanism to exchange instructions and data
between the VCD and the LRI64, in each direction. Based on “VCD talks first”, the LRI64
does not start transmitting unless it has received and properly decoded an instruction sent
by the VCD.
The protocol is based on an exchange of:
●
a Request from the VCD to the LRI64
●
a Response from the LRI64 to the VCD
Each Request and each Response are contained in a Frame. The frame delimiters (SOF,
EOF) are described in the previous paragraphs.
Each Request (Figure 16) consists of:
●
Request SOF (Figure 7)
●
Request Flags (Table 3 to Table 5)
●
Command Code
●
Parameters (depending on the Command)
●
Application Data
●
2-byte CRC (Figure 15)
●
Request EOF (Figure 8)
Each Response (Figure 17) consists of:
●
Response SOF (Figure 11)
●
Response Flags (Table 6)
●
Parameters (depending on the Command)
●
Application Data
●
2-byte CRC (Figure 15)
●
Response EOF (Figure 12)
The number of bits transmitted in a frame is a multiple of eight, and thus always an integer
number of bytes.
Single-byte fields are transmitted Least Significant Bit first.
Multiple-byte fields are transmitted Least Significant Byte first, with each byte transmitted
Least Significant Bit first.
The setting of the flags indicates the presence of any optional fields. When the flag is set, 1,
the field is present. When the flag is reset, 0, the field is absent.
Figure 16. VCD request frame format
Request
SOF
Request Command
Flags
Code
Parameters
Data
2-Byte
CRC
Request
EOF
AI09727
19/52
LRI64 protocol description
LRI64
Figure 17. LRI64 response frame format
Response Response
SOF
Flags
Parameters
Data
2-Byte
CRC
Response
EOF
AI09728
Figure 18. LRI64 protocol timing
VCD
Request Frame
Request Frame
Response Frame
VICC
Timing
t1
Response Frame
t2
t1
t2
AI06830B
20/52
LRI64
12
LRI64 states
LRI64 states
A LRI64 can be in any one of three states:
●
Power-off
●
Ready
●
Quiet
Transitions between these states are as specified in Figure 19.
12.1
Power-off state
The LRI64 is in the Power-off state when it receives insufficient energy from the VCD.
12.2
Ready state
The LRI64 is in the Ready state when it receives enough energy from the VCD. It answers to
any Request in Addressed and Non-addressed modes.
12.3
Quiet state
When in the Quiet State, the LRI64 answers to any Request in Addressed mode.
21/52
Modes
13
LRI64
Modes
The term mode refers to the mechanism for specifying, in a Request, the set of LRI64
devices that shall answer to the Request.
13.1
Addressed mode
When the Address_flag is set to 1 (Addressed mode), the Request contains the Unique ID
(UID) of the addressed LRI64 device (such as an LRI64 device). Any LRI64 receiving a
Request in which the Address_flag is set to 1, compares the received Unique ID to its own
UID. If it matches, it execute the Request (if possible) and returns a Response to the VCD,
as specified by the command description. If it does not match, the LRI64 device remains
silent.
13.2
Non-addressed mode (General Request)
When the Address_flag is set to 0 (Non-addressed mode), the Request does not contain a
Unique ID field. Any LRI64 device receiving a Request in which the Address_flag is set to 0,
executes the Request and returns a Response to the VCD as specified by the command
description.
Figure 19. LRI64 state transition diagram
Power Off
Out of
field
Out of
field
In field
Ready
Inventory (if UID written)
Write, Read, Get_System_Info
in addressed and
non-addressed modes
Stay quiet(UID)
Quiet
Write, Read, Get_System_Info
in addressed mode
AI09723
22/52
LRI64
Flags and error codes
14
Flags and error codes
14.1
Request flags
In a Request, the 8-bit Flags Field specifies the actions to be performed by the LRI64, and
whether corresponding fields are present or not.
Flag bit 3 (the Inventory_flag) defines the way the four most significant flag bits (5 to 8) are
used. When bit 3 is reset (0), bits 5 to 8 define the LRI64 selection criteria. When bit 3 is set
(1), bits 5 to 8 define the LRI64 Inventory parameters.
Table 3.
Request flags 1 to 4
Bit
Value (1)
Name
Description
1
Sub-carrier Flag
0
Single sub-carrier frequency mode.
(Option 1 is not supported)
2
Data_rate Flag
1
High data rate mode.
(Option 0 is not supported)
0
Flags 5 to 8 meaning are according to Table 4
3
Inventory Flag
1
Flags 5 to 8 meaning are according to Table 5
0
No Protocol format extension. Must be set to 0.
(Option 1 is not supported)
Protocol Extension
Flag
4
1. If the value of the Request Flag is a non authorized value, the LRI64 does not execute the command, and
does not respond to the request.
Table 4.
