TM ispMACH 4000V/B/C Family 3.3V/2.5V/1.8V In-System Programmable SuperFAST TM High Density PLDs June 2002 Data Sheet ■ Broad Device Offering Features • • • • ■ High Performance • fMAX = 400MHz maximum operating frequency • tPD = 2.5ns propagation delay • Up to four global clock pins with programmable clock polarity control • Up to 80 PTs per output 32 to 512 macrocells 30 to 208 I/O pins 44 to 256 pins/balls in TQFP or fpBGA packages Commercial and industrial temperature ranges ■ Easy System Integration • Operation with 3.3V, 2.5V or 1.8V LVCMOS I/O • Operation with 3.3V (4000V), 2.5V (4000B) or 1.8V (4000C) supplies • Hot-socketing • Open-drain capability • Input pull-up, pull-down or bus-keeper • Programmable output slew rate • 3.3V PCI compatible • IEEE 1149.1 boundary scan testable • 3.3V/2.5V/1.8V In-System Programmable (ISP™) using IEEE 1532 compliant interface • I/O pins with fast setup path ■ Ease of Design • Enhanced macrocells with individual clock, reset, preset and clock enable controls • Up to four global OE controls • Individual local OE control per I/O pin • Excellent First-Time-FitTM and refit • Fast path, SpeedLockingTM Path, and wide-PT path • Wide input gating (36 input logic blocks) for fast counters, state machines and address decoders ■ Low Power • 1.8V core E2CMOS® technology • CMOS design techniques provide low static and dynamic power Table 1. ispMACH 4000V/B/C Family Selection Guide ispMACH 4032V/B/C Macrocells ispMACH 4064V/B/C ispMACH 4128V/B/C ispMACH 4256V/B/C ispMACH 4384V/B/C ispMACH 4512V/B/C 32 64 128 256 384 512 30/32 30/32/64 64/92 64/128/160 128/192 128/208 tPD (ns) 2.5 2.5 2.7 3.0 3.5 3.5 tS (ns) 1.8 1.8 1.8 2.0 2.0 2.0 User I/O Options tCO (ns) 2.2 2.2 2.7 2.7 2.7 2.7 fMAX (MHz) 400 400 333 322 322 322 3.3/2.5/1.8V 3.3/2.5/1.8V 3.3/2.5/1.8V 3.3/2.5/1.8V 3.3/2.5/1.8V 3.3/2.5/1.8V 44 TQFP 48 TQFP 44 TQFP 48 TQFP 100 TQFP 100 TQFP 128 TQFP 100 TQFP 176 TQFP 256 fpBGA 176 TQFP 256 fpBGA Supply Voltages (V) Pins/Package 176 TQFP 256 fpBGA* *128-I/O and 160-I/O configurations. www.latticesemi.com 1 ispm4k_08 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000 Introduction The high performance ispMACH 4000 family from Lattice offers a SuperFAST CPLD solution. The family is a blend of Lattice’s two most popular architectures: the ispLSI® 2000 and ispMACH 4A. Retaining the best of both families, the ispMACH 4000 architecture focuses on significant innovations to combine the highest performance with low power in a flexible CPLD family. The ispMACH 4000 combines high speed and low power with the flexibility needed for ease of design. With its robust Global Routing Pool and Output Routing Pool, this family delivers excellent First-Time-Fit, timing predictability, routing, pin-out retention and density migration. The ispMACH 4000 family offers densities ranging from 32 to 512 macrocells. There are multiple density-I/O combinations in Thin Quad Flat Pack (TQFP) and Fine Pitch BGA (fpBGA) packages ranging from 44 to 256 pins/balls. Table 1 shows the macrocell, package and I/O options, along with other key parameters. The ispMACH 4000 family has enhanced system integration capabilities. It supports 3.3V (4000V), 2.5V (4000B) and 1.8V (4000C) supply voltages and 3.3V, 2.5V and 1.8V interface voltages. The ispMACH 4000 also offers enhanced I/O features such as slew rate control, PCI compatibility, bus-keeper latches, pull-up resistors, pull-down resistors, open drain outputs and hot socketing. The ispMACH 4000 family members are 3.3V/2.5V/1.8V in-system programmable through the IEEE Standard 1532 interface. IEEE Standard 1149.1 boundary scan testing capability also allows product testing on automated test equipment. Overview The ispMACH 4000 devices consist of multiple 36-input, 16-macrocell Generic Logic Blocks (GLBs) interconnected by a Global Routing Pool (GRP). Output Routing Pools (ORPs) connect the GLBs to the I/O Blocks (IOBs), which contain multiple I/O cells. This architecture is shown in Figure 1. 16 16 Generic Logic Block 36 I/O Block ORP 16 36 16 16 36 36 2 Generic 16 Logic Block VCCO1 GND TCK TMS TDI TDO VCC GND GOE0 GOE1 16 I/O Bank 0 ORP Generic Logic Block I/O Block ORP I/O Bank 1 I/O Block Global Routing Pool VCCO0 GND CLK0/I CLK1/I CLK2/I CLK3/I Figure 1. Functional Block Diagram Generic 16 Logic Block I/O Block ORP Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet The I/Os in the ispMACH 4000 are split into two banks. Each bank has a separate I/O power supply. Inputs can support a variety of standards independent of the chip or bank power supply. Outputs support the standards compatible with the power supply provided to the bank. Support for a variety of standards helps designers implement designs in mixed voltage environments. ispMACH 4000 Architecture There are a total of two GLBs in the ispMACH 4032, increasing to 32 GLBs in the ispMACH 4512. Each GLB has 36 inputs. All GLB inputs come from the GRP and all outputs from the GLB are brought back into the GRP to be connected to the inputs of any other GLB on the device. Even if feedback signals return to the same GLB, they still must go through the GRP. This mechanism ensures that GLBs communicate with each other with consistent and predictable delays. The outputs from the GLB are also sent to the ORP. The ORP then sends them to the associated I/O cells in the I/O block. Generic Logic Block The ispMACH 4000 GLB consists of a programmable AND array, logic allocator, 16 macrocells and a GLB clock generator. Macrocells are decoupled from the product terms through the logic allocator and the I/O pins are decoupled from macrocells through the ORP. Figure 2 illustrates the GLB. To GRP CLK3 CLK2 CLK1 CLK0 Figure 2. Generic Logic Block Clock Generator 1+OE 1+OE 1+OE 1+OE To ORP 16 MC Feedback Signals 16 Macrocells Logic Allocator 36 Inputs from GRP AND Array 36 Inputs, 83 Product Terms 1+OE 1+OE 1+OE 1+OE To Product Term Output Enable Sharing AND Array The programmable AND Array consists of 36 inputs and 83 output product terms. The 36 inputs from the GRP are used to form 72 lines in the AND Array (true and complement of the inputs). Each line in the array can be connected to any of the 83 output product terms via a wired-AND. Each of the 80 logic product terms feed the logic allocator with the remaining three control product terms feeding the Shared PT Clock, Shared PT Initialization and Shared PT OE. The Shared PT Clock and Shared PT Initialization signals can optionally be inverted before being fed to the macrocells. Every set of five product terms from the 80 logic product terms forms a product term cluster starting with PT0. There is one product term cluster for every macrocell in the GLB. Figure 3 is a graphical representation of the AND Array. 3 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Figure 3. AND Array In[0] In[34] In[35] PT0 PT1 PT2 PT3 PT4 Cluster 0 PT75 PT76 PT77 Cluster 15 PT78 PT79 PT80 Shared PT Clock PT81 Shared PT Initialization PT82 Shared PTOE Note: Indicates programmable fuse. Enhanced Logic Allocator Within the logic allocator, product terms are allocated to macrocells in product term clusters. Each product term cluster is associated with a macrocell. The cluster size for the ispMACH 4000 family is 4+1 (total 5) product terms. The software automatically considers the availability and distribution of product term clusters as it fits the functions within a GLB. The logic allocator is designed to provide three speed paths: 5-PT fast bypass path, 20-PT Speed Locking path and an up to 80-PT path. The availability of these three paths lets designers trade timing variability for increased performance. The enhanced Logic Allocator of the ispMACH 4000 family consists of the following blocks: • Product Term Allocator • Cluster Allocator • Wide Steering Logic Figure 4 shows a macrocell slice of the Logic Allocator. There are 16 such slices in the GLB. Figure 4. Macrocell Slice to to n-1 n-2 from from n-1 n-4 From n-4 Fast 5-PT Path 1-80 PTs 5-PT n To XOR (MC) Cluster to n+1 Individual Product Term Allocator from n+2 Cluster Allocator 4 from n+1 To n+4 SuperWIDE™ Steering Logic Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Product Term Allocator The product term allocator assigns product terms from a cluster to either logic or control applications as required by the design being implemented. Product terms that are used as logic are steered into a 5-input OR gate associated with the cluster. Product terms that used for control are steered either to the macrocell or I/O cell associated with the cluster. Table 2 shows the available functions for each of the five product terms in the cluster. The OR gate output connects to the associated I/O cell, providing a fast path for narrow combinatorial functions, and to the logic allocator. Table 2. Individual PT Steering Product Term Logic PTn Logic PT Control Single PT for XOR/OR PTn+1 Logic PT Individual Clock (PT Clock) PTn+2 Logic PT Individual Initialization or Individual Clock Enable (PT Initialization/CE) PTn+3 Logic PT Individual Initialization (PT Initialization) PTn+4 Logic PT Individual OE (PTOE) Cluster Allocator The cluster allocator allows clusters to be steered to neighboring macrocells, thus allowing the creation of functions with more product terms. Table 3 shows which clusters can be steered to which macrocells. Used in this manner, the cluster allocator can be used to form functions of up to 20 product terms. Additionally, the cluster allocator accepts inputs from the wide steering logic. Using these inputs, functions up to 80 product terms can be created. Table 3. Available Clusters for Each Macrocell Macrocell Available Clusters M0 — C0 C1 C2 M1 C0 C1 C2 C3 M2 C1 C2 C3 C4 M3 C2 C3 C4 C5 M4 C3 C4 C5 C6 M5 C4 C5 C6 C7 M6 C5 C6 C7 C8 M7 C6 C7 C8 C9 M8 C7 C8 C9 C10 M9 C8 C9 C10 C11 M10 C9 C10 C11 C12 M11 C10 C11 C12 C13 M12 C11 C12 C13 C14 M13 C12 C13 C14 C15 M14 C13 C14 C15 — M15 C14 C15 — — Wide Steering Logic The wide steering logic allows the output of the cluster allocator n to be connected to the input of the cluster allocator n+4. Thus, cluster chains can be formed with up to 80 product terms, supporting wide product term functions and allowing performance to be increased through a single GLB implementation. Table 4 shows the product term chains. 