TI TPS77101DGK

TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
D Open Drain Power-On Reset With 220-ms
D
D
D
D
D
D
D
D
D
D
TPS771xx
DGK Package
(TOP VIEW)
Delay (TPS771xx)
Open Drain Power-Good (PG) Status
Output (TPS772xx)
150-mA Low-Dropout Voltage Regulator
Available in 1.5-V, 1.8-V, 2.7-V, 2.8-V, 3.3-V,
5.0-V Fixed Output and Adjustable Versions
Dropout Voltage Typically 115 mV
at 150 mA (TPS77133, TPS77233)
Ultralow 92-µA Quiescent Current (Typ)
8-Pin MSOP (DGK) Package
Low Noise (55 µVrms) Without External
Filter (Bypass) Capacitor (TPS77118,
TPS77218)
2% Tolerance Over Specified Conditions
for Fixed-Output Versions
Fast Transient Response
Thermal Shutdown Protection
FB/SENSE
RESET
EN
GND
1
8
2
7
3
6
4
5
OUT
OUT
IN
IN
TPS772xx
DGK Package
(TOP VIEW)
FB/SENSE
PG
EN
GND
1
8
2
7
3
6
4
5
OUT
OUT
IN
IN
TPS77x33
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
300
description
250
VDO – Dropout Voltage – mV
The TPS771xx and TPS772xx are low-dropout
regulators with integrated power-on reset and
power good (PG) function respectively. These
devices are capable of supplying 150 mA of output
current with a dropout of 115 mV (TPS77133,
TPS77233). Quiescent current is 92 µA at full load
dropping down to 1 µA when device is disabled.
These devices are optimized to be stable with a
wide range of output capacitors including low ESR
ceramic (10 µF) or low capacitance (1 µF)
tantalum capacitors. These devices have extremely low noise output performance (55 µVrms)
without using any added filter capacitors.
TPS771xx and TPS772xx are designed to have
fast transient response for larger load current
changes.
200
IO = 150 mA
150
100
IO = 10 mA
50
IO = 0 A
0
–50
–40
0
40
80
120
TJ – Junction Temperature – °C
160
The TPS771xx or TPS772xx is offered in 1.5 V,
1.8-V, 2.7-V, 2.8-V, 3.3-V, and 5.0 V fixed-voltage versions and in an adjustable version (programmable over
the range of 1.5 V to 5.5 V). Output voltage tolerance is 2% over line, load, and temperature ranges. The
TPS771xx and TPS772xx families are available in 8-pin MSOP (DGK) packages.
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 115 mV
at an output current of 150 mA for 3.3 volt option) and is directly proportional to the output current. Additionally,
since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent
of output loading (typically 92 µA over the full range of output current, 0 mA to 150 mA). These two key
specifications yield a significant improvement in operating life for battery-powered systems.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
description (continued)
The device is enabled when the EN pin is connected to a low-level input voltage. This LDO family also features
a sleep mode; applying a TTL high signal to EN (enable) shuts down the regulator, reducing the quiescent
current to less than 1 µA at TJ = 25°C.
The TPS771xx features an integrated power-on reset, commonly used as a supply voltage supervisor (SVS)
or reset output voltage. The RESET output of the TPS771xx initiates a reset in DSP, microcomputer or
microprocessor systems at power up and in the event of an undervoltage condition. An internal comparator in
the TPS771xx monitors the output voltage of the regulator to detect an undervoltage condition on the regulated
output voltage. When OUT reaches 95% of its regulated voltage, RESET will go to a high-impedance state after
a 220 ms delay. RESET will go to low-impedance state when OUT is pulled below 95% (i.e. over load condition)
of its regulated voltage.
For the TPS772xx, the power good terminal (PG) is an active high output, which can be used to implement a
power-on reset or a low-battery indicator. An internal comparator in the TPS772xx monitors the output voltage
of the regulator to detect an undervoltage condition on the regulated output voltage. When OUT falls below 82%
of its regulated voltage, PG will go to a low-impedance state. PG will go to a high-impedance state when OUT
is above 82% of its regulated voltage.
