ISSI ISSI® IS62C256 IS62C256 ® 32K x 8 LOW POWER CMOS STATIC RAM FEATURES DESCRIPTION The ISSI IS62C256 is a low power, 32,768 word by 8-bit CMOS static RAM. It is fabricated using ISSI's high- • Access time: 45, 70, 100 ns • Low active power: 200 mW (typical) • Low standby power — 250 µW (typical) CMOS standby — 28 mW (typical) TTL standby • Fully static operation: no clock or refresh required • TTL compatible inputs and outputs • Single 5V power supply performance, low power CMOS technology. When CE is HIGH (deselected), the device assumes a standby mode at which the power dissipation can be reduced down to 250 µW (typical) at CMOS input levels. Easy memory expansion is provided by using an active LOW Chip Enable (CE) input and an active LOW Output Enable (OE) input. The active LOW Write Enable (WE) controls both writing and reading of the memory. The IS62C256 is pin compatible with other 32K X 8 SRAMs in 600-mil PDIP, 450-mil plastic SOP, or TSOP package. FUNCTIONAL BLOCK DIAGRAM A0-A14 DECODER 256 X 1024 MEMORY ARRAY I/O DATA CIRCUIT COLUMN I/O VCC GND I/O0-I/O7 CE OE CONTROL CIRCUIT WE ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which may appear in this publication. © Copyright 1995, Integrated Silicon Solution, Inc. Integrated Silicon Solution, Inc. Rev. D 0895 SR81995C256 2-1 ISSI IS62C256 PIN CONFIGURATION PIN CONFIGURATION 28-Pin DIP and SOP 28-Pin TSOP A14 1 28 VCC A12 2 27 WE A7 3 26 A13 A6 4 25 A8 A5 5 24 A9 A4 6 23 A11 A3 7 22 OE A2 8 21 A10 A1 9 20 CE A0 10 19 I/O7 I/O0 11 18 I/O6 I/O1 12 17 I/O5 I/O2 13 16 I/O4 GND 14 15 I/O3 PIN DESCRIPTIONS A0-A14 CE OE WE OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3 Mode Chip Enable Input Not Selected (Power-down) Output Disabled Read Write Write Enable Input I/O0-I/O7 Input/Output Vcc Power GND Ground A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 TRUTH TABLE Address Inputs Output Enable Input 21 20 19 18 17 16 15 14 13 12 11 10 9 8 22 23 24 25 26 27 28 1 2 3 4 5 6 7 ® WE CE OE I/O Operation Vcc Current X H X High-Z ISB1, ISB2 H H L L L L H L X High-Z DOUT DIN ICC1, ICC2 ICC1, ICC2 ICC1, ICC2 ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM TBIAS TSTG PT IOUT Parameter Terminal Voltage with Respect to GND Temperature Under Bias Storage Temperature Power Dissipation DC Output Current (LOW) Value –0.5 to +7.0 –55 to +125 –65 to +150 0.5 20 Unit V °C °C W mA Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2-2 Integrated Silicon Solution, Inc. Rev. D 0895 SR81995C256 ISSI IS62C256 ® OPERATING RANGE Range Commercial Industrial Ambient Temperature 0°C to +70°C –40°C to +85°C VCC 5V ± 10% 5V ± 10% DC ELECTRICAL CHARACTERISTICS Symbol VOH Parameter Output HIGH Voltage Test Conditions VCC = Min., IOH = –1.0 mA Min. 2.4 Max. — Unit V VOL VIH VIL ILI Output LOW Voltage Input HIGH Voltage Input LOW Voltage(1) Input Leakage VCC = Min., IOL = 2.1 mA Output Leakage 0.4 VCC + 0.5 0.8 2 10 2 10 V V V µA ILO — 2.2 –0.3 –2 –10 –2 –10 GND ≤ VIN ≤ VCC Com. Ind. Com. Ind. GND ≤ VOUT ≤ VCC, Outputs Disabled µA Notes: 1. VIL = –3.0V for pulse width less than 10 ns. POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol ICC1 ICC2 ISB1 ISB2 Parameter Vcc Operating Supply Current Vcc Dynamic Operating Supply Current TTL Standby Current (TTL Inputs) CMOS Standby Current (CMOS Inputs) Test Conditions VCC = Max., CE = VIL IOUT = 0 mA, f = 0 VCC = Max., CE = VIL IOUT = 0 mA, f = fMAX VCC = Max., VIN = VIH or VIL CE ≥ VIH, f = 0 VCC = Max., CE ≥ VCC – 0.2V, VIN ≥ VCC – 0.2V, or VIN ≤ 0.2V, f = 0 Com. Ind. Com. Ind. Com. Ind. Com. Ind. -45 ns Min. Max. — 60 — 70 — 70 — 80 — 5 — 10 — — 0.5 1.0 -70 ns Min. Max. — 60 — 70 — 65 — 75 — 5 — 10 — — 0.5 1.0 -100 ns Min. Max. — 60 — 70 — 65 — 75 — 5 — 10 — — 0.5 1.0 Unit mA mA mA mA Notes: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. CAPACITANCE(1,2) Symbol CIN COUT Parameter Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Max. 8 10 Unit pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz, Vcc = 5.0V. Integrated Silicon Solution, Inc. Rev. D 0895 SR81995C256 2-3 ISSI IS62C256 ® DATA RETENTION CHARACTERISTICS Symbol VDR IDR1 IDR2 Parameter VCC for retention of data Data retention current Data retention current Test Conditions Min. 2.0 — — VDR = 3.0V, TA = 0°C to +25°C VDR = 3.0V, TA = 0°C to +70°C Max. — 200 200 Units V µA µA READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) Symbol -45 ns Min. Max. Parameter -70 ns Min. Max. -100 ns Min. Max. Unit tRC Read Cycle Time 45 — 70 — 100 — ns tAA Address Access Time — 45 — 70 — 100 ns tOHA Output Hold Time 2 — 2 — 2 — ns — 45 — 70 — 100 ns — 25 — 35 — 50 ns 0 — 0 — 0 — ns 0 20 0 25 0 25 ns 3 — 3 — 3 — ns 0 20 0 25 0 25 ns 0 — 0 — 0 — ns — 30 — 50 — 50 ns tACE tDOE tLZOE (2) tHZOE (2) tLZCE(2) tHZCE(2) tPU (3) tPD (3) CE Access Time OE Access Time OE to Low-Z Output OE to High-Z Output CE to Low-Z Output CE to High-Z Output CE to Power-Up CE to Power-Down Notes: 1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V and output loading specified in Figure 1a. 2. Tested with the load in Figure 1b. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. Not 100% tested. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Levels Output Load Unit 0V to 3.0V 3 ns 1.5V See Figures 1a and 1b AC TEST LOADS 480 Ω 480 Ω 5V 5V OUTPUT OUTPUT 100 pF Including jig and scope Figure 1a. 2-4 255 Ω 5 pF Including jig and scope 255 Ω Figure 1b. Integrated Silicon Solution, Inc. Rev. D 0895 SR81995C256 ISSI IS62C256 ® AC WAVEFORMS READ CYCLE NO. 1(1,2) tRC ADDRESS tAA tOHA tOHA DOUT DATA VALID READ CYCLE NO. 2(1,3) tRC ADDRESS tAA tOHA OE tDOE tLZOE CE tACE tLZCE DOUT HIGH-Z tHZCE DATA VALID tPU SUPPLY CURRENT tHZOE tPD 50% ICC 50% ISB Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE = VIL. 3. Address is valid prior to or coincident with CE LOW transitions. Integrated Silicon Solution, Inc. Rev. D 0895 SR81995C256 2-5 ISSI IS62C256 ® WRITE CYCLE SWITCHING CHARACTERISTICS(1,3) (Over Operating Range) Symbol -45 ns Min. Max. Parameter -70ns Min. Max. -100 ns Min. Max. Unit tWC Write Cycle Time 45 — 70 — 100 — ns tSCE CE to Write End 35 — 60 — 80 — ns tAW Address Setup Time to Write End 25 — 60 — 80 — ns tHA Address Hold from Write End 0 — 0 — 0 — ns Address Setup Time 0 — 0 — 0 — ns tPWE WE Pulse Width 25 — 55 — 60 — ns tSD Data Setup to Write End 20 — 30 — 35 — ns tHD Data Hold from Write End 0 — 0 — 0 — ns tSA (4) Notes: 1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V and output loading specified in Figure 1a. 2. Tested with the load in Figure 1b. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. 4. Tested with OE HIGH. AC WAVEFORMS WRITE CYCLE NO. 1 (WE Controlled)(1,2) tWC ADDRESS tHA tSCE CE tAW tPWE WE tSA DOUT tHZWE DATA UNDEFINED tLZWE HIGH-Z tSD DIN 2-6 tHD DATA-IN VALID Integrated Silicon Solution, Inc. Rev. D 0895 SR81995C256 ISSI IS62C256 ® WRITE CYCLE NO. 2 (CE Controlled)(1,2) tWC ADDRESS tSA tHA tSCE CE tAW tPWE WE tHZWE DOUT DATA UNDEFINED tLZWE HIGH-Z tSD DIN tHD DATA-IN VALID Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. 2. I/O will assume the High-Z state if OE ≥ VIH. ORDERING INFORMATION Commerical Range: 0°C to +70°C ORDERING INFORMATION Industrial Range: –40°C to +85°C Speed (ns) Order Part No. Package Speed (ns) Order Part No. Package 45 45 45 IS62C256-45W IS62C256-45T IS62C256-45U 600-mil Plastic DIP TSOP 450-mil Plastic SOP 45 45 45 IS62C256-45WI IS62C256-45TI IS62C256-45UI 600-mil Plastic DIP TSOP 450-mil Plastic SOP 70 70 70 IS62C256-70W IS62C256-70T IS62C256-70U 600-mil Plastic DIP TSOP 450-mil Plastic SOP 70 70 70 IS62C256-70WI IS62C256-70TI IS62C256-70UI 600-mil Plastic DIP TSOP 450-mil Plastic SOP 100 100 100 IS62C256-100W IS62C256-100T IS62C256-100U 600-mil Plastic DIP TSOP 450-mil Plastic SOP 100 100 100 IS62C256-100WI 600-mil Plastic DIP IS62C256-100TI TSOP IS62C256-100UI 450-mil Plastic SOP ISSI ® Integrated Silicon Solution, Inc. 2231 Lawson Lane Santa Clara, CA 95054 800-379-4774 Fax: 408-588-0806 E-mail: [email protected] Web: www.issiusa.com Integrated Silicon Solution, Inc. Rev. D 0895 SR81995C256 2-7