The SN54F299 is obsolete and no
longer supplied.
SDFS071B − MARCH 1987 − REVISED APRIL 2004
D Four Modes of Operation:
D
D
D
D
D
SN54F299 . . . J PACKAGE
SN74F299 . . . DW, N, OR NS PACKAGE
(TOP VIEW)
− Hold (Store)
− Shift Right
− Shift Left
− Load Data
Operates With Outputs Enabled or at High
Impedance
3-State Outputs Drive Bus Lines Directly
Can Be Cascaded for N-Bit Word Lengths
Direct Overriding Clear
Applications:
− Stacked or Pushdown Registers
− Buffer Storage
− Accumulator Registers
S0
OE1
OE2
G/QG
E/QE
C/QC
A/QA
QA′
CLR
GND
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
VCC
S1
SL
QH′
H/QH
F/QF
D/QD
B/QB
CLK
SR
SN54F299 . . . FK PACKAGE
(TOP VIEW)
OE2
OE1
S0
VCC
S1
description/ordering information
These 8-bit universal shift /storage registers
feature multiplexed I/O ports to achieve full 8-bit
data handling in a single 20-pin package. Two
function-select (S0, S1) inputs and two
output-enable (OE1, OE2) inputs can be used to
choose the modes of operation listed in the
function table.
G/QG
E/QE
C/QC
A/QA
QA′
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
SL
QH′
H/QH
F/QF
D/QD
CLR
GND
SR
CLK
B/QB
9 10 11 12 13
Synchronous parallel loading is accomplished by
taking both S0 and S1 high. This places the
3-state outputs in a high-impedance state and
permits data that is applied on the I/O ports to
be clocked into the register. Reading out of the register can be accomplished while the outputs are enabled in
any mode. Clearing occurs when the clear (CLR) input is low. Taking either OE1 or OE2 high disables the outputs
but has no effect on clearing, shifting, or storage of data.
ORDERING INFORMATION
PDIP − N
0°C to 70°C
ORDERABLE
PART NUMBER
PACKAGE†
TA
SOIC − DW
Tube of 20
SN74F299N
Tube of 25
SN74F299DW
Reel of 2000
SN74F299DWR
TOP-SIDE
MARKING
SN74F299N
F299
SOP − NS
Reel of 2000
SN74F299NSR
74F299
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2004, Texas Instruments Incorporated
!"#$%&'#! ( )*$$+!' &( #" ,*-.)&'#! /&'+0
$#/*)'( )#!"#$% '# (,+)")&'#!( ,+$ '1+ '+$%( #" +2&( !('$*%+!'(
('&!/&$/ 3&$$&!'40 $#/*)'#! ,$#)+((!5 /#+( !#' !+)+((&$.4 !).*/+
'+('!5 #" &.. ,&$&%+'+$(0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
The SN54F299 is obsolete and no
longer supplied.
SDFS071B − MARCH 1987 − REVISED APRIL 2004
FUNCTION TABLE
INPUTS
MODE
OE2†
I/O PORTS
OUTPUTS
CLR
S1
S0
OE1†
CLK
SL
SR
A/QA
B/QB
C/QC
D/QD
QA′
QH′
Clear
L
X
H
L
L
X
L
L
X
X
X
X
X
X
X
X
X
X
L
L
X
L
L
X
L
L
X
L
L
X
F/QF
L
L
X
H/QH
X
L
H
E/QE
L
L
X
G/QG
L
L
L
L
L
X
L
L
X
L
L
L
L
L
L
Hold
H
H
L
X
L
X
L
L
L
L
X
L
X
X
X
X
QA0
QA0
QB0
QB0
QC0
QC0
QD0
QD0
QE0
QE0
QF0
QF0
QG0
QG0
QH0
QH0
QA0
QA0
QH0
QH0
Shift
Right
H
H
L
L
H
H
L
L
L
L
↑
↑
X
X
H
L
H
L
QAn
QAn
QBn
QBn
QCn
QCn
QDn
QDn
QEn
QEn
QFn
QFn
QGn
QGn
H
L
QGn
QGn
Shift
Left
H
H
H
H
L
L
L
L
L
L
↑
↑
H
L
X
X
QBn
QBn
QCn
QCn
QDn
QDn
QEn
QEn
QFn
QFn
QGn
QGn
QHn
QHn
H
L
QBn
QBn
H
L
Load
H
H
H
X
X
↑
X
X
a
b
c
d
e
f
g
h
a
h
NOTE: a . . . h = the level of the steady-state input at inputs A through H, respectively. This data is loaded into the flip-flops while the flip-flop
outputs are isolated from the I/O terminals.
† When one or both output-enable inputs are high, the eight I/O terminals are disabled to the high-impedance state; however, sequential operation
or clearing of the register is not affected.
logic diagram (positive logic)
S0
S1
SR
(shift right
serial input)
CLK
1
19
18
11
Six
Identical
Channels
Not
Shown‡
12
1D
1D
C1
C1
R
QA′
CLR
OE1
OE2
R
8
17
9
2
3
7
16
A /QA
H /QH
‡ I/O ports not shown: B/QB (13), C/QC (6), D/QD (14), E/QE (5), F/QF (15), and G/QG (4).
2
SL
(shift left
serial input)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
QH′
The SN54F299 is obsolete and no
longer supplied.
SDFS071B − MARCH 1987 − REVISED APRIL 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −1.2 V to 7 V
Input current range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −30 mA to 5 mA
Voltage range applied to any output in the disabled or power-off state . . . . . . . . . . . . . . . . . . . . −0.5 V to 5.5 V
Voltage range applied to any output in the high state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC
Current into any output in the low state: QA′ or QH′ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
SN54F299 (QA thru QH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
SN74F299 (QA thru QH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 mA
Package thermal impedance, θJA (see Note 2): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input voltage ratings may be exceeded provided the input current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 3)
SN54F299
SN74F299
MIN
NOM
MAX
MIN
NOM
MAX
4.5
5
5.5
4.5
5
5.5
UNIT
VCC
VIH
Supply voltage
VIL
IIK
Low-level input voltage
0.8
0.8
V
Input clamp current
−18
−18
mA
−1
High-level output current
QA′ or QH′
−1
IOH
QA thru QH
−3
−3
20
Low-level output current
QA′ or QH′
20
IOL
QA thru QH
20
24
High-level input voltage
2
2
V
V
mA
mA
TA
Operating free-air temperature
−55
125
0
70
°C
NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
The SN54F299 is obsolete and no
longer supplied.
SDFS071B − MARCH 1987 − REVISED APRIL 2004
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VIK
VCC = 4.5 V,
QA thru QH
Any output
VCC = 4.75 V,
QA thru QH
IIH‡
IIL‡
3.4
2.5
3.4
2.5
3.4
2.5
3.4
2.4
3.3
2.4
3.3
VCC = 5.5 V
VI = 5.5 V
VI = 7 V
VCC = 5.5 V,
VI = 2.7 V
0.3
0.5
0.3
0.5
0.3
0.5
0.35
0.5
V
1
1
0.1
70
70
20
20
A thru H
−0.65
−0.65
S0 or S1
−1.2
−1.2
−0.6
−0.6
A thru H
Any other
VCC = 5.5 V,
V
V
0.1
Any other
UNIT
2.7
IOL = 20 mA
IOL = 24 mA
A thru H
II
−1.2
2.5
IOH = − 1 mA to − 3 mA
IOL = 20 mA
VCC = 4.5 V
SN74F299
TYP†
MAX
MIN
−1.2
IOH = − 1 mA
IOH = − 3 mA
VCC = 4.5 V
QA′ or QH′
VOL
MIN
II = − 18 mA
IOH = − 1 mA
QA′ or QH′
VOH
SN54F299
TYP†
MAX
TEST CONDITIONS
VI = 0.5 V
Any other
IOS§
VCC = 5.5 V,
VO = 0
−60
−150
−60
ICC
VCC = 5.5 V,
See Note 4
68
95
68
† All typical values are at VCC = 5 V, TA = 25°C.
‡ For I/O ports (QA thru QH), the parameters IIH and IIL include the off-state output current.
§ Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
NOTE 4: ICC is measured with OE1, OE2, and CLK at 4.5 V.
mA
µA
A
mA
−150
mA
95
mA
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
VCC = 5 V,
TA = 25°C
SN54F299
SN74F299
MIN
MIN
′F299
MIN
fclock
tw
tsu
th
Clock frequency
Pulse duration
Setup time before
CLK↑
Inactive-state setup
time before CLK↑¶
Hold time after CLK↑
70
MAX
65
7
8
7
CLR low
7
8
7
S0 or S1
High or low
8.5
9.5
8.5
A/QA thru H/QH, SR, or SL
High or low
5.5
6.5
5.5
CLR
High
7
13
7
S0 or S1
High or low
0
0
0
A /QA thru H /QH, SR, or SL
High or low
2
2
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MAX
70
CLK high or low
¶ Inactive-state setup time also is referred to as recovery time.