5 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Table 4. Product Term Expansion Capability Expansion Chains Macrocells Associated with Expansion Chain (with Wrap Around) Max PT/ Macrocell Chain-0 M0 → M4 → M8 → M12 → M0 75 Chain-1 M1 → M5 → M9 → M13 → M1 80 Chain-2 M2 → M6 → M10 → M14 → M2 75 Chain-3 M3 → M7 → M11 → M15 → M3 70 Every time the super cluster allocator is used, there is an incremental delay of tEXP . When the super cluster allocator is used, all destinations other than the one being steered to, are given the value of ground (i.e., if the super cluster is steered to M (n+4), then M (n) is ground). Macrocell The 16 macrocells in the GLB are driven by the 16 outputs from the logic allocator. Each macrocell contains a programmable XOR gate, a programmable register/latch, along with routing for the logic and control functions. Figure 5 shows a graphical representation of the macrocell. The macrocells feed the ORP and GRP. A direct input from the I/O cell allows designers to use the macrocell to construct high-speed input registers. A programmable delay in this path allows designers to choose between the fastest possible set-up time and zero hold time. Figure 5. Macrocell Power-up Initialization Shared PT Initialization PT Initialization (optional) PT Initialization/CE (optional) Delay From I/O Cell R From Logic Allocator D/T/L P To ORP Q To GRP CE Single PT Block CLK0 Block CLK1 Block CLK2 Block CLK3 PT Clock (optional) Shared PT Clock Enhanced Clock Multiplexer The clock input to the flip-flop can select any of the four block clocks along with the shared PT clock, and true and complement forms of the optional individual term clock. An 8:1 multiplexer structure is used to select the clock. The eight sources for the clock multiplexer are as follows: • Block CLK0 • Block CLK1 6 Lattice Semiconductor • • • • • • ispMACH 4000V/B/C Family Data Sheet Block CLK2 Block CLK3 PT Clock PT Clock Inverted Shared PT Clock Ground Clock Enable Multiplexer Each macrocell has a 4:1 clock enable multiplexer. This allows the clock enable signal to be selected from the following four sources: • PT Initialization/CE • PT Initialization/CE Inverted • Shared PT Clock • Logic High Initialization Control The ispMACH 4000 family architecture accommodates both block-level and macrocell-level set and reset capability. There is one block-level initialization term that is distributed to all macrocell registers in a GLB. At the macrocell level, two product terms can be “stolen” from the cluster associated with a macrocell to be used for set/reset functionality. A reset/preset swapping feature in each macrocell allows for reset and preset to be exchanged, providing flexibility. Note that the reset/preset swapping selection feature affects power-up reset as well. All flip-flops power up to a known state for predictable system initialization. If a macrocell is configured to SET on a signal from the block-level initialization, then that macrocell will be SET during device power-up. If a macrocell is configured to RESET on a signal from the block-level initialization or is not configured for set/reset, then that macrocell will RESET on powerup. To guarantee initialization values, the VCC rise must be monotonic, and the clock must be inactive until the reset delay time has elapsed. GLB Clock Generator Each ispMACH 4000 device has four clock pins that are also routed to the GRP to be used as inputs. These pins drive a clock generator in each GLB, as shown in Figure 6. The clock generator provides four clock signals that can be used anywhere in the GLB. These four GLB clock signals can consist of a number of combinations of the true and complement edges of the global clock signals. Figure 6. GLB Clock Generator CLK0 Block CLK0 CLK1 Block CLK1 CLK2 Block CLK2 CLK3 Block CLK3 7 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Output Routing Pool (ORP) The Output Routing Pool allows macrocell outputs to be connected to any of several I/O cells within an I/O block. This provides greater flexibility in determining the pinout and allows design changes to occur without affecting the pinout. The output routing pool also provides a parallel capability for routing macrocell-level OE product terms. This allows the OE product term to follow the macrocell output as it is switched between I/O cells. Additionally, the output routing pool allows the macrocell output or true and complement forms of the 5-PT bypass signal to bypass the output routing multipliers and feed the I/O cell directly. The enhanced ORP of the ispMACH 4000 family consists of the following elements: • Output Routing Multiplexers • OE Routing Multiplexers • Output Routing Pool Bypass Multiplexers Figure 7 shows the structure of the ORP from the I/O cell perspective. This is referred to as an ORP slice. Each ORP has as many ORP slices as there are I/O cells in the corresponding I/O block. Figure 7. ORP Slice OE Routing Multiplexer From PTOE To I/O Cell OE ORP Bypass Multiplexer 5-PT Fast Path To I/O Cell From Macrocell Output Output Routing Multiplexer Output Routing Multiplexers The details of connections between the macrocells and the I/O cells vary across devices and within a device dependent on the maximum number of I/Os available. Tables 5, 6, 7 and 8 provide the connection details. Table 5. ORP Combinations for I/O Blocks with 8 I/Os I/O Cell Available Macrocells I/O 0 M0, M1, M2, M3, M4, M5, M6, M7 I/O 1 M2, M3, M4, M5, M6, M7, M8, M9 I/O 2 M4, M5, M6, M7, M8, M9, M10, M11 I/O 3 M6, M7, M8, M9, M10, M11, M12, M13 I/O 4 M8, M9, M10, M11, M12, M13, M14, M15 I/O 5 M10, M11, M12, M13, M14, M15, M0, M1 I/O 6 M12, M13, M14, M15, M0, M1, M2, M3 I/O 7 M14, M15, M0, M1, M2, M3, M4, M5 8 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Table 6. ORP Combinations for I/O Blocks with 16 I/Os I/O Cell Available Macrocells I/O 0 M0, M1, M2, M3, M4, M5, M6, M7 I/O 1 M1, M2, M3, M4, M5, M6, M7, M8 I/O 2 M2, M3, M4, M5, M6, M7, M8, M9 I/O 3 M3, M4, M5, M6, M7, M8, M9, M10 I/O 4 M4, M5, M6, M7, M8, M9, M10, M11 I/O 5 M5, M6, M7, M8, M9, M10, M11, M12 I/O 6 M6, M7, M8, M9, M10, M11, M12, M12 I/O 7 M7, M8, M9, M10, M11, M12, M13, M14 I/O 8 M8, M9, M10, M11, M12, M13, M14, M15 I/O 9 M9, M10, M11, M12, M13, M14, M15, M0 I/O 10 M10, M11, M12, M13, M14, M15, M0, M1 I/O 11 M11, M12, M13, M14, M15, M0, M1, M2 I/O 12 M12, M13, M14, M15, M0, M1, M2, M3 I/O 13 M13, M14, M15, M0, M1, M2, M3, M4 I/O 14 M14, M15, M0, M1, M2, M3, M4, M5 I/O 15 M15, M0, M1, M2, M3, M4, M5, M6 Table 7. ORP Combinations for I/O Blocks with 4 I/Os I/O Cell Available Macrocells I/O 0 M0, M1, M2, M3, M4, M5, M6, M7 I/O 1 M4, M5, M6, M7, M8, M9, M10, M11 I/O 2 M8, M9, M10, M11, M12, M13, M14, M15 I/O 3 M12, M13, M14, M15, M0, M1, M2, M3 Table 8. ORP Combinations for I/O Blocks with 10 I/Os I/O Cell Available Macrocells I/O 0 M0, M1, M2, M3, M4, M5, M6, M7 I/O 1 M2, M3, M4, M5, M6, M7, M8, M9 I/O 2 M4, M5, M6, M7, M8, M9, M10, M11 I/O 3 M6, M7, M8, M9, M10, M11, M12, M13 I/O 4 M8, M9, M10, M11, M12, M13, M14, M15 I/O 5 M10, M11, M12, M13, M14, M15, M0, M1 I/O 6 M12, M13, M14, M15, M0, M1, M2, M3 I/O 7 M14, M15, M0, M1, M2, M3, M4, M5 I/O 8 M2, M3, M4, M5, M6, M7, M8 I/O 9 M10, M11, M12, M13, M14, M15, M0, M1 9 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ORP Bypass and Fast Output Multiplexers The ORP bypass and fast-path output multiplexer is a 4:1 multiplexer and allows the 5-PT fast path to bypass the ORP and be connected directly to the pin with either the regular output or the inverted output. This multiplexer also allows the register output to bypass the ORP to achieve faster tCO. Output Enable Routing Multiplexers The OE Routing Pool provides the corresponding local output enable (OE) product term to the I/O cell. I/O Cell The I/O cell contains the following programmable elements: output buffer, input buffer, OE multiplexer and bus maintenance circuitry. Figure 8 details the I/O cell. Figure 8. I/O Cell GOE 0 GOE 1 GOE 2 GOE 3 From ORP VCC VCCO VCCO * From ORP * * To Macrocell To GRP *Global fuses Each output supports a variety of output standards dependent on the VCCO supplied to its I/O bank. Outputs can also be configured for open drain operation. Each input can be programmed to support a variety of standards, independent of the VCCO supplied to its I/O bank. The I/O standards supported are: • LVTTL • LVCMOS 1.8 • LVCMOS 3.3 • 3.3V PCI Compatible • LVCMOS 2.5 All of the I/Os and dedicated inputs have the capability to provide a bus-keeper latch, Pull-up Resistor or Pull-down Resistor. A fourth option is to provide none of these. The selection is done on a global basis. The default in both hardware and software is such that when the device is erased or if the user does not specify, the input structure is configured to be a Pull-up Resistor. Each ispMACH 4000 device I/O has an individually programmable output slew rate control bit. Each output can be individually configured for the higher speed transition (~3V/ns) or for the lower noise transition (~1V/ns). For highspeed designs with long, unterminated traces, the slow-slew rate will introduce fewer reflections, less noise and keep ground bounce to a minimum. For designs with short traces or well terminated lines, the fast slew rate can be used to achieve the highest speed. The slew rate is adjusted independent of power. Global OE Generation Most ispMACH 4000 family devices have a 4-bit wide Global OE Bus, except the ispMACH 4032 device that has a 2-bit wide Global OE Bus. This bus is derived from a 4-bit internal global OE PT bus and two dual purpose I/O or GOE pins. Each signal that drives the bus can optionally be inverted. 10 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Each GLB has a block-level OE PT that connects to all bits of the Global OE PT bus with four fuses. Hence, for a 256-macrocell device (with 16 blocks), each line of the bus is driven from 16 OE product terms. Figures 9 and 10 show a graphical representation of the global OE generation. Figure 9. Global OE Generation for All Devices Except ispMACH 4032 Internal Global OE PT Bus (4 lines) Global OE 4-Bit Global OE Bus Shared PTOE (Block 0) Shared PTOE (Block n) Global Fuses GOE (0:3) to I/O cells Fuse connection Hard wired Figure 10. Global OE Generation for ispMACH 4032 Internal Global OE PT Bus (2 lines) Global OE 4-Bit Global OE Bus Shared PTOE (Block 0) Shared PTOE (Block 1) Global Fuses Fuse connection Hard wired 11 GOE (3:0) to I/O cells Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Low Power and Power Management The ispMACH 4000 family is designed with high speed low power design techniques to offer both high speed and low power. With an advanced E2 low power cell and non sense-amplifier design approach (full CMOS logic approach), the ispMACH 4000 family offers SuperFAST pin-to-pin speeds, while simultaneously delivering low standby power without needing any “turbo bits” or other power management schemes associated with a traditional sense-amplifier approach. IEEE 1149.1-Compliant Boundary Scan Testability All ispMACH 4000 devices have boundary scan cells and are compliant to the IEEE 1149.1 standard. This allows functional testing of the circuit board on which the device is mounted through a serial scan path that can access all critical logic notes. Internal registers are linked internally, allowing test data to be shifted in and loaded directly onto test nodes, or test node data to be captured and shifted out for verification. In addition, these devices can be linked into a board-level serial scan path for more board-level testing. The test access port operates with an LVCMOS interface that corresponds to the power supply voltage. I/O Quick Configuration To facilitate the most efficient board test, the physical nature of the I/O cells must be set before running any continuity tests. As these tests are fast, by nature, the overhead and time that is required for configuration of the I/Os’ physical nature should be minimal so that board test time is minimized. The ispMACH 4000 family of devices allows this by offering the user the ability to quickly configure the physical nature of the I/O cells. This quick configuration takes milliseconds to complete, whereas it takes seconds for the entire device to be programmed. Lattice's ispVM™ System programming software can either perform the quick configuration through the PC parallel port, or can generate the ATE or test vectors necessary for a third-party test system. IEEE 1532-Compliant In-System Programming Programming devices in-system provides a number of significant benefits including: rapid prototyping, lower inventory levels, higher quality and the ability to make in-field modifications. All ispMACH 4000 devices provide In-System Programming (ISP™) capability through the Boundary Scan Test Access Port. This capability has been implemented in a manner that ensures that the port remains complaint to the IEEE 1149.1 standard. By using IEEE 1149.1 as the communication interface through which ISP is achieved, users get the benefit of a standard, welldefined interface. All ispMACH 4000 devices are also compliant with the IEEE 1532 standard. The ispMACH 4000 devices can be programmed across the commercial temperature and voltage range. The PCbased Lattice software facilitates in-system programming of ispMACH 4000 devices. The software takes the JEDEC file output produced by the design implementation software, along with information about the scan chain, and creates a set of vectors used to drive the scan chain. The software can use these vectors to drive a scan chain via the parallel port of a PC. Alternatively, the software can output files in formats understood by common automated test equipment. This equipment can then be used to program ispMACH 4000 devices during the testing of a circuit board. Security Bit A programmable security bit is provided on the ispMACH 4000 devices as a deterrent to unauthorized copying of the array configuration patterns. Once programmed, this bit defeats readback of the programmed pattern by a device programmer, securing proprietary designs from competitors. Programming and verification are also defeated by the security bit. The bit can only be reset by erasing the entire device. Hot Socketing The ispMACH 4000 devices are well-suited for applications that require hot socketing capability. Hot socketing a device requires that the device, during power-up and down, can tolerate active signals on the I/Os and inputs without being damaged. Additionally, it requires that the effects of I/O pin loading be minimal on active signals. 12 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Density Migration The ispMACH 4000 family has been designed to ensure that different density devices in the same package have the same pin-out. Furthermore, the architecture ensures a high success rate when performing design migration from lower density parts to higher density parts. In many cases, it is possible to shift a lower utilization design targeted for a high density device to a lower density device. However, the exact details of the final resource utilization will impact the likely success in each case. 13 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Absolute Maximum Ratings1, 2, 3 ispMACH 4000C ispMACH 4000B ispMACH 4000V (1.8V) (2.5V) (3.3V) Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . -0.5 to 2.5V . . . . . . . . . .-0.5 to 5.5V. . . . . . . . . . -0.5 to 5.5V Output Supply Voltage (VCCO) . . . . . . . . . . . . . . . -0.5 to 4.5V . . . . . . . . . .-0.5 to 4.5V. . . . . . . . . . -0.5 to 4.5V Input or I/O Tristate Voltage Applied4 . . . . . . . . . . -0.5 to 4.5V . . . . . . . . . .-0.5 to 4.5V. . . . . . . . . . -0.5 to 4.5V Storage Temperature . . . . . . . . . . . . . . . . . . . . . . -65 to 150°C. . . . . . . . . -65 to 150°C . . . . . . . . .-65 to 150°C Junction Temperature (Tj) with Power Applied . . . -55 to 150°C. . . . . . . . . -55 to 150°C . . . . . . . . .-55 to 150°C 1. Stress above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. 2. Compliance with Lattice Thermal Management document is required. 3. All voltages referenced to GND. 4. Overshoot and undershoot of -2V to (VIH (MAX) +2) volts is permitted for a duration of < 20ns. Recommended Operating Conditions Symbol Parameter VCC Min Max Supply Voltage for 1.8V Devices 1.65 1.95 V Supply Voltage for 2.5V Devices 2.3 2.7 V Supply Voltage for 3.3V Devices 3.0 3.6 V 0 90 C -40 105 C Min Max Units 1,000 — Cycles Junction Temperature (Commercial) Tj Junction Temperature (Industrial) Units Erase Reprogram Specifications Parameter Erase/Reprogram Cycle Note: Valid over commercial temperature range. Hot Socketing Characteristics1,2,3 Symbol IDK 1. 2. 3. Parameter Input or I/O Leakage Current Condition Min Typ Max Units 0 ≤ VIN ≤ VIH (MAX) — — ±150 µA Insensitive to sequence of VCC and VCCO. However, assumes monotonic rise/fall rates for VCC and VCCO. 0 < VCC < VCC (MAX), 0 < VCCO < VCCO (MAX). IDK is additive to IPU , IPD or IBH. Device defaults to pull-up until fuse circuitry is active. I/O Recommended Operating Conditions VCCO (V)1 Standard Min Max LVTTL 3.0 3.6 LVCMOS 3.3 3.0 3.6 LVCMOS 2.5 2.3 2.7 LVCMOS 1.8 1.65 1.95 PCI 3.3 3.0 3.6 1. Typical values for VCCO are the average of the Min and Max values. 14 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet DC Electrical Characteristics Over Recommended Operating Conditions Min Typ Max Units IIL, IIH1 Symbol Input Leakage Current Parameter 0 ≤ VIN ≤ VIH (MAX) Condition — — 10 µA 0 ≤ VIN ≤ 0.7VCCO 30 — 150 µA 30 — 150 µA IPU I/O Weak Pull-up Resistor Current IPD I/O Weak Pull-down Resistor Current VIL (MAX) ≤ VIN ≤ VIH (MIN) IBHLS Bus Hold Low Sustaining Current VIN = VIL (MAX) 30 — — µA IBHHS Bus Hold High Sustaining Current VIN = 0.7 VCCO -30 — — µA IBHLO Bus Hold Low Overdrive Current 0V ≤ VIN ≤ VBHT — — 150 µA IBHHO Bus Hold High Overdrive Current VBHT ≤ VIN ≤ VCCO — — -150 µA VBHT Bus Hold Trip Points VCCO * 0.35 — VCCO * 0.65 V C1 I/O Capacitance2 C2 Clock Capacitance2 C3 Global Input Capacitance2 — VCCO = 3.3V, 2.5V, 1.8V — VCC = 1.8V, VIO = 0 to VIH (MAX) — VCCO = 3.3V, 2.5V, 1.8V — VCC = 1.8V, VIO = 0 to VIH (MAX) — VCCO = 3.3V, 2.5V, 1.8V — VCC = 1.8V, VIO = 0 to VIH (MAX) — 8 6 6 — — — — — — 1. Input or I/O leakage current is measured with the pin configured as an input or as an I/O with the output driver tristated. It is not measured with the output driver active. Bus maintenance circuits are disabled. 2. TA = 25°C, f = 1.0MHz 15 pf pf pf Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Supply Current Over Recommended Operating Conditions Symbol Parameter Condition Min Typ Max Units VCC = 3.3V — 11.8 — mA VCC = 2.5V — 11.8 — mA VCC = 1.8V — 1.8 — mA VCC = 3.3V — 11.3 — mA VCC = 2.5V — 11.3 — mA VCC = 1.8V — 1.3 — mA VCC = 3.3V — 12 — mA VCC = 2.5V — 12 — mA ispMACH 4032V/B/C 1, 2, 3 ICC ICC4 Operating Power Supply Current Standby Power Supply Current ispMACH 4064V/B/C ICC1, 2, 3 4 ICC Operating Power Supply Current Standby Power Supply Current VCC = 1.8V — 2 — mA VCC = 3.3V — 11.5 — mA VCC = 2.5V — 11.5 — mA VCC = 1.8V — 1.5 — mA VCC = 3.3V — 12 — mA VCC = 2.5V — 12 — mA VCC = 1.8V — 2 — mA VCC = 3.3V — 11.5 — mA VCC = 2.5V — 11.5 — mA VCC = 1.8V — 1.5 — mA VCC = 3.3V — 12.5 — mA VCC = 2.5V — 12.5 — mA ispMACH 4128V/B/C 1, 2, 3 ICC ICC4 Operating Power Supply Current Standby Power Supply Current ispMACH 4256V/B/C ICC1, 2, 3 ICC4 Operating Power Supply Current Standby Power Supply Current VCC = 1.8V — 2.5 — mA VCC = 3.3V — 12 — mA VCC = 2.5V — 12 — mA VCC = 1.8V — 2 — mA VCC = 3.3V — 13.5 — mA VCC = 2.5V — 13.5 — mA VCC = 1.8V — 3.5 — mA VCC = 3.3V — 12.5 — mA VCC = 2.5V — 12.5 — mA VCC = 1.8V — 2.5 — mA VCC = 3.3V — 14 — mA VCC = 2.5V — 14 — mA ispMACH 4384V/B/C 1, 2, 3 ICC ICC4 Operating Power Supply Current Standby Power Supply Current ispMACH 4512V/B/C ICC1, 2, 3 4 ICC Operating Power Supply Current Standby Power Supply Current VCC = 1.8V — 4 — mA VCC = 3.3V — 13 — mA VCC = 2.5V — 13 — mA VCC = 1.8V — 3 — mA 1. TA = 25°C, frequency = 1.0MHz. 2. Device configured with 16-bit counters. 3. ICC varies with specific device configuration and operating frequency. 4. TA = 25°C 16 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet I/O DC Electrical Characteristics Over Recommended Operating Conditions VIH VIL Standard Min (V) Max (V) Min (V) Max (V) -0.3 0.80 2.0 3.6 LVTTL LVCMOS 3.3 -0.3 LVCMOS 2.5 0.80 -0.3 2.0 0.70 3.6 1.70 3.6 VOL Max (V) VOH Min (V) IOL1 (mA) IOH1 (mA) 0.40 VCCO - 0.40 8.0 -4.0 0.20 VCCO - 0.20 0.1 -0.1 0.40 VCCO - 0.40 8.0 -4.0 0.20 VCCO - 0.20 0.1 -0.1 0.40 VCCO - 0.40 8.0 -4.0 0.20 VCCO - 0.20 0.1 -0.1 0.40 VCCO - 0.45 2.0 -2.0 LVCMOS 1.8 -0.3 0.35 VCC 0.65 * VCC 3.6 0.20 VCCO - 0.20 0.1 -0.1 PCI 3.3 (4000V/B) -0.3 1.08 1.5 3.6 0.1 VCCO 0.9 VCCO 1.5 -0.5 PCI 3.3 (4000C) -0.3 3.6 0.1 VCCO 0.9 VCCO 1.5 -0.5 0.3 * 3.3 * (VCC / 1.8) 0.5 * 3.3 * (VCC / 1.8) 1. The average DC current drawn by I/Os between adjacent bank GND connections, or between the last GND in an I/O bank and the end of the I/O bank, as shown in the logic signals connection table, shall not exceed n*8mA. Where n is the number of I/Os between bank GND connections or between the last GND in a bank and the end of a bank. 3.3V VCCO IOL IOH 80 60 40 20 0 0.5 1.0 1.5 50 IOL IOH 40 30 20 10 0 2.0 2.5 3.0 3.5 50 IOL IOH 40 30 20 10 0 0.5 1.0 1.5 0.5 1.0 1.5 2.0 VO Output Voltage (V) 1.8V VCCO 60 Typical I/O Output Current (mA) 60 0 0 VO Output Voltage (V) 0 2.5V VCCO 70 Typical I/O Output Current (mA) Typical I/O Output Current (mA) 100 2.0 VO Output Voltage (V) 17 2.5 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C External Switching Characteristics Over Recommended Operating Conditions -25 Parameter 1, 2, 3 Description -27 -3 -35 Min. Max. Min. Max. Min. Max. Min. Max. Units tPD 5-PT bypass combinatorial propagation delay — 2.5 — 2.7 — 3.0 — 3.5 ns tPD_MC 20-PT combinatorial propagation delay through macrocell — 3.2 — 3.5 — 3.8 — 4.2 ns tS GLB register setup time before clock 1.8 — 1.8 — 2.0 — 2.0 — ns tST GLB register setup time before clock with T-type register 2.0 — 2.0 — 2.2 — 2.2 — ns tSIR GLB register setup time before clock, input register path 0.7 — 1.0 — 1.0 — 1.0 — tSIRZ GLB register setup time before clock with zero hold 1.7 — 2.0 — 2.0 — 2.0 — tH GLB register hold time after clock 0.0 — 0.0 — 0.0 — 0.0 — ns tHT GLB register hold time after clock with T-type register 0.0 — 0.0 — 0.0 — 0.0 — ns tHIR GLB register hold time after clock, input register path 0.9 — 1.0 — 1.0 — 1.0 — tHIRZ GLB register hold time after clock, input register path with zero hold 0.0 — 0.0 — 0.0 — 0.0 — tCO GLB register clock-to-output delay — 2.2 — 2.7 — 2.7 — 2.7 tR External reset pin to output delay — 3.5 — 4.0 — 4.4 — 4.5 ns tRW External reset pulse duration 1.5 — 1.5 — 1.5 — 1.5 - ns tPTOE/DIS Input to output local product term output enable/disable — 4.0 — 4.5 — 5.0 — 5.5 tGPTOE/DIS Input to output global product term output enable/disable — 5.0 — 6.5 — 8.0 — 8.0 ns ns ns ns ns ns ns tGOE/DIS Global OE input to output enable/disable — 3.0 — 3.5 — 4.0 — 4.5 ns tCW Global clock width, high or low 1.1 — 1.3 — 1.3 — 1.3 — ns tGW Global gate width low (for low transparent) or high (for high transparent) 1.1 — 1.3 — 1.3 — 1.3 — ns tWIR Input register clock width, high or low 1.1 — 1.3 — 1.3 — 1.3 — ns fMAX4 Clock frequency with internal feedback 400 — 333 — 322 — 322 — MHz fMAX (Ext.) Clock frequency with external feedback, [1/ (tS + tCO)] 250 — 222 — 212 — 212 — MHz Timing v.3.1 1. 2. 3. 4. Timing numbers are based on default LVCMOS 1.8 I/O buffers. Use timing adjusters provided to calculate other standards. Measured using standard switching circuit, assuming GRP loading of 1 and 1 output switching. Pulse widths and clock widths less than minimum will cause unknown behavior. Standard 16-bit counter using GRP feedback. 