STMICROELECTRONICS STMPE1601TBR

STMPE1601
16-bit enhanced port expander with keypad and PWM controller
Xpander Logic
Features
■
16 GPIOs
(8 operate at core supply VCC , 8 operate at IO
supply Vio)
■
Operating voltage 1.8 − 3.3 V
■
Hardware keypad controller (8*8 matrix with 4
optional dedicated keys max)
■
Keypad controller capable of detecting keypress in hibernation mode
■
4 basic PWM controller for LED brightness
control
■
Interrupt output (open drain) pin
■
Optional 32 kHz clock input
■
8-channel programmable level translator
■
Advanced power management system
■
Ultra-low standby-mode current
■
Package TFBGA25 (3 x 3 mm)
TFBGA25
Description
The STMPE1601 is a GPIO (general purpose
input/output) port expander able to interface a
main digital ASIC via the two-line bidirectional bus
(I2C). A separate GPIO expander IC is often used
in mobile multimedia platforms to solve the
problems of the limited number of GPIOs typically
available on the digital engine.
The STMPE1601 offers great flexibility, as each
I/O can be configured as input, output or specific
functions. The device is able to scan a keyboard,
also provides PWM outputs for brightness control
in backlight, and GPIO. This device has been
designed to include very low quiescent current,
and a wake-up feature for each I/O, to optimize
the power consumption of the IC.
Potential applications of the STMPE1601 include
portable media players, game consoles, mobile
and smart phones.
Table 1.
Device summary
Order code
Package
Packaging
STMPE1601TBR
TFBGA25
Tape and reel
June 2008
Rev 4
1/61
www.st.com
61
Contents
STMPE1601
Contents
1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
4
2.1
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2
Pin assignment and TFBGA ball location . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3
Pin mapping to TFBGA (top through view) . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4
GPIO pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1
Absolute maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1
DC electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2
Input/Output DC electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . 10
5
Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6
I2C interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7
2/61
6.1
Minimizing current drain on I2C address lines . . . . . . . . . . . . . . . . . . . . . 13
6.2
Start condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.3
Stop condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.4
Acknowledge bit (ACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.5
Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.6
Slave device address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.7
Memory addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.8
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.9
General call address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
System controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.1
States of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.2
Autosleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.3
Keypress detect in the hibernate mode . . . . . . . . . . . . . . . . . . . . . . . . . . 21
STMPE1601
8
9
Contents
Clocking system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.1
Clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.2
Power mode programming sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Interrupt system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.1
Interrupt system register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.1.1
9.2
10
12
Programming sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
GPIO controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.1
GPIO control registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
10.2
GPIO alternate function registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10.3
Hotkey feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
10.4
11
Interrupt latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10.3.1
Programming sequence for Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
10.3.2
Minimum pulse width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Level translator feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Basic PWM controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11.1
Interrupt on basic PWM controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
11.2
Trigger feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Keypad controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
12.1
Keypad configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
12.2
Registers in keypad controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
13
Data registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
14
Keypad combination key registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
15
Miscellaneous features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
15.1
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
15.2
Under voltage lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
16
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
17
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
3/61
Block diagram
1
STMPE1601
Block diagram
Figure 1.
STMPE1601 block diagram
Keypad controller
MUX
Keypad input (column x0-x7)
/GPIO 0-7
/PWM 0-3
(Powered by VCC)
Main FSM
PWM
GPIO control
MUX
CLK_IN
INT
SCLK
SDAT
Keypad output (row y0-y7)
/ADDR 0-2
/GPIO 8-15
(Powered by Vio)
I2C
Interface
GND1
GND2
A0
A1
A2
POR
VCC
VIO
CS00024
4/61
STMPE1601
Pin settings
2
Pin settings
2.1
Pin connection
Figure 2.
Pin connection (bottom view)
1
2
3
4
5
TFBGA25
2.2
Pin assignment and TFBGA ball location
Table 2.
Pin assignment
Ball name
Name
Type
Description
E5
GPIO_0
I/O
GPIO 0/ KP_X0/ PWM_0
D4
GPIO_1
I/O
GPIO 1/ KP_X1/ PWM_1
D5
GPIO_2
I/O
GPIO 2/ KP_X2/ PWM_2
C4
GPIO_3
I/O
GPIO 3/ KP_X3/ PWM_3
A5
GPIO_4
I/O
GPIO 4/ KP_X4
A4
GPIO_5
I/O
GPIO 5/ KP_X5
B3
GPIO_6
I/O
GPIO 6/ KP_X6
A3
GPIO_7
I/O
GPIO 7/ KP_X7
A2
GPIO_8
I/O
GPIO 8/ KP_Y0
A1
GPIO_9
I/O
GPIO 9/ KP_Y1
B2
GPIO_10
I/O
GPIO 10/ KP_Y2
5/61
Pin settings
STMPE1601
Table 2.
2.3
Ball Name
Name
Type
B1
GPIO_11
IO
GPIO 11/ KP_Y3
D1
GPIO_12
IO
GPIO 12/ KP_Y4
D2
GPIO_13
IO
GPIO 13/ KP_Y5/ ADDR0
E1
GPIO_14
IO
GPIO 14/ KP_Y6/ ADDR1
E2
GPIO_15
IO
GPIO 15/ KP_Y7/ ADDR2
B5
INT
O
Open drain interrupt output pin
E4
Reset_N
I
External reset input, active LOW. Reset_N pulse
width must be ≥ 20 μs.
E3
SDATA
A
I2C DATA
D3
SCLK
A
I2C clock
B4
CLK_IN
A
32 kHz input
C5
VCC
-
1.8 − 3.3 V input for I2C module and digital core
C1
VIO
-
1.8 − 3.3 V input for GPIO. The VIO must be ≥
VCC.
C2
GND
-
Ground
C3
GND
-
Ground
Description
Pin mapping to TFBGA (top through view)
Table 3.
6/61
Pin assignment (continued)
Pin mapping
1
2
3
4
5
A
GPIO_9
GPIO_8
GPIO_7
GPIO_5
GPIO_4
B
GPIO_11
GPIO_10
GPIO_6
CLK_IN
INT
C
VIO
GND
GND
GPIO_3
VCC
D
GPIO_12
GPIO_13
SCLK
GPIO_1
GPIO_2
E
GPIO_14
GPIO_15
SDATA
RESET_N
GPIO_0
STMPE1601
2.4
Pin settings
GPIO pin functions
Table 4.
GPIO pin functions
Name
Primary
function
Alternate
function 1
Alternate
function 2
GPIO_0
GPIO
Keypad
PWM
GPIO_1
GPIO
Keypad
PWM
GPIO_2
GPIO
Keypad
PWM
GPIO_3
GPIO
Keypad
PWM
GPIO_4
GPIO
Keypad
GPIO_5
GPIO
Keypad
GPIO_6
GPIO
Keypad
GPIO_7
GPIO
Keypad
GPIO_8
GPIO
Keypad
GPIO_9
GPIO
Keypad
GPIO_10
GPIO
Keypad
GPIO_11
GPIO
Keypad
GPIO_12
GPIO
Keypad
GPIO_13
GPIO
Keypad
I2C ADDR during RESET
GPIO_14
GPIO
Keypad
I2C ADDR during RESET
GPIO_15
GPIO
Keypad
I2C ADDR during RESET
Note
7/61
Maximum rating
3
STMPE1601
Maximum rating
Stressing the device above the rating listed in the “Absolute maximum ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
3.1
Absolute maximum rating
Table 5.
Absolute maximum rating
Symbol
Parameter
Supply voltage
4.5
V
VIN
Input voltage on GPIO pin
4.5
V
2
kV
ESD protection on each GPIO pin
Thermal data
Table 6.
Symbol
RthJA
8/61
Unit
VCC
VESD (HBM)
3.2
Value
Thermal data
Parameter
Min
Thermal resistance junction-ambient
Typ
Max
100
Unit
°C/W
TA
Operating ambient temperature
-40
25
85
°C
TJ
Operating junction temperature
-40
25
125
°C
STMPE1601
Electrical specification
4
Electrical specification
4.1
DC electrical characteristics
Table 7.
DC electrical characteristics
Value
Symbol
Parameter
Test conditions
Unit
Min
Typ
Max
VCC
1.8 V supply voltage
1.65
3.6
V
VIO
IO supply voltage
1.65
3.6
V
ICC
Active current
1.2
1.6
mA
18
25
μA
0.5
1.5
μA
3.0
3.8
mA
50
60
μA
1.2
3
μA
2
mA
32
μA
2
μA
4.8
mA
75
μA
5
μA
ISLEEP
IHIBERNATE
ICC
ISLEEP
IHIBERNATE
ICC
ISLEEP
IHIBERNATE
ICC
ISLEEP
IHIBERNATE
INT
Sleep current
VIO VCC = 1.8 V
T= 25 °C
Hibernate current
Active current
Sleep current
VIO VCC = 3.3 V
T= 25 °C
Hibernate current(1)
Active current
Sleep current
VIO VCC = 1.8 V
T= 85 °C
Hibernate current
Active current
Sleep current
Hibernate
VIO VCC = 3.3 V
T= 85 °C
current(1)
Open drain output
current
4
mA
1. If only the basic GPIO function is required, the STMPE1601 could be designed to work mostly in hibernate
mode. Active mode is used only when there are any changes in the I/O status.
9/61
Electrical specification
4.2
STMPE1601
Input/Output DC electrical characteristics
The 1.8 V I/O complies to the EIA/JEDEC standard JESD8-7.
Table 8.
I/O DC electrical characteristic
Value
Symbol
Parameter
Unit
Min
Vil
Low level input voltage
VIO = 1.8 V
Vih
High level input voltage
VIO = 1.8 V
Schmitt trigger hysteresis
VIO = 1.8 V
Vil
Low level input voltage
VIO = 3.3 V
Vih
High level input voltage
VIO = 3.3 V
Schmidt trigger hysteresis
VIO = 3.3 V
Vhyst
Vhyst
Table 9.
Symbol
Max
0.63
1.17
V
V
0.10
V
1.15
2.14
V
V
0.20
V
DC input specification (1.55 V < VCC < 1.95 V)
Parameter
Test
conditions
Vol
Low level output voltage
Iol = 4 mA
VIO = 1.8 V
Voh
High level output voltage
Ioh = 4 mA
VIO = 1.8 V
Vol
Low level output voltage
Iol = 4 mA
VIO = 3.3 V
Voh
High level output voltage
Ioh = 4 mA
VIO = 3.3 V
Table 10.
Typ
Value
Unit
Min
Typ
Max
0.45
1.35
V
V
0.83
2.48
V
V
DC output specification (1.55 V < VCC < 1.95 V)
Value
Symbol
Parameter
Unit
Min
Typ
Max
Pull-up current
Vi = 0 V
15
35
65
μA
Rup(1)
Equivalent pull-up
resistance
VCC = 3.3 V
30
60
90
KΩ
VCC = 1.8 V
50
100
150
KΩ
Rup(2)
Equivalent pull-up
resistance
VIO = 3.3 V
30
60
90
KΩ
VIO = 1.8 V
50
100
150
KΩ
Ipu
1. Applicable to GPIO_0 to GPIO_7.
2. Applicable to GPIO_8 to GPIO_15.
10/61
Test conditions
STMPE1601
5
Register map
Register map
All the registers have the size of 8-bit. For each of the module, their registers are residing
within the given address range.
Table 11.
Register map summary table
Address
Module register
Description
Auto-increment
(during read/write)
0x00 – 0x07
0x80 – 0x81
Clock and power
manager module
Clock and power manager register
range
Yes
0x10 – 0x1F
Interrupt controller
module
Interrupt controller register range
Yes
0x30 – 0x37
PWM controller module PWM controller register range
Yes
0x38 – 0x3F
PWM controller module PWM controller register range
No
0x60 – 0x6F
Keypad controller
module
Keypad controller register range
Yes
0x70 – 0x77
Rotator controller
module
Rotator controller register range
Yes
0x82 – 0xBF
GPIO controller module GPIO controller register range
Yes
11/61
I2C interface
6
STMPE1601
I2C interface
The features that are supported by the I2C interface are listed below:
●
I2C slave device
●
Operates at VCC (1.8 - 3.3 V)
●
Compliant to Philips I2C specification version 2.1
●
Supports standard (up to 100kbps) and fast (up to 400 kbps) modes
●
7-bit and 10-bit device addressing modes
●
General Call
●
Start/Restart/Stop
●
Address up to 8 STMPE1601 devices via the I2C interface
The address is selected by the state of 3 pins. The state of the pins is read upon reset and
then the pins can be configured for normal operation. The pins have a pull-up or down to set
the address. The I2C interface module allows the connected host system to access the
registers in the STMPE1601.
I2C addresses
Table 12.
12/61
A2
A1
A0
7-bit address
0
0
0
40h
0
0
1
41h
0
1
0
42h
0
1
1
43h
1
0
0
44h
1
0
1
45h
1
1
0
46h
1
1
1
47h
STMPE1601
6.1
I2C interface
Minimizing current drain on I2C address lines
The GPIOs 13-15 are used as I2C address input during POR. Pull-up/down resistor of
500 K-1.5 M is recommended for these address lines. In the case that these pins are driven
to an opposite logic level during device operation, there would be a current drain of VIO/R.
This amounts to a significant current for portable devices.
To minimize the current drain on I2C lines, a few methods are recommended.
1.
If maximum keypad size is not required, these shared lines should not be used for
keypad operation.
2.
If the maximum keypad size is required, choose I2C address 0x40, as this requires that
all 3 address lines to be pulled to ground, minimizing the current drain in keypad
operation. In this mode of operation, the pull up/down resistors on the I2C lines should
be:
Table 13.
VIO
RPU/RPD
RPU/RPD
RPU/RPD
Recommended pull up/down resistors on the I2C lines
1.8 V
1.5 M
1.0 M
500 K
2.5 V
1.2 M
800 K
400 K
Reset RC
or pulse width(1)
Note
270 K/0.47 μF
120 ms
All 3 address
lines are
used for
keypad
controller
660 K
180 K/0.47 μF
80 ms
2 address
lines are
used for
keypad
controller
330 K
90K/0.47 μF
40 ms
3.3 V
1M
1 address
line is used
for keypad
controller
1. Recommended values are chosen to minimize leakage current.
A reset circuit with longer RC is used to ensure enough time for the address lines to
settle to the final values.
3.
In system-controlled idle state, all keypad pins to be configured as hotkey with interrupt
enabled. If any key is pressed, system initiates keypad controller for scanning
operation.
13/61
I2C interface
6.2
STMPE1601
Start condition
A Start condition is identified by a falling edge of SDATA while SCLK is stable at high state.
A Start condition must precede any data/command transfer. The device continuously
monitors for a Start condition and does not respond to any transaction unless one is
encountered.
6.3
Stop condition
A Stop condition is identified by a rising edge of SDATA while SCLK is stable at high state.
A Stop condition terminates the communication between the slave device and bus master. A
read command that is followed by NoAck can be followed by a Stop condition to force the
slave device into idle mode. When the slave device is in idle mode, it is ready to receive the
next I2C transaction. A Stop condition at the end of a write command stops the write
operation to the registers.
6.4
Acknowledge bit (ACK)
The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter
releases the SDATA after sending eight bits of data. During the ninth bit, the receiver pulls
the SDATA low to acknowledge the receipt of the eight bits of data. The receiver may leave
the SDATA in high state if it would to not acknowledge the receipt of the data.
6.5
Data input
The device samples the data input on SDATA on the rising edge of the SCLK. The SDATA
signal must be stable during the rising edge of SCLK and the SDATA signal must change
only when SCLK is driven low.
6.6
Slave device address
The slave device address is a 7 or 10-bit address, where the least significant 3-bit are
programmable. These 3-bit values will be loaded in once upon reset and after that these 3
pins no longer be needed with the exception during General Call. Up to 8 STMPE1601
devices can be connected on a single I2C bus.
6.7
Memory addressing
For the bus master to communicate to the slave device, the bus master must initiate a Start
condition and followed by the slave device address. Accompanying the slave device
address, there is a Read/Write bit (R/W). The bit is set to 1 for Read and 0 for Write
operation.
If a match occurs on the slave device address, the corresponding device gives an
acknowledgement on the SDA during the 9th bit time. If there is no match, it deselects itself
from the bus by not responding to the transaction.
14/61
STMPE1601
Operating modes
Table 14.
Operating modes
Mode
Bytes
Programming sequence
START, Device address, R/W = 0, Register address to be read
reSTART, Device address, R/W = 1, Data Read, STOP
If no STOP is issued, the Data Read can be continuously performed. If
the register address falls within the range that allows address autoincrement, then register address auto-increments internally after every
byte of data being read. For register address that falls within a nonincremental address range, the address will be kept static throughout
the entire read operations. Refer to the Memory Map table for the
address ranges that are auto and non-increment. An example of such
a non-increment address is FIFO.
≥1
Read
START, Device address, R/W = 0, Register address to be written, Data
Write, STOP.
≥1
Write
Stop
Data
Read + 2
No Ack
Data
Read + 1
Ack
Stop
No Ack
Ack
Data
Read
Data to
Write + 2
Ack
Stop
Data to
Write + 1
Ack
Ack
Restart
Data to
Write
Ack
Reg
Address
R/W=1
Ack
Restart
Data
to be
written
Ack
Reg
Address
R/W=1
Ack
Restart
Device
Address
Data
Read
Ack
Stop
Ack
Restart
Reg
Address
Ack
Ack
R/W=0
Ack
R/W=0
Device
Address
Device
Address
Ack
Device
Address
R/W=0
More than one byte
Read
Device
Address
Reg
Address
Ack
One byte
Write
Device
Address
R/W=0
More than one byte
Read
Start
One byte
Read
Start
I2C transaction
Start
Figure 3.
If no STOP is issued, the Data Write can be continuously performed. If
the register address falls within the range that allows address autoincrement, then register address auto-increments internally after every
byte of data being written. For those register addresses that fall within
a non-incremental address range, the address will be kept static
throughout the all write operations. Refer to the memory map table for
the address ranges that are auto and non-increment. An example of a
non-increment address is Data Port for initializing the PWM
commands.
Start
6.8
I2C interface
Master
Slave
15/61
I2C interface
6.9
STMPE1601
General call address
A general call address is a transaction with the slave address of 0x00 and R/W = 0. When a
general call address is made, STMPE1601 responds to this transaction with an
acknowledgement and behaves as a slave-receiver mode. The meaning of a general call
address is defined in the second byte sent by the master-transmitter.
Table 15.
Note:
16/61
General call address
R/W
Second byte value
Definition
0
0x06
A 2-byte transaction in which the second byte tells the slave
device to reset and write (or latch in) the 2-bit programmable part
of the slave address.
0
0x04
A 2-byte transaction in which the second byte tells the slave
device not to reset and write (or latch in) the 2-bit programmable
part of the slave address.
0
0x00
Not allowed as second byte.
All other second byte values will be ignored.
STMPE1601
7
System controller
System controller
The system controller is the heart of the STMPE1601. It contains the registers for power
control, and the registers for chip identification.
The system registers are:
Table 16.
System registers
Address
Register_Name
0x80
CHIP_ID
0x81
VERSION_ID
0x02
SYS_CTRL
0x03
SYS_CTRL_2
CHIP_ID
Chip identification register
7
6
5
4
R
R
R
R
0
0
0
0
3
2
1
0
R
R
R
R
0
0
1
0
2
1
0
8-bit MSB of CHIP_ID
VERSION_ID
Version identification register
7
6
5
4
3
R
R
R
R
R
R
R
R
0
0
0
1
0
0
0
0
8-bit VERSION_ID
17/61
System controller
STMPE1601
SYS_CTRL
System control register
7
6
5
4
3
2
1
0
SOFT_RESET
CLOCK
SOURCE
DIS_32KHz
SLEEP
EN_GPIO
RESERVED
EN_KPC
EN_SPWM
W
RW
RW
RW
RW
RW
RW
RW
RW
R
R
RW
R
R
R
R
0
0
0
0
1
0
1
1
Address:
0x02
Type:
R/W
Reset:
0x0B
Description:
System control register.
[7] SOFT_RESET
Writing a ‘1’ to this bit will do a soft reset of the device. Once the reset is done, this bit will be
cleared to ‘0’ by the HW.
[6] CLOCK_SOURCE
Set to ‘1’ if external 32 kHz clock were to be used. ‘0’ by default.
[5] DIS_32 kHz:
Set this bit to disable the 32 kHz OSC, thus putting the device in hibernate mode.
[4] SLEEP:
Writing a ‘1’ to this bit will put the device in sleep mode. On going to sleep mode, this mode is
reset internally. When in sleep mode, the internal RC oscillator will output a slower sleep clock
which will be used in the device.
[3] EN_GPIO:
Writing a ‘0’ to this bit will gate off the clock to the GPIO module, thus stopping its operation
[2] RESERVED
[1] EN_KPC:
Writing a ‘0’ to this bit will gate off the clock to the Keypad Controller module, thus stopping its
operation
[0] EN_SPWM
Writing a ‘0’ to this bit will gate off the clock to the Simple PWM Controller module, thus
stopping its operation
18/61
STMPE1601
System controller
SYS_CTRL_2
7
System control register 2
6
5
4
3
2
1
0
RESERVED
VIO_OFF
AUTOSLEEP_EN
SLEEP_2
SLEEP_1
SLEEP_0
R
R
RW
RW
RW
RW
0
0
0
0
0
0
Address:
0x03
Type:
R/W
Reset:
0x00
Description:
System control register
[7] RESERVED
[6] RESERVED
[5] RESERVED
[4] VIO_OFF:
Writing a ‘1’ to this bit is mandatory before shuting off the VIO supply while maintaining the
VCC supply.
This ensure that the level shifters for GPIOs 15-8 are properly powered down so as not to
induce high current and also not to affect the integrity of any external signals that are on the
bus where these GPIOs are connected.
[3] AUTOSLEEP_EN:
“1” to enable auto-sleep feature. “0” to disable auto-sleep.
[2:0] SLEEP:
000 for 4 mS delay
001 for 16 mS delay
010 for 32 mS delay
011: for 64 mS delay
100: for 128 mS delay
101: for 256 mS delay
110: for 512 mS delay
111: for 1024 mS delay
19/61
System controller
7.1
STMPE1601
States of operation
Figure 4.
Modes of operation
OPERATIONAL
32K: ON
RC: OFF
Set Sleep bit
or autosleep
Set Disable_32K bit
Keypad, Interrupts
&
I2 C transaction
SLEEP
32K: ON
RC: OFF
Reset
2
I C transaction
Valid Keypress
detect
HIBERNATE
32K: OFF
RC: OFF
The device has three main modes of operation:
Note:
20/61
●
Operational mode: This is the mode, whereby normal operation of the device takes
place. In this mode, the RC clock is available and the main FSM unit routes this clock
and the 32 KHz clock to all the device blocks that are enabled. In this mode, individual
blocks that need not to
be working can be turned off by the master by programming the bits 3 to 0 of the
SYS_CTRL register.
●
Sleep mode: In this low-power mode, the RC oscillator is powered down. All the blocks
which need clocks derived from the 32KHz clock will continue getting a 32 KHz clock.
In this mode also, iindividual blocks can be turned off by the master by programming
the bits 3 to 0 of the SYS_CTRL register. However, the master needs to program the
SYS_CTRL register before coming into this mode, as in the sleep mode, the IIC
interface is not active except to detect traffic for wakeup. Any activity on the I2C port
(intended I2C transaction for the device) or Wakeup pin or Hotkey activity will cause the
device to leave this mode and go into the Operational mode. When leaving this mode,
the I2C will need to hold the SCLK till the RC clock is ready.
●
Hibernate mode: This mode is entered when the system writes a ‘1’ to bit 5 of the
SYS_CTRL register. In this mode, the device is completely inactive as there is
absolutely no clock. Only a Reset or a wakeup on IIC will bring back the System to
operational mode. A keypress detect will bring the system to Sleep mode, in which the
debounce of the key will take place.
The 32 kHz clock mentioned in this section can be (1) an externally fed 32 KHz clock, or (2)
an internally generated (from RC OSC) clock. In case the internal clock is used, the clock
has a range of 25 to 45 KHz.
STMPE1601
7.2
System controller
Autosleep
The host system may configure the STMPE1601 to go into sleep mode automatically
whenever there is a period of inactivity following a complete I2C transaction with the
STMPE1601. This inactivity means there is no intended I2C transaction for the device. For
example, if there is an I2C transaction sent by the host to other slave devices, the
STMPE1601 device will still be counting down for the auto-sleep. The STMPE1601 device
resets the autosleep time-out counter only when it receives an I2C transaction meant for the
device itself. This autosleep feature is controlled by the SYS_CTRL_2 (system control
register 2).
All those events that trigger an interrupt (KPC, hot-key) would result in a transition from
Sleep state to Operational state automatically. The wakeup can also be performed through
the I2C transaction intended for the device.
7.3
Keypress detect in the hibernate mode
When in Hibernate mode, a keypress detect causes the system to go into sleep mode. The
sleep clock (32 kHz) is then used to debounce the key to detect a valid key. If the keypress is
detected to be valid, the system stays in sleep mode. If the key is detected to be invalid, the
system goes back into Hibernate mode.
21/61
Clocking system
8
STMPE1601
Clocking system
Figure 5.
Clocking system
Internal RC
OSC
System clock
Clock control
CLK_IN
SCLK Pin
System control register
The decision on clocks is based on the bits written into the SYS_CTRL registers. Bits 0 to 4
of the SYS_CTRL register allow to control the gating of clocks to the Rotator, Keypad
controller, PWM and GPIO respectively in the operational mode.
8.1
Clock source
By default, when the STMPE1601 powers up, it derives a 32 KHz clock from the internal RC
oscillator for its operation. If an external clock source is available, it must be configured to
accept an external clock through the SYS_CTRL register.
Reset control: There are 4 sources of reset:
22/61
●
Reset_N pin
●
LVD reset
●
Soft reset bit of the SYS_CTRL register
●
I2C reset from the I2C block.
STMPE1601
8.2
Clocking system
Power mode programming sequence
To put the device in sleep mode, the following needs to be done by the host:
–
Write a '1' to bit 4 of the SYS_CTRL register.
To wake up the device, the host is required to:
–
Assert a wakeup routine on the I2C bus by sending the Start bit, followed by the
device address and the Write bit. Subsequently, proceed with sending the Base
Register address and continue with a normal I2C transaction. The device wakes
up upon receiving the correct device address and in Write direction. In other
words, the procedure of waking up the device is performed by just sending an I2C
transaction to the device. This procedure can be extended to wake up the device
that is in hibernate mode.
To do a soft reset to the device, the host needs to do the following:
–
Write a '1' to bit 7 of the SYS_CTRL register. This bit is automatically cleared upon
reset.
To go into Hibernate mode, the following needs to be done by the host:
–
Set the Disable_32K bit to '1'
To come out of the Hibernate mode, the following needs to be done by the host:
–
Assert a system reset
–
or put a wakeup on the I2C
23/61
Interrupt system
9
STMPE1601
Interrupt system
The STMPE1601 uses a highly flexible interrupt system. It allows the host system to
configure the type of system events that should result in an interrupt, and pinpoints the
source of interrupt by status register. The INT pin can be configured as ACTIVE HIGH, or
ACTIVE LOW.
Once asserted, the INT pin would de-assert only if the corresponding bit in the interrupt
status register is cleared.
Figure 6.
Interrupt system
Keypad
controller
Interrupt status
register
Interrupt
generation
PWM controller
Interrupt enable
register
GPIO controller
9.1
Interrupt polarity control
(System control register)
Interrupt system register map
Table 17.
Address
0x10
Register map
Register name
Description
INT_CTRL_MSB
Auto-increment
(during sequential R/W)
Yes
Interrupt control register
0x11
INT__CTRL_LSB
0x12
INT_EN_MASK_MSB
Yes
Yes
Interrupt enable mask register
0x13
INT_EN_MASK_LSB
0x14
INT_STA_MSB
Yes
Yes
Interrupt status register
0x15
INT_STA_LSB
0x16
INT_EN_GPIO_MASK
_MSB
Yes
Yes
Interrupt enable GPIO mask register
0x17
INT_EN_GPIO_MASK
_LSB
0x18
INT_STA_GPIO_MSB
Yes
Yes
Interrupt status GPIO register
0x19
24/61
INT_STA_GPIO_LSB
Yes
STMPE1601
9.1.1
Interrupt system
Interrupt latency
When the generation of interrupts by the GPIO as input is enabled, the latency (time taken
from actual transition at GPIO to time of INT pin assertion) is shown in the following table:
Table 18.
Interrupt latency
State of operation
Interrupt latency
Hibernation
10 uS max
Sleep
5 uS max
Active
2 uS max
INT_CTRL
15
14
Interrupt control register
13
12
11
10
9
8
7
6
5
INT_CTRL_msb
4
3
2
1
0
IC2
IC1
IC0
INT_CTRL_lsb
Reserved
R
R
R
R
R
R
R
R
R
R
R
R
R
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address:
0x10, 0x11
Type:
R, R/W
Reset:
0x00
Description:
The interrupt control register is used to configure the interrupt controller. It has a
global enable interrupt mask bit that controls the interruption to the host.
[15:3] RESERVED
[2] IC2: Output Interrupt polarity
‘0’ = Active low/falling edge
‘1’ = Active high/rising edge
[1] IC1: Output Interrupt Type
‘0’ = Level interrupt
‘1’ = Edge interrupt
[0] IC0: Global Interrupt Mask bit
When this bit is written a ‘1’, it will allow interruption to the host. If it is written with a ‘0’, then, it
disables all interruption to the host. Writing to this bit does not affect the INT_EN_MASK value.
25/61
Interrupt system
STMPE1601
INT_EN_MASK
15
14
13
Interrupt enable mask register
12
11
10
9
8
7
6
5
INT_EN_MASK_msb
4
3
2
1
0
INT_EN_MASK_lsb
IE8
IE7
IE6
IE5
IE4
IE3
IE2
IE1
IE0
R
R
R
R
R
R
R
RW
R/W
R/W
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address:
0x12, 0x13
Type:
R, R/W
Reset:
0x00
Description:
The interrupt enable mask register is used to enable the interruption from a particular
interrupt source to the host.
[15:9] RESERVED
[8] IE[x]:
Interrupt Enable Mask (where x = 8 to 0)
IE0: Wake-up interrupt mask
IE1: Keypad controller interrupt mask
IE2: Keypad controller FIFO overflow interrupt mask
IE3: Reserved
IE4: Basic PWM controller 0 interrupt mask
IE5: Basic PWM controller 1 interrupt mask
IE6: Basic PWM controller 2 interrupt mask
IE7: Basic PWM controller 3 interrupt mask
IE8: GPIO controller interrupt mask
Writing a ‘1’ to the IE[x] bit enables the interruption to the host.
26/61
STMPE1601
Interrupt system
INT_STA
15
Interrupt status register
14
13
12
11
10
9
8
7
6
5
ISR_msb
4
3
2
1
0
ISR_lsb
IS8
IS8
IS8
IS5
IS4
IS3
IS2
IS1
IS0
R
R
R
R
R
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address:
0x14, 0x15
Type:
R, R/W
Reset:
0x00
Description:
The interrupt status register monitors the status of the interruption from a particular
interrupt source to the host. Regardless whether the INT_EN bits are enabled or not,
the INT_STA bits are still updated.
[15:9] RESERVED
[8:0] IS[x]:
Interrupt status (where x = 8 to 0)
Read:
IE0: Wake-up Interrupt Status
IE1: Keypad controller interrupt status
IE2: Keypad controller FIFO overflow interrupt status
IE3: Reserved
IE4: Basic PWM controller 0 interrupt status
IE5: Basic PWM controller 1 interrupt status
IE6: Basic PWM controller 2 Interrupt status
IE7: Basic PWM controller 3 interrupt status
IE8: GPIO Controller Interrupt Status
Write: a write to a IS[x] bit with a value of ‘1’ will clear the interrupt and a write with a value of ‘0’
has no effect on the IS[x] bit.
27/61
Interrupt system
STMPE1601
INT_EN_GPIO_MASK
15
14
13
Interrupt enable GPIO mask register
12
11
10
9
8
7
6
INT_EN_GPIO_MASK_msb
5
4
3
2
1
0
INT_EN_GPIO_MASK _lsb
IEG15
IEG14
IEG13
IEG12
IEG11
IEG10
IEG9
IEG8
IEG7
IEG6
IEG5
IEG4
IEG3
IEG2
IEG1
IEG0
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address:
0x16, 0x17
Type:
R/W
Reset:
0x00
Description:
The interrupt enable GPIO mask register is used to enable the interruption from a
particular GPIO interrupt source to the host. The IEG[15:0] bits are the interrupt
enable mask bits correspond to the GPIO[15:0] pins
.
[15:0] IEG[x]: interrupt enable GPIO mask (where x = 15 to 0)
Writing a ‘1’ to the IE[x] bit will enable the interruption to the host.
INT_STA_GPIO
15
14
Interrupt status GPIO register
13
12
11
10
9
8
7
6
5
INT_STA_GPIOR_msb
4
3
2
1
0
INT_STA_GPIOR _lsb
ISG15
ISG14
ISG13
ISG12
ISG11
ISG10
ISG9
ISG8
ISG7
ISG6
ISG5
ISG4
ISG3
ISG2
ISG1
ISG0
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address:
0x18, 0x19
Type:
R/W
Reset:
0x00
Description:
The interrupt status GPIO register monitors the status of the interruption from a
particular GPIO pin interrupt source to the host. Regardless whether the
INT_EN_GPIO_MASK bits are enabled or not, the INT_STA_GPIO bits are still
updated. The INT_STA_G[15:0] bits are the interrupt status bits correspond to the
GPIO[15:0] pins.
[15:0] ISG[x]
Interrupt status GPIO (where x = 15 to 0)
Read:
Interrupt status of the GPIO[x].
Write:
A write to a ISG[x] bit with a value of ‘1’ will clear the interrupt and a write with a value of ‘0’ has
no effect on the ISG[x] bit.
28/61
STMPE1601
9.2
Interrupt system
Programming sequence
To configure and initialize the Interrupt Controller to allow interruption to host, observe the
following steps:
●
Set the INT_EN_MASK and INT_EN_GPIO_MASK registers to the desired values to
enable the interrupt sources that are to be expected to receive from.
●
Configure the output interrupt type and polarity and enable the global interrupt mask by
writing to the INT_CTRL.
●
Wait for interrupt.
●
Upon receiving an interrupt, the INT pin is asserted.
●
The host comes to read the INT_STA register through the I2C interface. A ‘1’ in the
INT_STA bits indicates that the corresponding interrupt source is triggered.
●
If the IS8 bit in INT_STA register is set, the interrupt is coming from the GPIO controller.
Then, a subsequent read is performed on the INT_STA_GPIO register to obtain the
interrupt status of all 16 GPIOs to locate the GPIO that triggers the interrupt. This is a
feature so-called ‘Hot Key’.
●
After obtaining the interrupt source that triggers the interrupt, the host performs the
necessary processing and operations related to the interrupt source.
●
If the interrupt source is from the GPIO Controller, two write operations with value of ‘1’
are performed to the ISG[x] bit (INT_STA_GPIO) and the IS[8] (ISR) to clear the
corresponding GPIO interrupt.
●
If the interrupt source is from other module, a write operation with value of ‘1’ is
performed to the IS[x] (ISR) to clear the corresponding interrupt.
●
Once the interrupt is being cleared, the INT pin will also be de-asserted if the interrupt
type is level interrupt. An edge interrupt will only assert a pulse width of 250ns.
●
When the interrupt is no longer required, the IC0 bit in INT_CTRL may be set to ‘0’ to
disable the global interrupt mask bit.
29/61
GPIO controller
10
STMPE1601
GPIO controller
A total of 16 GPIOs are available in the STMPE1601 port expander IC. Most of the GPIOs
are sharing physical pins with some alternate functions. The GPIO controller contains the
registers that allow the host system to configure each of the pins into either a GPIO, or one
of the alternate functions. Unused GPIOs should be configured as outputs to minimize the
power consumption.
Table 19.
GPIO controller
Offset address
0x02
Register name
Description
GPIO_SET_MSB
Auto-increment
(during sequential R/W)
Yes
GPIO set pin state register
0x03
GPIO_SET_LSB
0x04
GPIO_CLR_msb
Yes
Yes
GPIO clear pin state register
0x05
GPIO_CLR_LSB
0x06
GP_MP_MSB
Yes
Yes
GPIO monitor pin state register
0x07
GPIO_MP_LSB
0x08
GPIO_SET_DIR_MSB
Yes
Yes
GPIO set pin direction register
0x09
GPIO_SET_DIR_LSB
0x0A
GPIO_ED_MSB
0x0B
GPIO_ED_LSB
0x0C
GPIO_RE_MSB
Yes
GPIO edge detect status
register
Yes
Yes
Yes
GPIO rising edge register
0x0D
GPIO_RE_LSB
0x0E
GPIO_FE_MSB
Yes
Yes
GPIO falling edge register
0x0F
GPIO_FE_LSB
0x10
GPIO_PULL_UP_MS
B
0x11
GPIO_PULL_UP_LSB
0x12
GPIO_AF_U_MSB
0x13
GPIO_AF_U_MSB
0x14
GPIO_AF_L_MSB
0x15
Yes
GPIO pull up register
Yes
GPIO alternate function
register (upper word)
Yes
Yes
Yes
GPIO_AF_L_LSB
GPIO alternate function
register (lower word)
Yes
0x16
GPIO_LT_EN
GPIO level translator enable
Yes
0x17
GPIO_LT_DIR
GPIO level translator direction
Yes
RESERVED
Reserved
Yes
0x18-1F
30/61
Yes
STMPE1601
10.1
GPIO controller
GPIO control registers
A group of registers is used to control the exact function of each of the 16 GPIOs.
All the GPIO registers are named as GPxxx_yyy, where:
–
Xxx represents the functional group
–
Yyy represents the byte position of the GPIO
–
Lsb registers control GPIO[7:0]
–
Msb registers control GPIO[8:15]
Table 20.
Bit description
7
6
5
4
3
2
1
0
GPxxx_msb
IO-15
IO-14
IO-13
IO-12
IO-11
IO-10
IO-9
IO-8
GPxxx_lsb
IO-7
IO-6
IO-5
IO-4
IO-3
IO-2
IO-1
IO-0
The function of each bit is shown in the following table:
Table 21.
Register description
Register name
Function
GPIO monitor pin state
Reading this bit yields the current state of the bit. Writing has no effect.
GPIO set pin state
Writing ‘1’ to this bit causes the corresponding GPIO to go to ‘1’ state.
Writing ‘0’ has no effect.
GPIO clear pin state
Writing ‘1’ to this bit causes the corresponding GPIO to go to ‘0’ state.
Writing ‘0’ has no effect.
GPIO set pin direction
‘0’ sets the corresponding GPIO to input state, and ‘1’ sets it to output
state
GPIO edge detect status
Set to ‘1’ by hardware when there is a rising/falling edge on the
corresponding GPIO. Writing ‘1’ clears the bit. Writing ‘0’ has no effect.
GPIO rising edge
Set to ‘1’ to enable rising edge detection on the corresponding GPIO.
GPIO falling edge
Set to ‘1’ to enable falling edge detection on the corresponding GPIO.
GPIO pull up
Set to ‘1’ to enable internal pull-up resistor
31/61
GPIO controller
10.2
STMPE1601
GPIO alternate function registers
Each GPIO may be configured to one or more functions. A 2-bit field for each GPIO is used
for the configuration.
Table 22.
GPIO alternate function registers
GPIO alternate function
(upper word)
GPIO alternate function
(lower word)
‘00’ for primary function
‘01’ for Alternate Function 1
‘10’ for Alternate Function 2
‘11’ - Reserved
GPIO alternate function registers (upper)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
GPIO-15
GPIO-14
GPIO-13
GPIO-12
GPIO-11
GPIO-10
GPIO-9
GPIO-8
GPIO alternate function registers (lower)
15
32/61
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
AF[1:0]
GPIO-7
GPIO-6
GPIO-5
GPIO-4
GPIO-3
GPIO-2
GPIO-1
GPIO-0
STMPE1601
10.3
GPIO controller
Hotkey feature
A GPIO is known as ‘Hotkey’ when it is configured to trigger an interruption to the host
whenever the GPIO input is being asserted. This feature is applicable in Operational mode
(4 MHz clock is present) as well as Sleep mode (32 kHz clock is present).
10.3.1
Programming sequence for Hotkey
1.
Configure the GPIO pin into GPIO mode by setting the corresponding bits in the
GPAFR.
2.
Configure the GPIO pin into input direction by setting the corresponding bit in GPDR.
3.
Set the GPRER and GPFER to the desired values to enable the rising edge or falling
edge detection.
4.
Configure and enable the interrupt controller to allow the interruption to the host.
5.
Now, the GPIO expander may be put into Sleep mode if it is desired.
6.
Upon any hot-key being asserted, the device will wake up and issue an interrupt to the
host.
Below are the conditions to be fulfilled in order to configure a Hot Key:
10.3.2
1.
The pin is configured into GPIO mode and as input pin.
2.
The global interrupt mask bit is enabled.
3.
The corresponding GPIO interrupt mask bit is enabled.
Minimum pulse width
The minimum pulse width of the assertion of the Hotkey must be at least 62.5 us. Any pulse
width less than the stated value may not be registered.
33/61
GPIO controller
10.4
STMPE1601
Level translator feature
Figure 7.
Level translator feature
GPIO
0-7
Direction
&
enable
GPIO
8-15
When enabled, the GPIO 0-7 bits are internally mapped to GPIO 8-15 bits. The
STMPE1601 becomes an 8-channel level translator where each of the channels may have
its direction set individually. As GPIO 0-7 operates from Vcc, and GPIO 8-15 operates from
Vio, this allows the 2 groups of GPIO to work as a level translator.
Warning:
34/61
When the level translator feature is enabled, the “Set pin”,
“Clear pin” and “Set direction” bits in the corresponding
registers will be ignored. However, the “Monitor pin”, “Edge
detect”, “Pull-up” features are still available in the GPIOs
used as level translator.
STMPE1601
11
Basic PWM controller
Basic PWM controller
The advanced PWM allows complex brightness and blinking control of an LED. The basic
PWM controller allows simpler brightness control and basic blinking patterns. The
STMPE1601 is fitted with a 4-channel basic PWM controller.
Table 23.
Address
Basic PWM controller
Register name
Description
Auto-increment
(during sequential R/W)
0x40
PWM_OFF_OUT
Set the output level when PWM is
disabled
Yes
0x41
CHANNEL_FUNCT_EN
Enable/disable individual basic
PWM channels
Yes
0x50
PWM_0_SET
PWM_0 brightness and timing
setting
Yes
0x51
PWM_0_CTRL
PWM_0 blinking control
Yes
0x52
PWM_0_TRIGGER
Enable use trigger on PWM 0
Yes
0x54
PWM_1_SET
PWM_1 brightness and timing
setting
Yes
0x55
PWM_1_CTRL
PWM_1 blinking control
Yes
0x56
PWM_1_TRIGGER
Enable use trigger on PWM 1
Yes
0x58
PWM_2_SET
PWM_2 brightness and timing
setting
Yes
0x59
PWM_2_CTRL
PWM_2 blinking control
Yes
0x5A
PWM_2_TRIGGER
Enable use trigger on PWM 2
Yes
0x5C
PWM_3_SET
PWM_3 brightness and timing
setting
Yes
0x5D
PWM_3_CTRL
PWM_3 blinking control
Yes
0x5E
PWM_3_TRIGGER
Enable use trigger on PWM 3
Yes
35/61
Basic PWM controller
STMPE1601
PWM_OFF_OUTPUT
PWM off output
7
6
5
4
3
2
1
0
-
-
-
-
OUT3
OUT2
OUT1
OUT0
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Address:
0x40
Type:
R/W
Reset:
0x00
Description:
Set the output level when the PWM is disabled
[3:0] OUTPUT3~0:
Default is ‘0’
1: PWM channel outputs ‘1’ when disabled
0: PWM channel outputs ‘0’ when disabled
CHANNEL_FUNCT_EN
Channel function enabling
7
6
5
4
3
2
1
0
ALT_3
ALT_2
ALT_1
ALT_0
EN_3
EN_2
EN_1
EN_0
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Address:
0x41
Type:
R/W
Reset:
0x00
Description:
Enable/disable individual basic PWM channels.
[7:4] ALT [3:0]:
Alternate mode
Default is ‘0’
HW writes to ‘1’ if alternate operating feature (one-shot/WDT) is required
[3:0] EN [3:0]:
PWM channel enable
Default is ‘0’
SW writes ‘1’ to start PWM channel
HW writes ‘0’ when PWM blinking is completed.
SW writes ‘0’ to stop the PWM channel.
36/61
STMPE1601
Basic PWM controller
PWM_n_TRIGGER_n = 0 - 3
7
6
RESET
RW
0
Address:
PWM trigger register n = 0 - 3
5
4
3
2
1
0
Edge
-
MODE
RELOAD
GS2
GS1
GS0
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0x52, 0x56, 0x5A, 0x5E
Type:
Reset:
0x00
Description:
Enable use of trigger on PWM_n.
[7] RESET: Always read ‘0’
S/W writes ‘1’ to reset counter in WDT mode
Writing ‘1’ in PWM/one-shot has no effect.
Writing ‘0’ has no effect in all modes.
[6] EDGE:type of logic transition to be detected for trigger source.
0: low-to-high
1: hi-to-low
[5] RESERVED
[4] MODE:
0: one-shot trigger mode
1: watch-dog timer mode
This bit is only valid if the ALT bits in the Channel_function_En register is set to ‘1’.
‘1’ for Manual Reload
[3] RELOAD:
‘0’ for Auto-Reload
‘1’ for Manual Reload
[2:0] GS2:0:
Trigger source select
000: GPIO-4
001: GPIO-5
010: GPIO-6
011: GPIO-7
100: GPIO-9
101: GPIO-10
110: GPIO-11
111: GPIO-12
37/61
Basic PWM controller
STMPE1601
PWM_n_SET n=0-3
7
6
PWM_n_Setup n=0-3
5
4
3
2
Brightness
1
0
Timing
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Address:
0x50, 0x54, 0x58, 0x5C
Type:
RW
Reset:
0x00
Description:
PWM blinking control and brightness setting.
[7:4] BRIGTHNESS:
Duty cycle of PWM output during period 0
0000: duty cycle ratio 1:15 ( 6.25%, minimum brightness)
0001: duty cycle ratio 2:14 (12.50%)
0010: duty cycle ratio 3:13 (18.75%)
0011: duty cycle ratio 4:12 (25.00%)
0100: duty cycle ratio 5:11 (31.25%)
0101: duty cycle ratio 6:10 (37.50%)
0110: duty cycle ratio 7: 9 (43.75%)
0111: duty cycle ratio 8: 8 (50.00%)
1000: duty cycle ratio 9: 7 (56.25%)
1001: duty cycle ratio 10: 6 (62.50%)
1010: duty cycle ratio 11: 5 (68.75%)
1011: duty cycle ratio 12: 4 (75.00%)
1100: duty cycle ratio 13: 3 (81.25%)
1101: duty cycle ratio 14: 2 (87.50%)
1110: duty cycle ratio 15: 1 (93.75%)
1111: duty cycle ratio 16: 0 (100.00%, maximum brightness)
38/61
STMPE1601
Basic PWM controller
[3:0] TIMING:
In PWM mode: time unit of each ON or OFF period
In WDT mode: Wait time
In one-short mode: pulse width
0000 = 5 mS
0001 = 10 mS
0010 = 20 mS
0011 = 40 mS
0100 = 80 mS
0101 = 160 mS
0110 = 320 mS
0111 = 640 mS
1000 =
1001 =
1010 =
1011 =
1100 =
1101 =
1110 =
1111 =
1280 mS
2560 mS
5120 mS
10 S
20 S
40 S
80 S
160 S
39/61
Basic PWM controller
STMPE1601
PWM_n_CTRL_n=0-3
7
PWMn control register n=0-3
6
5
4
3
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
Period 0
Period 1
2
Repetition
Address:
0x51, 0x55, 0x59, 0x5D
Type:
R/W
Reset:
0x00
Description:
PWM blinking control register
[7:6] Period 0:
1-4 time units of period 0
Total length of period 0: (period 0 [1:0] + 1) * TIMING
[5:4] Period 1:
0-3 time units of period 1
Total length of period 1: (period 0 [1:0]) * TIMING
[3:2] Repetition:
Number of repetition
0 for Infinite repetition
[1] INT_EN:
“0” to disable interrupt generation on completion of sequence
“1” to enable interrupt generation on completion of sequence
[0] FRAME:
‘0’ will output period 0 first
‘1’ will output period 1 first
40/61
1
0
INT_EN
FRAME
RW
RW
0
0
STMPE1601
11.1
Basic PWM controller
Interrupt on basic PWM controller
A basic PWM controller can be programmed to generate interrupts at the completion of a
blinking sequence. However, there are some limitations:
11.2
a)
Each basic PWM controller has its own bit in the interrupt enable/status registers.
b)
If enabled, completion in any of the PWM controller triggers interrupts. No interrupt
will be generated if infinite repetition is set.
c)
In WDT mode, an interrupt is generated when timeout occurs
d)
In One-shot mode
If Auto-reload, interrupt is generated every time a valid trigger is detected
If Non-auto-reload, an interrupt is generated just once
Trigger feature
The basic PWM controller can be programmed to be controlled by an external “trigger”
signal. This feature can be used to implement:
–
One-shot trigger circuit
–
Watchdog timer
In one-shot trigger mode, a single pulse which the length is defined by TIMING[3:0] is sent
to the PWM output, when a level transition is detected at the trigger source.
In watchdog mode, a 120 μS pulse is generated at PWM output when the programmed timer
has elapsed without getting any trigger for the trigger source.
41/61
Keypad controller
12
STMPE1601
Keypad controller
The keypad controller consists of:
–
4 dedicated key controllers that support up to 4 simultaneous dedicated key
presses;
–
a keyscan controller support a maximum of 8 x 8 key matrix with detection of three
simultaneous key presses;
–
8 special function key controllers that support up to 8 simultaneous “special
function” key presses.
Four of the column inputs can be configured as dedicated keys through the setting of
Dkey0~3 bits of the KPC_CTRL register.
The normal key matrix size can be configured through the setting of KPC_ROW and
KPC_COL registers. The scanning of each individual row output and column input can be
enabled or masked to support a key matrix of variable size from 1 x 1 to 8 x 8. It is allowed
to have other 8 special function keys incorporated in the key matrix.
The operation of the keypad controller is enabled by the SCAN bit of KPC_CTRL register.
Every key activity detected will be de-bounced for a period set by the DB_0~7 bits of
KPC_CTRL register before a key press or key release is confirmed and updated into the
output FIFO. The key data, indicating the key coordinates and its status (up or down), is
loaded into the FIFO at the end of a specified number of scanning cycles (set by
SCAN_COUNT0~3 bits of KPC_ROW_MSB register). An interrupt will be generated when a
new set of key data is loaded. The FIFO has a capacity for ten sets of key data. Each set of
key data consists of 5 bytes of information when any of the four dedicated keys is enabled. It
is reduced to 4 bytes when no dedicated key is involved. When the FIFO is full before its
content is read, an overflow signal will be generated while the FIFO will continue to hold its
content but forbid loading of new key data set.
Figure 8.
Keypad controller
Input 0-7
Keypad Matrix
Output 0-7
The keypad column inputs enabled by the KPC_col register are normally 'high', with the
corresponding input pins pulled up by resistors internally. After reset, all the keypad row
outputs enabled by the KPC_row register are driven 'low'. If a key is pressed, its
42/61
STMPE1601
Keypad controller
corresponding column input will become 'low' after making contact with the 'low' voltage on
its corresponding row output.
Once the keyscan controller senses a 'low' input on any of the column inputs, the scanning
cycles will then start to determine the exact key that has been pressed. The twelve row
outputs will be driven 'low' one by one during each scanning cycle. While one row is driven
'low', all other rows are in tri-state and pulled up. If there is any column input sensed as 'low'
when a row is driven 'low', the key scan controller will then decode the key coordinates (its
corresponding row number and column number), save the key data into a de-bounce buffer
if available, confirm if it is a valid key press after de-bouncing, and update the key data into
output data FIFO if valid.
12.1
Keypad configurations
The keypad controller supports the following types of keys:
●
Up to 8 input * 8 output matrix keys
●
Up to 8 special function keys
●
Up to 4 dedicated keys
Figure 9.
Maximum configuration
Matrix Keypad
(8*8)
STMPE1601
Output 0-7
Input 0-7
Special Function Keys
8*8 (64) Matrix Keys
8 Special Function Keys
0 Dedicated Keys
43/61
Keypad controller
STMPE1601
Figure 10. Maximum configuration
STMPE1601
Output 0-7
Input 0-3
Input 4-7
Dedicated Keys
4*8 (32) Matrix Keys
4 Special Function Keys
4 Dedicated Keys
44/61
Matrix Keypad
(4*8)
Special Function Keys
STMPE1601
12.2
Keypad controller
Registers in keypad controller
Table 24.
Address
Registers in keypad controller
Register name
0x60
KPC_COL
0x61
KPC_ROW_MSB
Description
Keypad column scanning register
Auto-increment
(during sequential R/W)
Yes
Yes
Keypad row scanning register
0x62
KPC_ROW_LSB
0x63
KPC_CTRL_MSB
Yes
Yes
Keypad control register
0x64
KPC_CTRL_LSB
Yes
0x65
KPC_COMBI_KEY_0
Keypad combination key mask 0
Yes
0x66
KPC_COMBI_KEY_1
Keypad combination key mask 1
Yes
0x67
KPC_COMBI_KEY_2
Keypad combination key mask 2
Yes
0x68
KPC_DATA_BYTE0
Yes
0x69
KPC_DATA_BYTE1
Yes
0x6A
KPC_DATA_BYTE2
Keypad data register
Yes
0x6B
KPC_DATA_BYTE3
Yes
0x6C
KPC_DATA_BYTE4
Yes
45/61
Keypad controller
STMPE1601
KPC_COL
Keypad colum register
7
6
5
4
3
2
1
0
RW
RW
RW
RW
0
0
0
RW
RW
RW
RW
0
0
0
0
0
Input Column 0 ~ 7
Address:
0x60
Type:
R/W
Reset:
0x00
Description:
Keypad column scanning
[7] INPUT COLUMN:
1: turn on scanning of column 7
0: turn off
[6] INPUT COLUMN:
1: turn on scanning of column 6
0: turn off
[5] INPUT COLUMN:
1: turn on scanning of column 5
0: turn off
[4] INPUT COLUMN:
1: turn on scanning of column 4
0: turn off
[3] INPUT COLUMN:
1: turn on scanning of column 3
0: turn off
[2] INPUT COLUMN:
1: turn on scanning of column 2
0: turn off
[1] INPUT COLUMN:
1: turn on scanning of column 1
0: turn off
[0] INPUT COLUMN:
1: turn on scanning of column 0
0: turn off
46/61
STMPE1601
Keypad controller
KPC_ROW_MSB
Keypad row MSB
7
6
5
SCAN_PW1
SCAN_PW0
HIB_WK
-
R/W
R/W
R/W
1
1
0
Address:
0x61
Type:
R/W, R
4
3
2
1
0
R
R
R
0
0
R
R
0
0
0
RESERVED
Reset:
Description:
Keypad row scanning register
[7:6] SCAN_PW[1:0]:
Row output scanning pulse width setting:
00: 1x period of internal clock
01: 16x period of internal clock
10: 64x period of internal clock
11: 128x period of internal clock (default)
(This setting is only applicable during normal operation mode. The scanning pulse width is 1x
period of 32 kHz clock during sleep mode.)
[5] HIB_WK:
1: to enable the keypad wake-up from hibernate mode
0: to disable
[4:0] RESERVED
47/61
Keypad controller
STMPE1601
KPC_ROW_lsb
Keypad controller row (LSB)
7
6
5
4
R/W
R/W
R/W
R/W
0
0
0
0
3
2
1
0
R/W
R/W
R/W
R/W
0
0
0
0
1
0
OUTPUT ROW 0 ~ 7
Address:
0x62
Type:
Reset:
0x00
Description:
Keypad row scanning register.
[7:0] OUTPUT ROW 0 ~ 7:
‘1’ to turn on scanning of the corresponding row;
‘0’ to turn off
KPC_CTRL_msb
7
6
Keypad controller control (MSB)
5
4
3
2
SCAN_COUNT_0 ~ 3
DKEYy_0 ~ 3
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Address:
0x63
Type:
R/W
Reset:
0x00
Description:
Keypad control register.
[7:4] SCAN_COUNT_0~ 3:
Number of key scanning cycles elapsed before a confirmed key data is updated into output
data FIFO (0 ~ 15 cycles)
[3] DKEY_3:
Set ‘1’ to use input column 3 as dedicated key
[2] DKEY_2:
Set ‘1’ to use input column 2 as dedicated key
[1] DKEY_1:
Set ‘1’ to use input column 1 as dedicated key
[0] DKEY_0:
Set ‘1’ to use input column 0 as dedicated key
48/61
STMPE1601
Keypad controller
KPC_CTRL_lsb
Keypad controller control (LSB)
7
6
5
R/W
R/W
R/W
0
0
0
4
3
2
1
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
DB[6:0]
Address:
0x64
Type:
R/W
Reset:
0x00
Description:
Keypad control register.
0
SCAN
[7:1] DB_6:0:
0-128 ms of de-bounce time
[0] SCAN:
1: to start scanning
0: to stop
49/61
Data registers
13
STMPE1601
Data registers
The KPC_DATA register contains three bytes of information. The first two bytes store the key
coordinates and status of any two keys from the normal key matrix, while the third byte store
the status of dedicated keys.
KPC_DATA_BYTE0
Keypad data byte 0
7
6
5
4
3
2
1
0
UP/DOWN
R3
R2
R1
R0
C2
C1
C0
R
R
R
R
R
R
R
R
1
1
1
1
1
0
0
0
Address:
0x68
Type:
R
Reset:
0xF8
Description:
Keypad data register.
[7] UP/DOWN:
0: key-down
1: key-up
[6:3] R[3:0]
Row number of key 1 (valid range: 0-7)
0x1111: No Key
[2:0] C[2:0}:
Column number of key 1 (valid range: 0-7)
50/61
STMPE1601
Data registers
KPC_DATA_BYTE1
Keypad data byte 1
7
6
5
4
3
2
1
0
Up/Down
R3
R2
R1
R0
C2
C1
C0
R
R
R
R
R
R
R
R
1
1
1
1
1
0
0
0
Address:
0x69
Type:
R
Reset:
0xF8
Description:
Keypad data register.
[7] UP/DOWN:
0: key-down
1: key-up
[6:3] R[3:0]
Row number of key 2 (valid range: 0-7)
0x1111: No key
[2:0] C[2:0}:
Column number of key 1 (valid range: 0-7)
51/61
Data registers
STMPE1601
KPC_DATA_BYTE2
Keypad data byte 2
7
6
5
4
3
2
1
0
UP/DOWN
R3
R2
R1
R0
C2
C1
C0
R
R
R
R
R
R
R
R
1
1
1
1
1
0
0
0
Address:
0x6A
Type:
R
Reset:
0xF8
Description:
Keypad data register.
[7] UP/DOWN:
0: key-down
1: key-up
[6:3] R[3:0]
Row number of key 3 (valid range: 0 - 7)
0x1111: No key
[2:0] C[2:0}:
column number of key 3 (valid range: 0 -7)
52/61
STMPE1601
Data registers
KPC_DATA_BYTE3
Keypad data byte 3
7
6
5
4
3
2
1
0
SF7
SF6
SF5
SF4
SF3
SF2
SF1
SF0
R
R
R
R
R
R
R
R
1
1
1
1
1
1
1
1
2
1
0
Address:
0x6B
Type:
R
Reset:
0xFF
Description:
Keypad data register.
[7:0] SF[7:0]:
0: key-down
1: key-up
KPC_DATA_BYTE4
7
6
Keypad data byte 4
5
4
3
RESERVED
Dedicated Key 0 ~ 3
R
R
R
R
R
R
R
R
0
0
0
0
1
1
1
1
Address:
0x6C
Type:
R
Reset:
Description:
Keypad data register.
[7:4] RESERVED:
[3:0] Dedicated key [3:0]:
0: key-down
1 key-up
53/61
Keypad combination key registers
14
STMPE1601
Keypad combination key registers
The 3 KPC mask registers contains the key combination to be used to wake up the KPC and
send an interrupt to the host system.
KPC_COMB_KEY_0-2
Keypad combination 0-2
7
6
5
4
3
2
1
0
ACTIVE
ACTIVE
R2
R1
R0
C2
C1
C0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
1
1
1
1
1
0
0
0
Address:
0x65, 0x66, 0x67
Type:
R/W
Reset:
0xF8
Description:
Keypad combination key mask registers.
[7:6] ACTIVE:
00: key defined by bits 5:0 to be used for combination key wakeup
But [7:0] must be “F8” for No key from this register to be used for combination key wakeup
[5:3] R[2:0]:
Row number of key 1 (valid range: 0 -7)
[2:0] C[2:0]:
Column number of key 1 (valid range : 0-7)
54/61
STMPE1601
Keypad combination key registers
Resistance
The maximum resistance between keypad outputs and inputs, inclusive of switch resistance,
protection circuit resistance and connection, must be less than 3.2 KΩ
Using the keypad controller
It is not necessary to explicitly enable the internal pull-up and direction by configuring the
GPIO control registers. Once a GPIO is enabled for the keypad function, its internal pull-up
and direction is controlled automatically.
The scanning of column inputs should then be enabled for those GPIO ports that are
configured as keypad inputs by writing '1's to the corresponding bits in the KPC_COL
register. If any of the first three column inputs is to be used as dedicated key input, the
corresponding bits in the KPC_CTRL_MSB register should be set to '1'. The bits in the
KPC_ROW_MSB and KPC_ROW_LSB registers should also be set correctly to enable the
row output scanning for the corresponding GPIO ports programmed as keypad outputs.
The scan count and de-bounce count should also be programmed into the keypad control
registers before enabling the keypad controller operation. To enable the keypad controller
operation, the EN_KPC bit in the system control register must be set to '1' to provide the
required clock signals. The keypad controller will then start its operation by setting the
SCAN bit in the KPC_CTRL_LSB register to '1'.
The keypad controller operation can be disabled by setting the SCAN bit back to '0'. To
further reduce the power consumption, the clock signals can be cut off from the keypad
controller by setting the EN_KPC bit to '0'.
As long as there is any un-read key-press in the keypad controller buffer, the KPC interrupt
will always be asserted.
Ghost key handling
The ghost key is an inherent in keypad matrix that is not equipped with a diode at each of
the keys. While it is not possible to avoid ghost key occurrence, the STMPE1601 allows the
detection of possible ghost keys by the capability of detecting 3 simultaneous key-presses in
the key matrix.
The ghost key is only possible if 3 keys are pressed and held down together in a keypad
matrix. If 3 keys are reported by the STMPE1601 keypad controller, it indicates a potential
ghost key situation. The system may check for the possibility of a ghost key by analyzing the
coordinates of the 3 keys. If the 3 keys form 3 corners of a rectangle, it could be a ghost key
situation.
A ghost key may also occur in the “special function keys”. The keypad controller does not
attempt to avoid the occurrence of ghost keys. However, the system should be aware that if
more than one special function key is reported, then there is a possibility of ghost keys.
Key detection priority
A dedicated key is always detected, if this is enabled. When a special function key is
detected, the matrix key scanning on the same input line is disabled.
Up to 3 matrix keys can be detected. Matrix keys that fall on activated special function keys
will not be counted.
As a result of these priority rules, a matrix key is ignored by the keypad controller when the
special function key on the same input line is detected, even if the matrix key is being
55/61
Keypad combination key registers
STMPE1601
pressed down before the special function key. Hence, when a matrix is reported "key-down"
and it is being held down while the corresponding special function is being pressed, a "nokey" status will be reported for the matrix key when the special function key is reported "keydown". If the matrix key is released while the special function key is still being held down, no
"key-up" will be reported for the matrix key. On the other hand, if the matrix key is released
after the special function key is reported "key-up", then a new "key-down" will be reported for
the matrix key, followed by "key-up".
Keypad wakeup from sleep and hibernate modes
The keypad controller is functional in sleep mode as long as it is enabled before entering the
sleep mode. It will then wake the system up into operational mode if a valid key press is
detected.
In the case of hibernate mode, the 'HIB_WK' bit in 'KPC_ROW_msb' register must be set to
'1' in order to enable the system wakeup by means of a valid key press. When this is
enabled, an asynchronous detection of the keypad column input activity is turned on during
the hibernate mode. If any key activity is detected, the system is expected to enter the sleep
mode temporarily to allow a debouncing of key press to take place. If a valid key is detected,
the system will then wake up into operational mode; otherwise, the device will go back into
hibernate mode.
Keypad controller combination-Key interrupt
The keypad controller (KPC) can be programmed to wake up from sleep mode if a unique
combination keys is detected. This combination keys of up to 3 keys is specified in the KPC
combination set 0-2 registers. Note that the sequence of the key press is not relevant, as
long as the 1-3 keys specified in the KPC_CombiKey are detected, the KPC will wake up
and interrupt the host.
If any other keys (beside those specified in the KPC_CombiKey registers) are pressed, it
would be considered invalid combination and interrupt will NOT be generated.
All the "active" keys must be pressed and held together, for the combi-key interrupt to be
generated.
56/61
STMPE1601
Miscellaneous features
15
Miscellaneous features
15.1
Reset
The STMPE1601 is equipped with an internal POR circuit that holds the device in reset
state, until the clock is steady and VCC input is valid. The host system may choose to reset
the STMPE1601 by asserting the RESET_N pin.
15.2
Under voltage lockout
The STMPE1601 is equipped with an internal UVLO (under voltage lockout) circuit that
generates a RESET signal, when the main supply voltage falls below the allowed threshold.
57/61
Package mechanical data
16
STMPE1601
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect . The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com
Figure 11. TFBGA25 package outline
Table 25.
TFBGA25 mechanical data
mm.
inch
Dim.
A
Min
Typ
Max
Min
Typ
Max
1.0
1.1
1.16
39.4
43.3
45.7
A1
0.25
A2
0.78
b
0.25
D
2.9
D1
E
E1
58/61
9.8
0.86
30.7
0.30
0.35
9.8
11.8
13.8
3.0
3.1
114.2
118.1
122.0
2
2.9
3.0
33.9
78.8
3.1
114.2
118.1
2
78.8
e
0.5
19.7
SE
0.25
9.8
122.0
STMPE1601
Package mechanical data
Figure 12. Tape and reel dimension
Table 26.
TFBGA25 tape and reel mechanical data
millimeters
inches
Symbol
Min
Typ
A
Max
Min
Typ
330
13.2
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
Max
0.504
0.519
14.4
0.567
Ao
3.3
0.130
Bo
3.3
0.130
Ko
1.60
0.063
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
59/61
Revision history
17
STMPE1601
Revision history
Table 27.
Document revision history
Date
Revision
10-Jan-2008
1
Initial release.
15-Feb-2008
2
Modified Figure 1 on page 4, added info on register Description: on
page 40 and Section 6.1: Minimizing current drain on I2C address
lines on page 13, updated Table 7: DC electrical characteristics on
page 9, minor text changes.
14-Mar-2008
3
Updated Table 7: DC electrical characteristics on page 9
4
Document status promoted from preliminary data to datasheet.
Modified: Figure 1 on page 4, Rup values in Table 10, Channel
function enabling and PWM trigger register n = 0 - 3 registers.
Updated: Section 6: I2C interface, Section 7: System controller,
Section 9: Interrupt system, Section 10: GPIO controller, Section 11:
Basic PWM controller, Section 12: Keypad controller
02-June-2008
60/61
Changes
STMPE1601
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
61/61