4
MAX
UNIT
MHz
ns
ns
ns
The SN54F299 is obsolete and no
longer supplied.
SDFS071B − MARCH 1987 − REVISED APRIL 2004
switching characteristics (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
VCC = 5 V,
CL = 50 pF,
RL = 500 Ω,
TA = 25°C
VCC = 4.5 V to 5.5 V,
CL = 50 pF,
RL = 500 Ω,
TA = MIN to MAX†
′F299
fmax
tPLH
tPHL
tPLH
tPHL
CLK
QA
A′ or QH
H′
CLK
QA thru QH
MAX
UNIT
SN54F299
SN74F299
MIN
MIN
MIN
TYP
70
100
MAX
3.2
6.6
9
2.7
10.5
3.2
10
2.7
6.1
8.5
2.2
10
2.7
9.5
3.2
6.6
9
2.7
11
3.2
10
4.2
8.1
11
3.7
12.5
4.2
12
65
MAX
70
MHz
QA′ or QH′
3.7
7.1
9.5
3.2
11.5
3.7
10.5
QA thru QH
5.7
10.6
14
5
15.5
5.7
15
2.7
5.6
8
2.2
10.5
2.7
9
3.2
6.6
10
2.7
12
3.2
11
1.7
4.1
6
1.7
9
1.7
7
1.2
3.6
5.5
1.2
7.5
1.2
6.5
tPHL
CLR
tPZH
tPZL
OE1 or OE2
QA thru QH
tPHZ
tPLZ
OE1 or OE2
QA thru QH
ns
ns
ns
ns
ns
† For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
The SN54F299 is obsolete and no
longer supplied.
SDFS071B − MARCH 1987 − REVISED APRIL 2004
PARAMETER MEASUREMENT INFORMATION
7V
From Output
Under Test
CL
(see Note A)
500 Ω S1
From Output
Under Test
Test
Point
CL
(see Note A)
500 Ω
Open
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7V
Open
7V
Open Collector
LOAD CIRCUIT FOR
3-STATE AND OPEN-DRAIN OUTPUTS
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
3V
Timing Input
1.5 V
0V
tw
tsu
3V
1.5 V
Input
1.5 V
th
3V
1.5 V
1.5 V
Data Input
0V
1.5 V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
1.5 V
Input
1.5 V
0V
tPLH
tPHL
1.5 V
1.5 V
VOL
tPHL
1.5 V
VOH
1.5 V
VOL
Output
Waveform 2
S1 at GND
(see Note B)
1.5 V
0V
Output
Waveform 1
S1 at 7 V
(see Note B)
tPLH
1.5 V
3V
Output
Control
tPZL
VOH
In-Phase
Output
Out-of-Phase
Output
0V
VOLTAGE WAVEFORMS
PULSE DURATION
tPLZ
1.5 V
tPZH
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
≈3.5 V
VOL + 0.3 V
VOL
tPHZ
1.5 V
VOH − 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns,
duty cycle = 50%.
D. The outputs are measured one at a time, with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN74F299DW
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74F299DWG4
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74F299DWR
ACTIVE
SOIC
DW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74F299DWRE4
ACTIVE
SOIC
DW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74F299DWRG4
ACTIVE
SOIC
DW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74F299N
ACTIVE
PDIP
N
20
CU NIPDAU
N / A for Pkg Type
Lead/Ball Finish
MSL Peak Temp (3)
20
Pb-Free
(RoHS)
TBD
Call TI
20
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
SN74F299N3
OBSOLETE
PDIP
N
20
SN74F299NE4
ACTIVE
PDIP
N
20
Call TI
SN74F299NSR
ACTIVE
SO
NS
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74F299NSRE4
ACTIVE
SO
NS
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74F299NSRG4
ACTIVE
SO
NS
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
SN74F299DWR
Package Package Pins
Type Drawing
SOIC
DW
20
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
2000
330.0
24.4
Pack Materials-Page 1
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
10.8
13.0
2.7
12.0
24.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN74F299DWR
SOIC
DW
20
2000
346.0
346.0
41.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated