I N D U C T O R S May 2013 Inductors for Standard Circuits Multilayer Ferrite MLFseries MLF1005 MLF1608 MLF2012 1005 [0402 inch]* 1608 [0603 inch] 2012 [0805 inch] * Dimensions Code JIS[EIA] (1/22) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130516 / e511_mlf.fm (2/22) I N D U C T O R S Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Inductors for Standard Circuits Multilayer Ferrite Overview of the MLF Series FEATURES The lineup includes a wide inductance range. Highly reliable monolithic structure with multilayer integration. APPLICATION Smart phones, tablet terminals, tuners, LCD-TVs, PDP-TVs, audio equipment, computers, signal processing for modules, etc. PART NUMBER CONSTRUCTION MLF Series name 1005 L×W×H Dimensions (mm) 1005 1.0×0.5×0.5 1608 1.6×0.8×0.8 2.0×1.25×0.85 2012 2.0×1.25×1.25 L characteristics A C D E G K L V R10 K Inductance (µH) 0.010 10N (10nH) R10 0.1 1R0 1 100 10 Inductance tolerance K ±10% M ±20% T □□□ Packaging style Internal code T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type Temperature range Operating Storage temperature temperature （°C） （°C） –55 to +125 –55 to +125 –40 to +85 –40 to +85 –40 to +85 –40 to +85 Package quantity Individual weight (pieces/reel) 10,000 10,000 4,000 4,000 2,000 （mg） 1.2 1.2 4 10 14 MLF1005V.1005G MLF1005L MLF1608 t=0.85 MLF2012 –40 to +85 –40 to +85 t=1.25 The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (3/22) I N D U C T O R S Overview of the MLF Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. Time T4 t3 250 to 260°C 10s max. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (4/22) I N D U C T O R S MLF series MLF1005 Type 0.50±0.05 SHAPE & DIMENSIONS 0.10min. 0.10min. 0.50±0.05 1.00±0.05 Dimensions in mm 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (5/22) I N D U C T O R S MLF series MLF1005 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (µH) Tolerance 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% L, Q measuring conditions Frequency Current (MHz) (mA) 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 Self-resonant frequency (MHz) min. 450 400 350 320 290 260 230 210 190 170 210 190 170 150 130 120 110 100 90 80 450 400 350 320 290 260 230 210 190 170 150 130 120 110 100 90 80 Q min. 10 10 15 15 15 15 15 15 15 15 30 30 30 30 30 30 30 30 30 30 10 10 10 10 10 10 10 25 25 25 25 25 25 25 25 25 25 DC resistance (Ω ) max. Rated current (mA) max. Part No. 0.51 0.59 0.63 0.72 0.79 0.91 1.05 1.35 1.50 1.95 0.41 0.42 0.47 0.55 0.59 0.64 0.79 0.95 1.05 1.30 0.51 0.59 0.63 0.76 0.79 0.91 1.05 0.41 0.42 0.47 0.55 0.59 0.64 0.79 0.95 1.05 1.15 180 180 180 160 160 150 140 130 120 120 50 50 45 45 40 40 35 35 30 30 150 140 130 120 110 100 90 50 50 45 40 35 35 35 30 20 15 MLF1005VR10KT MLF1005VR12KT MLF1005VR15KT MLF1005VR18KT MLF1005VR22KT MLF1005VR27KT MLF1005VR33KT MLF1005VR39KT MLF1005VR47KT MLF1005VR56KT MLF1005GR39KT MLF1005GR47KT MLF1005GR56KT MLF1005GR68KT MLF1005GR82KT MLF1005G1R0KT MLF1005G1R2KT MLF1005G1R5KT MLF1005G1R8KT MLF1005G2R2KT MLF1005LR10KT MLF1005LR12KT MLF1005LR15KT MLF1005LR18KT MLF1005LR22KT MLF1005LR27KT MLF1005LR33KT MLF1005LR39KT MLF1005LR47KT MLF1005LR56KT MLF1005LR68KT MLF1005LR82KT MLF1005L1R0KT MLF1005L1R2KT MLF1005L1R5KT MLF1005L1R8KT MLF1005L2R2KT The " □□□ " of the Part Number contains the internal code. ○ Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (6/22) I N D U C T O R S MLF series MLF1005 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10 G1R8 G1R2 Inductance(µH) 1 GR39 GR82 GR56 VR33 VR22 0.1 VR15 VR10 VR47 0.01 1 10 100 1000 Frequency(MHz) 10 G2R2 G1R5 Inductance(µH) GR47 G1R0 1 GR68 VR39 VR27 VR18 VR12 0.1 VR56 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (7/22) I N D U C T O R S MLF series MLF1005 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 3 L2R2 Inductance(µH) 2 L1R5 L1R0 1 LR33 LR68 LR47 LR22 LR15 LR10 0 1 10 100 1000 Frequency(MHz) 3 Inductance(µH) 2 L1R8 L1R2 1 LR82 LR56 LR27 LR39 LR18 LR12 0 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (8/22) I N D U C T O R S MLF series MLF1005 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 60 GR39 G1R2 VR10 50 VR22 GR56 G1R8 GR82 VR47 40 Q VR33 VR15 30 20 10 0 1 10 100 1000 Frequency(MHz) 70 G1R0 60 VR27 50 VR56 GR68 GR47 VR12 Q 40 VR18 G1R5 30 VR39 G2R2 20 10 0 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (9/22) I N D U C T O R S MLF series MLF1005 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 80 70 L2R2 L1R5 L1R0 LR47 60 LR68 50 Q LR22 40 LR15 LR10 30 LR33 20 10 0 1 10 100 1000 Frequency(MHz) 70 L1R2 L1R8 60 LR56 LR82 50 LR39 LR12 40 Q LR27 LR18 30 20 10 0 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (10/22) I N D U C T O MLF series MLF1608 R S Type 0.80±0.15 SHAPE & DIMENSIONS 0.30±0.20 0.30±0.20 0.80±0.15 1.60±0.15 Dimensions in mm 0.8 RECOMMENDED LAND PATTERN 0.6 0.8 0.6 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (11/22) I N D U C T O R S MLF series MLF1608 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q (µH) Tolerance min. typ. 0.047 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 ±20% ±20% ±20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% 10 10 10 15 15 15 15 15 15 15 15 15 15 15 15 35 35 35 35 35 35 35 35 35 35 35 35 30 30 20 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 30 30 30 30 50 50 55 55 55 55 60 60 60 60 60 60 55 55 40 40 40 40 40 L, Q measuring conditions Frequency Current (MHz) (mA) 50 1.0 50 1.0 50 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 25 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 10 1.0 4 0.1 4 0.1 4 0.1 2 0.1 2 0.1 1 0.1 1 0.1 1 0.1 1 0.1 1 0.1 Self-resonant frequency(MHz) DC resistance (Ω ) Rated current (mA) min. typ. max. typ. max. 600 550 500 450 400 350 320 290 260 230 210 190 170 150 130 120 110 100 90 80 70 65 60 55 45 40 35 30 25 22 20 18 15 10 900 700 650 600 550 500 450 400 350 320 290 260 230 210 190 170 150 140 130 120 110 100 90 80 70 60 55 50 45 42 40 38 35 30 0.20 0.30 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.75 0.85 0.95 1.05 1.25 1.40 0.50 0.65 0.70 0.85 1.00 1.15 1.30 1.45 1.60 1.10 1.30 1.50 1.70 1.80 1.50 1.60 1.70 1.80 2.20 0.10 0.15 0.15 0.20 0.20 0.25 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.65 0.75 0.25 0.25 0.30 0.35 0.45 0.50 0.55 0.65 0.75 0.55 0.65 0.80 1.00 1.20 0.80 0.85 0.90 1.20 1.40 200 200 200 200 200 200 150 150 150 100 100 100 100 70 70 50 50 50 50 30 30 30 30 30 15 15 10 10 10 2 2 2 2 2 Part No. MLF1608D47NMT MLF1608D68NMT MLF1608D82NMT MLF1608DR10KT MLF1608DR12KT MLF1608DR15KT MLF1608DR18KT MLF1608DR22KT MLF1608DR27KT MLF1608DR33KT MLF1608DR39KT MLF1608DR47KT MLF1608DR56KT MLF1608DR68KT MLF1608DR82KT MLF1608A1R0KT MLF1608A1R2KT MLF1608A1R5KT MLF1608A1R8KT MLF1608A2R2KT MLF1608A2R7KT MLF1608A3R3KT MLF1608A3R9KT MLF1608A4R7KT MLF1608E5R6KT MLF1608E6R8KT MLF1608E8R2KT MLF1608E100KT MLF1608E120KT MLF1608C150KT MLF1608C180KT MLF1608C220KT MLF1608C270KT MLF1608C330KT The " □□□ " of the Part Number contains the internal code. ○ Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (12/22) I N D U C T O R S MLF series MLF1608 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 E6R8 10 E100 Inductance(µH) A4R7 A3R3 A1R0 1 A2R2 A1R5 DR68 DR47 DR33 DR22 DR15 0.1 DR10 0.01 1 10 100 1000 Frequency(MHz) 100 E120 10 E5R6 E8R2 Inductance(µH) A3R9 A2R7 A1R2 1 A1R8 DR82 DR56 DR39 DR27 DR18 0.1 DR12 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (13/22) I N D U C T O R S MLF series MLF1608 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 C330 C270 Inductance(µH) 10 C220 C180 C150 1 0.1 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (14/22) I N D U C T O R S MLF series MLF1608 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 A3R3 60 A1R0 A1R5 A2R2 50 DR47 40 DR15 Q DR22 DR33 E6R8 E100 30 DR10 20 DR68 10 0 1 10 100 1000 Frequency(MHz) 70 60 A3R9 A1R2 E8R2 50 E5R6 Q 40 E120 30 A1R8 A2R7 DR12 DR82 DR56 DR18 20 DR39 10 0 DR27 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (15/22) I N D U C T O R S MLF series MLF1608 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 60 50 C150 C330 40 Q C270 30 C180 C220 20 10 0 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (16/22) I N D U C T O MLF series MLF2012 R S Type 1.25±0.20 SHAPE & DIMENSIONS 0.50±0.30 0.50±0.30 T 2.00±0.20 T 0.85±0.20 1.25±0.20 Dimensions in mm 1.2 RECOMMENDED LAND PATTERN 0.8 1.0 0.8 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (17/22) I N D U C T O R S MLF series MLF2012 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L L, Q measuring conditions Q (µH) Tolerance min. typ. 0.047 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 ±20% ±20% ±20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% 15 15 15 20 20 20 20 20 20 20 25 25 25 25 25 45 45 45 45 45 45 45 45 45 50 50 50 50 50 30 30 30 30 30 35 35 35 25 25 25 25 25 25 30 30 30 30 30 30 30 35 35 35 35 35 55 55 60 60 60 70 70 70 70 75 75 75 75 75 45 45 45 45 45 55 55 55 45 45 45 Frequency (MHz) 50 50 50 25 25 25 25 25 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 4 4 4 2 2 1 1 1 1 0.4 2 2 2 1 1 1 Current (mA) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 Self-resonant DC resistance frequency(MHz) (Ω ) Rated current (mA) min. typ. max. typ. max. 550 500 450 400 360 320 280 250 220 200 180 160 150 140 130 120 110 100 90 80 70 60 55 50 45 40 35 30 25 22 20 18 17 15 13 11 10 9 8 7 700 600 550 500 450 410 370 330 300 270 250 230 210 190 170 160 150 140 130 120 100 90 80 70 65 60 55 50 45 40 38 35 33 28 23 20 18 16 14 12 0.10 0.15 0.15 0.15 0.20 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.60 0.65 0.70 0.80 0.90 0.70 0.80 0.90 1.00 1.10 2.40 2.70 2.80 2.90 3.00 3.10 0.05 0.08 0.08 0.10 0.12 0.13 0.15 0.16 0.18 0.23 0.25 0.25 0.30 0.35 0.40 0.15 0.15 0.18 0.20 0.22 0.25 0.28 0.30 0.35 0.30 0.32 0.35 0.40 0.50 0.35 0.38 0.45 0.50 0.55 1.30 1.60 1.80 2.00 2.40 2.50 300 300 300 300 300 300 300 250 250 250 200 200 150 150 150 80 80 80 80 50 50 50 30 30 15 15 15 15 15 5 5 5 5 5 4 4 4 2 2 2 Thickness T Part No. (mm) 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 1.25 1.25 1.25 1.25 0.85 0.85 0.85 0.85 0.85 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 MLF2012D47NMT MLF2012D68NMT MLF2012D82NMT MLF2012DR10KT MLF2012DR12KT MLF2012DR15KT MLF2012DR18KT MLF2012DR22KT MLF2012DR27KT MLF2012DR33KT MLF2012DR39KT MLF2012DR47KT MLF2012DR56KT MLF2012DR68KT MLF2012DR82KT MLF2012A1R0KT MLF2012A1R2KT MLF2012A1R5KT MLF2012A1R8KT MLF2012A2R2KT MLF2012A2R7KT MLF2012A3R3KT MLF2012A3R9KT MLF2012A4R7KT MLF2012E5R6KT MLF2012E6R8KT MLF2012E8R2KT MLF2012E100KT MLF2012E120KT MLF2012C150KT MLF2012C180KT MLF2012C220KT MLF2012C270KT MLF2012C330KT MLF2012K390KT MLF2012K470KT MLF2012K560KT MLF2012C680KT MLF2012C820KT MLF2012C101KT The " □□□ " of the Part Number contains the internal code. ○ Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (18/22) I N D U C T O R S MLF series MLF2012 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 E100 10 A4R7 Inductance(µH) E6R8 A1R0 1 A3R3 A2R2 A1R5 DR68 DR47 DR33 DR22 DR15 0.1 DR10 0.01 1 10 100 1000 Frequency(MHz) 100 E120 10 E8R2 A3R9 Inductance(µH) E5R6 DR82 A2R7 A1R8 DR56 A1R2 1 DR39 DR27 DR18 0.1 DR12 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (19/22) I N D U C T O R S MLF series MLF2012 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 C680 C101 C820 K470 10 Inductance(µH) K560 K390 C270 C220 C330 C150 1 C180 0.1 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (20/22) I N D U C T O R S MLF series MLF2012 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 90 A4R7 80 A3R3 70 A2R2 A1R5 E100 60 DR22 DR15 E6R8 DR33 Q 50 A1R0 40 DR47 DR10 30 DR68 20 10 0 1 10 100 1000 Frequency(MHz) 90 80 E5R6 E8R2 A3R9 A2R7 70 E120 60 Q DR18 DR39 A1R8 50 A1R2 DR12 40 DR82 30 DR56 20 DR27 10 0 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (21/22) I N D U C T O R S MLF series MLF2012 Type Q FREQUENCY CHARACTERISTICS GRAPH 90 80 70 K470 60 C330 50 C270 Q C180 K390 40 K560 C101 C220 30 C680 C820 20 C150 10 0 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm (22/22) I N D U C T O R S MLF series Packaging Style REEL DIMENSIONS ø60min. 1.0 2.0±0.5 8.4 +2.0 –0.0 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm 3.5±0.05 Cavity Type MLF1005 MLF1608 t=0.85 MLF2012 t=1.25 A 0.8 max. 1.1 max. 1.1 max. 1.5 max. B 0.65±0.1 1.1±0.2 1.5±0.2 1.5±0.2 C 1.15±0.1 1.9±0.2 2.3±0.2 2.3±0.2 C 8.0±0.3 Sprocket hole 1.5 +0.1 –0.0 1.75±0.1 TAPE DIMENSIONS A B 4.0±0.1 2.0±0.05 160min. Taping 2.0±0.05 200min. 300min. Drawing direction Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e511_mlf.fm