STMICROELECTRONICS TSM1052_08

TSM1052
Constant voltage and constant current controller
for battery chargers and adapters
Features
■
Secondary-side constant voltage and constant
current control
■
Very low voltage operation
■
Very low quiescent consumption
■
High-accuracy internal reference
■
Low external component count
■
Wired-or open-drain output stage
■
Easy frequency compensation
■
SOT23-6 micro package
SOT23-6
Applications
■
Battery chargers
■
AC DC adapters
The external components needed to complete the
two control loops are:
■
A resistor divider that senses the output of the
power supply (adapter, battery charger) and
fixes the voltage regulation set point at the
specified value;
■
The TSM1052 integrates a voltage reference, two
op amps (with OR-ed open-drain outputs), and a
low-side current sensing circuit.
A sense resistor that feeds the current sensing
circuit with a voltage proportional to the dc
output current; this resistor determines the
current regulation set point and must be
adequately rated in terms of power dissipation;
■
The voltage reference, along with one op amp, is
the core of the voltage control loop; the current
sensing circuit and the other op amp make up the
current control loop.
Frequency compensation components
(RC networks) for both loops.
The TSM1052, housed in one of the smallest
package available, is ideal for space-shrunk
applications such as adapters and chargers.
Description
The TSM1052 is a highly integrated solution for
SMPS applications requiring a dual control loop to
perform CV (constant voltage) and CC (constant
current) regulation.
Table 1.
Device summary
Part number
Package
Packaging
TSM1052
SOT23-6
Tape and reel
February 2008
Rev 2
1/15
www.st.com
15
Contents
TSM1052
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3
Internal schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1
Typical application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2
Voltage and current control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.1
Voltage control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.2
Current control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3
Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.4
Start up and short circuit conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5
Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2/15
TSM1052
Description
1
Description
1.1
Pin connection
Figure 1.
1.2
Pin Connection (top view)
Vctrl
1
6
Vcc
GND
2
5
Vsense
OUT
3
4
Ictrl
Pin description
Table 2.
Pin description
N.
Name
Function
1
Vctrl
Inverting input of the voltage loop op amp. The pin will be tied to the mid-point
of a resistor divider that senses the output voltage.
2
GND
Ground. Return of the bias current of the device. 0 V reference for all
voltages. The pin should be tied as close to the ground output terminal of the
converter as possible to minimize load current effect on the voltage regulation
set point.
3
OUT
Common open-drain output of the two internal op amps. The pin, able to sink
current only, will be connected to the branch of the optocoupler’s photodiode
to transmit the error signal to the primary side.
4
Ictrl
Non-inverting input of the current loop op amp. It will be tied directly to the hot
(negative) end of the current sense resistor
5
Vsense
Inverting input of the current loop op amp. The pin will be tied to the cold end
of the current sense resistor through a decoupling resistor.
6
Vcc
Supply Voltage of the device. A small bypass capacitor (0.1 µF typ.) to GND,
located as close to IC’s pins as possible, might be useful to get a clean
supply voltage.
3/15
Description
1.3
TSM1052
Internal schematic
Figure 2.
Internal schematic
Vcc
6
1.21
V V
1.238
+
+
3
OUT
1
Vctrl
2
GND
-
+
200 mV
-
1.4
5
Ictrl
Vsense
Absolute maximum ratings
Table 3.
1.5
4
Absolute maximum ratings
Symbol
Pin
VCC
6
VOUT
Parameter
Value
Unit
DC supply voltage
-0.3 to 20
V
3
Open-drain voltage
-0.3 to VCC
V
IOUT
3
Max sink current
100
mA
V
1, 4, 5
-0.3 to 3.3
V
Value
Unit
250
°C/W
Analog inputs
Thermal data
Table 4.
Thermal data
Symbol
4/15
Parameter
RthJA
Thermal resistance, junction-to-ambient
TOP
Junction temperature operating range
Tjmax
Maximum junction temperature
TSTG
Storage temperature
-10 to 85
150
-55 to 150
°C
TSM1052
2
Electrical characteristics
Electrical characteristics
TJ = 25 °C and VCC = 5 V, unless otherwise specified
Table 5.
Electrical characteristics
Symbol
Parameter
Test conditions
Min
Typ
Max
Unit
18
V
Device supply
VCC
Voltage operating range
ICC
Quiescent current
(Ictrl = Vsense = Vctr = 0,
OUT = open)
1.7
150
µA
(1)
300
Voltage control loop op amp
Gmv
Transconductance
(sink current only) (2)
Vref
Voltage reference (3)
1
S
(1)
2.5
1.198
(1)
3.5
1.21
1.222
V
1.186
1.234
50
Ibias
Inverting input bias current
nA
(1)
100
Current control loop
Gmi
Vsense
Ibias
1.5
Transconductance
(sink current only) (4)
(1)
Current loop reference (5)
@ I(Iout) = 1 mA
(1)
Non-inverting input source current @
V(Ictrl) = -200 mV
(1)
7
S
196
200
204
mV
192
208
20
µA
40
Output stage
100
VOUTlow Low output level @ 2 mA sink current
(1)
mV
200
1. Specification referred to -10 °C < TA < 85 °C
2. If the voltage on Vctrl (the negative input of the amplifier) is higher than the positive amplifier input
(Vref = 1.21 V), and it is increased by 1mV, the sinking current at the output OUT will be increased by
3.5 mA.
3. The internal Voltage Reference is set at 1.21 V (bandgap reference). The voltage control loop precision
takes into account the cumulative effects of the internal voltage reference deviation as well as the input
offset voltage of the transconductance operational amplifier. The internal Voltage Reference is fixed by
bandgap, and trimmed to 0.5% accuracy at room temperature.
4. When the positive input at Ictrl is lower than -200 mV, and the voltage is decreased by 1mV, the sinking
current at the output Out will be increased by 7 mA.
5. The internal current sense threshold is set at -200 mV. The current control loop precision takes into
account the cumulative effects of the internal voltage reference deviation as well as the input offset voltage
of the transconductance operational amplifier.
5/15
Typical characteristics
TSM1052
3
Typical characteristics
Figure 3.
Vref vs ambient temperature
Vcc=18V
Vcc=5V
Figure 4.
Vcc=18V
Vcc=1.7V
1.230
Vsense (mV)
Vref (V)
1.220
1.210
1.200
1.190
-20
0
20
40
VSENSE vs ambient temperature
60
80
-20
100
0
20
Vcc=18V
50
15
40
14
30
13
20
80
100
Vcc=5V
Vcc=1.7V
12
11
0
10
-20
0
20
40
60
80
100
-20
0
20
Temp ( °C )
Figure 7.
40
60
80
100
Temp ( °C )
Transconductances (sink current
Figure 8.
only) of voltage control loop op amp
vs ambient temperature
Vcc=18V
Vcc=5V
Transconductance (sink current
only) of current control loop op amp
vs ambient temperature
Vcc=18V
Vcc=1.7V
Vcc=5V
Vcc=1.7V
20
18
16
14
12
10
8
6
4
2
0
Gmi(mA/mV)
Gmv(mA/mV)
60
ICTRL pin input bias current vs
ambient temperature
Vcc=1.7V
Iibi(uA)
Iibv(nA)
Vcc=5V
Figure 6.
10
15
10
5
0
-20
0
20
40
Temp ( °C )
6/15
40
Temp ( °C )
VSENSE pin input bias current vs
ambient temperature
Vcc=18V
Vcc=1.7V
208
206
204
202
200
198
196
194
192
Temp ( °C )
Figure 5.
Vcc=5V
60
80
100
-20
0
20
40
Temp ( °C )
60
80
100
TSM1052
Figure 9.
Typical characteristics
Low output level of voltage control
loop op amp vs ambient
temperature (2 mA sink current)
Vcc=18V
Vcc=5V
Figure 10. Low output level of current control
loop op amp vs ambient
temperature (2 mA sink current)
Vcc=1.7V
Vcc=18V
120
80
Volc(mV)
Volv(mV)
100
60
40
20
0
-20
0
20
40
60
80
-20
100
0
20
Iosv(mA)
Vcc=5V
Vcc=1.7V
Vcc=18V
Iosc(mA)
20
40
60
80
100
100
Vcc=5V
Vcc=1.7V
-20
0
20
40
60
80
100
Temp ( °C )
Figure 13. Supply current vs ambient
temperature
Vcc=5V
Figure 14. Low output level vs sink current
Vcc=1.7V
2.5
0.350
0.300
0.250
0.200
0.150
0.100
0.050
0.000
2
Vol (V)
Icc(uA)
80
80
70
60
50
40
30
20
10
0
Temp ( °C )
Vcc=18V
60
Figure 12. Output short circuit current of
current control loop op amp vs
ambient temperature
70
60
50
40
30
20
10
0
0
40
Temp ( °C )
Figure 11. Output short circuit current of
voltage control loop op amp vs
ambient temperature
-20
Vcc=1.7V
140
120
100
80
60
40
20
0
Temp ( °C )
Vcc=18V
Vcc=5V
1.5
1
0.5
0
-20
0
20
40
Temp ( °C )
60
80
100
1
6
11
16
21
26
31
Isink (mA)
7/15
Application information
TSM1052
4
Application information
4.1
Typical application schematic
Figure 15. Typical adapter or battery charger application using the device
Vcc
TSM1052
1.210 V
+
R1
6
Rled
+
3
OUT
-
200 mV
Cvc1
1
+
Rvc1
Vctrl
Vout
Cic1
2
4
5
Ictrl
Vsense
GND
Ric1
R2
Ric2
Rsense
Iout
In the above application schematic, the device is used on the secondary side of a flyback
adapter (or battery charger) to provide an accurate control of voltage and current. The
above feedback loop is made with an optocoupler.
4.2
Voltage and current control
4.2.1
Voltage control
The voltage loop is controlled via a first transconductance operational amplifier, the voltage
divider R1, R2, and the optocoupler which is directly connected to the output. Its possible to
choose the values of R1 and R2 resistors using Equation 1:
Equation 1
a)
Vout = Vref ⋅
b)
R1 = R2 ⋅
(R1 + R 2 )
R2
(Vout − Vref )
Vref
where Vout is the desired output voltage.
As an example, with R1 = 100 kΩ and R2 = 27 kΩ, VOUT = 5.7 V
8/15
TSM1052
4.2.2
Application information
Current control
The current loop is controlled via the second trans-conductance operational amplifier, the
sense resistor Rsense, and the optocoupler. The control equation verifies:
Equation 2
a)
R sense ⋅ Ilim = Vsense
b)
R sense =
Vsense
Ilim
where Ilim is the desired limited current, and VSENSE is the threshold voltage for the current
control loop.
As an example, with Ilim = 1 A, VSENSE = 200 mV, then RSENSE = 200 mΩ.
Note:
The Rsense resistor should be chosen taking into account the maximum dissipation (Plim)
through it during full load operation.
Equation 3
Plim = Vsense ⋅ Ilim
As an example, with Ilim = 1 A, and Vsense = 200 mV, Plim = 200 mW.
Therefore, for most adapter and battery charger applications, a quarter-watt, or half-watt
resistor is sufficient. VSENSE threshold is made internally by a voltage divider tied to the Vref
voltage reference. Its middle point is tied to the positive input of the current control
operational amplifier, and its foot is to be connected to lower potential point of the sense
resistor as shown in Figure 15 on page 8. The resistors of this voltage divider are matched
to provide the best possible accuracy. The current sinking outputs of the two
transconductance operational amplifiers are common (to the output of the IC). This makes
an ORing function which ensures either the voltage control or the current control, driving the
optocoupler's photodiode to transmit the feedback to the primary side.
The relation between the controlled current and the controlled output voltage can be
described with a square characteristic as shown in the following V/I output-power diagram.
(with the power supply of the device indipendent of the output voltage)
9/15
Application information
TSM1052
Figure 16. Output voltage versus output current
Vout
Voltage regulation
Current regulation
(Vcc of the device independent of output voltage)
4.3
Iout
Compensation
The voltage control transconductance operational amplifier can be fully compensated. Both
of its output and negative input are directly accessible for external compensation
components.
An example of a suitable compensation network is shown in Figure 15. It consists of a
capacitor CVC1 = 2.2 nF and a resistor RCV1 = 470 kΩ in series.
The current-control transconductance operational amplifier can be fully compensated. Both
its output and negative input are directly accessible for external compensation components.
An example of a suitable compensation network is shown in Figure 15. It consists of a
capacitor CIC1 = 2.2 nF and a resistor RIC1 = 22 kΩ in series. In order to increase the
stability of the application it is suggested to add a resistor in series with the optocoupler. An
example of a suitable RLED value could be 330 Ω in series with the optocoupler.
4.4
Start up and short circuit conditions
Under start-up or short-circuit conditions if the device is supplied from SMPS output and the
output voltage is lower than Vcc minimum the current regulation is not guaranteed.
Therefore, the current limitation can only be ensured by the primary PWM module, which
should be chosen accordingly.
If the primary current limitation is considered not to be precise enough for the application,
then a sufficient supply for the device has to be ensured under any condition. It would then
be necessary to add some circuitry to supply the chip with a separate power line. This can
be achieved in numerous ways, including an additional winding on the transformer.
The following schematic shows how to realize a low-cost power supply for the device (with
no additional windings).
10/15
TSM1052
Application information
Figure 17. Application circuit able to supply the device even with VOUT = 0
Vcc
TSM1052
1.210 V
Rs
+
R1
6
Rled
+
3
OUT
Ds
200 mV
Cvc1
1
+
Vctrl
Vout
Cic1
2
Cs
Rvc1
4
5
Ictrl
Vsense
Rsense
GND
Ric1
R2
Ric2
Iout
11/15
Package mechanical data
5
TSM1052
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
12/15
TSM1052
Package mechanical data
Table 6.
SOT23-6 mechanical data
mm.
inch
Dim.
Min
Typ
Max
A
0.9
A1
Typ
Max
1.45
0.035
0.057
0
0.1
0
0.0039
A2
0.9
1.3
0.035
0.0512
b
0.35
0.5
0.014
0.02
c
0.09
0.2
0.004
0.008
D
2.8
3.05
0.11
0.120
E
1.5
1.75
0.059
0.0689
e
Note:
0.95
Min
0.037
H
2.6
3
0.102
0.118
L
0.1
0.6
0.004
0.024
θ
0
10°
0
10°
Dimensions per JEDEC MO178AB
Figure 18. Package dimensions
13/15
Revision history
6
TSM1052
Revision history
Table 7.
14/15
Document revision history
Date
Revision
Changes
20-Feb-2007
1
Initial release.
07-Feb-2008
2
Updated: Section 5 on page 12
TSM1052
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
15/15