AVAILABLE OPTIONS
OUTPUT VOLTAGE
(V)
PACKAGED DEVICES
MSOP (DGK)
TJ
TPS771xx
SYMBOL
TYP
TPS772xx
SYMBOL
5.0
TPS77150DGK
AFV
TPS77250DGK
AGE
3.3
TPS77133DGK
AFU
TPS77233DGK
AGD
2.8
TPS77128DGK
AFS
TPS77228DGK
AGB
2.7
TPS77127DGK
AFR
TPS77227DGK
AGA
1.8
TPS77118DGK
AFP
TPS77218DGK
AFY
1.5
TPS77115DGK
AFO
TPS77215DGK
AFX
Adjustable
1.5 V to 5.5 V
TPS77101DGK
AFN
TPS77201DGK
AFW
– 40°C to 125°C
NOTE: The TPS77101 and TPS77201 are programmable using an external resistor divider (see application information).
The DGK package is available taped and reeled. Add an R suffix to the device type (e.g., TPS77101DGKR).
VI
5
IN
OUT
6
OUT
IN
SENSE
0.1 µF
3
PG or
RESET
EN
7
VO
8
1
2
GND
PG or RESET
+
10 µF
4
Figure 1. Typical Application Configuration (For Fixed Output Options)
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
functional block diagrams
adjustable version
IN
EN
PG or RESET
_
+
OUT
+
_
220 ms Delay
(for TPS771xx Option)
Vref = 1.1834 V
R1
FB/SENSE
R2
GND
External to the Device
fixed-voltage version
IN
EN
PG or RESET
_
+
OUT
+
_
220 ms Delay
(for TPS771xx Option)
SENSE
R1
Vref = 1.1834 V
R2
GND
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
TPS771XX
FB/SENSE
1
I
Feedback input voltage for adjustable device (sense input for fixed options)
RESET
2
O
Reset output
EN
3
I
Enable input
GND
4
Regulator ground
IN
5, 6
I
Input voltage
OUT
7, 8
O
Regulated output voltage
FB/SENSE
1
I
Feedback input voltage for adjustable device (sense input for fixed options)
PG
2
O
Power good
EN
3
I
Enable input
TPS772XX
GND
4
Regulator ground
IN
5, 6
I
Input voltage
OUT
7, 8
O
Regulated output voltage
TPS771xx RESET timing diagram
VI
Vres†
Vres†
t
VO
VIT +‡
VIT +‡
Threshold
Voltage
VIT –‡
VIT –‡
t
RESET
Output
Output
Undefined
ÎÎ
ÎÎ
ÎÎ
ÎÎ
220 ms
Delay
220 ms
Delay
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Output
Undefined
t
† Vres is the minimum input voltage for a valid RESET. The symbol Vres is not currently listed within EIA or JEDEC standards for
semiconductor symbology.
‡ VIT – Trip voltage is typically 5% lower than the output voltage (95%VO) VIT– to VIT+ is the hysteresis voltage.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TPS772xx PG timing diagram
VI
Vres†
Vres†
t
VO
VIT +‡
VIT +‡
Threshold
Voltage
VIT –‡
VIT –‡
t
PG
Output
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Output
Undefined
Output
Undefined
t
† Vres is the minimum input voltage for a valid PG. The symbol Vres is not currently listed within EIA or JEDEC standards for semiconductor
symbology.
‡ VIT – Trip voltage is typically 18% lower than the output voltage (82%VO) VIT– to VIT+ is the hysteresis voltage.
absolute maximum ratings over operating junction temperature range (unless otherwise noted)Ĕ
Input voltage range, VI, (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 13.5 V
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 16.5 V
Maximum RESET voltage (TPS771xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Maximum PG voltage (TPS772xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Output voltage, VO (OUT, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to network terminal ground.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
DISSIPATION RATING TABLE – FREE-AIR TEMPERATURES
PACKAGE
AIR FLOW
(CFM)
θJA
(°C/W)
θJC
(°C/W)
TA < 25°C
POWER RATING
0
266.2
3.84
DGK
150
255.2
3.92
250
242.8
4.21
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
376 mW
3.76 mW/°C
207 mW
150 mW
392 mW
3.92 mW/°C
216 mW
157 mW
412 mW
4.12 mW/°C
227 mW
165 mW
recommended operating conditions
MIN
Input voltage, VI†
Output voltage range, VO
Output current, IO (see Note 2)
MAX
UNIT
2.7
10
V
1.5
5.5
V
0
150
mA
Operating virtual junction temperature, TJ (see Note 2)
– 40
125
°C
† To calculate the minimum input voltage for your maximum output current, use the following equation: VI(min) = VO(max) + VDO(max load).
NOTE 2: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
electrical characteristics over recommended operating junction temperature range (–40°C to
125°C), VI = VO(typ) + 1 V, IO = 1 mA, EN = 0 V, CO = 10 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
1.5 V ≤ VO ≤ 5.5 V,
Adjustable voltage
Out ut voltage
Output
(see Notes 3 and 4)
MIN
TJ = 25°C
1.5 V ≤ VO ≤ 5.5 V
TJ = 25°C,
2.7 V < VIN < 10 V
2.7 V < VIN < 10 V
1 8 V Output
1.8-V
TJ = 25°C,
2.8 V < VIN < 10 V
2.8 V < VIN < 10 V
2 7 V Output
2.7-V
TJ = 25°C,
3.7 V < VIN < 10 V
3.7 V < VIN < 10 V
2 8 V Output
2.8-V
TJ = 25°C,
3.8 V < VIN < 10 V
3.8 V < VIN < 10 V
3 3 V Output
3.3-V
TJ = 25°C,
4.3 V < VIN < 10 V
4.3 V < VIN < 10 V
5 0 V Output
5.0-V
TJ = 25°C,
6 V < VIN < 10 V
6 V < VIN < 10 V
1.02VO
1.470
1.530
1.764
1.836
2.7
2.646
2.754
Output current Limit
2.856
3.3
3.234
3.366
5.0
4.900
5.100
92
VO + 1 V < VI ≤ 10 V, TJ = 25°C
VO + 1 V < VI ≤ 10 V
VO = 0 V
2 ms pulse width,
Peak output current
0.005
EN = VI,
TJ = 25°C
EN = VI
Adjustable voltage
FB = 1.5 V
High level enable input voltage
Enable input current
–1
Power supply ripple rejection (TPS77118, TPS77218)
%/V
mV
55
µVrms
1.3
A
400
mA
144
°C
1
µA
3
µA
1
µA
2
Low level enable input voltage
µA
A
1
0.9
50% duty cycle
V
%/V
0.05
Thermal shutdown junction temperature
Standby current
V
2.8
2.744
TJ = 25°C
BW = 300 Hz to 100 kHz, TJ = 25°C,
TPS77118, TPS77218
Output noise voltage
V
1.8
125
Load regulation
UNIT
1.5
TJ = 25°C
Output voltage line regulation (∆VO/VO) (see Note 5)
FB input current
MAX
VO
0.98VO
1 5 V Output
1.5-V
Quiescent current (GND current) (see Notes 3 and 4)
TYP
V
0.7
V
1
µA
TJ = 25°C
55
dB
NOTES: 3. Minimum input operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum input voltage = 10 V, minimum output
current 1 mA.
4. If VO < 1.8 V then VI(max) = 10 V, VI(min) = 2.7 V:
Line regulation (mV) + ǒ%ńVǓ
f = 1 KHz,
V
O
ǒVI(max) * 2.7 VǓ
100
1000
If VO > 2.5 V then VI(max) = 10 V, VI(min) = Vo + 1 V:
Line regulation (mV) + ǒ%ńVǓ
V
O
ǒVI(max) * ǒVO ) 1ǓǓ
100
1000
5. IO = 1 mA to 150 mA
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
electrical characteristics over recommended operating junction temperature range (–40°C to
125°C), VI = VO(typ) + 1 V, IO = 1 mA, EN = 0 V, CO = 10 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
Minimum input voltage for valid PG
PG
(TPS772xx)
Trip threshold voltage
I(PG) = 300µA
VO decreasing
Hysteresis voltage
Measured at VO
Output low voltage
VI = 2.7 V,
V(PG) = 5 V
Leakage current
Reset
(TPS771xx)
V(PG) ≤ 0.8 V
UNIT
85
%VO
%VO
1.1
I(PG) = 1mA
V
Hysteresis voltage
Measured at VO
Output low voltage
VI = 2.7 V,
V(RESET) = 5 V
0.15
0.4
V
1
µA
1.1
92
V
98
%VO
%VO
0.5
I(RESET) = 1 mA
RESET time-out delay
VDO
MAX
0.5
Trip threshold voltage
Leakage current
TYP
79
I(RESET) = 300 µA
VO decreasing
Minimum input voltage for valid RESET
MIN
0.15
0.4
V
1
µA
220
Dropout voltage (see Note 6)
IO = 150 mA,
IO = 150 mA,
TJ = 25°C
150
2 8 V Output
2.8-V
TJ = 25°C
115
3 3 V Output
3.3-V
IO = 150 mA,
IO = 150 mA
5 0 V Output
5.0-V
IO = 150 mA,
IO = 150 mA
TJ = 25°C
ms
265
mV
200
75
115
NOTE 6: IN voltage equals VO(typ) – 100 mV; 1.5 V, 1.8 V, and 2.7 V dropout voltage limited by input voltage range limitations (i.e., 3.3 V input
voltage needs to drop to 3.2 V for purpose of this test).
