SI-3025ZF Data Sheet 27468.27* ar ors e n t Li ula g e R High-Current, Low-Dropout, 2.5 V Regulator Designed to meet the high-current requirements in industrial and consumer applications; embedded core, memory, or logic supplies; TVs, VCRs, and office equipment, the SI-3025ZF voltage regulator offers the reduced dropout voltage and low quiescent current essential for improved efficiency. This device delivers a regulated output at up to 3 A. Integrated thermal and overcurrent protection enhance overall system reliability. Devices with an adjustable 1.2 ~ 5 V output or a 3.3 V fixed output are also available. Quiescent current does not increase significantly as the dropout voltage is approached, an ideal feature in standby/resume power systems where data integrity is crucial. Regulator accuracy and excellent temperature characteristics are provided by a bandgap reference. An LS-TTL/CMOS-compatible input gives the designer complete control over power up, standby, or power down. A pnp pass element provides a dropout voltage of less than 700 mV at 3 A of load current. Low output voltages eliminate the need for expensive PWM buck converters. The low dropout voltage permits more efficient regulation before output regulation is lost. This device is supplied in a fully molded TO-220-style 5-lead flange-mounted , high power, isolated plastic package. A similar device in a lower-power surface-mount plastic package is the SI-3025ZD. ABSOLUTE MAXIMUM RATINGS Input Voltage, VI . . . . . . . . . . . . . 10 V Output Current, IO . . . . . . . . . . . . . 3 A* Enable Input Voltage, VE . . . . . . . . 6V Junction Temperature, TJ . . . . +125°C Storage Temperature Range, TS . . . . . . . . . . . . -40°C to +125°C FEATURES ■ 3 A Output Current at 2.5 V ■ 0.7 V Maximum Dropout Voltage at IO = 3 A ■ 1 µA Maximum Standby Current ■ Remote Voltage Sensing ■ Foldback Current Limiting ■ Thermal Protection APPLICATIONS ■ TVs, VCRs, Electronic Games ■ Embedded Core, Memory, or Logic Supplies ■ Printers and Other Office Equipment ■ Industrial Machinery ■ Secondary-Side Stabilization of Multi-Output SMPS * Output current rating is limited by input voltage, duty cycle, and ambient temperature. Under any set of conditions, do not exceed a junction temperature of +125°C. Always order by complete part number, e.g., SI-3025ZF . Sanken Power Devices from Allegro MicroSystems ar ors e n t Li ula g Re SI-3025ZF High-Current, Low-Dropout, 2.5 V Regulator FUNCTIONAL BLOCK DIAGRAM Allowable Package Power Dissipation Recommended Operating Conditions DC Input Voltage DC Output Current Operating Junction Temp. Min — 0 -20 Max 6 3 +100 Units V A °C For the availability of parts meeting -40°C requirements, contact Allegro’s Sales Representative. This data sheet is based on Sanken data sheet SSJ-02578 2 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 Copyright © 2004, 2005 Allegro MicroSystems, Inc. ar ors e n t Li ula g e R SI-3025ZF High-Current, Low-Dropout, 2.5 V Regulator ELECTRICAL CHARACTERISTICS at TA = +25°C, VE = 2 V (unless otherwise noted). Limits Characteristic Symbol Output Voltage VO VO(off) Test Conditions Min. Typ. Max. Units VI = 3.3 V, IO = 10 mA 2.45 2.50 2.55 V VE = 0 V — — 0.5 V Output Volt. Temp. Coeff. aVO 0°C ≤ TJ ≤ 100°C — ±0.3 — mV/°C Output Short-Circuit Current IOM VI = 3.3 V, see note 3.2 — — A Line Regulation ∆VO(∆VI) VI = 3.0 ~ 5.0 V, IO = 10 mA — — 10 mV Load Regulation ∆VO(∆IO) VI = 3.3 V, IO = 0 A ~ 3.0 A — — 40 mV Dropout Voltage VImin - VO IO = 3.0 A — — 0.7 V VI = 3.3 V, IO = 0 mA, VE = 2.0 V — 1.0 1.5 mA VI = 3.3 V, VE = 0 V — — 1.0 µA VEH Output ON 2.0 — — V VEL Output OFF — — 0.8 V IEH VE = 2.7 V — — 100 µA IEL VE = 0 V — 0 -5.0 µA VI = 3.3 V, 100 Hz ≤ f ≤ 120 Hz — 60 — dB 135 152 — °C Ground Terminal Current Enable Input Voltage Enable Input Current Ripple Rejection Ratio Thermal Shutdown IGND PSRR TJ Typical values are given for circuit design information only. Note: Output short-circuit current is at point where output voltage has decreased 5% below VO(nom). www.allegromicro.com 3 ar ors e n t Li ula g Re SI-3025ZF High-Current, Low-Dropout, 2.5 V Regulator TYPICAL CHARACTERISTICS (TA = 25°C) 4 Dropout Voltage Low-Voltage Behavior GND Pin Current Line Regulation Load Regulation Overcurrent Protection ENABLE Control Voltage ENABLE Control Current Thermal Protection 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 ar ors e n t Li ula g e R SI-3025ZF High-Current, Low-Dropout, 2.5 V Regulator APPLICATIONS INFORMATION Input Capacitor (CI, approximately 10 µF). This is necessary either when the input line includes inductance or when the wiring is long. Output Capacitor (CO, > 47 µF). This device is not designed for a use with a very low ESR output capacitor such as a ceramic capacitor. Output oscillation may occur with that kind of capacitor. Determination of DC Input Voltage. The minimum input voltage VI(min) should be higher than the sum of the fixed output voltage and the maximum rated dropout voltage. Increased Output Voltage. The output voltage (VO) may be increased by inserting a resistor (REXT) between SENSE and OUTPUT. The current flowing into SENSE is typically 90 µA ±30%. To minimize the effect of ISENSE and temperature on REXT, it is recommended that a 6.8 kΩ resistor be added between SENSE and GND to increase the current in REXT. The value of REXT is then 6 REXT = (VO – 2.5) × 10 /458 Overcurrent Protection. The SI-3000ZD series has a built-in fold-back type overcurrent protection circuit, which limits the output current at a start-up mode. It thus cannot be used in applications that require current at the start-up mode such as: (1) constant-current load, (2) power supply with positive and negative outputs to common load (a center-tap type power supply), or (3) raising the output voltage by putting a diode or a resistor between the device ground and system ground. Heat Radiation and Reliability. The reliability of the IC is directly related to the junction temperature (TJ) in its operation. Accordingly, careful consideration should be given to heat dissipation. The graph on page 2 illustrates the effect of thermal resistance on the allowable package power dissipation. When mounting to a heat sink, apply silicone grease (ShinEtsu Chemical G746, Dow Corning Toray Silicone SC102, or Toshiba Silicone SY6260). Recommended mounting hardware torque: 0.588 ~ 0.686 Nm or 6.0 ~ 7.0 kgf•cm (4.34 ~ 5.06 lbf•ft). The junction temperature (TJ) can be determined from either of the following equations: TJ = (PD × RθJA) + TA or TJ = (PD × RθJC) + TC where PD = IO × (VI – VO) and RθJC = 5°C/W. Parallel Operation. Parallel operation to increase load current is not permitted. Thermal Protection. Circuitry turns off the pass transistor when the junction temperature rises above 135°C. It is intended only to protect the device from failures due to excessive junction temperatures and should not imply that output short circuits or continuous overloads are permitted. www.allegromicro.com 5 ar ors e n t Li ula g Re SI-3025ZF High-Current, Low-Dropout, 2.5 V Regulator Dimensions in Millimeters Terminal Finish: Sn–3Ag–0.5Cu, 2nd level interconnect category (e1) Product Weight: Approx. 2.3 g Terminal spacing is measured at lead tips. 6 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 ar ors e n t Li ula g e R SI-3025ZF High-Current, Low-Dropout, 2.5 V Regulator Shipping Container Dimensions in Millimeters Primary Packing: A U-shaped cardboard separator (Fig. 1) is used to accommodate a maximum of 100 pieces (5 × 20) and, if less than 100 pieces, a shock absorber shall be placed in the vacant space. Each thin primary carton (Fig. 2) will contain a maximum of 400 pieces in four rows. Secondary Packing: The secondary carton (Fig. 3) contains nine thin cartons. EI16EI www.allegromicro.com 7 ar ors e n t Li ula g Re SI-3025ZF High-Current, Low-Dropout, 2.5 V Regulator The products described herein are manufactured in Japan by Sanken Electric Co., Ltd. for sale by Allegro MicroSystems, Inc. Sanken and Allegro reserve the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Therefore, the user is cautioned to verify that the information in this publication is current before placing any order. When using the products described herein, the applicability and suitability of such products for the intended purpose shall be reviewed at the users responsibility. Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to society due to device failure or malfunction. Sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Their use in any application requiring radiation hardness assurance (e.g., aerospace equipment) is not supported. When considering the use of Sanken products in applications where higher reliability is required (transportation equipment and its control systems or equipment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to discuss and obtain written confirmation of your specifications. The use of Sanken products without the written consent of Sanken in applications where extremely high reliability is required (aerospace equipment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited. The information included herein is believed to be accurate and reliable. Application and operation examples described in this publication are given for reference only and Sanken and Allegro assume no responsibility for any infringement of industrial property rights, intellectual property rights, or any other rights of Sanken or Allegro or any third party that may result from its use. 8 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036