S6A THRU S6M 6.0 AMPS. Surface Mount Rectifiers Voltage Range 50 to 1000 Volts Current 6.0Amperes SMC / DO-214AB Features For surface mounted application Glass passivated junction chip. Low forward voltage drop High current capability Easy pick and place High surge current capability Plastic material used carries Underwriters Laboratory Classification 94V-O High temperature soldering: 260oC / 10 seconds at terminals .129(3.27) .118(3.0) .245(6.22) .220(5.59) .280(7.11) .260(6.60) .012(.31) .006(.15) .103(2.62) .079(2.00) Mechanical Data Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packaging: 16mm tape per EIA STD RS-481 Weight: 0.21 gram .008(.20) .004(.10) .060(1.52) .030(0.76) .320(8.13) .305(7.75) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol S6A S6B S6D S6G S6J S6K S6M Units Type Number Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 1000 V VRRM Maximum RMS Voltage 35 70 140 280 420 560 700 V VRMS Maximum DC Blocking Voltage 50 100 200 400 600 800 1000 V VDC Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length @TL = 75℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 6.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Typical Junction Capacitance ( Note 1 ) Typical Thermal Resistance ( Note 2 ) Operating Temperature Range I(AV) 6.0 A IFSM 250 A VF 1.15 V 10 400 100 10 -65 to +125 -65 to +150 uA uA pF ℃/W ℃ ℃ IR Cj RθJA TJ TSTG Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 2. Measured on P.C. Board with 0.6 x 0.6” (16 x 16mm) Copper Pad Areas. Storage Temperature Range - 492 - RATINGS AND CHARACTERISTIC CURVES (S6A THRU S6M) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) 7 6 4 2 RESISTIVE OR INDUCTIVE LOAD P. C. BOARD MOUNTED ON 8.0mm2 PAD AREAS 1 0 50 60 70 80 90 100 110 120 130 140 150 165 o LEAD TEMPERATURE. ( C) 100 INSTANTANEOUS REVERSE CURRENT. ( A) FIG.3- TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS FORWARD CURRENT. (A) FIG.2- TYPICAL FORWARD CHARACTERISTICS 100 30 Tj=25 0C PULSE WIDTH-300 S 2% DUTY CYCLE 10 3 1 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 10 Tj=100 0C 1 0.01 2.0 Tj=25 0C 0.1 0 FORWARD VOLTAGE. (V) FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 200 Tj=25 0C 150 100 50 1 5 10 60 80 100 120 140 FIG.5- TYPICAL JUNCTION CAPACITANCE 250 0 40 1000 JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT. (A) 300 20 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 50 100 500 200 Tj=25 0C 100 50 10 1 10 REVERSE VOLTAGE. (V) NUMBER OF CYCLES AT 60Hz - 493 - 50 100