TC7MH175FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MH175FK Quad D-Type Flip-Flop with Clear The TC7MH175FK is an advanced high speed CMOS quad D-type flip-flop fabricated with silicon gate C2MOS technology. It achieves the high speed operation similar to equivalent bipolar schottky TTL while maintaining the CMOS low power dissipation. These four flip-flops are controlled by a clock input (CK) and a clear input (CLR). The information data applied to the D inputs (D1 thru D4) are transferred to the outputs (Q1 thru Q4 and Q1 thru Q4) on the positive-going edge of the clock pulse. When the CLR input is held low , the Q outputs are at the low logic level and the Q outputs are at the high logic level, Weight: 0.02 g (typ.) regardless of other input conditions. An input protection circuit ensures that 0 to 5.5 V can be applied to the input pins without regard to the supply voltage. This device can be used to interface 5 V to 3 V systems and two supply systems such as battery back up. This circuit prevents device destruction due to mismatched supply and input voltages. Features • High speed: fmax = 210 MHz (typ.) (VCC = 5 V) • Low power dissipation: ICC = 4 μA (max) (Ta = 25°C) • High noise immunity: VNIH = VNIL = 28% VCC (min) • Power down protection is provided on all inputs. • Balanced propagation delays: tpLH ≈ tpHL • Wide operating voltage range: VCC (opr) = 2~5.5 V • Low noise: VOLP = 0.8 V (max) • Pin and function compatible with 74ALS175 1 2007-10-19 TC7MH175FK Pin Assignment (top view) IEC Logic Symbol CLR 1 16 VCC Q1 2 15 Q4 Q1 D1 14 3 D2 5 12 D3 Q2 6 11 Q3 Q2 7 10 Q3 GND 8 9 CK D3 D4 C1 (2) (3) (7) (6) (10) (11) (15) (14) 1D (5) D2 D4 R (4) D1 Q4 13 4 (1) CLR (9) CK (12) (13) Q1 Q1 Q2 Q2 Q3 Q3 Q4 Q4 Truth Table Inputs Outputs Function CLR D CK Q Q L X X L H Clear H L L H ⎯ H H H L ⎯ H X Qn Qn No change X: Don’t care System Diagram D2 D1 CLR D4 12 13 1 D R CK CK D3 5 4 R Q D Q CK R Q D Q CK R Q D Q CK Q Q 9 7 6 Q2 Q2 2 3 Q1 Q1 2 10 11 Q3 Q3 15 14 Q4 Q4 2007-10-19 TC7MH175FK Absolute Maximum Ratings (Note) Characteristics Supply voltage range Symbol Rating Unit VCC −0.5~7.0 V VIN −0.5~7.0 V VOUT −0.5~VCC + 0.5 V Input diode current IIK −20 mA Output diode current IOK ±20 mA DC output current IOUT ±25 mA DC VCC/ground current ICC ±50 mA DC input voltage DC output voltage Power dissipation PD 180 mW Storage temperature Tstg −65~150 °C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Operating Ranges (Note) Characteristics Symbol Rating Unit Supply voltage VCC 2.0~5.5 V Input voltage VIN 0~5.5 V VOUT 0~VCC V −40~85 °C Output voltage Operating temperature Topr Input rise and fall time 0~100 (VCC = 3.3 ± 0.3 V) dt/dv 0~20 (VCC = 5 ± 0.5 V) ns/V Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Electrical Characteristics DC Characteristics Characteristics High level Symbol Test Condition VIH ⎯ Ta = 25°C VCC (V) Min Typ. Max Min Max 2.0 1.50 ⎯ ⎯ 1.50 ⎯ 3.0~5.5 VCC × 0.7 ⎯ ⎯ VCC × 0.7 ⎯ 2.0 ⎯ ⎯ 0.50 ⎯ 0.50 3.0~5.5 ⎯ ⎯ VCC × 0.3 ⎯ VCC × 0.3 2.0 1.9 2.0 ⎯ 1.9 ⎯ 3.0 2.9 3.0 ⎯ 2.9 ⎯ 4.5 4.4 4.5 ⎯ 4.4 ⎯ IOH = −4 mA 3.0 2.58 ⎯ ⎯ 2.48 ⎯ IOH = −8 mA 4.5 3.94 ⎯ ⎯ 3.80 ⎯ 2.0 ⎯ 0 0.1 ⎯ 0.1 IOL = 50 μA 3.0 ⎯ 0 0.1 ⎯ 0.1 4.5 ⎯ 0 0.1 ⎯ 0.1 IOL = 4 mA 3.0 ⎯ ⎯ 0.36 ⎯ 0.44 Input voltage Low level High level ⎯ VIL VOH VIN = VIH or VIL Output voltage Low level VOL VIN = VIH or VIL Ta = −40~85°C IOH = −50 μA IOL = 8 mA Unit V V 4.5 ⎯ ⎯ 0.36 ⎯ 0.44 Input leakage current IIN VIN = 5.5 V or GND 0~5.5 ⎯ ⎯ ±0.1 ⎯ ±1.0 μA Quiescent supply current ICC VIN = VCC or GND 5.5 ⎯ ⎯ 4.0 ⎯ 40.0 μA 3 2007-10-19 TC7MH175FK Timing Requirements (Input: tr = tf = 3 ns) Characteristics Symbol Test Condition tw (L) tw (H) ⎯ tw (L) ⎯ Minimum set-up time ts ⎯ Minimum hold time th ⎯ trem ⎯ Minimum pulse width (CK) Minimum pulse width ( CLR ) Minimum removal time ( CLR ) Ta = 25°C Ta = −40~85°C VCC (V) Typ. Limit Limit 3.3 ± 0.3 ⎯ 5.0 5.0 5.0 ± 0.5 ⎯ 5.0 5.0 3.3 ± 0.3 ⎯ 5.0 5.0 5.0 ± 0.5 ⎯ 5.0 5.0 3.3 ± 0.3 ⎯ 5.0 5.0 5.0 ± 0.5 ⎯ 4.0 4.0 3.3 ± 0.3 ⎯ 1.0 1.0 5.0 ± 0.5 ⎯ 1.0 1.0 3.3 ± 0.3 ⎯ 5.0 5.0 5.0 ± 0.5 ⎯ 5.0 5.0 Unit ns ns ns ns ns AC Characteristics (Input: tr = tf = 3 ns) Characteristics Propagation delay time (CK-Q) Propagation delay time ( CLR -Q) Symbol Ta = 25°C Test Condition VCC (V) CL (pF) Typ. Max Min Max 15 ⎯ 7.5 11.5 1.0 13.5 50 ⎯ 10.0 15.0 1.0 17.0 15 ⎯ 4.8 7.3 1.0 8.5 50 ⎯ 6.3 9.3 1.0 10.5 15 ⎯ 6.3 10.1 1.0 12.0 50 ⎯ 8.8 13.6 1.0 15.5 15 ⎯ 4.3 6.4 1.0 7.5 50 ⎯ 5.8 8.4 1.0 9.5 15 90 140 ⎯ 75 ⎯ 50 50 75 ⎯ 45 ⎯ 15 150 210 ⎯ 125 ⎯ 50 85 115 ⎯ 75 ⎯ 3.3 ± 0.3 50 ⎯ ⎯ 1.5 ⎯ 1.5 5.0 ± 0.5 50 ⎯ ⎯ 1.0 ⎯ 1.0 ⎯ 4 10 ⎯ 10 pF ⎯ 44 ⎯ ⎯ ⎯ pF ⎯ 5.0 ± 0.5 3.3 ± 0.3 tpHL ⎯ 5.0 ± 0.5 3.3 ± 0.3 Maximum clock frequency fmax ⎯ 5.0 ± 0.5 Output to output skew tosLH tosHL Input capacitance CIN Power dissipation capacitance CPD (Note 1) Unit Min 3.3 ± 0.3 tpLH tpHL Ta = −40~85°C ⎯ (Note 2) ns ns MHz ns Note 1: Parameter guaranteed by design. tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn| Note 2: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/4 (per bit) And the total CPD when n pcs of flip-flop operate can be gained by the following equation: CPD (total) = 30 + 14･n 4 2007-10-19 TC7MH175FK Noise Characteristics (Input: tr = tf = 3 ns) Characteristics Symbol Test Condition Ta = 25°C VCC (V) Typ. Limit Unit Quiet output maximum dynamic VOL VOLP CL = 50 pF 5.0 0.4 0.8 V Quiet output minimum dynamic VOL VOLV CL = 50 pF 5.0 −0.4 −0.8 V Minimum high level dynamic input voltage VIH VIHD CL = 50 pF 5.0 ⎯ 3.5 V Maximum low level dynamic input voltage VIL VILD CL = 50 pF 5.0 ⎯ 1.5 V Input Equivalent Circuit Input 5 2007-10-19 TC7MH175FK Package Dimensions Weight: 0.02 g (typ.) 6 2007-10-19 TC7MH175FK RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 7 2007-10-19