Bit
5
6
Request flags 5 to 8 (when bit 3 = 0)
Name
Select Flag
Value(1)
Description
0
No selection mode.
Must be set to 0.
(Option 1 is not supported)
0
Non addressed mode.
The UID field is not present in the request. All LRI64 shall
answer to the request.
1
Addressed mode.
The UID field is present in the request. Only the LRI64 that
matches the UID answers the request.
Address Flag
7
Option Flag(1)
0
No option. Must be set to 0.
(Option 1 is not supported)
8
RFU(1)
0
No option. Must be set to 0.
(Option 1 is not supported)
1. Only bit 6 (Address flag) can be configured for the LRI64. All others bits (5, 7 and 8) must be reset to 0.
23/52
Flags and error codes
Table 5.
LRI64
Request flags 5 to 8 (when bit 3 = 1)
Bit
5
6
Value(1)
Name
Description
0
AFI field is not present
1
AFI field is present
0
16 slots
1
1 slot
AFI Flag
Nb_slots Flag
7
Option Flag
0
No option. Must be set to 0.
(Option 1 is not supported)
8
RFU
0
No option. Must be set to 0.
(Option 1 is not supported)
1. Bits 7 and 8 must be reset to 0.
14.2
Response flags
In a Response, the 8-bit Flags Field indicates how actions have been performed by the
LRI64, and whether corresponding fields are present or not.
Table 6.
Response flags 1 to 8
Bit
1
14.3
Name
Value
Description
0
No error
1
Error detected. Error code is in the "Error" field.
Error Flag
2
RFU
0
3
RFU
0
4
RFU
0
5
RFU
0
6
RFU
0
7
RFU
0
8
RFU
0
Response error code
If the Error Flag is set by the LRI64 in the Response, the Error Code Field is present and
provides information about the error that occurred. Table 7 shows the one error code that is
supported by the LRI64.
Table 7.
24/52
Response error code
Error code
Meaning
0Fh
Error with no specific information given
LRI64
15
Anti-collision
Anti-collision
The purpose of the anti-collision sequence is to allow the VCD to compile a list of the LRI64
devices that are present in the VCD field, each one identified by its unique ID (UID).
The VCD is the master of the communication with one or multiple LRI64 devices. It initiates
the communication by issuing the Inventory Request (Figure 22).
15.1
Request flags
The Nb_slots_flag needs to be set appropriately. The AFI Flag needs to be set, if the
Optional AFI Field is to be present.
15.2
Mask length and mask value
The Mask Length defines the number of significant bits in the Mask Value.
The Mask Value is contained in an integer number of bytes.
The least significant bit of each is transmitted first.
If the Mask Length is not a multiple of 8 (bits), the most significant end of the Mask Value is
padded with the required number of null bits (set to 0) so that the Mask Value is contained in
an integer number of bytes, so that the next field (the 2-Byte CRC) starts at the next byte
boundary.
In the example of Figure 20, the Mask Length is 11 bits. The Mask Value, 10011001111, is
padded out at the most significant end with five bits set to 0. The 11 bits Mask plus the
current slot number is compared to the UID.
15.3
Inventory responses
Each LRI64 sends its Response in a given time slot, or else remains silent.
The first slot starts immediately after the reception of the Request EOF.
To switch to the next slot, the VCD sends another EOF.
The following rules and restrictions apply:
●
if no LRI64 answer is detected, the VCD may switch to the next slot by sending an EOF
●
if one or more LRI64 answers are detected, the VCD waits until the complete frame has
been received before sending an EOF, to switch to the next slot.
The pulse shall be generated according to the definition of the EOF in ISO 15693 and ISO
18000-3 Mode 1 standards.
25/52
Anti-collision
LRI64
Figure 20. Comparison between the Mask, Slot Number and UID
MSB
LSB
0000 0100 1100 1111 b 16 bits
Mask value received in the Inventory command
MSB
LSB
100 1100 1111 b 11 bits
The Mask value less the padding 0s is loaded
into the Tag comparator
MSB LSB
xxxx
The Slot counter is calculated
Nb_slots_flags = 0 (16 slots), Slot Counter is 4 bits
The Slot counter is concatened to the Mask value
Nb_slots_flags = 0
The concatenated result is compared with
the least significant bits of the Tag UID.
4 bits
MSB
LSB
xxxx 100 1100 1111 b 15 bits
UID
b63
b0
xxxx xxxx ..... xxxx xxxx x xxx xxxx xxxx xxxx b
Bits ignored
64 bits
Compare
AI06682
26/52
LRI64
16
Request processing by the LRI64
Request processing by the LRI64
Upon reception of a valid Request, the LRI64 performs the following algorithm, where:
●
NbS is the total number of slots (1 or 16)
●
SN is the current slot number (0 to 15)
●
The function LSB(value,n) returns the n least significant bits of value
●
The function MSB(value,n) returns the n most significant bits of value
●
“&” is the concatenation operator
●
Slot_Frame is either a SOF or an EOF
SN = 0
if (Nb_slots_flag)
then NbS = 1
SN_length = 0
endif
else NbS = 16
SN_length = 4
endif
label1:
if LSB(UID, SN_length + Mask_length) =
LSB(SN,SN_length)&LSB(Mask,Mask_length)
then answer to inventory request
endif
wait (Slot_Frame)
if Slot_Frame = SOF
then Stop Anticollision
decode/process request
exit
endif
if Slot_Frame = EOF
if SN < NbS-1
then SN = SN + 1
goto label1
exit
endif
endif
27/52
Request processing by the LRI64
16.1
LRI64
Explanation of the possible cases
Figure 21 summarizes the main possible cases that can occur during an anti-collision
sequence when the number of slots is 16.
The different steps are:
Note:
28/52
●
The VCD sends an Inventory Request, in a frame, terminated by a EOF. The number of
slots is 16.
●
LRI64 #1 transmits its Response in Slot 0. It is the only one to do so, therefore no
collision occurs and its UID is received and registered by the VCD;
●
The VCD sends an EOF, to switch to the next slot.
●
In slot 1, two LRI64 devices, #2 and #3, transmit their Responses. This generates a
collision. The VCD records it, and remembers that a collision was detected in Slot 1.
●
The VCD sends an EOF, to switch to the next slot.
●
In Slot 2, no LRI64 transmits a Response. Therefore the VCD does not detect a LRI64
SOF, and decides to switch to the next slot by sending an EOF.
●
In slot 3, there is another collision caused by Responses from LRI64 #4 and #5
●
The VCD then decides to send a Request (for instance a Read Block) to LRI64 #1,
whose UID was already correctly received.
●
All LRI64 devices detect a SOF and exit the anti-collision sequence. They process this
Request and since the Request is addressed to LRI64 #1, only LRI64 #1 transmits its
Response.
●
All LRI64 devices are ready to receive another Request. If it is an Inventory command,
the slot numbering sequence restarts from 0.
The decision to interrupt the anti-collision sequence is up to the VCD. It could have
continued to send EOFs until Slot 15 and then send the Request to LRI64 #1.
Time
Comment
Timing
VICCs
VCD
SOF
Inventory
EOF
Request
t1
No
collision
Response
1
Slot 0
t2
EOF
t1
Collision
Response
3
Response
2
Slot 1
t2
EOF
No
Response
t3
Slot 2
EOF
t1
Collision
Response
5
Response
4
Slot 3
t2
SOF
Request to
EOF
LRI512 1
t1
AI06831B
Response
from
LRI512 1
LRI64
Request processing by the LRI64
Figure 21. Description of a possible anti-collision sequence between LRI64 devices
29/52
Timing definitions
17
LRI64
Timing definitions
Figure 21 shows three specific delay times: t1, t2 and t3. All of them have a minimum value,
specified in Table 14. The t1 parameter also has a maximum and a typical value specified in
Table 14, as summarized in Table 8.
Table 8.
Timing values(1)
Min.
Typ.
Max.
t1
t1(min)
t1(typ) = 4352 / fC
t1(max)
t2
t2(min) = 4192 / fC
—
—
t3
t1(max) + tSOF
(see notes(2),(3))
—
—
1. The tolerance of specific timings is ± 32/fC.
2. tSOF is the duration for the LRI64 to transmit an SOF to the VCD.
3. t1(max) does not apply for write alike requests. Timing conditions for write alike requests are defined in the
command description.
17.1
LRI64 response delay, t1
Upon detection of the rising edge of the EOF received from the VCD, the LRI64 waits for a
time equal to
t1(typ) = 4352 / fC
before starting to transmit its response to a VCD request, or switching to the next slot when
in an inventory process.
17.2
VCD new request delay, t2
t2 is the time after which the VCD may send an EOF to switch to the next slot when one or
more LRI64 responses have been received during an inventory command. It starts from the
reception of the EOF received from the LRI64 devices.
The EOF sent by the VCD is 10% modulated, independent of the modulation index used for
transmitting the VCD request to the LRI64.
t2 is also the time after which the VCD may send a new request to the LRI64 as described in
Figure 18.
t2(min) = 4192 / fC
30/52
LRI64
17.3
Timing definitions
VCD new request delay when there is no LRI64 response, t3
t3 is the time after which the VCD may send an EOF to switch to the next slot when no LRI64
response has been received.
The EOF sent by the VCD is 10% modulated, independent of the modulation index used for
transmitting the VCD request to the LRI64.
From the time the VCD has generated the rising edge of an EOF:
●
The VCD waits for a time at least equal to the sum of t3(min) and the typical response
time of an LRI64, which depends on the data rate and subcarrier modulation mode,
before sending a subsequent EOF.
31/52
Command codes
18
LRI64
Command codes
The LRI64 supports the command codes listed in Table 9.
Table 9.
18.1
Command codes
Command code
Function
01h
Inventory
02h
Stay Quiet
20h
Read Single Block
21h
Write Single Block
2Bh
Get System Info
Inventory
When receiving the Inventory request, the LRI64 performs the anti-collision sequence. The
Inventory_flag is set to 1. The meanings of Flags 5 to 8 is as described in Table 5.
The Request Frame (Figure 22) contains:
●
Request Flags (Table 3 and Table 5)
●
Inventory Command Code (01h, Table 9)
●
AFI, if the AFI Flag is set
●
Mask Length
●
Mask Value
●
2-byte CRC (Figure 15)
In case of errors in the Inventory request frame, the LRI64 does not generate any answer.
The Response Frame (Figure 23) contains:
●
Response Flags (Table 6)
●
DSFID
●
Unique ID
●
2-byte CRC (Figure 15)
Figure 22. Inventory, request frame format
Request
SOF
Request Command Optional
Flags
Code
AFI
8 bits
8 bits
01h
8 bits
Mask
Length
Mask Value
2-Byte
CRC
8 bits
0 to 8 bytes
16 bits
Request
EOF
AI09729
Figure 23. Inventory, response frame format
Response Response
SOF
Flags
8 bits
DSFID
UID
2-Byte
CRC
8 bits
64 bits
16 bits
Response
EOF
AI09730
32/52
LRI64
18.2
Command codes
Stay Quiet
The Stay Quiet Command is always executed in Addressed Mode (the Address_Flag is set
to 1).
The Request Frame (Figure 24) contains:
●
Request Flags (22h, as described in Table 3 and Table 4)
●
Stay Quiet Command Code (02h, Table 9)
●
Unique ID
●
2-byte CRC (Figure 15)
When receiving the Stay Quiet command, the LRI64 enters the Quiet State and does not
send back a Response. There is no response to the Stay Quiet Command.
When in the Quiet State:
●
the LRI64 does not process any Request in which the Inventory_flag is set
●
the LRI64 responds to commands in the Addressed mode if the UID matches
The LRI64 exits the Quiet State when it is taken to the Power Off state (Figure 19).
Figure 24. Stay Quiet, request frame format
Request
SOF
Request Command
Flags
Code
8 bits
22h
8 bits
02h
UID
2-Byte
CRC
64 bits
16 bits
Request
EOF
AI09731
Figure 25. Stay Quiet frame exchange between VCD and LRI64
VCD
SOF
Stay Quiet
Request
EOF
AI06842
33/52
Command codes
18.3
LRI64
Read Single Block
When receiving the Read Single Block Command, the LRI64 reads the requested block and
sends back its 8-bit value in the Response. The Option_Flag is supported. The Read Single
Block can be issued in both addressed and non addressed modes.
The Request Frame (Figure 26) contains:
●
Request Flags (Table 3 and Table 4)
●
Read Single Block Command Code (20h, Table 9)
●
Unique ID (Optional)
●
Block Number
●
2-byte CRC (Figure 15)
If there is no error, at the LRI64, the Response Frame (Figure 27) contains:
●
Response Flags (Table 6)
●
Block Locking Status, if Option_Flag is set
●
1 byte of Block Data (Table 10)
●
2-byte CRC (Figure 15)
Otherwise, if there is an error, the Response Frame (Figure 28) contains:
●
Response Flags (01h, Table 6)
●
Error Code (0Fh, Table 7)
●
2-byte CRC (Figure 15)
Table 10.
Block lock status
Bit
0
1 to 7
Name
Value
Description
0
Current Block not locked
1
Current Block locked
Block Locked
RFU
0
Figure 26. Read Single Block, request frame format
Request
SOF
Request Command
Flags
Code
8 bits
UID
8 bits
20h
Block
Number
2-Byte
CRC
8 bits
16 bits
64 bits
Request
EOF
AI09732
Figure 27. Read Single Block, response frame format, when Error_Flag is not set
Response Response BlockLock
SOF
Flags
Status
Data
2-Byte
CRC
8 bits
8 bits
16 bits
8 bits
Response
EOF
AI09733
Figure 28. Read Single Block, response frame format, when Error_Flag is set
Response Response
SOF
Flags
8 bits
01h
34/52
Error
Code
2-Byte
CRC
8 bits
0Fh
16 bits
Response
EOF
AI09734
LRI64
Command codes
Figure 29. READ Single Block frame exchange between VCD and LRI64
VCD
SOF
Read Single
Block Request
EOF
VICC
SOF
t1
Read Single
Block Response
EOF
AI06832B
18.4
Write Single Block
When receiving the Write Single Block command, the LRI64 writes the requested block with
the data contained in the Request and report the success of the operation in the Response.