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
vs Output current
2, 3
vs Junction temperature
4, 5
Ground current
vs Junction temperature
6
Power supply rejection ratio
vs Frequency
7
Output spectral noise density
vs Frequency
8
Zo
Output impedance
vs Frequency
9
vs Input voltage
10
VDO
Dropout voltage
vs Junction temperature
11
VO
Output voltage
Line transient response
12, 14
Load transient response
8
13, 15
Output voltage and enable pulse
vs Time
Equivalent series resistance (ESR)
vs Output current
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
16
18 – 21
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TPS77x33
TPS77x18
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
3.302
1.802
3.301
1.801
VO – Output Voltage – V
VO – Output Voltage – V
TYPICAL CHARACTERISTICS
3.3
1.800
1.799
3.299
3.298
1.798
0
50
100
IO – Output Current – mA
0
150
50
100
IO – Output Current – mA
Figure 2
Figure 3
TPS77x33
TPS77x18
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
1.86
3.35
VI = 2.8 V
VI = 4.3 V
1.84
VO – Output Voltage – V
VO – Output Voltage – V
3.33
IO = 150 mA
3.31
3.29
1.82
IO = 150 mA
1.80
1.78
3.27
3.25
–40
150
0
40
80
120
TJ – Junction Temperature – °C
160
1.76
–40
0
40
80
120
160
TJ – Junction Temperature – °C
Figure 5
Figure 4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77xxx
GROUND CURRENT
vs
JUNCTION TEMPERATURE
115
110
Ground Current – µ A
IO = 150 mA
105
100
95
IO = 1 mA
90
85
80
–40
10
60
110
160
TJ – Junction Temperature – °C
Figure 6
TPS77x33
TPS77x33
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
10
CO = 10 µF
TJ = 25°C
IO = 1 mA
90
Output Spectral Noise Density – µV Hz
PSRR – Power Supply Rejection Ratio – dB
100
80
70
60
50
40
30
IO = 150 mA
20
10
0
10
100
1k
10k
100k
1M
10M
IO = 150 mA
1
IO = 1 mA
0.1
0.01
100
f – Frequency – Hz
1k
10k
f – Frequency – Hz
Figure 7
10
CO = 10 µF
TJ = 25°C
Figure 8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
100k
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77x33
OUTPUT IMPEDANCE
vs
FREQUENCY
10
Zo – Output Impedance – Ω
IO = 1 mA
1
0.1
IO = 150 mA
0.01
10
100
1k
10k
100k
f – Frequency – Hz
1M
10M
Figure 9
TPS77x01
TPS77x33
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
300
250
250
TJ = 125 °C
200
VDO – Dropout Voltage – mV
VDO – Dropout Voltage – mV
IO = 150 mA
TJ = 25 °C
TJ = –40 °C
150
100
50
200
IO = 150 mA
150
100
IO = 10 mA
50
IO = 0 A
0
0
2.7
3.2
3.7
4.2
VI – Input Voltage – V
4.7
–50
–40
0
40
80
120
TJ – Junction Temperature – °C
160
Figure 11
Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77x18
I O – Output Current – mA
TPS77x18
VI – Input Voltage – V
LINE TRANSIENT RESPONSE
3.8
2.8
∆ VO – Change in
Output Voltage – mV
∆ VO – Change in
Output Voltage – mV
10
0
–10
IO = 150 mA
CO = 10 µF
TJ = 25°C
0
0.1
0.2 0.3
0.4 0.5 0.6 0.7 0.8
t – Time – ms
0.9
LOAD TRANSIENT RESPONSE
150
0
0
–50
IO = 150 mA
CO = 10 µF
TJ = 25°C
–100
0
1
0.1
TPS77x33
LOAD TRANSIENT RESPONSE
I O – Output Current – mA
TPS77x33
LINE TRANSIENT RESPONSE
5.3
4.3
0.9
1
150
0
+10
∆ VO – Change in
Output Voltage – mV
∆ VO – Change in
VI – Input Voltage – V
Output Voltage – mV
0.4 0.5 0.6 0.7 0.8
t – Time – ms
Figure 13
Figure 12
0
–10
IO = 150 mA
CO = 10 µF
TJ = 25°C
0
0.1
0.2 0.3
0.4 0.5 0.6 0.7 0.8
t – Time – ms
0.9
1
0
–50
IO = 150 mA
CO = 10 µF
TJ = 25°C
–100
0
0.1
0.2 0.3
0.4 0.5 0.6 0.7 0.8
t – Time – ms
Figure 15
Figure 14
12
0.2 0.3
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
0.9
1
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77x33
VO – Output Voltage – V
Enable Pulse – V
OUTPUT VOLTAGE AND
ENABLE PULSE
vs
TIME (AT STARTUP)
CO = 10 µF
TJ = 25°C
EN
0
0
0
0.2 0.4
0.6
0.8 1.0 1.2 1.4
t – Time – ms
1.6 1.8
2.0
Figure 16
VI
To Load
IN
OUT
+
EN
RL
CO
GND
ESR
Figure 17. Test Circuit for Typical Regions of Stability (Figures 18 through 21) (Fixed Output Options)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
10
10
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
Region of Instability
Region of Instability
VO = 3.3 V
CO = 1 µF
VI = 4.3 V
TJ = 25°C
1
Region of Stability
1
Region of Stability
0.1
VO = 3.3 V
CO = 10 µF
VI = 4.3 V
TJ = 25°C
Region of Instability
0.1
0
50
100
0.01
150
Region of Instability
0
50
IO – Output Current – mA
Figure 18
150
Figure 19
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
100
IO – Output Current – mA
VO = 3.3 V
CO = 1 µF
VI = 4.3 V
TJ = 125 °C
1
Region of Stability
1
Region of Stability
0.1
VO = 3.3 V
CO = 10 µF
VI = 4.3 V
TJ = 125°C
Region of Instability
0.1
0
50
100
150
Region of Instability
0.01
0
IO – Output Current – mA
50
100
150
IO – Output Current – mA
Figure 20
Figure 21
† Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to CO.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
pin functions
enable (EN)
The EN terminal is an input which enables or shuts down the device. If EN is a logic high, the device will be in
shutdown mode. When EN goes to logic low, then the device will be enabled.
power good (PG) (TPS772xx)
The PG terminal is an open drain, active high output that indicates the status of Vout (output of the LDO). When
Vout reaches 82% of the regulated voltage, PG will go to a high-impedance state. It will go to a low-impedance
state when Vout falls below 82% (i.e. over load condition) of the regulated voltage. The open drain output of the
PG terminal requires a pullup resistor.
sense (SENSE)
The SENSE terminal of the fixed-output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, SENSE connects to a high-impedance wide-bandwidth amplifier
through a resistor-divider network and noise pickup feeds through to the regulator output. It is essential to route
the SENSE connection in such a way to minimize/avoid noise pickup. Adding RC networks between the SENSE
terminal and Vout to filter noise is not recommended because it may cause the regulator to oscillate.
feedback (FB)
FB is an input terminal used for the adjustable-output options and must be connected to an external feedback
resistor divider. The FB connection should be as short as possible. It is essential to route it in such a way to
minimize/avoid noise pickup. Adding RC networks between FB terminal and Vout to filter noise is not
recommended because it may cause the regulator to oscillate.
reset (RESET) (TPS771xx)
The RESET terminal is an open drain, active low output that indicates the status of Vout. When Vout reaches 95%
of the regulated voltage, RESET will go to a high-impedance state after a 220-ms delay. RESET will go to a
low-impedance state when Vout is below 95% of the regulated voltage. The open-drain output of the RESET
terminal requires a pullup resistor.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
external capacitor requirements
An input capacitor is not usually required; however, a bypass capacitor (0.047 µF or larger) improves load
transient response and noise rejection if the TPS771xx or TPS772xx is located more than a few inches from
the power supply. A higher-capacitance capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Most low noise LDOs require an external capacitor to further reduce noise. This will impact the cost and board
space. The TPS771xx and TPS772xx have very low noise specification requirements without using any external
components.
Like all low dropout regulators, the TPS771xx or TPS772xx requires an output capacitor connected between
OUT (output of the LDO) and GND (signal ground) to stabilize the internal control loop. The minimum
recommended capacitance value is 1 µF provided the ESR meets the requirement in Figures 19 and 21. In
addition, a low-ESR capacitor can be used if the capacitance is at least 10 µF and the ESR meets the
requirements in Figures 18 and 20. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic
capacitors are all suitable, provided they meet the requirements described previously.
Ceramic capacitors have different types of dielectric material with each exhibiting different temperature and
voltage variation. The most common types are X5R, X7R, Y5U, Z5U, and NPO. The NPO type ceramic type
capacitors are generally the most stable over temperature. However, the X5R and X7R are also relatively stable
over temperature (with the X7R being the more stable of the two) and are therefore acceptable to use. The Y5U
and Z5U types provide high capacitance in a small geometry, but exhibit large variations over temperature;
therefore, the Y5U and Z5U are not generally recommended for use on this LDO. Independent of which type
of capacitor is used, one must make certain that at the worst case condition the capacitance/ESR meets the
requirement specified in Figures 18 – 21.
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
Figure 22 shows the output capacitor and its parasitic impedances in a typical LDO output stage.
IO
LDO
–
VESR
RESR
+
+
VI
RLOAD
VO
–
CO
Figure 22. LDO Output Stage With Parasitic Resistances ESR and ESL
In steady state (dc state condition), the load current is supplied by the LDO (solid arrow) and the voltage across
the capacitor is the same as the output voltage (VCout = Vout). This means no current is flowing into the Cout
branch. If Iout suddenly increases (transient condition), the following occurs:
D The LDO is not able to supply the sudden current need due to its response time (t1 in Figure 23). Therefore,
capacitor Cout provides the current for the new load condition (dashed arrow). Cout now acts like a battery
with an internal resistance, ESR. Depending on the current demand at the output, a voltage drop will occur
at RESR. This voltage is shown as VESR in Figure 22.
D When Cout is conducting current to the load, initial voltage at the load will be Vout = VCout – VESR. Due to
the discharge of Cout, the output voltage Vout will drop continuously until the response time t1 of the LDO
is reached and the LDO will resume supplying the load. From this point, the output voltage starts rising again
until it reaches the regulated voltage. This period is shown as t2 in Figure 23.
The figure also shows the impact of different ESRs on the output voltage. The left brackets show different levels
of ESRs where number 1 displays the lowest and number 3 displays the highest ESR.
From above, the following conclusions can be drawn:
D The higher the ESR, the larger the droop at the beginning of load transient.
D The smaller the output capacitor, the faster the discharge time and the bigger the voltage droop during the
LDO response period.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
conclusion
To minimize the transient output droop, capacitors must have a low ESR and be large enough to support the
minimum output voltage requirement.
Iout
Vout
1
2
ESR 1
3
ESR 2
ESR 3
t1
t2
Figure 23. Correlation of Different ESRs and Their Influence to the Regulation of Vout at a
Load Step From Low-to-High Output Current
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
programming the TPS77x01 adjustable LDO regulator
The output voltage of the TPS77x01 adjustable regulator is programmed using an external resistor divider as
shown in Figure 24. The output voltage is calculated using:
V
O
+V
ǒ1 ) R1
Ǔ
R2
ref
(1)
Where:
Vref = 1.1834 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 50-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided, as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 30.1 kΩ to set the divider current at 50 µA and then calculate R1 using:
R1 +
ǒ
V
V
Ǔ
O *1
ref
(2)
R2
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS77x01
VI
0.1 µF
PG or
RESET
IN
PG or RESET Output
250 kΩ
EN
OUT
VO
R1
FB/SENSE
GND
CO
R2
OUTPUT
VOLTAGE
R1
R2
UNIT
2.5 V
33.5
30.1
kΩ
3.3 V
53.8
30.1
kΩ
3.6 V
61.5
30.1
kΩ
NOTE: To reduce noise and prevent
oscillation, R1 and R2 need to be as
close as possible to the FB/SENSE
terminal.
Figure 24. TPS77x01 Adjustable LDO Regulator Programming
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
regulator protection
The TPS771xx or TPS772xx PMOS-pass transistor has a built-in back diode that conducts reverse currents
when the input voltage drops below the output voltage (e.g., during power down). Current is conducted from
the output to the input and is not internally limited. When extended reverse voltage is anticipated, external
limiting may be appropriate.
The TPS771xx or TPS772xx also features internal current limiting and thermal protection. During normal
operation, the TPS771xx or TPS772xx limits output current to approximately 0.9 A. When current limiting
engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is
designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of
the package. If the temperature of the device exceeds 150°C(typ), thermal-protection circuitry shuts it down.
Once the device has cooled below 130°C(typ), regulator operation resumes.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than
or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
P
D(max)
T max * T
A
+ J
R
qJA
Where:
TJmax is the maximum allowable junction temperature.
RθJA is the thermal resistance junction-to-ambient for the package, i.e., 266.2°C/W for the 8-terminal
MSOP with no airflow.
TA is the ambient temperature.
The regulator dissipation is calculated using:
P
D
ǒ
Ǔ
+ V *V
I
O
I
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
MECHANICAL DATA
DGK (R-PDSO-G8)
PLASTIC SMALL-OUTLINE PACKAGE
0,38
0,25
0,65
8
0,25 M
5
0,15 NOM
3,05
2,95
4,98
4,78
Gage Plane
0,25
1
0°–ā6°
4
3,05
2,95
0,69
0,41
Seating Plane
1,07 MAX
0,15
0,05
0,10
4073329/B 04/98
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC MO-187
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
PACKAGE OPTION ADDENDUM
www.ti.com
6-Aug-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS77101DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77101DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77101DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77101DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77115DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77115DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77115DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77115DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77118DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77118DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77118DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77118DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77127DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77127DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77127DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77127DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77128DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77128DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77128DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77128DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77133DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77133DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77133DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77133DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77150DGK
ACTIVE
MSOP
DGK
8
CU NIPDAU
Level-1-260C-UNLIM
80
Addendum-Page 1
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
6-Aug-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS77150DGKG4
ACTIVE
MSOP
DGK
8
TPS77150DGKR
ACTIVE
MSOP
DGK
TPS77150DGKRG4
ACTIVE
MSOP
TPS77201DGK
ACTIVE
TPS77201DGKG4
80
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77201DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77201DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77215DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77215DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77215DGKRG4
ACTIVE
MSOP
DGK
8
TBD
Call TI
TPS77218DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77218DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77218DGKRG4
ACTIVE
MSOP
DGK
8
TBD
Call TI
TPS77227DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77227DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77227DGKRG4
ACTIVE
MSOP
DGK
8
TBD
Call TI
Call TI
TPS77228DGKG4
ACTIVE
MSOP
DGK
8
TBD
Call TI
Call TI
TPS77228DGKRG4
ACTIVE
MSOP
DGK
8
TBD
Call TI
Call TI
TPS77233DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77233DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77233DGKRG4
ACTIVE
MSOP
DGK
8
TBD
Call TI
TPS77250DGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77250DGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77250DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS77250DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
Call TI
Call TI
Call TI
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
6-Aug-2007
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Aug-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
4-Aug-2007
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS77101DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77115DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77118DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77127DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77128DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77133DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77150DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77201DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TPS77250DGKR
DGK
8
HNT
330
12
5.3
3.4
1.4
8
12
NONE
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
TPS77101DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77115DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77118DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77127DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77128DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77133DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77150DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77201DGKR
DGK
8
HNT
358.0
335.0
35.0
TPS77250DGKR
DGK
8
HNT
358.0
335.0
35.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Aug-2007
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated