STMICROELECTRONICS STTH8R06DIRG

STTH8R06
Turbo 2 ultrafast high voltage rectifier
Features
■
Ultrafast switching
■
Low reverse recovery current
■
Low thermal resistance
■
Reduces switching losses
■
Package insulation voltage:
TO-220AC Ins: 2500 V rms
TO-220FPAC: 2000 V dc
K
K
TO-220AC
STTH8R06D
A
A
K
TO-220FPAC
STTH8R06FP
K
K
Description
The STTH8R06, which uses ST Turbo 2 600 V
technology, is specially suited as boost diode in
continuous mode power factor corrections and
hard switching conditions.
A
A
NC
D2PAK
STTH8R06G
K
NC
I2PAK
STTH8R06R
K
A
TO-220AC Insulated
STTH8R06DIRG
Table 1.
April 2008
Rev 6
Device summary
IF(AV)
8A
VRRM
600 V
IRM (typ)
5.5 A
Tj
175°C
VF (typ)
1.4 V
trr (max)
25 ns
1/12
www.st.com
12
Characteristics
STTH8R06
1
Characteristics
Table 2.
Absolute ratings (limiting values)
Symbol
VRRM
Parameter
IF(AV)
30
TO-220AC Ins.
24
A
Average forward current
δ = 0.5
TO-220AC / D2PAK / I2PAK
Tc = 130 °C
TO-220FPAC
Tc = 85 °C
TO-220AC Ins.
Tc = 100 °C
Tstg
Storage temperature range
Table 4.
Symbol
8
A
80
A
-65 to + 175
°C
175
°C
tp = 10ms sinusoidal
Maximum operating junction temperature
Thermal resistance
Symbol
Rth(j-c)
V
TO-220AC / TO-220FPAC / D PAK / I PAK
Surge non repetitive forward current
Table 3.
600
2
Forward current rms
IFSM
Tj
Unit
Repetitive peak reverse voltage
2
IF(RMS)
Value
Parameter
Junction to case
Value (max)
TO-220AC / D2PAK / I2PAK
2.2
TO-220FPAC
4.6
TO-220AC Ins.
3.8
Unit
°C/W
Static electrical characteristics
Parameter
IR
Reverse leakage current
VF
Forward voltage drop
Test conditions
Tj = 25 °C
Tj = 125 °C
Tj = 25 °C
Tj = 125 °C
Min
Typ
Max
Unit
30
VR = VRRM
µA
35
400
2.9
IF = 8 A
V
1.4
1.8
To evaluate the conduction losses use the following equation: P = 1.16 x IF(AV) + 0.08 IF2(RMS)
Table 5.
Symbol
trr
IRM
Dynamic characteristics
Parameter
Reverse recovery time
tfr
VFP
2/12
Tj = 25 °C
Typ Max Unit
25
IF = 1 A, dIF/dt = -50 A/µs, VR = 30 V
45
ns
5.5
I = 8 A, VR = 400 V,
Tj = 125 °C F
dIF/dt = -200 A/µs
Reverse recovery charges
7.2
Tj = 25°C
IF = 8 A, dIF/dt = 64 A/µs
VFR = 1.1 x VFmax
A
0.3
150
Forward recovery time
Forward recovery voltage
Min
IF = 0.5 A, Irr = 0.25 A, IR =1 A
Reverse recovery current
S factor Softness factor
Qrr
Test conditions
nC
150
ns
5
V
STTH8R06
Figure 1.
Characteristics
Conduction losses versus
average current
Figure 2.
Forward voltage drop versus
forward current
IFM(A)
P(W)
100
24
22
δ = 0.05
20
δ = 0.1
Tj=125°C
(maximum values)
90
δ = 0.2
δ = 0.5
80
18
70
16
δ=1
14
Tj=125°C
(typical values)
60
12
50
10
40
8
Tj= 25°C
(maximum values)
30
6
T
20
4
2
IF(AV)(A)
0
2
4
10
δ=tp/T
0
6
VFM(V)
tp
0
8
10
0
Figure 4.
Relative variation of thermal
impedance junction to case versus
pulse duration (TO-220AC, I2PAK,
D2PAK)
Figure 3.
1
2
3
4
5
6
7
Relative variation of thermal
impedance junction to case versus
pulse duration
(TO-220FPAC Insulated)
Zth(j-c)/Rth(j-c)
Zth(j-c)/Rth(j-c)
1.0
1.0
0.9
0.9
0.8
0.8
0.7
0.7
0.6
0.6
0.5
0.5
0.4
0.4
0.3
0.3
Single pulse
T
T
0.2
0.1
tp(s)
δ=tp/T
0.0
1.E-03
Figure 5.
1.E-02
1.E-01
0.2
0.1
δ=tp/T
0.0
1.E+00
Peak reverse recovery current
versus dIF/dt (typical values)
1.E-03
Figure 6.
1.E-02
1.E-01
tp
1.E+00
1.E+01
Reverse recovery time versus
dIF/dt (typical values)
trr(ns)
120
VR=400V
Tj=125°C
20
tp(s)
tp
IRM(A)
22
Single pulse
VR=400V
Tj=125°C
110
IF=2 x IF(AV)
100
18
90
IF=IF(AV)
16
80
14
IF=0.5 x IF(AV)
70
12
IF=2 x IF(AV)
60
10
50
IF=0.25 x IF(AV)
IF=IF(AV)
IF=0.5 x IF(AV)
8
40
6
30
4
20
2
10
dIF/dt(A/µs)
0
dIF/dt(A/µs)
0
0
200
400
600
800
1000
0
200
400
600
800
1000
3/12
Characteristics
Figure 7.
STTH8R06
Reverse recovery charges
versus dIF/dt (typical values)
Figure 8.
Qrr(nC)
Softness factor versus
dIF/dt (typical values)
S factor
350
0.70
VR=400V
Tj=125°C
IF≤2 x IF(AV)
VR=400V
Tj=125°C
0.65
300
0.60
IF=2 x IF(AV)
0.55
250
0.50
IF=IF(AV)
0.45
200
IF=0.5 x IF(AV)
0.40
150
0.35
0.30
100
0.25
0.20
50
0.15
dIF/dt(A/µs)
dIF/dt(A/µs)
0.10
0
0
Figure 9.
200
400
600
800
0
1000
Relative variations of dynamic
parameters versus junction
temperature
200
400
600
800
1000
Figure 10. Transient peak forward voltage
versus dIF/dt (typical values)
VFP(V)
2.50
12
2.25
10
9
S factor
1.75
IF=IF(AV)
Tj=125°C
11
IF=IF(AV)
VR=400V
Reference: Tj=125°C
2.00
8
1.50
7
1.25
6
1.00
5
IRM
0.75
4
0.50
3
QRR
2
0.25
Tj(°C)
1
0.00
25
50
75
100
125
dIF/dt(A/µs)
0
0
4/12
100
200
300
400
500
STTH8R06
Characteristics
Figure 11. Forward recovery time versus
dIF/dt (typical values)
Figure 12. Junction capacitance versus
reverse voltage applied
(typical values)
tfr(ns)
C(pF)
160
100
IF=IF(AV)
VFR=1.1 x VF max.
Tj=125°C
140
F=1MHz
VOSC=30mVRMS
Tj=25°C
120
100
80
60
40
20
dIF/dt(A/µs)
VR(V)
10
0
0
100
200
300
400
500
1
10
100
1000
Figure 13. Thermal resistance junction to
ambient versus copper surface
under tab (epoxy FR4, eCU = 35 µm)
(D2PAK)
Rth(j-a)(°C/W)
70
60
50
40
30
20
10
S(Cu)(cm²)
0
0
5
10
15
20
25
30
35
40
5/12
Package information
2
STTH8R06
Package information
●
Epoxy meets UL94, V0
●
Cooling method: by conduction (C)
●
Recommended torque values: 0.8 to 1.0 N·m (TO-220FPAC),
0.4 to 0.6 N·m to (TO-220AC)
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at www.st.com.
Table 6.
TO-220AC dimensions
Dimensions
Ref.
Inches
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
C
1.23
1.32
0.048
0.051
D
2.40
2.72
0.094
0.107
E
0.49
0.70
0.019
0.027
F
0.61
0.88
0.024
0.034
F1
1.14
1.70
0.044
0.066
G
4.95
5.15
0.194
0.202
H2
10.00
10.40
0.393
0.409
A
H2
ØI
C
L5
L7
L6
L2
F1
Millimeters
D
L9
L2
L4
F
M
16.40 typ.
0.645 typ.
L4
13.00
14.00
0.511
0.551
L5
2.65
2.95
0.104
0.116
L6
15.25
15.75
0.600
0.620
L7
6.20
6.60
0.244
0.259
L9
3.50
3.93
0.137
0.154
E
G
M
Diam. I
6/12
2.6 typ.
3.75
3.85
0.102 typ.
0.147
0.151
STTH8R06
Package information
Table 7.
TO-220FPAC dimensions
Dimensions
Ref.
A
Millimeters
Inches
Min.
Max.
Min.
Max.
A
4.4
4.6
0.173
0.181
B
2.5
2.7
0.098
0.106
D
2.5
2.75
0.098
0.108
E
0.45
0.70
0.018
0.027
F
0.75
1
0.030
0.039
F1
1.15
1.70
0.045
0.067
G
4.95
5.20
0.195
0.205
G1
2.4
2.7
0.094
0.106
H
10
10.4
0.393
0.409
B
H
Dia
L6
L7
L2
L3
L5
F1
D
L2
L4
F
G1
G
E
16 Typ.
0.63 Typ.
L3
28.6
30.6
1.126
1.205
L4
9.8
10.6
0.386
0.417
L5
2.9
3.6
0.114
0.142
L6
15.9
16.4
0.626
0.646
L7
9.00
9.30
0.354
0.366
Dia.
3.00
3.20
0.118
0.126
7/12
Package information
Table 8.
STTH8R06
TO-220AC (nIns. and ins. 20-up) dimensions
Dimensions
Ref.
Millimeters
Min.
A
ØI
15.20
a1
C
B
b2
L
Typ.
Max.
Inches
Min.
Typ.
15.90 0.598
3.75
Max.
0.625
0.147
a2
13.00
14.00 0.511
0.551
B
10.00
10.40 0.393
0.409
b1
0.61
0.88 0.024
0.034
b2
1.23
1.32 0.048
0.051
C
4.40
4.60 0.173
0.181
c1
0.49
0.70 0.019
0.027
c2
2.40
2.72 0.094
0.107
e
4.80
5.40 0.189
0.212
F
6.20
6.60 0.244
0.259
ØI
3.75
3.85 0.147
0.151
I4
15.80 16.40 16.80 0.622 0.646 0.661
L
2.65
2.95 0.104
0.116
l2
1.14
1.70 0.044
0.066
F
A
I4
c2
a1
l2
a2
M
b1
e
c1
M
8/12
2.60
0.102
STTH8R06
Package information
I2PAK dimensions
Table 9.
Dimensions
Ref.
A
E
c2
L2
D
L1
A1
b1
L
b
c
Millimeters
Inches
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
A1
2.40
2.72
0.094
0.107
b
0.61
0.88
0.024
0.035
b1
1.14
1.70
0.044
0.067
c
0.49
0.70
0.019
0.028
c2
1.23
1.32
0.048
0.052
D
8.95
9.35
0.352
0.368
e
2.40
2.70
0.094
0.106
e1
4.95
5.15
0.195
0.203
E
10
10.40
0.394
0.409
L
13
14
0.512
0.551
L1
3.50
3.93
0.138
0.155
L2
1.27
1.40
0.050
0.055
e
e1
9/12
Package information
Table 10.
STTH8R06
D2PAK dimensions
Dimensions
Ref.
A
E
C2
L2
D
L
L3
A1
B2
R
C
B
G
A2
M
*
V2
* FLAT ZONE NO LESS THAN 2mm
Millimeters
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
A1
2.49
2.69
0.098
0.106
A2
0.03
0.23
0.001
0.009
B
0.70
0.93
0.027
0.037
B2
1.14
1.70
0.045
0.067
C
0.45
0.60
0.017
0.024
C2
1.23
1.36
0.048
0.054
D
8.95
9.35
0.352
0.368
E
10.00
10.40
0.393
0.409
G
4.88
5.28
0.192
0.208
L
15.00
15.85
0.590
0.624
L2
1.27
1.40
0.050
0.055
L3
1.40
1.75
0.055
0.069
M
2.40
3.20
0.094
0.126
R
V2
0.40 typ.
0°
8°
Figure 14. D2PAK footprint (dimensions in mm)
16.90
10.30
5.08
1.30
8.90
10/12
Inches
3.70
0.016 typ.
0°
8°
STTH8R06
3
Ordering information
Ordering information
Table 11.
Ordering information
Ordering type
Marking
Package
Weight
Base qty
Delivery mode
STTH8R06D
STTH8R06D
TO-220AC
1.90 g
50
Tube
STTH8R06G
2
D PAK
1.48 g
50
Tube
STTH8R06G-TR
STTH8R06G
D2
1.48 g
1000
Tape and reel
STTH8R06FP
STTH8R06FP
1.70 g
50
Tube
1.5 g
50
Tube
1.86 g
50
Tube
STTH8R06G
4
STTH8R06R
STTH8R06R
STTH8R06DIRG
STTH8R06DI
PAK
TO-220FPAC
I2
PAK
TO-220AC Ins.
Revision history
Table 12.
Document revision history
Date
Revision
May-2001
1
First issue
January-2002
2
D2PAK and I2PAK packages added
18-Oct-2004
3
TO-220AC Insulated package added
05-Dec-2004
4
D2PAK foot print correction
10-Aug-2006
5
Reformatted to current standard. Added package insulation voltage
data on page 1. Changed order code STTH8R06DI to
STTH8R06DIRG.
6
Reformatted to current standards. Corrected label for right hand
curve in Figure 2 from Tj = 125 °C to Tj = 25 °C. Updated torque
value recomendations and added ECOPACK statement in Section 2:
Package information. Corrected order code in Table 11.
16-Apr-2008
Changes
11/12
STTH8R06
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
12/12