18 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C External Switching Characteristics (Cont.) Over Recommended Operating Conditions -5 Parameter Description1, 2, 3 -105 -75 Min. Max. Min. Max. Min. Max. Units tPD 5-PT bypass combinatorial propagation delay — 5.0 — 7.5 — 10.0 ns tPD_MC 20-PT combinatorial propagation delay through macrocell — 5.5 — 8.0 — 10.5 ns tS GLB register setup time before clock 3.0 — 4.5 — 5.5 — ns tST GLB register setup time before clock with T-type register 3.2 — 4.7 — 5.5 — ns tSIR GLB register setup time before clock, input register path 1.2 — 1.7 — 1.7 — ns tSIRZ GLB register setup time before clock with zero hold 2.2 — 2.7 — 2.7 — ns tH GLB register hold time after clock 0.0 — 0.0 — 0.0 — ns tHT GLB register hold time after clock with T-type register 0.0 — 0.0 — 0.0 — ns tHIR GLB register hold time after clock, input register path 1.0 — 1.0 — 1.0 — ns tHIRZ GLB register hold time after clock, input register path with zero hold 0.0 — 0.0 — 0.0 — tCO GLB register clock-to-output delay — 3.40 — 4.5 — 6.0 tR External reset pin to output delay — 6.30 — 9.0 — 10.5 ns tRW External reset pulse duration 2.0 — 4.0 — 4.0 — ns tPTOE/DIS Input to output local product term output enable/disable — 7.00 — 9.0 — 10.5 ns — 9.00 — 10.3 — 12.0 ns tGPTOE/DIS Input to output global product term output enable/disable ns ns tGOE/DIS Global OE input to output enable/disable — 5.00 — 7.0 — 8.0 ns tCW Global clock width, high or low 2.2 — 3.3 — 4.0 — ns tGW Global gate width low (for low transparent) or high (for high transparent) 2.2 — 3.3 — 4.0 — ns tWIR Input register clock width, high or low 2.2 — 3.3 — 4.0 — ns fMAX4 Clock frequency with internal feedback 227 — 168 — 125 — MHz fMAX (Ext.) Clock frequency with external feedback, [1/ (tS + tCO)] 156 — 111 — 86 — MHz Timing v.3.1 1. 2. 3. 4. 5. Timing numbers are based on default LVCMOS 1.8 I/O buffers. Use timing adjusters provided to calculate other standards. Measured using standard switching circuit, assuming GRP loading of 1 and 1 output switching. Pulse widths and clock widths less than minimum will cause unknown behavior. Standard 16-bit counter using GRP feedback. Only available in industrial grade. 19 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Timing Model The task of determining the timing through the ispMACH 4000 family, like any CPLD, is relatively simple. The timing model provided in Figure 10 shows the specific delay paths. Once the implementation of a given function is determined either conceptually or from the software report file, the delay path of the function can easily be determined from the timing model. The Lattice design tools report the timing delays based on the same timing model for a particular design. Note that the internal timing parameters are given for reference only, and are not tested. The external timing parameters are tested and guaranteed for every device. For more information on the timing model and usage, please refer to Technical Note TN1004: ispMACH 4000 Timing Model Design and Usage Guidelines. Figure 10. ispMACH 4000 Timing Model Routing/GLB Delays From Feedback tPDb tFBK tPDi IN SCLK tIN tIOI tROUTE tBLA tMCELL tEXP DATA Q tINREG tINDIO tGCLK_IN tIOI OE tBUF tIOO tEN tDIS Out In/Out Delays tPTCLK tBCLK C.E. tPTSR tBSR S/R MC Reg. Control Delays tORP Feedback Register/Latch Delays tGPTOE tPTOE tGOE tIOI In/Out Delays Note: Italicized items are optional delay adders. 20 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C Internal Timing Parameters Over Recommended Operating Conditions -25 Parameter Description -27 -3 -35 Min. Max. Min. Max. Min. Max. Min. Max. Units In/Out Delays tIN Input Buffer Delay — 0.60 — 0.60 — 0.70 — 0.70 ns tGOE Global OE Pin Delay — 2.04 — 2.54 — 3.04 — 3.54 ns tGCLK_IN Global Clock Input Buffer Delay — 0.78 — 1.28 — 1.28 — 1.28 ns tBUF Delay through Output Buffer — 0.85 — 0.85 — 0.85 — 0.85 ns tEN Output Enable Time — 0.96 — 0.96 — 0.96 — 0.96 ns tDIS Output Disable Time — 0.96 — 0.96 — 0.96 — 0.96 ns Routing/GLB Delays tROUTE Delay through GRP — 0.61 — 0.81 — 1.01 — 1.01 ns tMCELL Macrocell Delay — 0.45 — 0.55 — 0.55 — 0.65 ns tINREG Input Buffer to Macrocell Register Delay — 0.11 — 0.31 — 0.31 — 0.31 ns tFBK Internal Feedback Delay — 0.00 — 0.00 — 0.00 — 0.00 ns tPDb 5-PT Bypass Propagation Delay — 0.44 — 0.44 — 0.44 — 0.94 ns tPDi Macrocell Propagation Delay — 0.64 — 0.64 — 0.64 — 0.94 ns Register/Latch Delays tS D-Register Setup Time (Global Clock) 0.92 — 1.12 — 1.02 — 0.92 — ns tS_PT D-Register Setup Time (Product Term Clock) 1.42 — 1.32 — 1.32 — 1.32 — ns tST T-Register Setup Time (Global Clock) 1.12 — 1.32 — 1.22 — 1.12 — ns tST_PT T-Register Setup Time (Product Term Clock) 1.42 — 1.32 — 1.32 — 1.32 — ns tH D-Register Hold Time 0.88 — 0.68 — 0.98 — 1.08 — ns tHT T-Register Hold Time 0.88 — 0.68 — 0.98 — 1.08 — ns tSIR D-Input Register Setup Time (Global Clock) 0.82 — 1.37 — 1.27 — 1.27 — ns tSIR_PT D-Input Register Setup Time (Product Term Clock) 1.45 — 1.45 — 1.45 — 1.45 — ns tHIR D-Input Register Hold Time (Global Clock) 0.88 — 0.63 — 0.73 — 0.73 — ns tHIR_PT D-Input Register Hold Time (Product Term Clock) 0.88 — 0.63 — 0.73 — 0.73 — ns tCOi Register Clock to Output/Feedback MUX Time — 0.52 — 0.52 — 0.52 — 0.52 ns tCES Clock Enable Setup Time 2.25 — 2.25 — 2.25 — 2.25 — ns tCEH Clock Enable Hold Time 1.88 — 1.88 — 1.88 — 1.88 — ns tSL Latch Setup Time (Global Clock) 0.92 — 1.12 — 1.02 — 0.92 — ns tSL_PT Latch Setup Time (Product Term Clock) 1.42 — 1.32 — 1.32 — 1.32 — ns tHL Latch Hold Time 1.17 — 1.17 — 1.17 — 1.17 — ns tGOi Latch Gate to Output/Feedback MUX Time — 0.33 — 0.33 — 0.33 — 0.33 ns tPDLi Propagation Delay through Transparent Latch to Output/Feedback MUX — 0.25 — 0.25 — 0.25 — 0.25 ns tSRi Asynchronous Reset or Set to Output/ Feedback MUX Delay — 0.28 — 0.28 — 0.28 — 0.28 ns 21 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C Internal Timing Parameters (Cont.) Over Recommended Operating Conditions -25 Parameter tSRR Description Asynchronous Reset or Set Recovery Delay -27 -3 -35 Min. Max. Min. Max. Min. Max. Min. Max. Units — 1.67 — 1.67 — 1.67 — 1.67 ns — 1.12 — 1.12 — 1.12 — 1.12 ns Control Delays tBCLK GLB PT Clock Delay tPTCLK Macrocell PT Clock Delay — 0.87 — 0.87 — 0.87 — 0.87 ns tBSR Block PT Set/Reset Delay — 1.83 — 1.83 — 1.83 — 1.83 ns tPTSR Macrocell PT Set/Reset Delay — 1.11 — 1.41 — 1.51 — 1.61 ns tGPTOE Global PT OE Delay — 2.83 — 4.13 — 5.33 — 5.33 ns tPTOE Macrocell PT OE Delay — 1.83 — 2.13 — 2.33 — 2.83 ns Timing v.3.1 Note: Internal Timing Parameters are not tested and are for reference only. Refer to Timing Model in this data sheet for further details. 22 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C Internal Timing Parameters (Cont.) Over Recommended Operating Conditions -5 Parameter Description -101 -75 Min. Max. Min. Max. Min. Max. Units In/Out Delays tIN Input Buffer Delay — 0.95 — 1.50 — 2.00 ns tGOE Global OE Pin Delay — 4.04 — 6.04 — 7.04 ns tGCLK_IN Global Clock Input Buffer Delay — 1.83 — 2.28 — 3.28 ns tBUF Delay through Output Buffer — 1.00 — 1.50 — 1.50 ns tEN Output Enable Time — 0.96 — 0.96 — 0.96 ns tDIS Output Disable Time — 0.96 — 0.96 — 0.96 ns Routing/GLB Delays tROUTE Delay through GRP — 1.51 — 2.26 — 3.26 ns tMCELL Macrocell Delay — 1.05 — 1.45 — 1.95 ns tINREG Input Buffer to Macrocell Register Delay — 0.56 — 0.96 — 1.46 ns tFBK Internal Feedback Delay — 0.00 — 0.00 — 0.00 ns tPDb 5-PT Bypass Propagation Delay — 1.54 — 2.24 — 3.24 ns tPDi Macrocell Propagation Delay — 0.94 — 1.24 — 1.74 ns 1.32 — 1.57 — 1.57 — ns Register/Latch Delays tS D-Register Setup Time (Global Clock) tS_PT D-Register Setup Time (Product Term Clock) 1.32 — 1.32 — 1.32 — ns tST T-Register Setup Time (Global Clock) 1.52 — 1.77 — 1.77 — ns tST_PT T-Register Setup Time (Product Term Clock) 1.32 — 1.32 — 1.32 — ns tH D-Register Hold Time 1.68 — 2.93 — 3.93 — ns tHT T-Register Hold Time 1.68 — 2.93 — 3.93 — ns tSIR D-Input Register Setup Time (Global Clock) 1.52 — 1.57 — 1.57 — ns tSIR_PT D-Input Register Setup Time (Product Term Clock) 1.45 — 1.45 — 1.45 — ns tHIR D-Input Register Hold Time (Global Clock) 0.68 — 1.18 — 1.18 — ns tHIR_PT D-Input Register Hold Time (Product Term Clock) 0.68 — 1.18 — 1.18 — ns tCOi Register Clock to Output/Feedback MUX Time — 0.52 — 0.67 — 1.17 ns tCES Clock Enable Setup Time 2.25 — 2.25 — 2.25 — ns tCEH Clock Enable Hold Time 1.88 — 1.88 — 1.88 — ns tSL Latch Setup Time (Global Clock) 1.32 — 1.57 — 1.57 — ns tSL_PT Latch Setup Time (Product Term Clock) 1.32 — 1.32 — 1.32 — ns tHL Latch Hold Time 1.17 — 1.17 — 1.17 — ns tGOi Latch Gate to Output/Feedback MUX Time — 0.33 — 0.33 — 0.33 ns tPDLi Propagation Delay through Transparent Latch to Output/ Feedback MUX — 0.25 — 0.25 — 0.25 ns tSRi Asynchronous Reset or Set to Output/Feedback MUX Delay — 0.28 — 0.28 — 0.28 ns tSRR Asynchronous Reset or Set Recovery Delay — 1.67 — 1.67 — 1.67 ns Control Delays tBCLK GLB PT Clock Delay — 1.12 — 1.12 — 0.62 ns tPTCLK Macrocell PT Clock Delay — 0.87 — 0.87 — 0.87 ns tBSR GLB PT Set/Reset Delay — 1.83 — 1.83 — 1.83 ns tPTSR Macrocell PT Set/Reset Delay — 2.51 — 3.41 — 3.41 ns 23 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C Internal Timing Parameters (Cont.) Over Recommended Operating Conditions -5 Parameter Description -101 -75 Min. Max. Min. Max. Min. Max. Units tGPTOE Global PT OE Delay — 5.58 — 5.58 — 5.78 ns tPTOE Macrocell PT OE Delay — 3.58 — 4.28 — 4.28 ns Timing v.3.1 Note: Internal Timing Parameters are not tested and are for reference only. Refer to Timing Model in this data sheet for further details. 1. Only available in industrial grade. 24 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C Timing Adders1 Adder Type Base Parameter -25 Description -27 -3 -35 Min. Max. Min. Max. Min. Max. Min. — 0.95 — 1.00 — 1.00 — Max. Units Optional Delay Adders tINDIO tEXP tINREG tMCELL tORP tBLA — tROUTE Input register delay Product term expander delay — 0.33 — Output routing pool delay — 0.05 — Additional block loading adder — 0.03 — 0.33 — 0.05 — 0.05 — 0.33 — 0.05 — 0.05 — 1.00 0.33 ns ns 0.05 ns 0.05 ns tIOI Input Adjusters LVTTL_in tIN, tGCLK_IN, tGOE Using LVTTL standard — 0.60 — 0.60 — 0.60 — 0.60 ns LVCMOS33_in tIN, tGCLK_IN, tGOE Using LVCMOS 3.3 standard — 0.60 — 0.60 — 0.60 — 0.60 ns LVCMOS25_in tIN, tGCLK_IN, tGOE Using LVCMOS 2.5 standard — 0.60 — 0.60 — 0.60 — 0.60 ns LVCMOS18_in tIN, tGCLK_IN, tGOE Using LVCMOS 1.8 standard — 0.00 — 0.00 — 0.00 — 0.00 ns PCI_in tIN, tGCLK_IN, tGOE Using PCI compatible input — 0.60 — 0.60 — 0.60 — 0.60 ns tBUF, tEN, tDIS Output configured as TTL buffer — 0.20 — 0.20 — 0.20 — 0.20 ns LVCMOS33_out tBUF, tEN, tDIS Output configured as 3.3V buffer — 0.20 — 0.20 — 0.20 — 0.20 ns LVCMOS25_out tBUF, tEN, tDIS Output configured as 2.5V buffer — 0.10 — 0.10 — 0.10 — 0.10 ns LVCMOS18_out tBUF, tEN, tDIS Output configured as 1.8V buffer — 0.00 — 0.00 — 0.00 — 0.00 ns PCI_out tBUF, tEN, tDIS Output configured as PCI compatible buffer — 0.20 — 0.20 — 0.20 — 0.20 ns Slow Slew tBUF, tEN Output configured for slow slew rate — 1.00 — 1.00 — 1.00 — 1.00 ns tIOO Output Adjusters LVTTL_out Timing v.3.1 Note: Open drain timing is the same as corresponding LVCMOS timing. 1. Refer to Technical Note TN1004: ispMACH 4000 Timing Model Design and Usage Guidelines for information regarding use of these adders. 25 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C Timing Adders1 Adder Type Base Parameter -5 Description -102 -75 Min. Max. Min. Max. Min. — 1.00 — 1.00 — Max. Units Optional Delay Adders tINDIO tINREG tEXP tMCELL — tORP tBLA tROUTE Input register delay 1.00 ns Product term expander delay — 0.33 — 0.33 — 0.33 ns Output routing pool delay — 0.05 — 0.05 — 0.05 ns Additional block loading adder — 0.05 — 0.05 — 0.05 ns tIOI Input Adjusters LVTTL_in tIN, tGCLK_IN, tGOE Using LVTTL standard — 0.60 — 0.60 — 0.60 ns LVCMOS33_in tIN, tGCLK_IN, tGOE Using LVCMOS 3.3 standard — 0.60 — 0.60 — 0.60 ns LVCMOS25_in tIN, tGCLK_IN, tGOE Using LVCMOS 2.5 standard — 0.60 — 0.60 — 0.60 ns LVCMOS18_in tIN, tGCLK_IN, tGOE Using LVCMOS 1.8 standard — 0.00 — 0.00 — 0.00 ns PCI_in tIN, tGCLK_IN, tGOE Using PCI compatible input — 0.60 — 0.60 — 0.60 ns — 0.20 — 0.20 — 0.20 ns LVCMOS33_out tBUF, tEN, tDIS Output configured as 3.3V buffer — 0.20 — 0.20 — 0.20 ns LVCMOS25_out tBUF, tEN, tDIS Output configured as 2.5V buffer — 0.10 — 0.10 — 0.10 ns LVCMOS18_out tBUF, tEN, tDIS Output configured as 1.8V buffer tIOO Output Adjusters LVTTL_out tBUF, tEN, tDIS Output configured as TTL buffer — 0.00 — 0.00 — 0.00 ns PCI_out Output configured as PCI compatible tBUF, tEN, tDIS buffer — 0.20 — 0.20 — 0.20 ns Slow Slew tBUF, tEN — 1.00 — 1.00 — 1.00 ns Output configured for slow slew rate Timing v.3.1 Note: Open drain timing is the same as corresponding LVCMOS timing. 1. Refer to Technical Note TN1004: ispMACH 4000 Timing Model Design and Usage Guidelines for information regarding use of these adders. 2. Only available in industrial grade. 26 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Boundary Scan Waveforms and Timing Specifications Symbol Parameter Min. Max. Units tBTCP TCK [BSCAN test] clock cycle 40 — ns tBTCH TCK [BSCAN test] pulse width high 20 — ns tBTCL TCK [BSCAN test] pulse width low 20 — ns tBTSU TCK [BSCAN test] setup time 8 — ns tBTH TCK [BSCAN test] hold time 10 — ns tBRF TCK [BSCAN test] rise and fall time 50 — mV/ns tBTCO TAP controller falling edge of clock to valid output — 10 ns tBTOZ TAP controller falling edge of clock to data output disable — 10 ns tBTVO TAP controller falling edge of clock to data output enable — 10 ns tBTCPSU BSCAN test Capture register setup time 8 — ns tBTCPH BSCAN test Capture register hold time 10 — ns tBTUCO BSCAN test Update reg, falling edge of clock to valid output — 25 ns tBTUOZ BSCAN test Update reg, falling edge of clock to output disable — 25 ns tBTUOV BSCAN test Update reg, falling edge of clock to output enable — 25 ns 27 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Power Consumption ispMACH 4000V/B Typical ICC vs. Frequency ispMACH 4000C Typical ICC vs. Frequency 4512C 300 300 4512V/B 250 250 4384C ICC (mA) ICC (mA) 4384V/B 200 4256C 150 100 200 150 4256V/B 100 4128C 50 4128V/B 50 4064C 4064V/B 4032V/B 4032C 0 0 50 100 150 200 250 300 350 0 0 400 Frequency (MHz) 50 100 150 200 250 300 350 400 Frequency (MHz) Note: The devices are configured with maximum number of 16-bit counters, typical current at 1.8V, 25°C. Note: The devices are configured with maximum number of 16-bit counters, typical current at 3.3V, 2.5V, 25°C. Power Estimation Coefficients Device A B ispMACH 4032V/B 11.3 0.010 ispMACH 4032C 1.3 0.010 ispMACH 4064V/B 11.5 0.010 ispMACH 4064C 1.5 0.010 ispMACH 4128V/B 11.5 0.011 ispMACH 4128C 1.5 0.011 ispMACH 4256V/B 12 0.011 ispMACH 4256C 2 0.011 ispMACH 4384V/B 12.5 0.013 ispMACH 4384C 2.5 0.013 ispMACH 4512V/B 13 0.013 ispMACH 4512C 3 0.013 Note: For further information about the use of these coefficients, refer to Technical Note TN1005, Power Estimation in ispMACH 4000V/B/C Devices. 28 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Switching Test Conditions Figure 11 shows the output test load that is used for AC testing. The specific values for resistance, capacitance, voltage, and other test conditions are shown in Table 9. Figure 11. Output Test Load, LVTTL and LVCMOS Standards VCCO R1 Test Point DUT R2 CL 0213A/ispm4k Table 9. Test Fixture Required Components Test Condition LVCMOS I/O, (L -> H, H -> L) R1 CL1 R2 Timing Ref. VCCO LVCMOS 3.3 = 1.5V LVCMOS 3.3 = 3.0V LVCMOS 2.5 = VCCO/2 LVCMOS 2.5 = 2.3V 106Ω 106Ω 35pF LVCMOS 1.8 = VCCO/2 LVCMOS 1.8 = 1.65V 106Ω 35pF 1.5V 3.0V LVCMOS I/O (Z -> H) ∞ LVCMOS I/O (Z -> L) 106Ω ∞ 35pF 1.5V 3.0V LVCMOS I/O (H -> Z) ∞ 106Ω 5pF VOH - 0.3 3.0V LVCMOS I/O (L -> Z) 106Ω ∞ 5pF VOL + 0.3 3.0V 1. CL includes test fixtures and probe capacitance. 29 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Signal Descriptions Signal Names Description TMS Input – This pin is the IEEE 1149.1 Test Mode Select input, which is used to control the state machine TCK Input – This pin is the IEEE 1149.1 Test Clock input pin, used to clock through the state machine TDI Input – This pin is the IEEE 1149.1 Test Data In pin, used to load data TDO Output – This pin is the IEEE 1149.1 Test Data Out pin used to shift data out GOE0, GOE1 Input – These pins are the Global Output Enable Input pins GND Ground NC Not Connected VCC The power supply pins for logic core CLK0/I, CLK1/I, CLK2/I, CLK3/I These pins are configured to be either CLK input or as an input VCCO0, VCCO1 The power supply pins for each I/O bank Input/Output1 – These are the general purpose I/O used by the logic array. y is GLB reference (alpha) and z is macrocell reference (numeric). z: 0-15 yzz ispMACH 4032 y: A-B ispMACH 4064 y: A-D ispMACH 4128 y: A-H ispMACH 4256 y: A-P ispMACH 4384 y: A-P, AX-HX ispMACH 4512 y: A-P, AX-PX 1. In some packages, certain I/O are only available for use as inputs. See the signal connections table for details. 30 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V/B/C Power Supply and NC Connections1 Signal 44 TQFP 48 TQFP 100 TQFP 128 TQFP 176 TQFP 256 fpBGA2, 3 VCC 11, 33 12, 36 25, 40, 75, 90 32, 51, 96, 115 42, 69, 88, 130, 157, 176 B2, B15, G8, G9, K8, K9, R2, R15 VCCO0 6 6 13, 33, 95 3, 17, 30, 41, 122 4, 22, 40, 56, 166 D6, F4, H7, J7, L4, N6 VCCO1 28 30 45, 63, 83 58, 67, 81, 94, 105 78, 92, 110, D11, F13, H10, J10, L13, N11 128, 144 GND 12, 34 13, 37 1, 26, 51, 76 1, 33, 65, 97 2, 46, 65, A1, A16, C6, C11, F3, F14, G7, G10, H8, 90, 134, 153 H9, J8, J9, K7, K10, L3, L14, P6, P11, T1, 7, 18, 32, 96 10, 24, 40, 13, 31, 55, T16 GND (Bank 0) 5 5 113, 123 155, 167 GND (Bank 1) 27 29 46, 57, 68, 82 49, 59, 74, 88, 104 67, 79, 101, 119, 143 NC — — — 1, 43, 44, 4256V/B/C, 128 I/O: A4, A5, A6, A11, 45, 89, 131, A12, A13, A15, B5, B6, B11, B12, B14, 132, 133 C7, D1, D4, D5, D10, D12, D16, E1, E2, E4, E5, E7, E10, E13, E14, E15, E16, F1, F2, F15, F16, G1, G4, G5, G6, G12, G13, G14, J11, K3, K4, K15, L1, L2, L12, L15, L16, M1, M2, M3, M4, M5, M12, M13, M15, M16, N1, N2, N7, N10, N12, N14, P5, P12, R4, R5, R6, R11, R12, R16, T2, T4, T5, T6, T11, T12, T13, T15 — 4256V/B/C, 160 I/O: A5, A12, A15, B5, B6, B11, B12, B14, D4, D5, D12, E1, E4, E5, E13, E15, E16, F1, F2, F15, G1, G5, G12, G14, L1, L2, L12, L15, L16, M1, M2, M3, M12, M16, N1, N12, N14, P5, R4, R5, R6, R11, R12, R16, T4, T5, T12, T15 4384V/B/C: B5, B12, D5, D12, E1, E15, E16, F2, L12, M1, M2, M16, N12, R5, R12, T4 4512V/B/C: None 1. All grounds must be electrically connected at the board level. However, for the purposes of I/O current loading, grounds are associated with the bank shown. 2. Internal GNDs and I/O GNDs (Bank 0/1) are connected inside package. 3. VCCO balls connect to two power planes within the package, one for VCCO0 and one for VCCO1. 31 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4032V/B/C Logic Signal Connections: 44-Pin TQFP ispMACH 4032V/B/C Pin Number Bank Number GLB/MC/Pad ORP 1 - TDI - 2 0 A5 A^5 3 0 A6 A^6 4 0 A7 A^7 5 0 GND (Bank 0) - 6 0 VCCO (Bank 0) - 7 0 A8 A^8 8 0 A9 A^9 9 0 A10 A^10 10 - TCK - 11 - VCC - 12 - GND - 13 0 A12 A^12 14 0 A13 A^13 15 0 A14 A^14 16 0 A15 A^15 17 1 CLK2/I - 18 1 B0 B^0 19 1 B1 B^1 20 1 B2 B^2 21 1 B3 B^3 22 1 B4 B^4 23 - TMS - 24 1 B5 B^5 25 1 B6 B^6 26 1 B7 B^7 27 1 GND (Bank 1) - 28 1 VCCO (Bank 1) - 29 1 B8 B^8 30 1 B9 B^9 31 1 B10 B^10 32 - TDO - 33 - VCC - 34 - GND - 35 1 B12 B^12 36 1 B13 B^13 37 1 B14 B^14 38 1 B15/GOE1 B^15 39 0 CLK0/I - 40 0 A0/GOE0 A^0 41 0 A1 A^1 42 0 A2 A^2 43 0 A3 A^3 32 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4032V/B/C Logic Signal Connections: 44-Pin TQFP (Cont.) ispMACH 4032V/B/C Pin Number Bank Number GLB/MC/Pad ORP 44 0 A4 A^4 ispMACH 4032V/B/C Logic Signal Connections: 48-Pin TQFP ispMACH 4032V/B/C Pin Number Bank Number GLB/MC/Pad ORP 1 - TDI - 2 0 A5 A^5 3 0 A6 A^6 4 0 A7 A^7 5 0 GND (Bank 0) - 6 0 VCCO (Bank 0) - 7 0 A8 A^8 8 0 A9 A^9 9 0 A10 A^10 10 0 A11 A^11 11 - TCK - 12 - VCC - 13 - GND - 14 0 A12 A^12 15 0 A13 A^13 16 0 A14 A^14 17 0 A15 A^15 18 0 CLK1/I - 19 1 CLK2/I - 20 1 B0 B^0 21 1 B1 B^1 22 1 B2 B^2 23 1 B3 B^3 24 1 B4 B^4 25 - TMS - 26 1 B5 B^5 27 1 B6 B^6 28 1 B7 B^7 29 1 GND (Bank 1) - 30 1 VCCO (Bank 1) - 31 1 B8 B^8 32 1 B9 B^9 33 1 B10 B^10 34 1 B11 B^11 35 - TDO - 36 - VCC - 33 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4032V/B/C Logic Signal Connections: 48-Pin TQFP (Cont.) ispMACH 4032V/B/C Pin Number Bank Number GLB/MC/Pad ORP 37 - GND - 38 1 B12 B^12 39 1 B13 B^13 40 1 B14 B^14 41 1 B15/GOE1 B^15 42 1 CLK3/I - 43 0 CLK0/I - 44 0 A0/GOE0 A^0 45 0 A1 A^1 46 0 A2 A^2 47 0 A3 A^3 48 0 A4 A^4 ispMACH 4064V/B/C, 4128V/B/C, 4256V/B/C Logic Signal Connections: 100-Pin TQFP ispMACH 4064V/B/C ispMACH 4128V/B/C ispMACH 4256V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 1 - GND - GND - GND - 2 - TDI - TDI - TDI - 3 0 A8 A^8 B0 B^0 C12 C^6 4 0 A9 A^9 B2 B^2 C10 C^5 5 0 A10 A^10 B4 B^4 C6 C^3 6 0 A11 A^11 B6 B^6 C2 C^1 7 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 8 0 A12 A^12 B8 B^8 D12 D^6 9 0 A13 A^13 B10 B^10 D10 D^5 10 0 A14 A^14 B12 B^12 D6 D^3 11 0 A15 A^15 B13 B^13 D4 D^2 12* 0 I - I - I - 13 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 14 0 B15 B^15 C14 C^14 E4 E^2 15 0 B14 B^14 C12 C^12 E6 E^3 16 0 B13 B^13 C10 C^10 E10 E^5 17 0 B12 B^12 C8 C^8 E12 E^6 18 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 19 0 B11 B^11 C6 C^6 F2 F^1 20 0 B10 B^10 C5 C^5 F6 F^3 21 0 B9 B^9 C4 C^4 F10 F^5 22 0 B8 B^8 C2 C^2 F12 F^6 23* 0 I - I - I - 24 - TCK - TCK - TCK - 34 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4064V/B/C, 4128V/B/C, 4256V/B/C Logic Signal Connections: 100-Pin TQFP (Cont.) ispMACH 4064V/B/C ispMACH 4128V/B/C ispMACH 4256V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 25 - VCC - VCC - VCC - 26 - GND - GND - GND - 27* 0 I - I - I - 28 0 B7 B^7 D13 D^13 G12 G^6 29 0 B6 B^6 D12 D^12 G10 G^5 30 0 B5 B^5 D10 D^10 G6 G^3 31 0 B4 B^4 D8 D^8 G2 G^1 32 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 33 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 34 0 B3 B^3 D6 D^6 H12 H^6 35 0 B2 B^2 D4 D^4 H10 H^5 36 0 B1 B^1 D2 D^2 H6 H^3 37 0 B0 B^0 D0 D^0 H2 H^1 38 0 CLK1/I - CLK1/I - CLK1/I - 39 1 CLK2/I - CLK2/I - CLK2/I - 40 - VCC - VCC - VCC - 41 1 C0 C^0 E0 E^0 I2 I^1 42 1 C1 C^1 E2 E^2 I6 I^3 43 1 C2 C^2 E4 E^4 I10 I^5 44 1 C3 C^3 E6 E^6 I12 I^6 45 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 46 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 47 1 C4 C^4 E8 E^8 J2 J^1 48 1 C5 C^5 E10 E^10 J6 J^3 49 1 C6 C^6 E12 E^12 J10 J^5 50 1 C7 C^7 E14 E^14 J12 J^6 51 - GND - GND - GND - 52 - TMS - TMS - TMS - 53 1 C8 C^8 F0 F^0 K12 K^6 54 1 C9 C^9 F2 F^2 K10 K^5 55 1 C10 C^10 F4 F^4 K6 K^3 56 1 C11 C^11 F6 F^6 K2 K^1 57 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 58 1 C12 C^12 F8 F^8 L12 L^6 59 1 C13 C^13 F10 F^10 L10 L^5 60 1 C14 C^14 F12 F^12 L6 L^3 61 1 C15 C^15 F13 F^13 L4 L^2 62* 1 I - I - I - 63 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 64 1 D15 D^15 G14 G^14 M4 M^2 65 1 D14 D^14 G12 G^12 M6 M^3 66 1 D13 D^13 G10 G^10 M10 M^5 35 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4064V/B/C, 4128V/B/C, 4256V/B/C Logic Signal Connections: 100-Pin TQFP (Cont.) ispMACH 4064V/B/C ispMACH 4128V/B/C ispMACH 4256V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 67 1 D12 D^12 G8 G^8 M12 M^6 68 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 69 1 D11 D^11 G6 G^6 N2 N^1 70 1 D10 D^10 G5 