ALUMINUM ELECTROLYTIC CAPACITORS WX 5.5mmL Chip Type series Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Load life of 2000 hours at 85°C. WT High Temperature WX WP Bi-polarized Smaller Specifications ZS Item Performance Characteristics Category Temperature Range – 40 ~ +85°C Rated Voltage Range 4 ~ 50V Rated Capacitance Range 0.1 ~ 330µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ Rated voltage (V) tan δ (MAX.) 4 6.3 10 16 25 35 50 0.35 (0.40) 0.26 (0.30) 0.20 (0.24) 0.16 (0.19) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) 6.3 4 8 4 7 15 Rated voltage (V) Z– 25°C / Z+20°C Z– 40°C / Z+20°C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristic requirements listed at right. Endurance 10 3 8 Capacitance change tan δ Within ±20% of initial value (Within ±25% for 4 V and φ3,WR series units) 200% or less of initial specified value Leakage Current Initial specifed value or less Shelf Life After leaving capacitors under no load at 85°C for 1000 hours, they meet the specified value for endurance characteristics listed above. Resistance to soldering heat The capacitors shall be kept on the hot plate maintained at 250°C for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. Marking Black print on the case top. Chip Type Leakage current Within ±10% of initial value Initial specified value or less Initial specified value or less Type numbering system (Example : 16V 10µF) 5.4 1 +0.1 –0.2 0.5 ~ 0.8 2 3 4 5 6 7 8 9 10 11 12 13 14 UWX 1 C 1 0 0 MC R 1 G B A±0.2 A±0.2 B±0.2 C±0.2 0.5 MAX. Plastic platform 0.3 MAX. E 1 Voltage φD±0.5 X2 10 16V Capacitance change tan δ Positive Capacitance 2 Lot No. Values in ( ) applicable to WR, φ3 case size. Measurement frequency : 120Hz 16 25 35 50 2 2 2 2 4 4 3 3 φD A B C E 3 1.5 3.3 3.3 0.8 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 8 2.4 3.3 6.6 8.3 6.6 8.3 2.2 2.3 Taping code Size code Configuration Capacitance toleranc (±20%) Rated Capacitance (10µF) Negative 1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated voltage is omitted. 2. In case of marking for φ3 units, Lot No.is expressed by a digit (month code). φD Code 3 2 4~8 1 Rated voltage (16V) Series name Type • The lead-free product is also available upon request. In this case, L will be put at 11th digit of type numbering system. • In the case of size φ3 in ( ),parentheses, use WX in the 2nd and 3rd digit and put a 2 in the 12th digit of type numbering system. Dimension table in next page. CAT.8100T ALUMINUM ELECTROLYTIC CAPACITORS WX series Dimensions 4 0G V Cap. (µF) Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 0.1 0R1 4 (3) 1.0 0.22 R22 4 (3) 2.0 0.33 R33 4 (3) 2.8 0.47 R47 4 (3) 4.0 1 010 4 (3) 2.2 2R2 3.3 3R3 4.7 4R7 3 3 10 4 17 4 (3) 16 (12) 4 18 5 20 (18) 5 27 (24) 5 29 (24) 6.3 33 (30) 33 (30) 5 37 (30) 6.3 42 (38) 6.3 46 (39) 8 52 (43) 5 41 (34) 6.3 49 (44) 6.3 52 (46) 8 62 (53) 8 71 45 (40) 6.3 52 (47) 6.3 58 (52) 8 70 (60) 8 80 22 220 3 019 4 (3) 28 (21) 5 33 330 4 028 5 37 (34) 47 470 4 033 5 56 560 5 042 6.3 52 (46) 6.3 57 (50) 6.3 63 (57) 8 100 101 5 056 6.3 70 (47) 6.3 76 (54) 6.3 86 8 150 151 6.3 079 6.3 220 221 6.3 096 8 110 (74) 330 331 8 145 8 170 71 8 111 (76) 8 135 76 (65) 110 ( ) is also available with φ3mm upon request. ),parentheses, use WX at 2nd and 3rd digit and put 2 at the 12th digit of type numbering system. } 13 (10) 23 (18) 100 Size φ4 is available for capacitors marked. " " Size φ5 is available for capacitors marked. " " Size φ6.3 is available for capacitors marked. " " 8.4 (8.0) 4 (3) 4 (3) 10 • In the case of size φ3 in ( 8.4 Case size Rated φ D (mm) ripple Rated Ripple (mA rms) at 85°C 120Hz ( ) = φ3 units and WR Series In such a case, W R will be put at 2nd and 3rd digit of type numbering system. Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 22. Recommended land size are given in page 23 Please refer to page 3 for the minimum order quantity. CAT.8100T