AAT4670 Dual-Input, Dual-Output Load Switches General Description Features The AAT4670 SmartSwitch™ is part of the Analogic Tech Application Specific Power MOSFET (ASPM™) line of products. The AAT4670 consists of dual, independent, 1A current limited, slew rate controlled P-channel MOSFET power switches with a dedicated source and drain pin assigned to each switch. The internal circuitry automatically derives power from the higher of the two input power source pins with a low operating quiescent current of 18µA. In shutdown mode, the supply current decreases to less than 1µA. The switches operate with inputs ranging from 2.2V to 5.5V, making them ideal for 2.5V, 3V and 5V systems. The dual configuration permits integration of the load switch function for systems with two different power busses. Independent under voltage lockout circuits will shut down the corresponding switch if its input voltage falls below the under voltage lockout threshold. If the die temperature reaches the thermal limit, both switches thermal cycle off and on indefinitely without damage until the thermal condition is removed. An open drain FAULT output signals an over current or over temperature condition for each channel. Input logic levels are TTL compatible. • • • • 2.2V to 5.5V input voltage range 1A current limit per channel 95mΩ typical RDS(ON) Fast transient response: • < 1µs response to short circuit Low 18µA quiescent current 1µA max with Switches off Slew rate controlled Thermal shutdown Fault flags with 3ms blanking Under voltage lockout Temp range -40 to 85ºC 8-pin SOP, TSSOP or MSOP packages Preliminary Information • • • • • • • • SmartSwitch™ Applications • • • • • • Notebook Computer PDA, Subnotebook USB ports Peripheral ports Hot swap supplies Media bay The AAT4670 is available in 8 pin SOP, TSSOP or MSOP specified over -40 to 85 °C temperature range. Typical Application AAT4670 7 INA INB 6 EN 1 INA INB EN GND CINA 1µF GND 4670.2002.1.0.92 CINB 1µF 4 OUTA OUTB FAULTA FAULTB 8 OUTA OUTB 5 2 3 FAULTA FAULTB COUTA 1µF COUTB 1µF GND 1 AAT4670 Dual-Input, Dual-Output Load Switches Pin Descriptions Pin # Symbol Function 1 EN 2 FAULTA Open drain output signals over-current for OUTA and over-temperature condition 3 FAULTB Open drain output signals over-current for OUTB and over-temperature condition 4 GND Ground connection 5 OUTA P-channel MOSFET drain channel A 6 INA P-channel MOSFET source channel A 7 INB P-channel MOSFET source channel B 8 OUTB Active-low Enable input (Logic low turns the switches on) P-channel MOSFET drain channel B Pin Configuration SOP-8 5 FAULTA FAULTB GND 2 8 7 3 6 4 5 OUTB INB INA OUTA EN 1 FAULTA FAULTB GND 2 8 7 2 6 4 1 1 3 EN MSOP-8 2 7 OUTB INB INA OUTA 1 FAULTA FAULTB GND 2 8 2 1 1 2 EN TSSOP-8 3 6 4 5 OUTB INB INA OUTA 4670.2002.1.0.92 AAT4670 Dual-Input, Dual-Output Load Switches Absolute Maximum Ratings (TA=25°C unless otherwise noted) Symbol Description VINA,B VOUTA,B VFAULTA,B IOUT TJ VESD TLEAD INA or INB to GND OUTA or OUTB to GND FAULTA or FAULTB to GND Output Current Operating Junction Temperature Range ESD Rating1 - HBM Maximum Soldering Temperature (at Leads) Value Units -0.3 to 6 -0.3 to 6 -0.3 to 6 Internally Limited -40 to 150 4000 300 V V V A °C V °C Note: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time. Note 1: Human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. Thermal Characteristics Symbol ΘJA PD Description Maximum Thermal Resistance2 (SOP-8) Maximum Power Dissipation2 (SOP-8) Value Units 100 1.25 °C/W W Note 2: Mounted on a demo board. Electrical Characteristics (VIN = 5V, TA = 25°C unless otherwise noted. Bold values designate -40 to 85°C temperature range) Symbol Description VIN IQ Conditions IQ(OFF) ISD(OFF) VUVLO Operation Voltage Quiescent Current Off Supply Current Off Switch Current Undervoltage Lockout VINA or VINB = 5V IOUTA = IOUTB = 0 EN = VIN, VINA=VINB =5V, OUTA, OUTB open EN = VIN, VINA=VINB =5V, VOUTA=VOUTB =0V RDS(ON) On-Resistance Channel A or B VIN=5.0V VIN=3.0V TCRDS ILIM t1 t2 t3 t4 VEN(L) Switch Resistance Tempco Current Limit Channel A or B Output Turn-On Delay Time Output Rise Time Output Turn-Off Delay Time Output Fall Time EN Input Low Voltage VEN(H) EN Input High Voltage IEN(SINK) tRESP VFAULTLOW ISINK Tblank TSD EN Input Leakage Current Loop Response FAULT logic Output Low FAULT Logic Output High Leakage Current Fault Blanking Time Over-temperature threshold VOUT < VIN - 0.5V VIN=5V, OUT=0 to 10%, RLOAD=20Ω VIN=5V, OUT=10% to 90%, RLOAD=20Ω VIN=5V, OUT=100% to 90%, RLOAD=20Ω VIN=5V, OUT=90% to 10%, RLOAD=20Ω VIN=2.7V to 5.5V3 VIN=2.7V to <3.6V VIN=3.6V to 5.5V VEN=5.5V VIN=5V ISINK = 1mA VFAULT = 5.5V Min Typ Max Units 2.2 5.5 40 1 1 2.2 130 150 18 1.0 V µA µA µA V 0.1 1.7 95 mΩ 105 2800 ppm/°C 1.25 1.50 A 100 1000 µs 100 1000 µs 10 20 µs 5 20 µs 0.8 V 2.0 2.4 V 0.01 750 0.5 3 125 1 0.4 1 µA ns V µA ms °C Note 3: For VIN outside this range consult typical EN threshold curve. 4670.2002.1.0.92 3 AAT4670 Dual-Input, Dual-Output Load Switches Typical Characteristics Quiescent Current vs. Temperature Quiescent Current vs. Input Voltage 20 18 25 16 20 14 Input (µA) Quiescent Current (µA) 30 15 10 6 4 5 2 0 0 -40 -20 0 20 40 60 80 100 120 0 1 2 3 4 5 6 Temperature (°C) Input (V) Off-Supply Current vs. Temperature Off-Switch Current vs. Temperature 1.0000 Off-Switch Current (µA) 1.0000 Off-Switch Current (µA) 12 10 8 0.1000 0.0100 0.0010 0.0001 0.0000 0.1000 0.0100 0.0010 0.0001 0.0000 -40 -20 0 20 40 60 80 100 120 -40 -20 0 Temperature (°C) 20 40 60 80 100 120 Temperature (°C) Current Limit vs. Output Voltage RDS(ON) vs. Temperature 1.4 150 1.2 140 RDS(ON) (mΩ) Output (A) 1.0 0.8 0.6 0.4 130 120 VIN=3V 110 100 90 VIN=5V 80 0.2 70 0.0 60 0 1 2 3 Output (V) 4 4 5 -40 -20 0 20 40 60 80 100 120 Temperature (°C) 4670.2002.1.0.92 AAT4670 Dual-Input, Dual-Output Load Switches Typical Characteristics Turn-ON/OFF Response with 20Ω 1µF loads FAULT Delay Start Into 0.6Ω Load EN (5V/div) FAULT (5V/div) ON (5V/div) OUTB (5V/div) INB = 5V FAULT (5V/div) OUTA (5V/div) INA = 3V VOUT (1V/div) IINA + IINB (200mA/div) IIN (500mA/div) 100µs/div 500µs/div Short Circuit Through 0.3Ω Short Circuit Through 0.6Ω 4 6 3 Output Current 2 0 Output Voltage 0 Input and Output (V) Input Voltage 6 8 0 1 2 3 Input Voltage 6 8 4 4 Output Current 2 0 0 Output Voltage -3 -1 12 Output (A) 9 Output (A) Input and Output (V) 8 -2 4 -4 -1 0 1 Time (µs) 2 3 4 Time (µs) Typical EN Threshold vs. VIN Thermal Shutdown Response ON (5V/div) FAULT (5V/div) VOUT (1V/div) IIN (500mA/div) EN Threshold (V) 2.4 2.2 2 1.8 VEN(H) 1.6 1.4 1.2 VEN(L) 1 0.8 0.6 1.5 200ms/div 4670.2002.1.0.92 2 2.5 3 3.5 4 4.5 5 5.5 VIN (V) 5 AAT4670 Dual-Input, Dual-Output Load Switches Functional Block Diagram INA OUTA ILIM Slew Rate UVLO EN OTMP UVLO ILIM Slew Rate INB OUTB FAULTA FAULTB GND Functional Description The AAT4670 dual channel load switch, implemented with isolated independent P-channel MOSFET devices, is ideal for applications where dual power supplies are in continuous use. Typical applications for this include products with multiple USB ports, or ports requiring protection that operate off of separate power supplies. The input power supplies can be any voltage between 2.2V and 5.5V in any combination; one supply is not required to be the higher voltage. Internally, the power supply for the control circuitry will automatically switch to the higher of the two supplies. In the case where the supplies are equal, +/- 30mV of hysteresis prevents the internal supply from oscillating between the two input supplies. The low impedance P-channel MOSFET devices are identical in size allowing for layout flexibility. They are controlled by a patented fast acting current loop, and respond to short circuits in a fraction of a microsecond, which eases requirements on the input capacitors. With such fast transient response time, the upstream power supply rail is naturally isolated from the protected port. The AAT4670 is internally protected from thermal damage by an over temperature detection circuit. If a high ambient temperature or an 6 over current condition causes the die temperature to reach the internal thermal limit, both power devices are switched off until the die temperature cools to a level below the thermal limit threshold. The device will thermal cycle indefinitely until the over current or high temperature condition is removed. Due to the high thermal conductivity of silicon and the size of the die, the temperature across the die is relatively uniform at high temperatures, and therefore, as a precaution, both power devices are switched off when the thermal threshold is reached. Since the power devices operate off of independent power supplies, independent under voltage lockout circuits are employed. If the power supply to one channel falls below the under voltage lockout threshold, the other channel will remain active. A current limit condition is reported by the open drain FAULT output associated with the appropriate channel. A thermal limit condition is reported by both FAULT outputs. A three millisecond blanking interval prevents false reporting during the charging of a capacitive load, which typically occurs during device turn-on, but may also occur during a port hot plug-in event. The AAT4670 is ideally suited for protection of peripheral ports such as USB, PS2 and parallel ports. 4670.2002.1.0.92 AAT4670 Dual-Input, Dual-Output Load Switches Applications Information Input Capacitor The input capacitors, CINA and CINB, protect the input power supplies from current transients generated by loads attached to the AAT4670. If a short circuit is suddenly applied to an output of the AAT4670, there is a 750 nanosecond period during which a large current flows before current limit circuitry activates. (See characteristic curve "Short Circuit Through 0.3Ω.") In this event, a properly sized input capacitor can dramatically reduce the voltage transient seen by the power supply and other circuitry upstream from the AAT4670. CIN should be located as close to the device VIN pin as practically possible. Ceramic, tantalum or aluminum electrolytic capacitors may be selected for CIN. There is no specific capacitor ESR requirement for CIN. However, for higher current operation, ceramic capacitors are recommended for CIN due to their inherent capability over tantalum capacitors to withstand input current surges from low impedance sources such as batteries in portable devices. Output Capacitor In order to insure stability while the current limit is active, a small capacitance of approximately 1µF is required on each output. No matter how big the output capacitor, output current is limited to the value set by the AAT4670 current limiting circuitry, allowing very large output capacitors to be used. For example, USB ports are specified to have at least 120µF of capacitance down stream from their controlling power switch. The current limiting circuit will allow an output capacitance of 1000µF or more without disturbing the upstream power supply. Attaching Loads Capacitive loads attached to the AAT4670 will charge at a rate no greater than the current limit setting. FAULT Output FAULT flags are provided to alert the system if an AAT4670 load is not receiving sufficient voltage to operate properly. If current limit or over temperature circuits in any combination are active for more than approximately three milliseconds, the associated FAULT flag is pulled to ground through approximately 100Ω. Removal of voltage or current transients of less than three milliseconds prevents capacitive loads connected to either 4670.2002.1.0.92 AAT4670 output from activating the associated FAULT flag when they are initially attached. Pull up resistances of 1kΩ to 100kΩ are recommended. Since FAULT is an open drain terminal, it may be pulled up to any unrelated voltage less than the maximum operating voltage of 5.5V, allowing for level shifting between circuits. Thermal Considerations Since the AAT4670 has internal current limit and over temperature protection, junction temperature is rarely a concern. However, if the application requires large currents in a hot environment, it is possible that temperature rather than current limit will be the dominant regulating condition. In these applications, the maximum current available without risk of an over temperature condition must be calculated. The maximum internal temperature while current limit is not active can be calculated using Equation 1. TJ(MAX) = IMAX2 × RDS(ON)(MAX) × RθJA + TA(MAX) In Equation 1, IMAX is the maximum current required by the load. RDS(ON)(MAX) is the maximum rated RDS(ON) of the AAT4670 at high temperature. RθJA is the thermal resistance between the AAT4670 die and the board onto which it is mounted. TA(MAX) is the maximum temperature that the PCB under the AAT4670 would be if the AAT4670 were not dissipating power. Equation 1 can be rearranged to solve for IMAX; Equation 2. IMAX= TSD(MIN) - TA(MAX) RDS(ON)(MAX) × RθJA TSD(MIN) is the minimum temperature required to activate the AAT4670 over temperature protection. With typical specification of 125°C, 115°C is a safe minimum value to use. For example, if an application is specified to operate in 50°C environments, the PCB operates at temperatures as high as 85°C. The application is sealed and its PCB is small, causing RθJA to be approximately 120°C/W. Using Equation 2, IMAX= 115 - 85 = 1.25 A 160m × 120 To prevent thermal limiting, the operating load current in the application must be less than 1.25A which lies in the current limiting range, so in this application, any operating current below the current limit threshold is allowed. 7 AAT4670 Dual-Input, Dual-Output Load Switches Timing Diagram EN OUT t1 t2 t3 t4 Ordering Information Package 8 Marking Part Number Bulk Tape and Reel SOP-8 AAT4670IAS-B1 AAT4670IAS-T1 TSSOP-8 AAT4670IHS-B1 AAT4670IHS-T1 MSOP-8 AAT4670IKS-B1 AAT4670IKS-T1 4670.2002.1.0.92 AAT4670 Dual-Input, Dual-Output Load Switches Package Information SOP-8 Dim E H D 7 (4x) A c A2 b y 4670.2002.1.0.92 e A1 Θ L A A1 A2 B C D E e H L Y θ1 Millimeters Min Max 1.35 1.75 0.10 0.25 1.45 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 5.80 6.20 0.40 1.27 0.00 0.10 0° 8° Inches Min Max 0.053 0.069 0.004 0.010 0.057 0.013 0.020 0.007 0.010 0.189 0.197 0.150 0.157 0.050 0.228 0.244 0.016 0.050 0.000 0.004 0° 8° Note: 1. PACKAGE BODY SIZES EXCLUDE MOLD FLASH PROTRUSIONS OR GATE BURRS. 2. TOLERANCE 0.1000mm (4mil) UNLESS OTHERWISE SPECIFIED 3. COPLANARITY: 0.1000mm 4. DIMENSION L IS MEASURED IN GAGE PLANE. 5. CONTROLLING DIMENSION IS MILLIMETER; CONVERTED INCH DIMENSIONS ARE NOT NECESSARILY EXACT. 9 AAT4670 Dual-Input, Dual-Output Load Switches TSSOP-8 Dim E D DETAIL A E1 A A1 A2 b c D-8 D-28 E E1 e L L1 R R1 θ1 θ2 Millimeters Min Max 1.05 1.20 0.05 0.15 1.05 0.25 0.30 0.127 2.90 3.10 9.60 9.80 4.30 4.50 6.20 6.60 0.65 BSC 0.50 0.70 1.0 0.09 0.09 0° 8° Inches Min Max 0.041 0.047 0.002 0.006 0.041 0.010 0.012 0.005 0.114 0.122 0.378 0.386 0.170 0.177 0.244 0.260 0.025 BSC 0.20 0.028 0.039 0.004 0.004 0° 8° 12° E 0.20 e R1 A2 A R θ1 A1 L b DETAIL A 10 θ2 L1 4670.2002.1.0.92 AAT4670 Dual-Input, Dual-Output Load Switches MSOP-8 t e1 E1 E PIN 1 L D t1 A2 A e 4670.2002.1.0.92 b GAUGE PLANE L1 A1 Dim e1 t1 C (1) A A1 A2 b C D E E1 e e1 L L1 L2 θ θ2 Millimeters Min Max 0.08 1.10 0.00 0.15 0.75 0.95 0.22 0.38 0.08 0.23 2.90 3.10 4.80 5.00 2.90 3.10 0.65 BSC 1.95 BSC 0.40 0.80 0.95 REF 0.254 BSC 0° 8° 5° 15° Inches Min Max 0.003 0.043 0.000 0.005 0.029 0.037 0.008 0.014 0.003 0.009 0.114 0.122 0.188 0.196 0.114 0.122 0.025 BSC 0.076 BSC 0.015 0.031 0.037 REF 0.010 BSC 0° 8° 5° 15° Note: 1. PACKAGE BODY SIZES EXCLUDE MOLD FLASH PROTRUSIONS OR GATE BURRS. 2. TOLERANCE± 0.1000mm (4mil) UNLESS OTHERWISE SPECIFIED 3. COPLANARITY: 0.1000mm 4. DIMENSION L IS MEASURED IN GAGE PLANE. 5. CONTROLLING DIMENSION IS MILLIMETER, CONVERTED INCH DIMENSIONS ARE NOT NECESSARILY EXACT. 11 AAT4670 Dual-Input, Dual-Output Load Switches This page intentionally left blank. Advanced Analogic Technologies, Inc. 1250 Oakmead Parkway, Suite 310, Sunnyvale, CA 94086 Phone (408) 524-9684 Fax (408) 524-9689 12 4670.2002.1.0.92