COILCRAFT ST413RAB182XJLZ

1008 CHIP INDUCTORS
Chip Inductors for Critical Applications ST413RAB
•Lower DCR than other 1008 inductors
•Ferrite construction for high current handling
•Inductance values: 1.0 – 100 µH
Part number1
Inductance2
(µH)
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
ST413RAB104XJLZ
[email protected]
SRF min4
DCR max5
Percent
Imax
Q min3
(MHz)(Ohms) (mA)
tolerance
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
1. When ordering, please specify termination and testing codes:
ST413RAB104JLZ
Termination:L=RoHS compliant silver-palladium-platinum-glass frit.
Special order:
T = Tin-silver-copper (95.5/4/0.5) over silver-palladiumplatinum-glass frit or
S=Tin-lead (63/37) over silver-palladium-platinumglass frit.
Testing:Z=COTS
H=Screening per Coilcraft CP-SA-10001
2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/
HP 4286A impedance analyzer or equivalent with Coilcraft-provided
correlation pieces.
3. Q measured using an Agilent/HP 4291A with an Agilent/HP 16197 test
fixture or equivalents.
4. SRF measured using an Agilent/HP 8753ES network analyzer or
equivalent with a Coilcraft SMD-D fixture.
5. DCR measured on a Keithley 580 micro-ohmmeter or equivalent and a
Coilcraft CCF858 test fixture.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
230
210
190
170
150
135
120
105
85
90
30
80
75
70
65
57
60
38
30
26
22
12
19
26
12
8.0
5.7
4.5
370
370
370
370
310
270
260
250
230
230
200
220
195
210
190
170
165
160
150
140
115
110
110
90
80
95
85
65
Core material Ceramic/Ferrite
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 38.3 – 41.0 mg
Ambient temperature –40°C to +85°C with Imax current, +85°C to
+100°C with derated current
Storage temperature Component: –55°C to +100°C.
Tape and reel packaging: –55°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +25 to +125 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Enhanced crush-resistant packaging 2000/7″ reel; 7500/13″ reel.
Plastic tape: 8 mm wide, 0.3 mm thick, 4 mm pocket spacing,
2.0 mm pocket depth
Document ST103-1 Revised 12/05/12
®
© Coilcraft, Inc. 2012
0.62
0.68
0.76
0.84
1.10
1.28
1.46
1.56
1.70
1.68
2.20
1.82
2.50
2.00
2.65
2.90
2.95
3.30
3.70
4.00
6.14
6.45
7.00
10.0
10.7
10.0
13.5
20.5
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
Fax 847-639-1508
Email [email protected]
www.coilcraft-cps.com
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specifications subject to change without notice.
Please check our web site for latest information.
1008 CHIP INDUCTORS
ST413RAB Series (1008)
Typical Q vs Frequency
Typical L vs Frequency
1000
50
40
68 µH
30
Inductance (µH)
Q Factor
1.8 µH
6.8 µH
10 µH
33 µH
20
68 µH
100
33 µH
10 µH
6.8 µH
10
1.8 µH
10
0
1
1
10
1
100
1000
Frequency (MHz)
Current Derating
C
B
overall
120
100
A
H
D
Pick and
place
material
F
110
I
G
J
F
I
90
80
E
terminal
70
60
50
30
20
10
0
-40
-20
0
20
Terminal wraparound:
approx 0.010/0,25 both ends
Suggested
Recommended
Land
Land Pattern
Pattern
A
B
C D
max max max ref
E
F
G
H
IJ
0.1150.1100.0800.0200.0800.0200.0600.100 0.0400.050inches
2,922,792,030,512,030,511,522,54 1,021,27
mm
40
25°C
Percent of rated Irms
100
10
Frequency (MHz)
40
60
80
100
120
Note: Dimensions are before optional solder application. For maximum
overall dimensions including solder, add 0.0025 in / 0,064 mm to B
and 0.006 in / 0,15 mm to A and C.
Ambient temperature (°C)
Document ST103-2 Revised 12/05/12
®
© Coilcraft, Inc. 2012
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
Fax 847-639-1508
Email [email protected]
www.coilcraft-cps.com
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specifications subject to change without notice.
Please check our web site for latest information.