The Option_Flag is not supported and must be set to 0. The Write Single Block can be
issued in both addressed and non addressed modes.
During the write cycle tW, no modulation shall occur, otherwise the LRI64 may program the
data incorrectly in the memory.
The Request Frame (Figure 30) contains:
●
Request Flags (Table 3 and Table 4)
●
Write Single Block Command Code (21h, Table 9)
●
Unique ID (Optional)
●
Block Number
●
Data
●
2-byte CRC (Figure 15)
If there is no error, at the LRI64, an empty Response Frame (Figure 31) is sent back after
the write cycle, containing no parameters. It just contains:
●
Response Flags (Table 6)
●
2-byte CRC (Figure 15)
Otherwise, if there is an error, the Response Frame (Figure 32) contains:
●
Response Flags (01h, Table 6)
●
Error Code (0Fh, Table 7)
●
2-byte CRC (Figure 15)
Figure 30. Write Single Block, request frame format
Request
SOF
Request Command
Flags
Code
8 bits
8 bits
21h
UID
64 bits
Block
Number
Data
2-Byte
CRC
8 bits
8 bits
16 bits
Request
EOF
AI09735
Figure 31. Write Single Block, response frame format, when Error_Flag is not set
Response Response
SOF
Flags
8 bits
2-Byte
CRC
Response
EOF
16 bits
AI09736
35/52
Command codes
LRI64
Figure 32. Write Single Block, response frame format, when Error_Flag is set
Response Response
SOF
Flags
8 bit
01h
Error
Code
2-Byte
CRC
8 bits
0Fh
16 bits
Response
EOF
AI09737
Figure 33. Write Single Block frame exchange between VCD and LRI64
VCD
SOF
Write Single
Block Request
EOF
SOF
VICC
t1
Write Single
Block Response
VICC
EOF
SOF
tw
t1
Write sequence when error
Write Single
Block Response
EOF
AI06833B
36/52
LRI64
18.5
Command codes
Get System Info
When receiving the Get System Info command, the LRI64 send back its information data in
the Response.The Option_Flag is not supported and must be set to 0. The Get System Info
can be issued in both addressed and non addressed modes.
The Request Frame (Figure 26) contains:
●
Request Flags (Table 3 and Table 4)
●
Get System Info Command Code (2Bh, Table 9)
●
Unique ID (Optional)
●
2-byte CRC (Figure 15)
If there is no error, at the LRI64, the Response Frame (Figure 27) contains:
●
Response Flags (Table 6)
●
Information Flags set to 0Fh, indicating the four information fields that are present
(DSFID, AFI, Memory Size, IC Reference)
●
Unique ID
●
DSFID value (as written in block 9)
●
AFI value (as written in block 8)
●
Memory size: for the LRI64, there are 15 blocks (0Eh) of 1 byte (00h).
●
IC Reference: only the 6 most significant bits are used. The product code of the LRI64
is 00 0101b=5d
●
2-byte CRC (Figure 15)
Otherwise, if there is an error, the Response Frame (Figure 28) contains:
●
Response Flags (01h, Table 6)
●
Error Code (0Fh, Table 7)
●
2-byte CRC (Figure 15)
Figure 34. Get System Info, request frame format
Request
SOF
Request Command
Flags
Code
8 bits
8 bits
2Bh
UID
2-Byte
CRC
64 bits
16 bits
Request
EOF
AI09738
Figure 35. Get System Info, response frame format, when Error_Flag is not set
Response Response Information
SOF
Flags
Flags
8 bits
00h
8 bits
0Fh
UID
DSFID
AFI
Memory
Size
IC
Ref
64 bits
8 bits
8 bits
16 bits
000Eh
8 bits
000101xxb
2-Byte Response
CRC
EOF
16 bits
AI09739
Figure 36. Get System Info, response frame format, when Error_Flag is set
Response Response
SOF
Flags
8 bits
01h
Error
Code
2-Byte
CRC
8 bits
0Fh
16 bits
Response
EOF
AI09740
37/52
Command codes
LRI64
Figure 37. Get System Info frame exchange between VCD and LRI64
VCD
SOF
Get System
Info Request
EOF
VICC
SOF
t1
Get System
Info Response
EOF
AI09724
38/52
LRI64
19
Maximum rating
Maximum rating
Stressing the device above the rating listed in the Absolute Maximum Ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 11.
Absolute maximum ratings
Symbol
Parameter
Min.
Max.
Unit
15
25
°C
23
months
Wafer
kept in its antistatic bag
TSTG, hSTG,
Storage Conditions
tSTG
A1, A6, A7
ICC
VMAX
VESD
15
25
°C
40%
60%
RH
2
years
Supply Current on AC0 / AC1
–20
20
mA
Input Voltage on AC0 / AC1
–7
7
V
–7000
7000
V
Electrostatic Discharge
(2)
Voltage(1)
A1, A6, A7
1. Mil. Std. 883 - Method 3015
2. ESD test: ISO10373-7 specification
39/52
DC and AC parameters
20
LRI64
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC Characteristic tables that
follow are derived from tests performed under the Measurement Conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 12.
Operating conditions
Symbol
TA
Parameter
Ambient operating temperature
Min.
Max.
Unit
–20
85
°C
Figure 38. LRI64 synchronous timing, transmit and receive
A
B
tRFF
tRFR
fCC
tRFSBL
tMIN CD
AI06680B
Figure 38 shows an ASK modulated signal, from the VCD to the LRI64. The test condition
for the AC/DC parameters are:
●
Close coupling condition with tester antenna (1mm)
●
Gives LRI64 performance on tag antenna
Table 13.
DC characteristics
Symbol
Min.
Typ.
Unit
3.0
V
Regulated Voltage
VRET
Retromodulated Induced Voltage
ISO10373-7
Read
VCC = 3.0 V
50
µA
Write
VCC = 3.0 V
150
µA
CTUN
1.5
Max.
VCC
ICC
Supply Current
Internal Tuning Capacitor
1. TA = –20 to 85 °C
40/52
Test conditions(1)
Parameter
10
mV
f=13.56 MHz for W4/1
21
pF
f=13.56 MHz for W4/2
28.5
pF
f=13.56 MHz for W4/3
97
pF
LRI64
DC and AC parameters
Table 14.
AC characteristics
Symbol
Parameter
fC
External RF Signal Frequency
Test
conditions(1),(2)
Min.
Typ.
Max.
Unit
13.553
13.56
13.567
MHz
10
30
%
0
3.0
µs
10% Minimum Pulse Width for
Bit
7.1
9.44
µs
Bit Pulse Jitter
–2
+2
µs
1
ms
MICARRIER 10% Carrier Modulation Index
MI=(A-B)/(A+B)
tRFR, tRFF 10% Rise and Fall Time
tRFSBL
tJIT
tMINCD
Minimum Time from Carrier
Generation to First Data
From H-field min
0.1
fSH
Subcarrier Frequency High
fC/32
423.75
t1
Time for LRI64 Response
4352/fC
313
320.9
322
µs
t2
Time between Commands
4224/fC
309
311.5
314
µs
tW
Programming Time
93297/fC
6.88
ms
kHz
1. TA = –20 to 85 °C
2. All timing measurements were performed on a reference antenna with the following characteristics:
External size: 75mm x 48mm
Number of turns: 6
Width of conductor: 1mm
Space between 2 conductors: 0.4mm
Value of the Tuning Capacitor: 28.5pF (LRI64-W4)
Value of the coil: 4.3µH
Tuning Frequency: 14.4MHz.
41/52
Package mechanical
21
LRI64
Package mechanical
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second-level interconnect. The category of
Second-Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97.
The maximum ratings related to soldering conditions are also marked on the inner box label.
ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
Figure 39. A1 Antenna on tape outline
C1
A1
B1
C2
A2
B2
ai10119
1. Drawing is not to scale.
Table 15.
A1 Antenna on tape mechanical data
Symbol
Typ
Min
Max
Unit
A1
Coil Width
45
44.5
45.5
mm
A2
Coil Length
76
75.5
76.5
mm
B1
Antenna Cut Width
49
48.8
49.2
mm
B2
Antenna Cut Length
82
81.8
82.2
mm
C1
Die Position from Antenna
23
22.8
23.2
mm
C2
Die Position from Antenna
56
55.8
56.2
mm
Silicon Thickness
180
165
195
µm
Unloaded Q value
35
Q
FNOM
PA
42/52
Parameter
Unloaded free-air resonance
H-field Energy for Device Operation
15.1
MHz
0.03
90
A/m
dbµA/m
LRI64
Package mechanical
Figure 40. A6 Antenna on tape outline
I
A
B
ai10120
1. Drawing is not to scale.
Table 16.
A6 Antenna on tape mechanical data
Symbol
Parameter
Typ
Min
Max
Unit
A
Coil Diameter
35
34.5
35.5
mm
B
Antenna cut diameter
40
38.8
40.2
mm
I
Hole Diameter
16
15.8
16.2
mm
Overall Thickness of copper antenna coil
80
70
90
µm
Silicon Thickness
180
165
195
µm
Unloaded Q value
35
Q
FNOM
PA
Unloaded free-air resonance
H-field Energy for Device Operation
15.1
MHz
0.5
114
A/m
dbµA/m
43/52
Package mechanical
LRI64
Figure 41. A7 Antenna on tape outline
A1
B1
C1
C2
A2
B2
ai10121
1. Drawing is not to scale.
Table 17.
A7 Antenna on tape mechanical data
Symbol
Typ
Min
Max
Unit
A1
Coil Width
40
39.5
40.5
mm
A2
Coil Length
20
19.5
20.5
mm
B1
Antenna Cut Width
44
43.8
44.2
mm
B2
Antenna Cut Length
24
23.8
24.2
mm
C1
Die Position from Antenna
10
9.8
10.2
mm
C2
Die Position from Antenna
20
19.8
20.2
mm
Overall Thickness of copper antenna coil
160
145
175
µm
Silicon Thickness
180
165
195
µm
Unloaded Q value
35
Q
FNOM
PA
44/52
Parameter
Unloaded free-air resonance
H-field Energy for Device Operation
15.1
MHz
1
120
A/m
dbµA/m
LRI64
Package mechanical
Figure 42. 8-lead Ultra thin Fine pitch Dual Flat Package No lead (MLP) outline
e
D
b
L1
L3
E
E2
L
A
D2
ddd
A1
UFDFPN-01
1. Drawing is not to scale.
Table 18.
UFDFPN8 (MLP8), 8-lead Ultra thin Fine pitch Dual Flat Package No lead
2 × 3 mm, package mechanical data
millimeters
inches
Symbol
Typ
Min
Max
Typ
Min
Max
A
0.55
0.50
0.60
0.022
0.020
0.024
A1
0.02
0.00
0.05
0.001
0.000
0.002
b
0.25
0.20
0.30
0.010
0.008
0.012
D
2.00
1.90
2.10
0.079
0.075
0.083
D2
1.60
1.50
1.70
0.063
0.059
0.067
ddd
0.08
0.003
E
3.00
2.90
3.10
0.118
0.114
0.122
E2
0.20
0.10
0.30
0.008
0.004
0.012
e
0.50
–
–
0.020
–
–
L
0.45
0.40
0.50
0.018
0.016
0.020
L1
L3
0.15
0.30
0.006
0.012
45/52
Part numbering
22
LRI64
Part numbering
Table 19.
Ordering information scheme
Example:
LRI64
–
W4
/XXX
Device type
LRI64
Package
W4 =180 µm ± 15 µm Unsawn Wafer, 18.5 pF tuning capacitor
SBN18 = 180 µm ± 15 µm Bumped and Sawn Wafer on 8-inch Frame
A1T = 45 mm × 76 mm Copper Antenna on Continuous Tape
A1S = 45 mm × 76 mm Copper Singulated Adhesive Antenna on Tape
A6S2U = 35 mm Copper Singulated Adhesive CD Antenna on white PET Tape and no
marking
A7T = 20 mm × 40 mm Copper Antenna on Continuous Tape
MBTG = UDFDFPN8 (MLP8), Tape & Reel Packing, ECOPACK® and RoHS
compliant, Sb2O3-free and TBBA-free(1)
Customer code
XXX = Given by STMicroelectronics
1. The category of second Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are
also marked on the inner box label.
For a list of available options (speed, package, etc.) or for further information on any aspect
of this device, please contact your nearest ST Sales Office.
46/52
LRI64
algorithm for pulsed slots
Appendix A
algorithm for pulsed slots
The following pseudo-code describes how the anti-collision could be implemented on the
VCD, using recursive functions.
function
function
function
function
push (mask, address); pushes on private stack
pop (mask, address); pops from private stack
pulse_next_pause; generates a power pulse
store(LRI64_UID); stores LRI64_UID
function poll_loop (sub_address_size as integer)
pop (mask, address)
mask = address & mask; generates new mask
; send the Request
mode = anti-collision
send_Request (Request_cmd, mode, mask length, mask value)
for sub_address = 0 to (2^sub_address_size - 1)
pulse_next_pause
if no_collision_is_detected ; LRI64 is inventoried
then
store (LRI64_UID)
else ; remember a collision was detected
push(mask,address)
endif
next sub_address
if stack_not_empty ; if some collisions have been detected and
then
; not yet processed, the function calls itself
poll_loop (sub_address_size); recursively to process the
last stored collision
endif
end poll_loop
main_cycle:
mask = null
address = null
push (mask, address)
poll_loop(sub_address_size)
end_main_cycle
47/52
C-example to calculate or check the CRC16 according to ISO/IEC 13239
Appendix B
LRI64
C-example to calculate or check the CRC16
according to ISO/IEC 13239
The Cyclic Redundancy Check (CRC) is calculated on all data contained in a message,
from the start of the Flags through to the end of Data. This CRC is used from VCD to LRI64
and from LRI64 to VCD.
To add extra protection against shifting errors, a further transformation on the calculated
CRC is made. The One’s Complement of the calculated CRC is the value attached to the
message for transmission.
For checking of received messages the 2 CRC bytes are often also included in the recalculation, for ease of use. In this case, given the expected value for the generated CRC is
the residue of F0B8h
Table 20.
CRC definition
CRC definition
22.1
CRC Type
Length
ISO/IEC
13239
16 bits
Polynomial
X16 + X12 + X5 + 1
= Ox8408
Direction
Preset
Residue
Backward
FFFFh
F0B8h
CRC calculation example
This example in C language illustrates one method of calculating the CRC on a given set of
bytes comprising a message.
#define
#define
#define
POLYNOMIAL0x8408//
PRESET_VALUE0xFFFF
CHECK_VALUE0xF0B8
x^16 + x^12 + x^5 + 1
#define
#define
#define
NUMBER_OF_BYTES4// Example: 4 data bytes
CALC_CRC1
CHECK_CRC0
void main()
{
unsigned int current_crc_value;
unsigned char array_of_databytes[NUMBER_OF_BYTES + 2] = {1, 2, 3,
4, 0x91, 0x39};
int
number_of_databytes = NUMBER_OF_BYTES;
int
calculate_or_check_crc;
int
i, j;
calculate_or_check_crc = CALC_CRC;
// calculate_or_check_crc = CHECK_CRC;// This could be an other
example
if (calculate_or_check_crc == CALC_CRC)
{
number_of_databytes = NUMBER_OF_BYTES;
}
48/52
LRI64
C-example to calculate or check the CRC16 according to ISO/IEC 13239
else
// check CRC
{
number_of_databytes = NUMBER_OF_BYTES + 2;
}
current_crc_value = PRESET_VALUE;
for (i = 0; i < number_of_databytes; i++)
{
current_crc_value = current_crc_value ^ ((unsigned
int)array_of_databytes[i]);
for (j = 0; j < 8; j++)
{
if (current_crc_value & 0x0001)
{
current_crc_value = (current_crc_value >> 1) ^
POLYNOMIAL;
}
else
{
current_crc_value = (current_crc_value >> 1);
}
}
}
if (calculate_or_check_crc == CALC_CRC)
{
current_crc_value = ~current_crc_value;
printf ("Generated CRC is 0x%04X\n", current_crc_value);
//
stream
//
}
else
{
if
{
current_crc_value is now ready to be appended to the data
(first LSByte, then MSByte)
// check CRC
(current_crc_value == CHECK_VALUE)
printf ("Checked CRC is ok (0x%04X)\n",
current_crc_value);
}
else
{
printf ("Checked CRC is NOT ok (0x%04X)\n",
current_crc_value);
}
}
}
49/52
Application family identifier (AFI) coding
Appendix C
LRI64
Application family identifier (AFI) coding
AFI (Application Family Identifier) represents the type of application targeted by the VCD
and is used to extract from all the LRI64 present only the LRI64 meeting the required
application criteria.
It is programmed by the LRI64 issuer (the purchaser of the LRI64). Once locked, it can not
be modified.
The most significant nibble of AFI is used to code one specific or all application families, as
defined in Table 21.
The least significant nibble of AFI is used to code one specific or all application sub-families.
Sub-family codes different from 0 are proprietary.
Table 21.
AFI coding(1)
AFI
AFI
Most
Significant
Nibble
Least
Significant
Nibble
0
0
All families and sub-families
No applicative preselection
x
0
All sub-families of family X
Wide applicative preselection
x
y
Only the Yth sub-family of family X
0
y
Proprietary sub-family Y only
1
0, y
Transport
Mass transit, Bus, Airline,...
2
0, y
Financial
IEP, Banking, Retail,...
3
0, y
Identification
Access Control,...
4
0, y
Telecommunication
Public Telephony, GSM,...
5
0, y
Medical
6
0, y
Multimedia
7
0, y
Gaming
8
0, y
Data Storage
9
0, y
Item Management
A
0, y
Express Parcels
B
0, y
Postal Services
C
0, y
Airline Bags
D
0, y
RFU
E
0, y
RFU
F
0, y
RFU
Meaning
Examples / Note
LRI64 Devices respond from
Internet services....
Portable Files...
1. x and y each represent any single-digit hexadecimal value between 1 and F
50/52
LRI64
Revision history
Revision history
Table 22.
Document revision history
Date
Revision
27-Aug-2003
1.0
First Issue
16-Jul-2004
2.0
First public release of full datasheet
22-Sep-2004
3.0
Values changed for tW, t1 and t2
11-Jul-2005
4.0
Added MLP package information.
7-Sept-2005
5.0
Modified Option_Flag information in Get System Info command and
added ISO 18000-3 Mode 1 compliance.
19-Feb-2007
6
Changes
Document reformatted. UFDPFN8 package specifications updated (see
Table 18: UFDFPN8 (MLP8), 8-lead Ultra thin Fine pitch Dual Flat
Package No lead 2 × 3 mm, package mechanical data). ST offers the
LRI64 in ECOPACK® compliant UFDPFN8 packages.
CTUN value for W4/3 added to Table 13: DC characteristics.
Small text changes.
51/52
LRI64
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
52/52