TI TPS2115APW

! "" # ! ""$
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
FEATURES
D Two-Input, One-Output Power Multiplexer
D
D
APPLICATIONS
D
D
D
D
D
D
D
With Low rDS(on) Switches:
− 84 mΩ Typ (TPS2115A)
− 120 mΩ Typ (TPS2114A)
Reverse and Cross-Conduction Blocking
Wide Operating Voltage Range . . . .2.8 V to
5.5 V
Low Standby Current . . . . 0.5-µA Typ
D
D Low Operating Current . . . . 55-µA Typ
D Adjustable Current Limit
D Controlled Output Voltage Transition Times,
PDAs
Digital Cameras
Modems
Cell Phones
Digital Radios
MP3 Players
PW PACKAGE
(TOP VIEW)
STAT
D0
D1
ILIM
Limits Inrush Current and Minimizes Output
Voltage Hold-Up Capacitance
D
D
D
D
PCs
CMOS- and TTL-Compatible Control Inputs
Manual and Auto-Switching Operating Modes
Thermal Shutdown
Available in a TSSOP-8 Package
1
2
3
4
8
7
6
5
IN1
OUT
IN2
GND
DESCRIPTION
The TPS211xA family of power multiplexers enables seamless transition between two power supplies, such as a battery
and a wall adapter, each operating at 2.8−5.5 V and delivering up to 1 A. The TPS211xA family includes extensive protection
circuitry, including user-programmable current limiting, thermal protection, inrush current control, seamless supply
transition, cross-conduction blocking, and reverse-conduction blocking. These features greatly simplify designing power
multiplexer applications.
TYPICAL APPLICATION
Switch Status
IN1: 2.8 − 5.5 V
TPS2115APW
1 STAT
2
3
4
D0
D1
ILIM
IN1
0.1 µF
R1
8
OUT 7
IN2
GND
6
CL
5
RL
RILIM
IN2: 2.8 − 5.5 V
0.1 µF
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
%
% &'()"(& * ))& * (' +,(& -. )(-*
(&'()" ( *+'(&* +) / )"* (' #* &*)"&* *&-)- 0))&1.
)(-(& +)(**&2 -(* &( &**)1 &- *&2 (' +)")*.
Copyright  2004, Texas Instruments Incorporated
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during
storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE OPTIONS
FEATURE
TPS2110A
TPS2111A
TPS2112A
TPS2113A
TPS2114A
TPS2115A
Current Limit Adjustment Range
0.31−0.75A
0.63−1.25A
0.31−0.75A
0.63−1.25A
0.31−0.75A
0.63−1.25A
Manual
Yes
Yes
No
No
Yes
Yes
Automatic
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
TSSOP-8
TSSOP-8
TSSOP-8
TSSOP-8
TSSOP-8
TSSOP-8
Switching Modes
Switch Status Output
Package
ORDERING INFORMATION
TA
PACKAGE
−40°C to 85°C
TSSOP-8 (PW)
ORDERING NUMBER(1)
MARKINGS
TPS2114APW
2114A
TPS2115APW
2115A
(1) The PW package is available taped and reeled. Add an R suffix to the device type (e.g., TPS2114APWR) to indicate tape and reel.
PACKAGE DISSIPATION RATINGS
PACKAGE
TSSOP-8 (PW)
DERATING FACTOR ABOVE
TA = 25°C
3.9 mW/°C
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
387 mW
213 mW
155 mW
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted(1)
TPS2114A, TPS2115A
Input voltage range at pins IN1, IN2, D0, D1, ILIM(2)
Output voltage range, VO(OUT), VO(STAT)(2)
−0.3 V to 6 V
−0.3 V to 6 V
Output sink current, IO(STAT)
Continuous output current, IO
5 mA
TPS2114A
0.9 A
TPS2115A
1.5 A
Continuous total power dissipation
See Dissipation Rating Table
Operating virtual junction temperature range, TJ
−40°C to 125°C
Storage temperature range, Tstg
−65°C to 150°C
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds
260°C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to GND.