G^5 N6 N^3 71 1 D9 D^9 G4 G^4 N10 N^5 72 1 D8 D^8 G2 G^2 N12 N^6 73* 1 I - I - I - 74 - TDO - TDO - TDO - 75 - VCC - VCC - VCC - 76 - GND - GND - GND - 77* 1 I - I - I - 78 1 D7 D^7 H13 H^13 O12 O^6 79 1 D6 D^6 H12 H^12 O10 O^5 80 1 D5 D^5 H10 H^10 O6 O^3 81 1 D4 D^4 H8 H^8 O2 O^1 82 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 83 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 84 1 D3 D^3 H6 H^6 P12 P^6 85 1 D2 D^2 H4 H^4 P10 P^5 86 1 D1 D^1 H2 H^2 P6 P^3 87 1 D0/GOE1 D^0 H0/GOE1 H^0 P2/OE1 P^1 88 1 CLK3/I - CLK3/I - CLK3/I - 89 0 CLK0/I - CLK0/I - CLK0/I - 90 - VCC - VCC - VCC - 91 0 A0/GOE0 A^0 A0/GOE0 A^0 A2/GOE0 A^1 92 0 A1 A^1 A2 A^2 A6 A^3 93 0 A2 A^2 A4 A^4 A10 A^5 94 0 A3 A^3 A6 A^6 A12 A^6 95 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 96 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 97 0 A4 A^4 A8 A^8 B2 B^1 98 0 A5 A^5 A10 A^10 B6 B^3 99 0 A6 A^6 A12 A^12 B10 B^5 100 0 A7 A^7 A14 A^14 B12 B^6 *This pin is input only. 36 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4128V/B/C Logic Signal Connections: 128-Pin TQFP ispMACH 4128V/B/C Pin Number Bank Number GLB/MC/Pad ORP 1 0 GND - 2 0 TDI - 3 0 VCCO (Bank 0) - 4 0 B0 B^0 5 0 B1 B^1 6 0 B2 B^2 7 0 B4 B^4 8 0 B5 B^5 9 0 B6 B^6 10 0 GND (Bank 0) - 11 0 B8 B^8 12 0 B9 B^9 13 0 B10 B^10 14 0 B12 B^12 15 0 B13 B^13 16 0 B14 B^14 17 0 VCCO (Bank 0) - 18 0 C14 C^14 19 0 C13 C^13 20 0 C12 C^12 21 0 C10 C^10 22 0 C9 C^9 23 0 C8 C^8 24 0 GND (Bank 0) - 25 0 C6 C^6 26 0 C5 C^5 27 0 C4 C^4 28 0 C2 C^2 29 0 C0 C^0 30 0 VCCO (Bank 0) - 31 0 TCK - 32 0 VCC - 33 0 GND - 34 0 D14 D^14 35 0 D13 D^13 36 0 D12 D^12 37 0 D10 D^10 38 0 D9 D^9 39 0 D8 D^8 40 0 GND (Bank 0) - 41 0 VCCO (Bank 0) - 42 0 D6 D^6 43 0 D5 D^5 37 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4128V/B/C Logic Signal Connections: 128-Pin TQFP (Cont.) ispMACH 4128V/B/C Pin Number Bank Number GLB/MC/Pad ORP 44 0 D4 D^4 45 0 D2 D^2 46 0 D1 D^1 47 0 D0 D^0 48 0 CLK1/I - 49 1 GND (Bank 1) - 50 1 CLK2/I - 51 1 VCC - 52 1 E0 E^0 53 1 E1 E^1 54 1 E2 E^2 55 1 E4 E^4 56 1 E5 E^5 57 1 E6 E^6 58 1 VCCO (Bank 1) - 59 1 GND (Bank 1) - 60 1 E8 E^8 61 1 E9 E^9 62 1 E10 E^10 63 1 E12 E^12 64 1 E14 E^14 65 1 GND - 66 1 TMS - 67 1 VCCO (Bank 1) - 68 1 F0 F^0 69 1 F1 F^1 70 1 F2 F^2 71 1 F4 F^4 72 1 F5 F^5 73 1 F6 F^6 74 1 GND (Bank 1) - 75 1 F8 F^8 76 1 F9 F^9 77 1 F10 F^10 78 1 F12 F^12 79 1 F13 F^13 80 1 F14 F^14 81 1 VCCO (Bank 1) - 82 1 G14 G^14 83 1 G13 G^13 84 1 G12 G^12 85 1 G10 G^10 86 1 G9 G^9 38 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4128V/B/C Logic Signal Connections: 128-Pin TQFP (Cont.) ispMACH 4128V/B/C Pin Number Bank Number GLB/MC/Pad ORP 87 1 G8 G^8 88 1 GND (Bank 1) - 89 1 G6 G^6 90 1 G5 G^5 91 1 G4 G^4 92 1 G2 G^2 93 1 G0 G^0 94 1 VCCO (Bank 1) - 95 1 TDO - 96 1 VCC - 97 1 GND - 98 1 H14 H^14 99 1 H13 H^13 100 1 H12 H^12 101 1 H10 H^10 102 1 H9 H^9 103 1 H8 H^8 104 1 GND (Bank 1) - 105 1 VCCO (Bank 1) - 106 1 H6 H^6 107 1 H5 H^5 108 1 H4 H^4 109 1 H2 H^2 110 1 H1 H^1 111 1 H0/GOE1 H^0 112 1 CLK3/I - 113 0 GND (Bank 0) - 114 0 CLK0/I - 115 0 VCC - 116 0 A0/GOE0 A^0 117 0 A1 A^1 118 0 A2 A^2 119 0 A4 A^4 120 0 A5 A^5 121 0 A6 A^6 122 0 VCCO (Bank 0) - 123 0 GND (Bank 0) - 124 0 A8 A^8 125 0 A9 A^9 126 0 A10 A^10 127 0 A12 A^12 128 0 A14 A^14 39 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C, Logic Signal Connections: 176-Pin TQFP ispMACH 4256V/B/C ispMACH 4384V/B/C ispMACH 4512V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 1 - NC - NC - NC - 2 - GND - GND - GND - 3 - TDI - TDI - TDI - 4 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 5 0 C14 C^7 C14 C^7 C14 C^7 6 0 C12 C^6 C12 C^6 C12 C^6 7 0 C10 C^5 C10 C^5 C10 C^5 8 0 C8 C^4 C8 C^4 C8 C^4 9 0 C6 C^3 C6 C^3 C6 C^3 10 0 C4 C^2 C4 C^2 C4 C^2 11 0 C2 C^1 C2 C^1 C2 C^1 12 0 C0 C^0 C0 C^0 C0 C^0 13 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 14 0 D14 D^7 E14 E^7 G14 G^7 15 0 D12 D^6 E12 E^6 G12 G^6 16 0 D10 D^5 E10 E^5 G10 G^5 17 0 D8 D^4 E8 E^4 G8 G^4 18 0 D6 D^3 E6 E^3 G6 G^3 19 0 D4 D^2 E4 E^2 G4 G^2 20 0 D2 D^1 E2 E^1 G2 G^1 21 0 D0 D^0 E0 E^0 G0 G^0 22 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 23 0 E0 E^0 H0 H^0 J0 J^0 24 0 E2 E^1 H2 H^1 J2 J^1 25 0 E4 E^2 H4 H^2 J4 J^2 26 0 E6 E^3 H6 H^3 J6 J^3 27 0 E8 E^4 H8 H^4 J8 J^4 28 0 E10 E^5 H10 H^5 J10 J^5 29 0 E12 E^6 H12 H^6 J12 J^6 30 0 E14 E^7 H14 H^7 J14 J^7 31 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 32 0 F0 F^0 J0 J^0 N0 N^0 33 0 F2 F^1 J2 J^1 N2 N^1 34 0 F4 F^2 J4 J^2 N4 N^2 35 0 F6 F^3 J6 J^3 N6 N^3 36 0 F8 F^4 J8 J^4 N8 N^4 37 0 F10 F^5 J10 J^5 N10 N^5 38 0 F12 F^6 J12 J^6 N12 N^6 39 0 F14 F^7 J14 J^7 N14 N^7 40 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 41 - TCK - TCK - TCK - 42 - VCC - VCC - VCC - 40 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C, Logic Signal Connections: 176-Pin TQFP (Cont.) ispMACH 4256V/B/C ispMACH 4384V/B/C ispMACH 4512V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 43 - NC - NC - NC - 44 - NC - NC - NC - 45 - NC - NC - NC - 46 - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 47 0 G14 G^7 K14 K^7 O14 O^7 48 0 G12 G^6 K12 K^6 O12 O^6 49 0 G10 G^5 K10 K^5 O10 O^5 50 0 G8 G^4 K8 K^4 O8 O^4 51 0 G6 G^3 K6 K^3 O6 O^3 52 0 G4 G^2 K4 K^2 O4 O^2 53 0 G2 G^1 K2 K^1 O2 O^1 54 0 G0 G^0 K0 K^0 O0 O^0 55 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 56 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 57 0 H14 H^7 L14 L^7 P14 P^7 58 0 H12 H^6 L12 L^6 P12 P^6 59 0 H10 H^5 L10 L^5 P10 P^5 60 0 H8 H^4 L8 L^4 P8 P^4 61 0 H6 H^3 L6 L^3 P6 P^3 62 0 H4 H^2 L4 L^2 P4 P^2 63 0 H2 H^1 L2 L^1 P2 P^1 64 0 H0 H^0 L0 L^0 P0 P^0 65 - GND - GND - GND - 66 0 CLK1/I - CLK1/I - CLK1/I - 67 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 68 1 CLK2/I - CLK2/I - CLK2/I - 69 - VCC - VCC - VCC - 70 1 I0 I^0 M0 M^0 AX0 AX^0 71 1 I2 I^1 M2 M^1 AX2 AX^1 72 1 I4 I^2 M4 M^2 AX4 AX^2 73 1 I6 I^3 M6 M^3 AX6 AX^3 74 1 I8 I^4 M8 M^4 AX8 AX^4 75 1 I10 I^5 M10 M^5 AX10 AX^5 76 1 I12 I^6 M12 M^6 AX12 AX^6 77 1 I14 I^7 M14 M^7 AX14 AX^7 78 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 79 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 80 1 J0 J^0 N0 N^0 BX0 BX^0 81 1 J2 J^1 N2 N^1 BX2 BX^1 82 1 J4 J^2 N4 N^2 BX4 BX^2 83 1 J6 J^3 N6 N^3 BX6 BX^3 84 1 J8 J^4 N8 N^4 BX8 BX^4 41 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C, Logic Signal Connections: 176-Pin TQFP (Cont.) ispMACH 4256V/B/C ispMACH 4384V/B/C ispMACH 4512V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 85 1 J10 J^5 N10 N^5 BX10 BX^5 86 1 J12 J^6 N12 N^6 BX12 BX^6 87 1 J14 J^7 N14 N^7 BX14 BX^7 88 - VCC - VCC - VCC - 89 - NC - NC - NC - 90 - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 91 - TMS - TMS - TMS - 92 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 93 1 K14 K^7 O14 O^7 CX14 CX^7 94 1 K12 K^6 O12 O^6 CX12 CX^6 95 1 K10 K^5 O10 O^5 CX10 CX^5 96 1 K8 K^4 O8 O^4 CX8 CX^4 97 1 K6 K^3 O6 O^3 CX6 CX^3 98 1 K4 K^2 O4 O^2 CX4 CX^2 99 1 K2 K^1 O2 O^1 CX2 CX^1 100 1 K0 K^0 O0 O^0 CX0 CX^0 101 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 102 1 L14 L^7 AX14 AX^7 GX14 GX^7 103 1 L12 L^6 AX12 AX^6 GX12 GX^6 104 1 L10 L^5 AX10 AX^5 GX10 GX^5 105 1 L8 L^4 AX8 AX^4 GX8 GX^4 106 1 L6 L^3 AX6 AX^3 GX6 GX^3 107 1 L4 L^2 AX4 AX^2 GX4 GX^2 108 1 L2 L^1 AX2 AX^1 GX2 GX^1 109 1 L0 L^0 AX0 AX^0 GX0 GX^0 110 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 111 1 M0 M^0 DX0 DX^0 JX0 JX^0 112 1 M2 M^1 DX2 DX^1 JX2 JX^1 113 1 M4 M^2 DX4 DX^2 JX4 JX^2 114 1 M6 M^3 DX6 DX^3 JX6 JX^3 115 1 M8 M^4 DX8 DX^4 JX8 JX^4 116 1 M10 M^5 DX10 DX^5 JX10 JX^5 117 1 M12 M^6 DX12 DX^6 JX12 JX^6 118 1 M14 M^7 DX14 DX^7 JX14 JX^7 119 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 120 1 N0 N^0 FX0 FX^0 NX0 NX^0 121 1 N2 N^1 FX2 FX^1 NX2 NX^1 122 1 N4 N^2 FX4 FX^2 NX4 NX^2 123 1 N6 N^3 FX6 FX^3 NX6 NX^3 124 1 N8 N^4 FX8 FX^4 NX8 NX^4 125 1 N10 N^5 FX10 FX^5 NX10 NX^5 126 1 N12 N^6 FX12 FX^6 NX12 NX^6 42 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C, Logic Signal Connections: 176-Pin TQFP (Cont.) ispMACH 4256V/B/C ispMACH 4384V/B/C ispMACH 4512V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 127 1 N14 N^7 FX14 FX^7 NX14 NX^7 128 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 129 - TDO - TDO - TDO - 130 - VCC - VCC - VCC - 131 - NC - NC - NC - 132 - NC - NC - NC - 133 - NC - NC - NC - 134 - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 135 1 O14 O^7 GX14 GX^7 OX14 OX^7 136 1 O12 O^6 GX12 GX^6 OX12 OX^6 137 1 O10 O^5 GX10 GX^5 OX10 OX^5 138 1 O8 O^4 GX8 GX^4 OX8 OX^4 139 1 O6 O^3 GX6 GX^3 OX6 OX^3 140 1 O4 O^2 GX4 GX^2 OX4 OX^2 141 1 O2 O^1 GX2 GX^1 OX2 OX^1 142 1 O0 O^0 GX0 GX^0 OX0 OX^0 143 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - 144 1 VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - 145 1 P14 P^7 HX14 HX^7 PX14 PX^7 146 1 P12 P^6 HX12 HX^6 PX12 PX^6 147 1 P10 P^5 HX10 HX^5 PX10 PX^5 148 1 P8 P^4 HX8 HX^4 PX8 PX^4 149 1 P6 P^3 HX6 HX^3 PX6 PX^3 150 1 P4 P^2 HX4 HX^2 PX4 PX^2 151 1 P2/GOE1 P^1 HX2/GOE1 HX^1 PX2/GOE1 PX^1 152 1 P0 P^0 HX0 HX^0 PX0 PX^0 153 - GND - GND - GND - 154 1 CLK3/I - CLK3/I - CLK3/I - 155 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 156 0 CLK0/I - CLK0/I - CLK0/I - 157 - VCC - VCC - VCC - 158 0 A0 A^0 A0 A^0 A0 A^0 159 0 A2/GOE0 A^1 A2/GOE0 A^1 A2//GOE0 A^1 160 0 A4 A^2 A4 A^2 A4 A^2 161 0 A6 A^3 A6 A^3 A6 A^3 162 0 A8 A^4 A8 A^4 A8 A^4 163 0 A10 A^5 A10 A^5 A10 A^5 164 0 A12 A^6 A12 A^6 A12 A^6 165 0 A14 A^7 A14 A^7 A14 A^7 166 0 VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - 167 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 168 0 B0 B^0 B0 B^0 B0 B^0 43 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C, Logic Signal Connections: 176-Pin TQFP (Cont.) ispMACH 4256V/B/C ispMACH 4384V/B/C ispMACH 4512V/B/C Pin Number Bank Number GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP 169 0 B2 B^1 B2 B^1 B2 B^1 170 0 B4 B^2 B4 B^2 B4 B^2 171 0 B6 B^3 B6 B^3 B6 B^3 172 0 B8 B^4 B8 B^4 B8 B^4 173 0 B10 B^5 B10 B^5 B10 B^5 174 0 B12 B^6 B12 B^6 B12 B^6 175 0 B14 B^7 B14 B^7 B14 B^7 176 - VCC - VCC - VCC - ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C Logic Signal Connections: 256-Ball fpBGA ispMACH 4256V/B/C 128-I/O ispMACH 4256V/B/C 160-I/O ispMACH 4384V/B/C ispMACH 4512V/B/C GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP Ball Number I/O Bank - - - - - - VCC - VCC - - - GND - GND - GND - GND - C3 0 TDI - TDI - TDI - TDI - - - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - B1 0 C14 C^7 C18 C^9 C14 C^7 C14 C^7 F5 0 C12 C^6 C16 C^8 C12 C^6 C12 C^6 D3 0 C10 C^5 C14 C^7 C10 C^5 C10 C^5 C1 0 C8 C^4 C12 C^6 C8 C^4 C8 C^4 C2 0 C6 C^3 C10 C^5 C6 C^3 C6 C^3 E3 0 C4 C^2 C8 C^4 C4 C^2 C4 C^2 D2 0 C2 C^1 C6 C^3 C2 C^1 C1 C^1 F6 0 C0 C^0 C4 C^2 C0 C^0 C0 C^0 D1 0 NC - C2 C^1 F6 F^3 H0 H^0 E2 0 NC - C0 C^0 F4 F^2 H4 H^2 E4 0 NC - NC - D6 D^3 F4 F^2 G5 0 NC - NC - D4 D^2 F6 F^3 E1 0 NC - NC - NC - F8 F^4 - - - - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - - - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - F2 0 NC - NC - NC - F10 F^5 F1 0 NC - NC - D2 D^1 F12 F^6 G1 0 NC - NC - D0 D^0 F14 F^7 G6 0 NC - D18 D^9 F2 F^1 H8 H^4 G4 0 NC - D16 D^8 F0 F^0 H12 H^6 H6 0 D14 D^7 D14 D^7 E14 E^7 G14 G^7 G3 0 D12 D^6 D12 D^6 E12 E^6 G12 G^6 44 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C Logic Signal Connections: 256-Ball fpBGA (Cont.) ispMACH 4256V/B/C 128-I/O ispMACH 4256V/B/C 160-I/O Ball Number I/O Bank ispMACH 4384V/B/C ispMACH 4512V/B/C GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP H5 0 D10 D^5 D10 D^5 E10 E^5 G10 G^5 G2 0 D8 D^4 D8 D^4 E8 E^4 G8 G^4 H1 0 D6 D^3 D6 D^3 E6 E^3 G6 G^3 H2 0 D4 D^2 D4 D^2 E4 E^2 G4 G^2 H3 0 D2 D^1 E2 D^1 E2 E^1 G2 G^1 H4 0 D0 D^0 D0 D^0 E0 E^0 G0 G^0 - - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - - - - - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - J4 0 E0 E^0 E0 E^0 H0 H^0 J0 J^0 J3 0 E2 E^1 E2 E^1 H2 H^1 J2 J^1 J2 0 E4 E^2 E4 E^2 H4 H^2 J4 J^2 J1 0 E6 E^3 E6 E^3 H6 H^3 J6 J^3 K1 0 E8 E^4 E8 E^4 H8 H^4 J8 J^4 J5 0 E10 E^5 E10 E^5 H10 H^5 J10 J^5 K2 0 E12 E^6 E12 E^6 H12 H^6 J12 J^6 J6 0 E14 E^7 E14 E^7 H14 H^7 J14 J^7 K3 0 NC - E16 E^8 G0 G^0 I0 I^0 K4 0 NC - E18 E^9 G2 G^1 I4 I^2 L1 0 NC - NC - I14 I^7 K0 K^0 L2 0 NC - NC - I12 I^6 K2 K^1 M1 0 NC - NC - NC - K4 K^2 - - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - - - - - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - M2 0 NC - NC - NC - K6 K^3 N1 0 NC - NC - I10 I^5 K8 K^4 M3 0 NC - NC - I8 I^4 K10 K^5 M4 0 NC - F0 F^0 G4 G^2 I8 I^4 N2 0 NC - F2 F^1 G6 G^3 I12 I^6 K5 0 F0 F^0 F4 F^2 J0 J^0 N0 N^0 P1 0 F2 F^1 F6 F^3 J2 J^1 N2 N^1 K6 0 F4 F^2 F8 F^4 J4 J^2 N4 N^2 N3 0 F6 F^3 F10 F^5 J6 J^3 N6 N^3 L5 0 F8 F^4 F12 F^6 J8 J^4 N8 N^4 P2 0 F10 F^5 F14 F^7 J10 J^5 N10 N^5 L6 0 F12 F^6 F16 F^8 J12 J^6 N12 N^6 R1 0 F14 F^7 F18 F^9 J14 J^7 N14 N^7 - - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - P3 0 TCK - TCK - TCK - TCK - - - VCC - VCC - VCC - VCC - - - GND - GND - GND - GND - - - - - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - 45 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C Logic Signal Connections: 256-Ball fpBGA (Cont.) ispMACH 4256V/B/C 128-I/O ispMACH 4256V/B/C 160-I/O Ball Number I/O Bank ispMACH 4384V/B/C ispMACH 4512V/B/C GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP T2 0 NC - G18 G^9 I6 I^3 K12 K^6 M5 0 NC - G16 G^8 I4 I^2 K14 K^7 N4 0 G14 G^7 G14 G^7 K14 K^7 O14 O^7 T3 0 G12 G^6 G12 G^6 K12 K^6 O12 O^6 R3 0 G10 G^5 G10 G^5 K10 K^5 O10 O^5 M6 0 G8 G^4 G8 G^4 K8 K^4 O8 O^4 P4 0 G6 G^3 G6 G^3 K6 K^3 O6 O^3 L7 0 G4 G^2 G4 G^2 K4 K^2 O4 O^2 N5 0 G2 G^1 G2 G^1 K2 K^1 O2 O^1 M7 0 G0 G^0 G0 G^0 K0 K^0 O0 O^0 P5 0 NC - NC - G8 G^4 M0 M^0 R4 0 NC - NC - G10 G^5 M4 M^2 T4 0 NC - NC - NC - L0 L^0 - 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - - - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - R5 0 NC - NC - NC - L4 L^2 T5 0 NC - NC - I2 I^1 L8 L^4 R6 0 NC - NC - I0 I^0 L12 L^6 T6 0 NC - H18 H^9 G12 G^6 M8 M^4 N7 0 NC - H16 H^8 G14 G^7 M12 M^6 P7 0 H14 H^7 H14 H^7 L14 L^7 P14 P^7 R7 0 H12 H^6 H12 H^6 L12 L^6 P12 P^6 L8 0 H10 H^5 H10 H^5 L10 L^5 P10 P^5 T7 0 H8 H^4 H8 H^4 L8 L^4 P8 P^4 M8 0 H6 H^3 H6 H^3 L6 L^3 P6 P^3 N8 0 H4 H^2 H4 H^2 L4 L^2 P4 P^2 R8 0 H2 H^1 H2 H^1 L2 L^1 P2 P^1 P8 0 H0 H^0 H0 H^0 L0 L^0 P0 P^0 - - GND - GND - GND - GND - T8 0 CLK1/I - CLK1/I - CLK1/I - CLK1/I - - - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - N9 1 CLK2/I - CLK2/I - CLK2/I - CLK2/I - - - VCC - VCC - VCC - VCC - P9 1 I0 I^0 I0 I^0 M0 M^0 AX0 AX^0 R9 1 I2 I^1 I2 I^1 M2 M^1 AX2 AX^1 T9 1 I4 I^2 I4 I^2 M4 M^2 AX4 AX^2 T10 1 I6 I^3 I6 I^3 M6 M^3 AX6 AX^3 R10 1 I8 I^4 I8 I^4 M8 M^4 AX8 AX^4 M9 1 I10 I^5 I10 I^5 M10 M^5 AX10 AX^5 P10 1 I12 I^6 I12 I^6 M12 M^6 AX12 AX^6 L9 1 I14 I^7 I14 I^7 M14 M^7 AX14 AX^7 46 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C Logic Signal Connections: 256-Ball fpBGA (Cont.) ispMACH 4256V/B/C 128-I/O ispMACH 4256V/B/C 160-I/O Ball Number I/O Bank ispMACH 4384V/B/C ispMACH 4512V/B/C GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP N10 1 NC - I16 I^8 BX14 BX^7 DX0 DX^0 T11 1 NC - I18 I^9 BX12 BX^6 DX4 DX^2 R11 1 NC - NC - P0 P^0 EX0 EX^0 T12 1 NC - NC - P2 P^1 EX4 EX^2 N12 1 NC - NC - NC - EX8 EX^4 - - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - - - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - R12 1 NC - NC - NC - EX12 EX^6 T13 1 NC - J0 J^0 BX10 BX^5 DX8 DX^4 P12 1 NC - J2 J^1 BX8 BX^4 DX12 DX^6 M10 1 J0 J^0 J4 J^2 N0 N^0 BX0 BX^0 R13 1 J2 J^1 J6 J^3 N2 N^1 BX2 BX^1 L10 1 J4 J^2 J8 J^4 N4 N^2 BX4 BX^2 T14 1 J6 J^3 J10 J^5 N6 N^3 BX6 BX^3 M11 1 J8 J^4 J12 J^6 N8 N^4 BX8 BX^4 R14 1 J10 J^5 J14 J^7 N10 N^5 BX10 BX^5 P13 1 J12 J^6 J16 J^8 N12 N^6 BX12 BX^6 N13 1 J14 J^7 J18 J^9 N14 N^7 BX14 BX^7 M12 1 NC - NC - P4 P^2 FX0 FX^0 T15 1 NC - NC - P6 P^3 FX2 FX^1 - - VCC - VCC - VCC - VCC - - - GND - GND - GND - GND - - - - - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - P14 1 TMS - TMS - TMS - TMS - - - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - L12 1 NC - NC - NC - FX4 FX^2 R16 1 NC - NC - P8 P^4 FX6 FX^3 N14 1 NC - NC - P10 P^5 FX8 FX^4 P15 1 K14 K^7 K18 K^9 O14 O^7 CX14 CX^7 L11 1 K12 K^6 K16 K^8 O12 O^6 CX12 CX^6 P16 1 K10 K^5 K14 K^7 O10 O^5 CX10 CX^5 K11 1 K8 K^4 K12 K^6 O8 O^4 CX8 CX^4 M14 1 K6 K^3 K10 K^5 O6 O^3 CX6 CX^3 K12 1 K4 K^2 K8 K^4 O4 O^2 CX4 CX^2 N15 1 K2 K^1 K6 K^3 O2 O^1 CX2 CX^1 N16 1 K0 K^0 K4 K^2 O0 O^0 CX0 CX^0 M15 1 NC - K2 K^1 BX6 BX^3 HX0 HX^0 M13 1 NC - K0 K^0 BX4 BX^2 HX4 HX^2 - - - - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - - - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - M16 1 NC - NC - NC - FX10 FX^5 47 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C Logic Signal Connections: 256-Ball fpBGA (Cont.) ispMACH 4256V/B/C 128-I/O ispMACH 4256V/B/C 160-I/O Ball Number I/O Bank ispMACH 4384V/B/C ispMACH 4512V/B/C GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP L15 1 NC - NC - P12 P^6 FX12 FX^6 L16 1 NC - NC - P14 P^7 FX14 FX^7 J11 1 NC - L18 L^9 BX2 BX^1 HX8 HX^4 K15 1 NC - L16 L^8 BX0 BX^0 HX12 HX^6 J12 1 L14 L^7 L14 L^7 AX14 AX^7 GX14 GX^7 K13 1 L12 L^6 L12 L^6 AX12 AX^6 GX12 GX^6 K14 1 L10 L^5 L10 L^5 AX10 AX^5 GX10 GX^5 K16 1 L8 L^4 L8 L^4 AX8 AX^4 GX8 GX^4 J16 1 L6 L^3 L6 L^3 AX6 AX^3 GX6 GX^3 J15 1 L4 L^2 L4 L^2 AX4 AX^2 GX4 GX^2 H16 1 L2 L^1 L2 L^1 AX2 AX^1 GX2 GX^1 J13 1 L0 L^0 L0 L^0 AX0 AX^0 GX0 GX^0 - - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - - - - - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - J14 1 M0 M^0 M0 M^0 DX0 DX^0 JX0 JX^0 H15 1 M2 M^1 M2 M^1 DX2 DX^1 JX2 JX^1 H14 1 M4 M^2 M4 M^2 DX4 DX^2 JX4 JX^2 H13 1 M6 M^3 M6 M^3 DX6 DX^3 JX6 JX^3 G16 1 M8 M^4 M8 M^4 DX8 DX^4 JX8 JX^4 H12 1 M10 M^5 M10 M^5 DX10 DX^5 JX10 JX^5 G15 1 M12 M^6 M12 M^6 DX12 DX^6 JX12 JX^6 H11 1 M14 M^7 M14 M^7 DX14 DX^7 JX14 JX^7 F16 1 NC - M16 M^8 CX0 CX^0 IX0 IX^0 G13 1 NC - M18 M^9 CX2 CX^1 IX4 IX^2 G14 1 NC - NC - EX14 EX^7 KX0 KX^0 F15 1 NC - NC - EX12 EX^6 KX2 KX^1 E16 1 NC - NC - NC - KX4 KX^2 - 1 GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - - - - - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - E15 1 NC - NC - NC - KX6 KX^3 G12 1 NC - NC - EX10 EX^5 KX8 KX^4 E13 1 NC - NC - EX8 EX^4 KX10 KX^5 D16 1 NC - N0 N^0 CX4 CX^2 IX8 IX^4 E14 1 NC - N2 N^1 CX6 CX^3 IX12 IX^6 G11 1 N0 N^0 N4 N^2 FX0 FX^0 NX0 NX^0 D15 1 N2 N^1 N6 N^3 FX2 FX^1 NX2 NX^1 F11 1 N4 N^2 N8 N^4 FX4 FX^2 NX4 NX^2 C16 1 N6 N^3 N10 N^5 FX6 FX^3 NX6 NX^3 F12 1 N8 N^4 N12 N^6 FX8 FX^4 NX8 NX^4 D14 1 N10 N^5 N14 N^7 FX10 FX^5 NX10 NX^5 C15 1 N12 N^6 N16 N^8 FX12 FX^6 NX12 NX^6 48 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C Logic Signal Connections: 256-Ball fpBGA (Cont.) ispMACH 4256V/B/C 128-I/O ispMACH 4256V/B/C 160-I/O ispMACH 4384V/B/C ispMACH 4512V/B/C GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP Ball Number I/O Bank B16 1 N14 N^7 N18 N^9 FX14 FX^7 NX14 NX^7 - - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - C14 1 TDO - TDO - TDO - TDO - - - VCC - VCC - VCC - VCC - - - GND - GND - GND - GND - - - - - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - A15 1 NC - NC - EX6 EX^3 KX12 KX^6 B14 1 NC - NC - EX4 EX^2 KX14 KX^7 E12 1 O14 O^7 O18 O^9 GX14 GX^7 OX14 OX^7 A14 1 O12 O^6 O16 O^8 GX12 GX^6 OX12 OX^6 C13 1 O10 O^5 O14 O^7 GX10 GX^5 OX10 OX^5 D13 1 O8 O^4 O12 O^6 GX8 GX^4 OX8 OX^4 E11 1 O6 O^3 O10 O^5 GX6 GX^3 OX6 OX^3 B13 1 O4 O^2 O8 O^4 GX4 GX^2 OX4 OX^2 F10 1 O2 O^1 O6 O^3 GX2 GX^1 OX2 OX^1 C12 1 O0 O^0 O4 O^2 GX0 GX^0 OX0 OX^0 E10 1 NC - O2 O^1 CX8 CX^4 MX0 MX^0 A13 1 NC - O0 O^0 CX10 CX^5 MX4 MX^2 D12 1 NC - NC - NC - LX0 LX^0 - - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - GND (Bank 1) - - - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - VCCO (Bank 1) - B12 1 NC - NC - NC - LX4 LX^2 A12 1 NC - NC - EX2 EX^1 LX8 LX^4 B11 1 NC - NC - EX0 EX^0 LX12 LX^6 A11 1 NC - P18 P^9 CX12 CX^6 MX8 MX^4 D10 1 NC - P16 P^8 CX14 CX^7 MX12 MX^6 C10 1 P14 P^7 P14 P^7 HX14 HX^7 PX14 PX^7 B10 1 P12 P^6 P12 P6 HX12 HX^6 PX12 PX^6 A10 1 P10 P^5 P10 P^5 HX10 HX^5 PX10 PX^5 A9 1 P8 P^4 P8 P^4 HX8 HX^4 PX8 PX^4 F9 1 P6 P^3 P6 P^3 HX6 HX^3 PX6 PX^3 B9 1 P4 P^2 P4 P^2 HX4 HX^2 PX4 PX^2 E9 1 P2/GOE1 P^1 P2/GOE1 P^1 HX2/GOE1 HX^1 PX2/GOE1 PX^1 C9 1 P0 P^0 P0 P^0 HX0 HX^0 PX0 PX^0 - - GND - GND GND - GND - D9 0 CLK3/I - CLK3/I - CLK3/I - CLK3/I - - - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - B8 0 CLK0/I - CLK0/I - CLK0/I - CLK0/I - - - VCC - VCC - VCC - VCC - D8 0 A0 A^0 A0 A^0 A0 A^0 A0 A^0 C8 0 A2/GOE0 A^1 A2/GOE0 A^1 A2/GOE0 A^1 A2/GOE0 A^1 49 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4256V/B/C, 4384V/B/C, 4512V/B/C Logic Signal Connections: 256-Ball fpBGA (Cont.) ispMACH 4256V/B/C 128-I/O ispMACH 4256V/B/C 160-I/O Ball Number I/O Bank ispMACH 4384V/B/C ispMACH 4512V/B/C GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP GLB/MC/Pad ORP A8 0 A4 A^2 A4 A^2 A4 A^2 A4 A^2 A7 0 A6 A^3 A6 A^3 A6 A^3 A6 A^3 B7 0 A8 A^4 A8 A^4 A8 A^4 A8 A^4 E8 0 A10 A^5 A10 A^5 A10 A^5 A10 A^5 D7 0 A12 A^6 A12 A^6 A12 A^6 A12 A^6 F8 0 A14 A^7 A14 A^7 A14 A^7 A14 A^7 C7 0 NC - A16 A^8 F14 F^7 D0 D^0 A6 0 NC - A18 A^9 F12 F^6 D4 D^2 B6 0 NC - NC - D14 D^7 E0 E^0 A5 0 NC - NC - D12 D^6 E4 E^2 B5 0 NC - NC - NC - E8 E^4 - - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - VCCO (Bank 0) - - 0 GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - GND (Bank 0) - D5 0 NC - NC - NC - E12 E^6 A4 0 NC - B0 B^0 F10 F^5 D8 D^4 E7 0 NC - B2 B^1 F8 F^4 D12 D^6 A3 0 B0 B^0 B4 B^2 B0 B^0 B0 B^0 F7 0 B2 B^1 B6 B^3 B2 B^1 B2 B^1 B4 0 B4 B^2 B8 B^4 B4 B^2 B4 B^2 C5 0 B6 B^3 B10 B^5 B6 B^3 B6 B^3 A2 0 B8 B^4 B12 B^6 B8 B^4 B8 B^4 E6 0 B10 B^5 B14 B^7 B10 B^5 B10 B^5 B3 0 B12 B^6 B16 B^8 B12 B^6 B12 B^6 C4 0 B14 B^7 B18 B^9 B14 B^7 B14 B^7 D4 0 NC - NC - D10 D^5 F0 F^0 E5 0 NC - NC - D8 D^4 F2 F^1 - - VCC - VCC - VCC - VCC - - - - - - - GND - GND - - - - - - - GND (Bank 0) - GND (Bank 0) - 50 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet Part Number Description LC XXXX X – XX X XXX X X XX Production Status Blank = Final production ES = Engineering Samples Device Family Device Number 4032 = 32 Macrocells 4064 = 64 Macrocells 4128 = 128 Macrocells 4256 = 256 Macrocells 4384 = 384 Macrocells 4512 = 512 Macrocells Grade C = Commercial I = Industrial I/O Designator A = 128 I/Os B = 160 I/Os Supply Voltage V = 3.3V B = 2.5V C = 1.8V Pin/Ball Count 44 (1.0mm thickness) 48 (1.0mm thickness) 100 128 176 256 Speed 25 = 2.5ns 27 = 2.7ns 3 = 3.0ns 35 = 3.5ns 5 = 5.0ns 75 = 7.5ns 10 = 10.0ns Package T = TQFP F = fpBGA 0212/ispm4K Ordering Information ispMACH 4000C Commercial Devices Device LC4032C LC4064C LC4128C Macrocells Voltage tPD Package Pin/Ball Count I/O LC4032C-25T48C Part Number 32 1.8 2.5 TQFP 48 32 Grade C LC4032C-5T48C 32 1.8 5 TQFP 48 32 C LC4032C-75T48C 32 1.8 7.5 TQFP 48 32 C LC4032C-25T44C 32 1.8 2.5 TQFP 44 30 C LC4032C-5T44C 32 1.8 5 TQFP 44 30 C LC4032C-75T44C 32 1.8 7.5 TQFP 44 30 C LC4064C-25T100C 64 1.8 2.5 TQFP 100 64 C LC4064C-5T100C 64 1.8 5 TQFP 100 64 C LC4064C-75T100C 64 1.8 7.5 TQFP 100 64 C LC4128C-27T128C 128 1.8 2.7 TQFP 128 92 C LC4128C-5T128C 128 1.8 5 TQFP 128 92 C LC4128C-75T128C 128 1.8 7.5 TQFP 128 92 C LC4128C-27T100C 128 1.8 2.7 TQFP 100 64 C LC4128C-5T100C 128 1.8 5 TQFP 100 64 C LC4128C-75T100C 128 1.8 7.5 TQFP 100 64 C 51 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000C Commercial Devices (Cont.) Device LC4256C LC4384C LC4512C Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4256C-3F256AC Part Number 256 1.8 3 fpBGA 256 128 C LC4256C-5F256AC 256 1.8 5 fpBGA 256 128 C LC4256C-75F256AC 256 1.8 7.5 fpBGA 256 128 C LC4256C-3F256BC 256 1.8 3 fpBGA 256 160 C LC4256C-5F256BC 256 1.8 5 fpBGA 256 160 C LC4256C-75F256BC 256 1.8 7.5 fpBGA 256 160 C LC4256C-3T176C 256 1.8 3 TQFP 176 128 C LC4256C-5T176C 256 1.8 5 TQFP 176 128 C LC4256C-75T176C 256 1.8 7.5 TQFP 176 128 C LC4256C-3T100C 256 1.8 3 TQFP 100 64 C LC4256C-5T100C 256 1.8 5 TQFP 100 64 C LC4256C-75T100C 256 1.8 7.5 TQFP 100 64 C LC4384C-35F256C 384 1.8 3.5 fpBGA 256 192 C LC4384C-5F256C 384 1.8 5 fpBGA 256 192 C LC4384C-75F256C 384 1.8 7.5 fpBGA 256 192 C LC4384C-35T176C 384 1.8 3.5 TQFP 176 128 C LC4384C-5T176C 384 1.8 5 TQFP 176 128 C LC4384C-75T176C 384 1.8 7.5 TQFP 176 128 C LC4512C-35F256C 512 1.8 3.5 fpBGA 256 208 C LC4512C-5F256C 512 1.8 5 fpBGA 256 208 C LC4512C-75F256C 512 1.8 7.5 fpBGA 256 208 C LC4512C-35T176C 512 1.8 3.5 TQFP 176 128 C LC4512C-5T176C 512 1.8 5 TQFP 176 128 C LC4512C-75T176C 512 1.8 7.5 TQFP 176 128 C Pin/Ball Count I/O Grade ispMACH 4000B Commercial Devices Device LC4032B LC4064B LC4128B Part Number Macrocells Voltage tPD Package LC4032B-25T48C 32 2.5 2.5 TQFP 48 32 C LC4032B-5T48C 32 2.5 5 TQFP 48 32 C LC4032B-75T48C 32 2.5 7.5 TQFP 48 32 C LC4032B-25T44C 32 2.5 2.5 TQFP 44 30 C LC4032B-5T44C 32 2.5 5 TQFP 44 30 C LC4032B-75T44C 32 2.5 7.5 TQFP 44 30 C LC4064B-25T100C 64 2.5 2.5 TQFP 100 64 C LC4064B-5T100C 64 2.5 5 TQFP 100 64 C LC4064B-75T100C 64 2.5 7.5 TQFP 100 64 C LC4128B-27T128C 128 2.5 2.7 TQFP 128 92 C LC4128B-5T128C 128 2.5 5 TQFP 128 92 C LC4128B-75T128C 128 2.5 7.5 TQFP 128 92 C LC4128B-27T100C 128 2.5 2.7 TQFP 100 64 C LC4128B-5T100C 128 2.5 5 TQFP 100 64 C LC4128B-75T100C 128 2.5 7.5 TQFP 100 64 C 52 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000B Commercial Devices (Cont.) Device LC4256B LC4384B LC4512B Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4256B-3F256AC Part Number 256 2.5 3 fpBGA 256 128 C LC4256B-5F256AC 256 2.5 5 fpBGA 256 128 C LC4256B-75F256AC 256 2.5 7.5 fpBGA 256 128 C LC4256B-3F256BC 256 2.5 3 fpBGA 256 160 C LC4256B-5F256BC 256 2.5 5 fpBGA 256 160 C LC4256B-75F256BC 256 2.5 7.5 fpBGA 256 160 C LC4256B-3T176C 256 2.5 3 TQFP 176 128 C LC4256B-5T176C 256 2.5 5 TQFP 176 128 C LC4256B-75T176C 256 2.5 7.5 TQFP 176 128 C LC4256B-3T100C 256 2.5 3 TQFP 100 64 C LC4256B-5T100C 256 2.5 5 TQFP 100 64 C LC4256B-75T100C 256 2.5 7.5 TQFP 100 64 C LC4384B-35F256C 384 2.5 3.5 fpBGA 256 192 C LC4384B-5F256C 384 2.5 5 fpBGA 256 192 C LC4384B-75F256C 384 2.5 7.5 fpBGA 256 192 C LC4384B-35T176C 384 2.5 3.5 TQFP 176 128 C LC4384B-5T176C 384 2.5 5 TQFP 176 128 C LC4384B-75T176C 384 2.5 7.5 TQFP 176 128 C LC4512B-35F256C 512 2.5 3.5 fpBGA 256 208 C LC4512B-5F256C 512 2.5 5 fpBGA 256 208 C LC4512B-75F256C 512 2.5 7.5 fpBGA 256 208 C LC4512B-35T176C 512 2.5 3.5 TQFP 176 128 C LC4512B-5T176C 512 2.5 5 TQFP 176 128 C LC4512B-75T176C 512 2.5 7.5 TQFP 176 128 C Pin/Ball Count I/O Grade ispMACH 4000V Commercial Devices Device LC4032V LC4064V LC4128V Part Number Macrocells Voltage tPD Package LC4032V-25T48C 32 3.3 2.5 TQFP 48 32 C LC4032V-5T48C 32 3.3 5 TQFP 48 32 C LC4032V-75T48C 32 3.3 7.5 TQFP 48 32 C LC4032V-25T44C 32 3.3 2.5 TQFP 44 30 C LC4032V-5T44C 32 3.3 5 TQFP 44 30 C LC4032V-75T44C 32 3.3 7.5 TQFP 44 30 C LC4064V-25T100C 64 3.3 2.5 TQFP 100 64 C LC4064V-5T100C 64 3.3 5 TQFP 100 64 C LC4064V-75T100C 64 3.3 7.5 TQFP 100 64 C LC4128V-27T128C 128 3.3 2.7 TQFP 128 92 C LC4128V-5T128C 128 3.3 5 TQFP 128 92 C LC4128V-75T128C 128 3.3 7.5 TQFP 128 92 C LC4128V-27T100C 128 3.3 2.7 TQFP 100 64 C LC4128V-5T100C 128 3.3 5 TQFP 100 64 C LC4128V-75T100C 128 3.3 7.5 TQFP 100 64 C 53 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V Commercial Devices (Cont.) Device LC4256V LC4384V LC4512V Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4256V-3F256AC Part Number 256 3.3 3 fpBGA 256 128 C LC4256V-5F256AC 256 3.3 5 fpBGA 256 128 C LC4256V-75F256AC 256 3.3 7.5 fpBGA 256 128 C LC4256V-3F256BC 256 3.3 3 fpBGA 256 160 C LC4256V-5F256BC 256 3.3 5 fpBGA 256 160 C LC4256V-75F256BC 256 3.3 7.5 fpBGA 256 160 C LC4256V-3T176C 256 3.3 3 TQFP 176 128 C LC4256V-5T176C 256 3.3 5 TQFP 176 128 C LC4256V-75T176C 256 3.3 7.5 TQFP 176 128 C LC4256V-3T100C 256 3.3 3 TQFP 100 64 C LC4256V-5T100C 256 3.3 5 TQFP 100 64 C LC4256V-75T100C 256 3.3 7.5 TQFP 100 64 C LC4384V-35F256C 384 3.3 3.5 fpBGA 256 192 C LC4384V-5F256C 384 3.3 5 fpBGA 256 192 C LC4384V-75F256C 384 3.3 7.5 fpBGA 256 192 C LC4384V-35T176C 384 3.3 3.5 TQFP 176 128 C LC4384V-5T176C 384 3.3 5 TQFP 176 128 C LC4384V-75T176C 384 3.3 7.5 TQFP 176 128 C LC4512V-35F256C 512 3.3 3.5 fpBGA 256 208 C LC4512V-5F256C 512 3.3 5 fpBGA 256 208 C LC4512V-75F256C 512 3.3 7.5 fpBGA 256 208 C LC4512V-35T176C 512 3.3 3.5 TQFP 176 128 C LC4512V-5T176C 512 3.3 5 TQFP 176 128 C LC4512V-75T176C 512 3.3 7.5 TQFP 176 128 C Note: The ispMACH 4000V/B/C family is dual-marked with both commercial and industrial grades. The commercial speed grade is one speed grade faster (i.e. LC4128C-5T100C) than the industrial speed grade (i.e. LC4128C-75T100I). ispMACH 4000C Industrial Devices Family LC4032C LC4064C Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4032C-5T48I Part Number 32 1.8 5 TQFP 48 32 I LC4032C-75T48I 32 1.8 7.5 TQFP 48 32 I LC4032C-10T48I 32 1.8 10 TQFP 48 32 I LC4032C-5T44I 32 1.8 5 TQFP 44 30 I LC4032C-75T44I 32 1.8 7.5 TQFP 44 30 I LC4032C-10T44I 32 1.8 10 TQFP 44 30 I LC4064C-5T100I 64 1.8 5 TQFP 100 64 I LC4064C-75T100I 64 1.8 7.5 TQFP 100 64 I LC4064C-10T100I 64 1.8 10 TQFP 100 64 I 54 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000C Industrial Devices (Cont.) Family LC4128C LC4256C LC4384C LC4512C Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4128C-5T128I Part Number 128 1.8 5 TQFP 128 92 I LC4128C-75T128I 128 1.8 7.5 TQFP 128 92 I LC4128C-10T128I 128 1.8 10 TQFP 128 92 I LC4128C-5T100I 128 1.8 5 TQFP 100 64 I LC4128C-75T100I 128 1.8 7.5 TQFP 100 64 I LC4128C-10T100I 128 1.8 10 TQFP 100 64 I LC4256C-5F256AI 256 1.8 5 fpBGA 256 128 I LC4256C-75F256AI 256 1.8 7.5 fpBGA 256 128 I LC4256C-10F256AI 256 1.8 10 fpBGA 256 128 I LC4256C-5F256BI 256 1.8 5 fpBGA 256 160 I LC4256C-75F256BI 256 1.8 7.5 fpBGA 256 160 I LC4256C-10F256BI 256 1.8 10 fpBGA 256 160 I LC4256C-5T176I 256 1.8 5 TQFP 176 128 I LC4256C-75T176I 256 1.8 7.5 TQFP 176 128 I LC4256C-10T176I 256 1.8 10 TQFP 176 128 I LC4256C-5T100I 256 1.8 5 TQFP 100 64 I LC4256C-75T100I 256 1.8 7.5 TQFP 100 64 I LC4256C-10T100I 256 1.8 10 TQFP 100 64 I LC4384C-5F256I 384 1.8 5 fpBGA 256 192 I LC4384C-75F256I 384 1.8 7.5 fpBGA 256 192 I LC4384C-10F256I 384 1.8 10 fpBGA 256 192 I LC4384C-5T176I 384 1.8 5 TQFP 176 128 I LC4384C-75T176I 384 1.8 7.5 TQFP 176 128 I LC4384C-10T176I 384 1.8 10 TQFP 176 128 I LC4512C-5F256I 512 1.8 5 fpBGA 256 208 I LC4512C-75F256I 512 1.8 7.5 fpBGA 256 208 I LC4512C-10F256I 512 1.8 10 fpBGA 256 208 I LC4512C-5T176I 512 1.8 5 TQFP 176 128 I LC4512C-75T176I 512 1.8 7.5 TQFP 176 128 I LC4512C-10T176I 512 1.8 10 TQFP 176 128 I ispMACH 4000B Industrial Devices Family LC4032B LC4064B Part Number Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4032B-5T48I 32 LC4032B-75T48I 32 2.5 5 TQFP 48 32 I 2.5 7.5 TQFP 48 32 I LC4032B-10T48I 32 2.5 10 TQFP 48 32 I LC4032B-5T44I 32 2.5 5 TQFP 44 30 I LC4032B-75T44I 32 2.5 7.5 TQFP 44 30 I LC4032B-10T44I 32 2.5 10 TQFP 44 30 I LC4064B-5T100I 64 2.5 5 TQFP 100 64 I LC4064B-75T100I 64 2.5 7.5 TQFP 100 64 I LC4064B-10T100I 64 2.5 10 TQFP 100 64 I 55 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000B Industrial Devices (Cont.) Family LC4128B LC4256B LC4384B LC4512B Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4128B-5T128I Part Number 128 2.5 5 TQFP 128 92 I LC4128B-75T128I 128 2.5 7.5 TQFP 128 92 I LC4128B-10T128I 128 2.5 10 TQFP 128 92 I LC4128B-5T100I 128 2.5 5 TQFP 100 64 I LC4128B-75T100I 128 2.5 7.5 TQFP 100 64 I LC4128B-10T100I 128 2.5 10 TQFP 100 64 I LC4256B-5F256AI 256 2.5 5 fpBGA 256 128 I LC4256B-75F256AI 256 2.5 7.5 fpBGA 256 128 I LC4256B-10F256AI 256 2.5 10 fpBGA 256 128 I LC4256B-5F256BI 256 2.5 5 fpBGA 256 160 I LC4256B-75F256BI 256 2.5 7.5 fpBGA 256 160 I LC4256B-10F256BI 256 2.5 10 fpBGA 256 160 I LC4256B-5T176I 256 2.5 5 TQFP 176 128 I LC4256B-75T176I 256 2.5 7.5 TQFP 176 128 I LC4256B-10T176I 256 2.5 10 TQFP 176 128 I LC4256B-5T100I 256 2.5 5 TQFP 100 64 I LC4256B-75T100I 256 2.5 7.5 TQFP 100 64 I LC4256B-10T100I 256 2.5 10 TQFP 100 64 I LC4384B-5F256I 384 2.5 5 fpBGA 256 192 I LC4384B-75F256I 384 2.5 7.5 fpBGA 256 192 I LC4384B-10F256I 384 2.5 10 fpBGA 256 192 I LC4384B-5T176I 384 2.5 5 TQFP 176 128 I LC4384B-75T176I 384 2.5 7.5 TQFP 176 128 I LC4384B-10T176I 384 2.5 10 TQFP 176 128 I LC4512B-5F256I 512 2.5 5 fpBGA 256 208 I LC4512B-75F256I 512 2.5 7.5 fpBGA 256 208 I LC4512B-10F256I 512 2.5 10 fpBGA 256 208 I LC4512B-5T176I 512 2.5 5 TQFP 176 128 I LC4512B-75T176I 512 2.5 7.5 TQFP 176 128 I LC4512B-10T176I 512 2.5 10 TQFP 176 128 I ispMACH 4000V Industrial Devices Family LC4032V LC4064V Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4032V-5T48I Part Number 32 3.3 5 TQFP 48 32 I LC4032V-75T48I 32 3.3 7.5 TQFP 48 32 I LC4032V-10T48I 32 3.3 10 TQFP 48 32 I LC4032V-5T44I 32 3.3 5 TQFP 44 30 I LC4032V-75T44I 32 3.3 7.5 TQFP 44 30 I LC4032V-10T44I 32 3.3 10 TQFP 44 30 I LC4064V-5T100I 64 3.3 5 TQFP 100 64 I LC4064V-75T100I 64 3.3 7.5 TQFP 100 64 I LC4064V-10T100I 64 3.3 10 TQFP 100 64 I 56 Lattice Semiconductor ispMACH 4000V/B/C Family Data Sheet ispMACH 4000V Industrial Devices (Cont.) Family LC4128V LC4256V LC4384V LC4512V Macrocells Voltage tPD Package Pin/Ball Count I/O Grade LC4128V-5T128I Part Number 128 3.3 5 TQFP 128 92 I LC4128V-75T128I 128 3.3 7.5 TQFP 128 92 I LC4128V-10T128I 128 3.3 10 TQFP 128 92 I LC4128V-5T100I 128 3.3 5 TQFP 100 64 I LC4128V-75T100I 128 3.3 7.5 TQFP 100 64 I LC4128V-10T100I 128 3.3 10 TQFP 100 64 I LC4256V-5F256AI 256 3.3 5 fpBGA 256 128 I LC4256V-75F256AI 256 3.3 7.5 fpBGA 256 128 I LC4256V-10F256AI 256 3.3 10 fpBGA 256 128 I LC4256V-5F256BI 256 3.3 5 fpBGA 256 160 I LC4256V-75F256BI 256 3.3 7.5 fpBGA 256 160 I LC4256V-10F256BI 256 3.3 10 fpBGA 256 160 I LC4256V-5T176I 256 3.3 5 TQFP 176 128 I LC4256V-75T176I 256 3.3 7.5 TQFP 176 128 I LC4256V-10T176I 256 3.3 10 TQFP 176 128 I LC4256V-5T100I 256 3.3 5 TQFP 100 64 I LC4256V-75T100I 256 3.3 7.5 TQFP 100 64 I LC4256V-10T100I 256 3.3 10 TQFP 100 64 I LC4384V-5F256I 384 3.3 5 fpBGA 256 192 I LC4384V-75F256I 384 3.3 7.5 fpBGA 256 192 I LC4384V-10F256I 384 3.3 10 fpBGA 256 192 I LC4384V-5T176I 384 3.3 5 TQFP 176 128 I LC4384V-75T176I 384 3.3 7.5 TQFP 176 128 I LC4384V-10T176I 384 3.3 10 TQFP 176 128 I LC4512V-5F256I 512 3.3 5 fpBGA 256 208 I LC4512V-75F256I 512 3.3 7.5 fpBGA 256 208 I LC4512V-10F256I 512 3.3 10 fpBGA 256 208 I LC4512V-5T176I 512 3.3 5 TQFP 176 128 I LC4512V-75T176I 512 3.3 7.5 TQFP 176 128 I LC4512V-10T176I 512 3.3 10 TQFP 176 128 I Note: The ispMACH 4000V/B/C family is dual-marked with both commercial and industrial grades. The commercial speed grade is one speed grade faster (i.e. LC4128C-5T100C) than the industrial speed grade (i.e. LC4128C-75T100I). For Further Information In addition to this data sheet, the following technical notes may be helpful when designing with the ispMACH 4000V/B/C family: • ispMACH 4000 Timing Model Design and Usage Guidelines (TN1004) • ispMACH 4000V/B/C Power Consumption (TN1005) 57