M54HC157 RAD-HARD QUAD 2 CHANNEL MULTIPLEXER ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 10ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 157 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9408-057 DESCRIPTION The M54HC157 is an high speed CMOS QUAD 2 CHANNEL MULTIPLEXER fabricated with silicon gate C2MOS technology. DILC-16 FPC-16 ORDER CODES PACKAGE FM EM DILC FPC M54HC157D M54HC157K M54HC157D1 M54HC157K1 These device consist of four 2-input digital multiplexer with common select and strobe inputs. When the STROBE input is held high, selection of data is inhibited and all the outputs become low. The SELECT decoding determines whether the A or B inputs get routed to their corresponding Y outputs. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION June 2004 Rev. 1 1/9 M54HC157 Figure 1: IEC Logic Symbols Figure 2: Input And Output Equivalent Circuit Table 1: Pin Description PIN N° SYMBOL 1 SELECT 2, 5, 11, 14 1A to 4A Common Data Select Input Data Inputs From NAME AND FUNCTION 3, 6, 10, 13 1B to 4B Source A Data Inputs From 4, 7, 9, 12 15 8 16 1Y to 4Y STROBE GND VCC Source B Multiplexer Output Strobe Inputs Ground (0V) Positive Supply Voltage Table 2: Truth Table INPUTS STROBE SELECT A B Y H L L L L X L L H H X L H X X X X X L H L L H L H X : Don’t Care 2/9 OUTPUTS M54HC157 Figure 3: Logic Diagram Table 3: Absolute Maximum Ratings Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage -0.5 to VCC + 0.5 ± 20 V mA IIK DC Input Diode Current IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) ± 50 mA 300 mW -65 to +150 °C 265 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 4: Recommended Operating Conditions Symbol VCC Parameter Supply Voltage Value Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature Input Rise and Fall Time tr, tf -55 to 125 °C VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns 3/9 M54HC157 Table 5: DC Specifications Test Condition Symbol VIH VIL VOH VOL II ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 Unit V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-4.0 mA 4.18 4.31 4.13 4.10 6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 V V 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=4.0 mA 0.17 0.26 0.33 0.40 6.0 IO=5.2 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VCC or GND 4 40 80 µA V * : Applicable only to DIR, G, G input Table 6: AC Electrical Characteristics (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (A, B - Y) tPLH tPHL Propagation Delay Time (SELECT - Y) tPLH tPHL Propagation Delay Time (STROBE -Y) 4/9 VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value TA = 25°C Min. Typ. Max. 30 8 7 30 12 10 50 16 14 36 12 10 75 15 13 100 20 17 125 25 21 115 23 20 -40 to 85°C -55 to 125°C Min. Min. Max. 95 19 16 125 25 21 155 31 26 145 29 25 Unit Max. 110 22 19 150 30 26 190 38 32 175 35 30 ns ns ns ns M54HC157 Table 7: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 5.0 5 CPD Power Dissipation Capacitance (note 1) 5.0 47 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4(per channel) Figure 4: Test Circuit CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) Figure 5: Waveform - Propagation Delay Times (f=1MHz; 50% duty cycle) 5/9 M54HC157 DILC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.1 2.71 0.083 0.107 a1 3.00 3.70 0.118 0.146 a2 0.63 1.14 0.025 B 1.82 2.39 0.072 b 0.40 0.45 0.50 0.016 0.018 0.020 b1 0.20 0.254 0.30 0.008 0.010 0.012 D 20.06 20.32 20.58 0.790 0.800 0.810 E 7.36 7.62 7.87 0.290 0.300 0.310 e 0.88 2.54 0.035 0.045 0.094 0.100 e1 17.65 17.78 17.90 0.695 0.700 0.705 e2 7.62 7.87 8.12 0.300 0.310 0.320 F 7.29 7.49 7.70 0.287 0.295 0.303 I 3.83 0.151 K 10.90 12.1 0.429 0.476 L 1.14 1.5 0.045 0.059 0056437F 6/9 M54HC157 FPC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 6.75 6.91 7.06 0.266 0.272 0.278 B 9.76 9.94 10.14 0.384 0.392 0.399 C 1.49 1.95 0.059 D 0.102 0.127 0.152 0.004 0.005 0.006 E 8.76 8.89 9.01 0.345 0.350 0.355 F 0.077 1.27 G 0.38 H 6.0 L 18.75 M 0.33 0.050 0.43 0.48 0.015 0.017 0.019 0.237 0.38 N 22.0 0.738 0.43 0.013 0.867 0.015 4.31 0.017 0.170 G F D H 9 16 A N L 8 1 H E B M C 0016030E 7/9 M54HC157 Table 8: Revision History 8/9 Date Revision 01-Jun-2004 1 Description of Changes First Release M54HC157 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 9/9