RECOMMENDED OPERATING CONDITIONS
MIN
MAX UNIT
1.5
5.5
Input voltage at IN1, VI(IN1)
VI(IN2) ≥ 2.8 V
VI(IN2) < 2.8 V
2.8
5.5
VI(IN1) ≥ 2.8 V
VI(IN1) < 2.8 V
1.5
5.5
Input voltage at IN2, VI(IN2)
2.8
5.5
Input voltage, VI(DO), VI(D1)
Current limit adjustment range, IO(OUT)
0
5.5
TPS2114A
0.31
0.75
TPS2115A
0.63
1.25
−40
125
Operating virtual junction temperature, TJ
V
V
V
A
°C
ELECTROSTATIC DISCHARGE (ESD) PROTECTION
MIN
Human body model
CDM
2
MAX UNIT
2
kV
500
V
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
ELECTRICAL CHARACTERISTICS
over recommended operating junction temperature range, VI(IN1) = VI(IN2) = 5.5 V, RILIM = 400 Ω (unless otherwise noted)
TPS2114A
PARAMETER
TEST CONDITIONS
MIN
TPS2115A
TYP
MAX
VI(IN1) = VI(IN2) = 5.0 V
VI(IN1) = VI(IN2) = 3.3 V
120
120
VI(IN1) = VI(IN2) = 2.8 V
VI(IN1) = VI(IN2) = 5.0 V
120
MIN
TYP
MAX
140
84
110
140
84
110
140
84
110
UNIT
POWER SWITCH
rDS(on)(1)
Drain-source
on-state resistance
(INx−OUT)
TJ = 25°C,
IL = 500 mA
TJ = 125°C,
IL = 500 mA
VI(IN1) = VI(IN2) = 3.3 V
VI(IN1) = VI(IN2) = 2.8 V
220
150
220
150
220
150
mΩ
mΩ
m
(1) The TPS211xA can switch a voltage as low as 1.5 V as long as there is a minimum of 2.8 V at one of the input power pins. In this specific case,
the lower supply voltage has no effect on the IN1 and IN2 switch on-resistances.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LOGIC INPUTS (D0 AND D1)
VIH High-level input voltage
VIL Low-level input voltage
Input current at D0 or D1
2
V
0.7
D0 or D1 = High, sink current
D0 or D1 = Low, source current
1
0.5
1.4
5
55
90
1
12
V
µA
SUPPLY AND LEAKAGE CURRENTS
Supply current from IN1
(operating)
Supply current from IN2
(operating)
Quiescent current from IN1
(STANDBY)
Quiescent current from IN2
(STANDBY)
Forward leakage current from IN1
(measured from OUT to GND)
D1 = High, D0 = Low (IN1 active), VI(IN1) = 5.5 V, VI(IN2) = 3.3 V,
IO(OUT) = 0 A
D1 = High, D0 = Low (IN1 active), VI(IN1) = 3.3 V, VI(IN2) = 5.5 V,
IO(OUT) = 0 A
D0 = D1 = Low (IN2 active), VI(IN1) = 5.5 V, VI(IN2) = 3.3 V,
IO(OUT) = 0 A
D0 = D1 = Low (IN2 active), VI(IN1) = 3.3 V, VI(IN2) = 5.5 V,
IO(OUT) = 0 A
D1 = High, D0 = Low (IN1 active), VI(IN1) = 5.5 V, VI(IN2) = 3.3 V,
IO(OUT) = 0 A
D1 = High, D0 = Low (IN1 active), VI(IN1) = 3.3 V, VI(IN2) = 5.5 V,
IO(OUT) = 0 A
D0 = D1 = Low (IN2 active), VI(IN1) = 5.5 V, VI(IN2)= 3.3 V,
IO(OUT) = 0 A
D0 = D1 = Low (IN2 active), VI(IN1) = 3.3 V, VI(IN2) = 5.5 V,
IO(OUT) = 0 A
D0 = D1 = High (inactive),
IO(OUT) = 0 A
D0 = D1 = High (inactive),
IO(OUT) = 0 A
D0 = D1 = High (inactive),
IO(OUT) = 0 A
D0 = D1 = High (inactive),
IO(OUT) = 0 A
VI(IN1) = 5.5 V, VI(IN2) = 3.3 V,
µA
75
1
1
75
µA
1
12
55
90
0.5
2
µA
VI(IN1) = 3.3 V, VI(IN2) = 5.5 V,
1
VI(IN1) = 5.5 V, VI(IN2) = 3.3 V,
1
VI(IN1) = 3.3 V, VI(IN2) = 5.5 V,
Forward leakage current from IN2
(measured from OUT to GND)
D0 = D1 = High (inactive), VI(IN1) = 5.5 V, IN2 open,
VO(OUT) = 0 V (shorted), TJ = 25°C
D0 =D1= High (inactive), VI(IN2) = 5.5 V, IN1 open,
VO(OUT) = 0 V (shorted), TJ = 25°C
Reverse leakage current to INx
(measured from INx to GND)
D0 = D1 = High (inactive), VI(INx) = 0 V, VO(OUT) = 5.5 V, TJ = 25°C
µA
0.5
2
0.1
5
µA
0.1
5
µA
0.3
5
µA
3
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
ELECTRICAL CHARACTERISTICS (Continued)
over recommended operating junction temperature range, VI(IN1) = VI(IN2) = 5.5 V, RILIM = 400 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
CURRENT LIMIT CIRCUIT
TPS2114A
RILIM = 400 Ω
RILIM = 700 Ω
0.51
0.63
0.80
0.30
0.36
0.50
TPS2115A
RILIM = 400 Ω
RILIM = 700 Ω
0.95
1.25
1.56
0.47
0.71
0.99
Current limit accuracy
td
Current limit settling time(1)
Time for short-circuit output current to
settle within 10% of its steady state value.
Input current at ILIM
VI(ILIM) = 0 V, IO(OUT) = 0 A
1
−15
A
ms
0
µA
(1) Not tested in production.
PARAMETER
TEST CONDITIONS
MIN
TYP
1.15
1.25
MAX
UNIT
UVLO
Falling edge
IN1 and IN2 UVLO
Rising edge
IN1 and IN2 UVLO hysteresis(1)
Falling edge
Internal VDD UVLO (the higher of IN1 and IN2)
Rising edge
Internal VDD UVLO hysteresis(1)
UVLO deglitch for IN1, IN2(1)
Falling edge
1.30
1.35
30
57
65
2.4
2.53
30
2.58
2.8
50
75
V
mV
V
mV
µs
110
(1) Not tested in production.
MIN
TYP
MAX
UNIT
80
100
120
mV
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Thermal shutdown threshold(1)
TPS211xA is in current limit.
135
Recovery from thermal shutdown(1)
Hysteresis(1)
TPS211xA is in current limit.
125
PARAMETER
TEST CONDITIONS
REVERSE CONDUCTION BLOCKING
∆VO(I_block)
Minimum output-to-input voltage
difference to block switching
PARAMETER
D0 = D1 = high, VI(INx) = 3.3 V. Connect OUT to a 5 V
supply through a series 1-kΩ resistor. Let D0 = low.
Slowly decrease the supply voltage until OUT connects
to IN1.
THERMAL SHUTDOWN
°C
C
10
IN2−IN1 COMPARATORS
Hysteresis of IN2−IN1 comparator
0.1
0.2
V
Deglitch of IN2−IN1 comparator (both ↑↓)(1)
(1) Not tested in production.
10
20
50
µs
MIN
TYP
MAX
PARAMETER
TEST CONDITIONS
UNIT
STAT OUTPUT
Leakage current
Saturation voltage
Deglitch time (falling edge only)
4
VO(STAT) = 5.5 V
II(STAT) = 2 mA, IN1 switch is on
0.01
1
µA
0.13
0.4
V
150
µs
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
SWITCHING CHARACTERISTICS
over recommended operating junction temperature range, VI(IN1) = VI(IN2) = 5.5 V, RILIM = 400 Ω (unless otherwise noted)
TPS2114A
PARAMETER
TEST CONDITIONS
TPS2115A
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
POWER SWITCH
tr
Output rise time from
an enable(1)
VI(IN1) = VI(IN2) = 5 V
TJ = 25°C, CL = 1 µF,
IL = 500 mA,
See Figure 1(a)
0.5
1.0
1.5
1
1.8
3
ms
tf
Output fall time from
a disable(1)
VI(IN1) = VI(IN2) = 5 V
TJ = 25°C, CL = 1 µF,
IL = 500 mA,
See Figure 1(a)
0.35
0.5
0.7
0.5
1
2
ms
40
60
40
60
tt
Transition time(1)
IN1 to IN2 transition,
VI(IN1) = 3.3 V,
VI(IN2) = 5 V
IN2 to IN1 transition,
VI(IN1) = 5 V,
VI(IN2) = 3.3 V
tPLH1
Turn-on propagation
delay from enable(1)
tPHL1
Turn-off propagation
delay from a
disable(1)
tPLH2
Switch-over rising
propagation delay(1)
tPHL2
Switch-over falling
propagation delay(1)
VI(IN1) = VI(IN2) = 5 V
Measured from enable to
10% of VO(OUT)
VI(IN1) = VI(IN2) = 5 V,
Measured from disable
to 90% of VO(OUT)
Logic 1 to Logic 0
transition on D1,
VI(IN1) = 1.5 V,
VI(IN2) = 5 V,
VI(D0) = 0 V,
Measured from D1 to
10% of VO(OUT)
Logic 0 to Logic 1
transition on D1,
VI(IN1) = 1.5V,
VI(IN2) = 5V,
VI(D0) = 0 V,
Measured from D1 to
90% of VO(OUT)
TJ = 125°C, CL = 10 µF,
IL = 500 mA
[Measure transition time
as 10−90% rise time or
from 3.4 V to 4.8 V on
VO(OUT)],
See Figure 1(b)
µs
40
60
40
60
TJ = 25°C, CL = 10 µF,
IL = 500 mA,
See Figure 1(a)
0.5
1
ms
TJ = 25°C, CL = 10 µF,
IL = 500 mA,
See Figure 1(a)
3
5
ms
TJ = 25°C, CL = 10 µF,
IL = 500 mA,
See Figure 1(c)
40
100
3
10
TJ = 25°C, CL = 10 µF,
IL = 500 mA,
See Figure 1(c)
2
2
40
100
µs
5
10
ms
(1) Not tested in production.
5
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TRUTH TABLE
D1
D0
0
0
0
1
0
1
1
0
1
1
STAT
Hi-Z
OUT(1)
No
0
IN1
Yes
Hi-Z
IN2
X
0
IN1
X
0
Hi-Z
VI(IN2) > VI(IN1)
X
IN2
X = Don’t care.
(1)The under-voltage lockout circuit causes the output OUT to go Hi-Z if the
selected power supply does not exceed the IN1/IN2 UVLO, or if neither
of the supplies exceeds the internal VDD UVLO
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
D0
2
I
D1
3
I
TTL- and CMOS-compatible input pins. Each pin has a 1-µA pull-up. The truth table shown above illustrates the
functionality of D0 and D1.
GND
5
I
Ground
IN1
8
I
Primary power switch input. The IN1 switch can be enabled only if the IN1 supply is above the UVLO threshold and at
least one supply exceeds the internal VDD UVLO.
IN2
6
I
Secondary power switch input. The IN2 switch can be enabled only if the IN2 supply is above the UVLO threshold and
at least one supply exceeds the internal VDD UVLO.
ILIM
4
I
A resistor RILIM from ILIM to GND sets the current limit IL to 250/RILIM and 500/RILIM for the TPS2114A and TPS2115A,
respectively.
OUT
7
O
Power switch output
STAT
1
O
STAT is an open-drain output that is Hi-Z if the IN2 switch is ON. STAT pulls low if the IN1 switch is ON or if OUT is Hi-Z
(i.e., EN is equal to logic 0).
6
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
FUNCTIONAL BLOCK DIAGRAM
1 µA
IN1
IN2
1 µA
Internal VDD
Vf = 0 V
Vf = 0 V
IO(OUT)
Q1
8
Q2
6
7
Charge
Pump
VDD
ULVO
IN2
ULVO
IN1
ULVO
Cross-Conduction
Detector
+
_
0.6 V
+
EN2
k* IO(OUT)
_
TPS2114A: k = 0.2%
TPS2115A: k = 0.1%
+
0.5 V
+
_
VO(OUT) > VI(INx)
UVLO (IN2)
UVLO (IN1)
D1
GND
3
+
_
100 mV
+
EN1
D0
D1
ILIM
Q1 is ON
UVLO (VDD)
2
4
EN1
Q2 is ON
D0
OUT
Control
Logic
Thermal
Sense
IN2
+
_
5
IN1
1
STAT
Q2 is ON
7
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
90%
90%
VO(OUT)
10%
10%
0V
tr
tf
tPLH1
tPHL1
DO−D1
Switch Off
Switch Enabled
Switch Off
(a)
5V
4.8 V
VO(OUT)
3.4 V
3.3 V
tt
DO−D1
Switch #2 Enabled
Switch #1 Enabled
(b)
5V
VO(OUT)
1.5 V
4.65 V
1.85 V
tPLH2
tPHL2
DO−D1
Switch #1 Enabled
Switch #2 Enabled
Switch #1 Enabled
(c)
Figure 1. Propagation Delays and Transition Timing Waveforms
8
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TYPICAL CHARACTERISTICS
OUTPUT SWITCHOVER RESPONSE
VI(DO)
2V/Div
5V
TPS2115APW
NC
2
f = 28 Hz
78% Duty Cycle
VI(D1)
2V/Div
1
3
4
STAT
D0
D1
ILIM
400 Ω
0.1 µF
8
IN1
7
OUT
6
IN2
5
GND
50 Ω
1
µF
3.3 V
VO(OUT)
0.1 µF
2V/Div
Output Switchover Response Test Circuit
t − Time − 1 ms/div
Figure 2
OUTPUT TURN-ON RESPONSE
VI(DO)
2V/Div
5V
TPS2115APW
f = 28 Hz
78% Duty Cycle
VI(D1)
2V/Div
NC
1
2
3
4
400 Ω
STAT
IN1
0.1 µF
8
7
D0
OUT
D1
IN2
ILIM
GND
6
5
1
µF
50 Ω
3.3 V
VO(OUT)
2V/Div
0.1 µF
Output Turn-On Response Test Circuit
t − Time − 2 ms/div
Figure 3
9
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TYPICAL CHARACTERISTICS
OUTPUT SWITCHOVER VOLTAGE DROOP
VI(DO)
2V/Div
5V
TPS2115APW
NC
1
2
VI(D1)
2V/Div
CL = 1 µF
f = 580 Hz
90% Duty Cycle
3
4
400 Ω
VO(OUT)
2V/Div
STAT
D0
D1
ILIM
8
IN1
7
OUT
6
IN2
5
GND
0.1 µF
CL
0.1 µF
CL = 0 µF
Output Switchover Voltage Droop Test Circuit
t − Time − 40 µs/div
10
Figure 4
50 Ω
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TYPICAL CHARACTERISTICS
OUTPUT SWITCHOVER VOLTAGE DROOP
vs
LOAD CAPACITANCE
5
VI = 5 V
∆ VO(OUT) − Output Voltage Droop − V
4.5
4
3.5
RL = 10 Ω
3
2.5
2
1.5
RL = 50 Ω
1
0.5
0
0.1
VI
1
10
CL − Load Capacitance − µF
100
TPS2115APW
NC
1
2
f = 28 Hz
50% Duty Cycle
3
4
400 Ω
STAT
IN1
D0
OUT
D1
IN2
ILIM
GND
8
0.1 µF
7
6
5
50 Ω
0.1 µF
0.1 µF
1 µF
10 µF
47 µF
10 Ω
100 µF
Output Switchover Voltage Droop Test Circuit
Figure 5
11
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TYPICAL CHARACTERISTICS
AUTO SWITCHOVER VOLTAGE DROOP
VI(IN1)
2V/Div
5V
TPS2115A
1kΩ
1
STAT
2
f = 220 Hz
20% Duty Cycle
D0
3
4
400Ω
VO(OUT)
2V/Div
D1
ILIM
8
IN1
7
OUT
6
IN2
5
GND
0.1 µF
VOUT
3.3V 10 µF
0.1 µF
75% less output voltage
droop compared to TPS2115
Auto Switchover Voltage Droop Test Circuit
t − Time − 250 µs/div
12
Figure 6
50 Ω
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TYPICAL CHARACTERISTICS
INRUSH CURRENT
vs
LOAD CAPACITANCE
300
200
VI = 5 V
150
VI = 3.3 V
100
I
I
− Inrush Current − mA
250
50
0
0
VI
f = 28 Hz
90% Duty Cycle
20
40
60
80
CL − Load Capacitance − µF
100
TPS2115APW
NC
1
2
NC
3
4
400 Ω
STAT
IN1
D0
OUT
D1
IN2
ILIM
GND
8
0.1 µF
To Oscilloscope
7
6
5
50 Ω
0.1 µF
0.1 µF
1 µF
10 µF
47 µF
100 µF
Output Capacitor Inrush Current Test Circuit
Figure 7
13
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TYPICAL CHARACTERISTICS
SWITCH ON-RESISTANCE
vs
SUPPLY VOLTAGE
SWITCH ON-RESISTANCE
vs
JUNCTION TEMPERATURE
120
rDS(on) − Switch On-Resistance − m Ω
rDS(on) − Switch On-Resistance − m Ω
180
160
TPS2114A
140
120
TPS2115A
100
80
60
−50
TPS2114A
115
110
105
100
95
90
TPS2115A
85
80
0
50
100
TJ − Junction Temperature − °C
2
150
3
4
5
VI(INx) − Supply Voltage − V
Figure 8
Figure 9
IN1 SUPPLY CURRENT
vs
SUPPLY VOLTAGE
IN1 SUPPLY CURRENT
vs
SUPPLY VOLTAGE
0.96
60
Device Disabled
VI(IN2) = 0 V
IO(OUT) = 0 A
IN1 Switch is ON
VI(IN2) = 0 V
IO(OUT) = 0 A
58
I(IN1) − IN1 Supply Current − µ A
0.94
0.92
0.90
0.88
0.86
I
I I(IN1) − IN1 Supply Current − µ A
6
56
54
52
50
48
46
44
0.84
42
40
0.82
2
3
4
5
VI(IN1)− IN1 Supply Voltage − V
Figure 10
14
6
2
3
4
5
VI(IN1) − Supply Voltage − V
Figure 11
6
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
JUNCTION TEMPERATURE
SUPPLY CURRENT
vs
JUNCTION TEMPERATURE
1.2
70
I I(INx) − Supply Current − µ A
I I(INx) − Supply Current − µ A
1
80
Device Disabled
VI(IN1) = 5.5 V
VI(IN2) = 3.3 V
IO(OUT) = 0 A
II(IN1) = 5.5 V
0.8
0.6
0.4
60
IN1 Switch is ON
VI(IN1) = 5.5 V
VI(IN2) = 3.3 V
IO(OUT) = 0 A
II(IN1)
50
40
30
20
0.2
10
II(IN2) = 3.3 V
0
−50
0
50
100
TJ − Junction Temperature − °C
Figure 12
150
0
−50
II(IN2)
0
50
100
TJ − Junction Temperature − °C
150
Figure 13
15
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
APPLICATION INFORMATION
Some applications have two energy sources, one of which should be used in preference to another. Figure 14
shows a circuit that will connect IN1 to OUT until the voltage at IN1 falls below a user-specified value. Once
the voltage on IN1 falls below this value, the TPS2114A/5A will select the higher of the two supplies. This usually
means that the TPS2114A/5A will swap to IN2.
Switch Status
IN1: 2.8 − 5.5 V
TPS2115APW
1
NC
2
3
4
STAT
IN1
D0
OUT
D1
IN2
ILIM
GND
0.1 µF
R1
8
7
6
RL
CL
5
RILIM
IN2: 2.8 − 5.5 V
C2
0.1 µF
Figure 14. Auto-Selecting for a Dual Power Supply Application
In Figure 15, the multiplexer selects between two power supplies based upon the D1 logic signal. OUT connects
to IN1 if D1 is logic 1; otherwise, OUT connects to IN2. The logic thresholds for the D1 terminal are compatible
with both TTL and CMOS logic.
Switch Status
IN1: 2.8 − 5.5 V
TPS2115APW
1
2
3
4
STAT
IN1
D0
OUT
D1
IN2
ILIM
GND
0.1 µF
R1
8
7
6
CL
5
RILIM
IN2: 2.8 − 5.5 V
0.1 µF
Figure 15. Manually Switching Power Sources
16
RL
www.ti.com
SBVS044A − MARCH 2004 − REVISED MAY 2004
DETAILED DESCRIPTION
AUTO-SWITCHING MODE
D0 equal to logic 1 and D1 equal to logic 0 selects the auto-switching mode. In this mode, OUT connects to
the higher of IN1 and IN2.
MANUAL SWITCHING MODE
D0 equal to logic 0 selects the manual-switching mode. In this mode, OUT connects to IN1 if D1 is equal to logic
1, otherwise OUT connects to IN2.
N-CHANNEL MOSFETs
Two internal high-side power MOSFETs implement a single-pole double-throw (SPDT) switch. Digital logic
selects the IN1 switch, IN2 switch, or no switch (Hi-Z state). The MOSFETs have no parallel diodes so
output-to-input current cannot flow when the FET is off. An integrated comparator prevents turn-on of a FET
switch if the output voltage is greater than the input voltage.
CROSS-CONDUCTION BLOCKING
The switching circuitry ensures that both power switches will never conduct at the same time. A comparator
monitors the gate-to-source voltage of each power FET and allows a FET to turn on only if the gate-to-source
voltage of the other FET is below the turn-on threshold voltage.
REVERSE-CONDUCTION BLOCKING
When the TPS211xA switches from a higher-voltage supply to a lower-voltage supply, current can potentially
flow back from the load capacitor into the lower-voltage supply. To minimize such reverse conduction, the
TPS211xA will not connect a supply to the output until the output voltage has fallen to within 100 mV of the supply
voltage. Once a supply has been connected to the output, it will remain connected regardless of output voltage.
CHARGE PUMP
The higher of supplies IN1 and IN2 powers the internal charge pump. The charge pump provides power to the
current limit amplifier and allows the output FET gate voltage to be higher than the IN1 and IN2 supply voltages.
A gate voltage that is higher than the source voltage is necessary to turn on the N-channel FET.
CURRENT LIMITING
A resistor RILIM from ILIM to GND sets the current limit to 250/RILIM and 500/RILIM for the TPS2114A and
TPS2115A, respectively. Setting resistor RILIM equal to zero is not recommended as that disables current
limiting.
OUTPUT VOLTAGE SLEW-RATE CONTROL
The TPS2114A/5A slews the output voltage at a slow rate when OUT switches to IN1 or IN2 from the Hi-Z state
(see Truth Table). A slow slew rate limits the inrush current into the load capacitor. High inrush currents can
glitch the voltage bus and cause a system to hang up or reset. It can also cause reliability issues—like pit the
connector power contacts, when hot-plugging a load such as a PCI card. The TPS2114A/5A slews the output
voltage at a much faster rate when OUT switches between IN1 and IN2. The fast rate minimizes the output
voltage droop and reduces the output voltage hold-up capacitance requirement.
17
PACKAGE OPTION ADDENDUM
www.ti.com
17-Nov-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS2114APW
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS2114APWR
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS2114APWRG4
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS2115APW
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS2115APWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS2115APWR
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS2115APWRG4
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated