ELPIDA EBS52UC8APFA-7A

DATA SHEET
512MB Unbuffered SDRAM DIMM
EBS52UC8APFA (64M words × 64 bits, 2 banks)
Description
Features
The EBS52UC8APFA is 64M words × 64 bits, 2 banks
Synchronous Dynamic RAM Registered Module,
mounted 16 pieces of 256M bits SDRAM sealed in
TSOP package. This module provides high density
and large quantities of memory in a small space
without utilizing the surface mounting technology.
Decoupling capacitors are mounted on power supply
line for noise reduction.
• Fully compatible with 8 bytes DIMM: JEDEC
standard outline
• 168-pin socket type dual in line memory module
(DIMM)
 PCB height: 34.93mm (1.38inch )
 Lead pitch: 1.27mm
• 3.3V power supply
• Clock frequency: 133MHz (max.)
• LVTTL interface
• Data bus width: × 64 non-ECC
• Single pulsed /RAS
• 4 Banks can operates simultaneously and
independently
• Burst read/write operation and burst read/single write
operation capability
• Programmable burst length (BL): 1, 2, 4, 8
• 2 variations of burst sequence
 Sequential
 Interleave
• Programmable /CAS latency (CL): 2, 3
• Byte control by DQMB
• Refresh cycles: 8192 refresh cycles/64ms
• 2 variations of refresh
 Auto refresh
 Self refresh
Document No. E0208E20 (Ver. 2.0)
Date Published June 2002 (K) Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2001-2002
EBS52UC8APFA
Ordering Information
Part number
Clock frequency
MHz (max.)
/CAS latency Package
Contact pad
Mounted devices
EBS52UC8APFA-7A
EBS52UC8APFA-75*
133
133
2, 3
3
Gold
EDS2508APTA
168-pin DIMM
Note: 100MHz operation at /CAS latency = 2.
Pin Configurations
1 pin 10 pin 11 pin
40 pin 41 pin
85 pin 94 pin 95 pin 124 pin 125 pin
Pin No.
Pin name
Pin No.
Pin name
Pin No.
1
VSS
2
DQ0
43
VSS
44
NC
3
DQ1
45
4
DQ2
5
DQ3
6
84 pin
168 pin
Pin name
Pin No.
Pin name
85
VSS
127
VSS
86
DQ32
128
CKE0
/CS2
87
DQ33
129
/CS3
46
DQMB2
88
DQ34
130
DQMB6
47
DQMB3
89
DQ35
131
DQMB7
VDD
48
NC
90
VDD
132
NC
7
DQ4
49
VDD
91
DQ36
133
VDD
8
DQ5
50
NC
92
DQ37
134
NC
9
DQ6
51
NC
93
DQ38
135
NC
10
DQ7
52
NC
94
DQ39
136
NC
11
DQ8
53
NC
95
DQ40
137
NC
12
VSS
54
VSS
96
VSS
138
VSS
13
DQ9
55
DQ16
97
DQ41
139
DQ48
14
DQ10
56
DQ17
98
DQ42
140
DQ49
15
DQ11
57
DQ18
99
DQ43
141
DQ50
16
DQ12
58
DQ19
100
DQ44
142
DQ51
17
DQ13
59
VDD
101
DQ45
143
VDD
18
VDD
60
DQ20
102
VDD
144
DQ52
19
DQ14
61
NC
103
DQ46
145
NC
20
DQ15
62
NC
104
DQ47
146
NC
21
NC
63
CKE1
105
NC
147
NC
22
NC
64
VSS
106
NC
148
VSS
23
VSS
65
DQ21
107
VSS
149
DQ53
24
NC
66
DQ22
108
NC
150
DQ54
25
NC
67
DQ23
109
NC
151
DQ55
26
VDD
68
VSS
110
VDD
152
VSS
27
/WE
69
DQ24
111
/CAS
153
DQ56
28
DQMB0
70
DQ25
112
DQMB4
154
DQ57
29
DQMB1
71
DQ26
113
DQMB5
155
DQ58
30
/CS0
72
DQ27
114
/CS1
156
DQ59
Data Sheet E0208E20 (Ver. 2.0)
2
EBS52UC8APFA
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
31
NC
73
VDD
115
/RAS
157
VDD
32
VSS
74
DQ28
116
VSS
158
DQ60
33
A0
75
DQ29
117
A1
159
DQ61
34
A2
76
DQ30
118
A3
160
DQ62
35
A4
77
DQ31
119
A5
161
DQ63
36
A6
78
VSS
120
A7
162
VSS
37
A8
79
CLK2
121
A9
163
CLK3
38
A10 (AP)
80
NC
122
BA0
164
NC
39
BA1
81
NC
123
A11
165
SA0
40
VDD
82
SDA
124
VDD
166
SA1
41
VDD
83
SCL
125
CLK1
167
SA2
42
CLK0
84
VDD
126
A12
168
VDD
Pin Description
Pin name
Function
A0 to A12
Address input
 Row address
A0 to A12
 Column address A0 to A9
BA0, BA1
Bank select address
DQ0 to DQ63
Data input/output
/CS0 to /CS3
Chip select input
/RAS
Row enable (/RAS) input
/CAS
Column enable (/CAS) input
/WE
Write enable input
DQMB0 to DQMB7
Byte data mask
CLK0 to CLK3
Clock input
CKE0, CKE1
Clock enable input
SDA
Data input/output for serial PD
SCL
Clock input for serial PD
SA0 to SA2
Serial address input
VDD
Primary positive power supply
VSS
Ground
NC
No connection
Data Sheet E0208E20 (Ver. 2.0)
3
EBS52UC8APFA
Serial PD Matrix
Byte No.
Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value
Comments
0
Number of bytes used by module
manufacturer
1
0
0
0
0
0
0
0
80H
128 bytes
1
Total SPD memory size
0
0
0
0
1
0
0
0
08H
256 bytes
2
Memory type
0
0
0
0
0
1
0
0
04H
SDRAM
3
Number of row addresses bits
0
0
0
0
1
1
0
1
0DH
13
4
Number of column addresses bits
0
0
0
0
1
0
1
0
0AH
10
5
Number of banks
0
0
0
0
0
0
1
0
02H
2
6
Module data width
0
1
0
0
0
0
0
0
40H
64 bits
7
Module data width (continued)
0
0
0
0
0
0
0
0
00H
0
Module interface signal levels
0
0
0
0
0
0
0
1
01H
LVTTL
1
1
1
0
1
0
1
75H
7.5ns
1
0
1
0
1
0
0
54H
5.4ns
8
9
10
SDRAM cycle time at CL = 3
0
(highest /CAS latency)
SDRAM access from Clock at CL = 3
0
(highest /CAS latency)
11
Module configuration type
0
0
0
0
0
0
0
0
00H
None.
12
Refresh rate/type
1
0
0
0
0
0
1
0
82H
7.8µs
13
SDRAM width
0
0
0
0
1
0
0
0
08H
×8
14
Error checking SDRAM width
0
0
0
0
0
0
0
0
00H
None.
0
0
0
0
0
0
0
1
01H
1 CLK
1
0
0
0
1
1
1
1
8FH
1, 2, 4, 8, F
0
0
0
0
0
1
0
0
04H
4
0
0
0
0
0
1
1
0
06H
2, 3
0
0
0
0
0
0
0
1
01H
0
0
0
0
0
0
0
0
1
01H
0
15
16
17
18
19
20
SDRAM device attributes:
minimum clock delay for back-toback random column addresses
SDRAM device attributes:
Burst lengths supported
SDRAM device attributes: number of
banks on SDRAM device
SDRAM device attributes:
/CAS latency
SDRAM device attributes:
/CS latency
SDRAM device attributes:
/WE latency
21
SDRAM device attributes
0
0
0
0
0
0
0
0
00H
22
SDRAM device attributes: General
0
0
0
0
1
1
1
0
0EH
23
SDRAM cycle time at CL = 2
(2nd highest /CAS latency)
(-7A)
0
1
1
1
0
1
0
1
75H
7.5ns
1
0
1
0
0
0
0
0
A0H
10ns
24
SDRAM access from Clock at CL = 2
(2nd highest /CAS latency)
0
(-7A)
1
0
1
0
1
0
0
54H
5.4ns
0
1
1
0
0
0
0
0
60H
6ns
0
0
0
0
0
0
0
0
00H
0
0
0
0
1
1
1
1
0FH
15ns
0
0
0
1
0
1
0
0
14H
20ns
0
0
0
0
1
1
1
1
0FH
15ns
0
0
0
0
1
1
1
1
0FH
15ns
(-75)
(-75)
25 to 26
27
Minimum row precharge time
(-7A)
(-75)
28
Row active to row active min
(-7A)
(-75)
Data Sheet E0208E20 (Ver. 2.0)
4
EBS52UC8APFA
Byte No.
Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value
Comments
29
/RAS to /CAS delay min
(-7A)
0
0
0
0
1
1
1
1
0FH
15ns
0
0
0
1
0
1
0
0
14H
20ns
(-75)
30
Minimum /RAS pulse width
0
0
1
0
1
1
0
1
2DH
45ns
31
Density of each bank on module
0
1
0
0
0
0
0
0
40H
256MB
0
0
0
1
0
1
0
1
15H
1.5ns
0
0
0
0
1
0
0
0
08H
0.8ns
Data signal input setup time
0
0
0
1
0
1
0
1
15H
1.5ns
35
Data signal input hold time
0
0
0
0
1
0
0
0
08H
0.8ns
36 to 61
Superset information
0
0
0
0
0
0
0
0
00H
62
SPD data revision code
0
0
0
1
0
0
1
0
12H
63
Checksum for Bytes 0 to 62
(-7A)
1
0
0
1
0
0
1
0
92H
1
1
0
1
0
0
1
1
D3H
32
33
34
Address and command signal input
setup time
Address and command signal input
hold time
(-75)
1.2
64
Manufacturer’s JEDEC ID code
0
1
1
1
1
1
1
1
7FH
Continuation Code
65
Manufacturer’s JEDEC ID code
0
1
1
1
1
1
1
1
7FH
Continuation Code
66
Manufacturer’s JEDEC ID code
1
1
1
1
1
1
1
0
FEH
Elpida Memory
67 to 71
Manufacturer’s JEDEC ID code
0
0
0
0
0
0
0
0
00H
0
1
1
0
0
1
0
0
64H
1
1
1
1
1
1
1
1
FFH
72
Manufacturing location
73 to 90
Manufacturer’s part number
91 to 92
Revision code
93 to 94
Manufacturing date
95 to 98
Assembly serial number
99 to 125 Manufacturer specific data
126
127
Reserved (Intel specification
frequency)
Reserved (Intel specification /CAS#
latency support)
Data Sheet E0208E20 (Ver. 2.0)
5
100MHz
EBS52UC8APFA
Block Diagram
/WE
/CS0
/CS1
/CS2
DQMB0
DQ 0
DQ 1
DQ 2
DQ 3
DQ 4
DQ 5
DQ 6
DQ 7
DQ 7 DQM /CS
DQ 6
DQ 5
DQ 4
D0
DQ 3
DQ 2
DQ 1
DQ 0
/WE
DQ 7 DQM
/WE
DQ 0 DQM /CS
DQ 1
DQ 2
DQ 3
D8
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQ 0 DQM /CS
DQ 1
DQ 2
DQ 3
D9
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQ 16
DQ 17
DQ 18
DQ 19
DQ 20
DQ 21
DQ 22
DQ 23
DQ 7 DQM /CS
DQ 6
DQ 5
DQ 4
D2
DQ 3
DQ 2
DQ 1
DQ 0
/WE
DQ 0 DQM /CS
DQ 1
DQ 2
DQ 3
D10
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQ 4 DQM /CS
DQ 7
DQ 6
DQ 5
D3
DQ 3
DQ 2
DQ 1
DQ 0
/WE
DQ 3 DQM /CS
DQ 0
DQ 1
DQ 2
D11
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQ 7DQM /CS
DQ 6
DQ 5
DQ 4
D6
DQ 3
DQ 2
DQ 1
DQ 0
/WE
DQ 0 DQM /CS
DQ 1
DQ 2
DQ 3
D14
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQ 7 DQM /CS
DQ 6
DQ 5
DQ 4
D7
DQ 3
DQ 2
DQ 1
DQ 0
/WE
DQ 0 DQM /CS
DQ 1
DQ 2
DQ 3
D15
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQMB3
DQMB1
DQ 8
DQ 9
DQ 10
DQ 11
DQ 12
DQ 13
DQ 14
DQ 15
/CS3
DQMB2
DQ 6
DQ 5
DQ 4
DQ 3
DQ 2
DQ 1
DQ 0
/CS
D1
DQ 24
DQ 25
DQ 26
DQ 27
DQ 28
DQ 29
DQ 30
DQ 31
DQMB6
DQMB4
DQ 32
DQ 33
DQ 34
DQ 35
DQ 36
DQ 37
DQ 38
DQ 39
DQ 4 DQM /CS
DQ 7
DQ 6
DQ 5
D4
DQ 3
DQ 2
DQ 1
DQ 0
/WE
DQ 3 DQM /CS
DQ 0
DQ 1
DQ 2
D12
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQMB7
DQMB5
DQ 40
DQ 41
DQ 42
DQ 43
DQ 44
DQ 45
DQ 46
DQ 47
DQ 48
DQ 49
DQ 50
DQ 51
DQ 52
DQ 53
DQ 54
DQ 55
DQ 5 DQM /CS
DQ 7
DQ 6
DQ 4
D5
DQ 3
DQ 2
DQ 1
DQ 0
/WE
DQ 2 DQM /CS
DQ 0
DQ 1
DQ 3
D13
DQ 4
DQ 5
DQ 6
DQ 7
/WE
DQ 56
DQ 57
DQ 58
DQ 59
DQ 60
DQ 61
DQ 62
DQ 63
CLK0
SERIAL PD
CLK: D0, D1, D4, D5
CLK2
CLK: D2, D3, D6, D7
3.3 pF
3.3 pF
SDA
SCL
A0
A1
A2
CLK: D8, D9, D12, D13 CLK3
CLK1
CLK: D10, D11, D14, D15
3.3 pF
3.3 pF
SA0 SA1 SA2
A0 to A11
A0 to A11: D0 to D15
BA0, BA1
A13, A12: D0 to D15
VCC
V SS
CKE1
/CAS
/CAS: D0 to D15
CKE0
CKE: D0 to D7
D0 to D15
1. The value of all resistors is 10
2. D0 to D7: 256M bits SDRAM
10 kΩ
/RAS: D0 to D15
D0 to D15
C
Remarks
/RAS
except CKE1.
Data Sheet E0208E20 (Ver. 2.0)
6
CKE: D8 to D15
EBS52UC8APFA
Electrical Specifications
• All voltages are referenced to VSS (GND).
• After power up, wait more than 100 µs and then, execute power on sequence and CBR (Auto) refresh before
proper device operation is achieved.
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Voltage on any pin relative to VSS
VT
–0.5 to VDD + 0.5
(≤ 4.6 (max.))
V
Supply voltage relative to VSS
VDD
–0.5 to +4.6
V
Short circuit output current
IOS
50
mA
Power dissipation
PD
16
W
Operating temperature
TA
0 to +70
°C
Storage temperature
Tstg
–55 to +125
°C
Note
1
Notes: 1. SDRAM device specification
Caution
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
DC Operating Conditions (TA = 0 to +70°C) (SDRAM device specification)
Parameter
Symbol
min.
max.
Unit
Note
Supply voltage
VDD
3.0
3.6
V
1
VSS
0
0
V
2
Input high voltage
VIH
2.0
VDD + 0.3
V
3
Input low voltage
VIL
−0.3
0.8
V
4
Notes: 1.
2.
3.
4.
The supply voltage with all VDD pins must be on the same level.
The supply voltage with all VSS pins must be on the same level.
VIH (max.) = VDD + 2.0V for pulse width ≤ 3ns at VDD.
VIL (min.) = VSS − 2.0V for pulse width ≤ 3ns at VSS.
Data Sheet E0208E20 (Ver. 2.0)
7
EBS52UC8APFA
DC Characteristics1 (TA = 0 to 70°C, VDD = 3.3V ± 0.3V, VSS = 0V)
Parameter
Symbol
Grade
max.
Unit
Test condition
Notes
Operating current
ICC1
-7A
1280
mA
Burst length = 1
tRC = tRC (min.)
1, 2, 3
ICC1
-75
1120
mA
ICC2P
48
mA
CKE = VIL, tCK = 12ns
6
ICC2N
320
mA
CKE, /CS = VIH,
tCK = 12ns
4
ICC3P
64
mA
CKE = VIL, tCK = 12ns
1, 2, 6
ICC3N
480
mA
CKE, /CS = VIH,
tCK = 12ns
1, 2, 4
Burst operating current
ICC4
1320
mA
tCK = tCK (min.), BL = 4
1, 2, 5
Refresh current
ICC5
-7A
2240
mA
tRC = tRC (min.)
3
ICC5
-75
2000
mA
48
mA
VIH ≥ VDD – 0.2V
VIL ≤ 0.2V
7
Standby current in power down
Standby current in non power
down
Active standby current in power
down
Active standby current in non
power down
Self refresh current
ICC6
Notes: 1. ICC depends on output load condition when the device is selected. ICC (max.) is specified at the output
open condition.
2. One bank operation.
3. Input signals are changed once per one clock.
4. Input signals are changed once per two clocks.
5. Input signals are changed once per four clocks.
6. After power down mode, CLK operating current.
7. After self refresh mode set, self refresh current.
DC Characteristics2 (TA = 0 to 70°C, VDD = 3.3V ± 0.3V, VSS = 0V)
Parameter
Symbol
min.
max.
Unit
Test condition
Input leakage current
ILI
–16
16
µA
0 ≤ VIN ≤ VDD
Output leakage current
ILO
–3
3
µA
0 ≤ VOUT ≤ VDD
DQ = disable
Output high voltage
VOH
2.4
—
V
IOH = –4mA
Output low voltage
VOL
—
0.4
V
IOL = 4mA
Data Sheet E0208E20 (Ver. 2.0)
8
Notes
EBS52UC8APFA
Pin Capacitance (TA = 25°C, VDD = 3.3V ± 0.3V)
Parameter
Symbol
Input capacitance
Data input/output capacitance
Pins
max.
Unit
CI1
Address
TBD
pF
CI2
/RAS, /CAS, /WE
TBD
pF
CI3
CKE
TBD
pF
CI4
/CS
TBD
pF
CI5
CLK
TBD
pF
CI6
DQMB
TBD
pF
CI/O1
DQ
TBD
pF
Notes
AC Characteristics (TA = 0 to 70°C, VDD = 3.3V ± 0.3V, VSS = 0V) (SDRAM device specification)
-7A
-75
Parameter
Symbol
min.
min.
max.
Unit
Notes
System clock cycle time
tCK
7.5
7.5
—
Ns
1
CLK high pulse width
tCH
2.5
2.5
—
Ns
1
CLK low pulse width
tCL
2.5
2.5
—
Ns
1
Access time from CLK
tAC
—
—
5.4
Ns
1, 2
Data-out hold time
tOH
2.7
2.7
—
Ns
1, 2
CLK to Data-out low impedance
tLZ
1
1
—
Ns
1, 2, 3
CLK to Data-out high impedance
tHZ
—
—
5.4
Ns
1, 4
Input setup time
tSI
1.5
1.5
—
Ns
1
Input hold time
tHI
0.8
0.8
—
Ns
1
Ref/Active to Ref/Active command period tRC
60
67.5
—
Ns
1
Active to Precharge command period
tRAS
45
45
120000
Ns
1
Active command to column command
(same bank)
tRCD
15
20
—
Ns
1
Precharge to active command period
tRP
15
20
—
Ns
1
Write recovery or data-in to precharge
lead time
tDPL
15
15
—
Ns
1
Last data into active latency
tDAL
1
2CLK + 15ns
2CLK + 20ns
—
Active (a) to Active (b) command period tRRD
15
15
—
Ns
Transition time (rise and fall)
tT
0.5
0.5
5
Ns
Refresh period
(8192 refresh cycles)
tREF
—
—
64
Ms
Notes: 1.
2.
3.
4.
AC measurement assumes tT = 0.5ns. Reference level for timing of input signals is 1.4V.
Access time is measured at 1.4V. Load condition is CL = 50pF.
tLZ (min.) defines the time at which the outputs achieves the low impedance state.
tHZ (max.) defines the time at which the outputs achieves the high impedance state.
Data Sheet E0208E20 (Ver. 2.0)
9
EBS52UC8APFA
Test Conditions
• Input and output timing reference levels: 1.4V
• Input waveform and output load: See following figures
2.4V
0.4V
DQ
2.0V
0.8V
CL
tT
tT
Input Waveform and Output Load
Relationship Between Frequency and Minimum Latency (SDRAM device specification)
Parameter
-7A
Frequency (MHz)
133
133
133
tCK (ns)
7.5
7.5
7.5
Symbol
CL = 3
CL = 2
CL = 3
Notes
lRCD
2
2
3
1
lRC
8
8
9
1
lRAS
6
6
6
1
lRP
2
2
3
1
lDPL
2
2
2
1
lRRD
2
2
2
1
Self refresh exit time
lSREX
1
1
1
2
Last data in to active command
(Auto precharge, same bank)
lDAL
4
4
5
= [lDPL + lRP]
Self refresh exit to command input
lSEC
8
8
9
= [lRC]
3
Precharge command to high impedance
lHZP
3
2
3
lAPR
1
1
1
lEP
–2
–1
–2
lCCD
1
1
1
Write command to data in latency
lWCD
0
0
0
DQM to data in
lDID
0
0
0
DQM to data out
lDOD
2
2
2
/CAS latency
Active command to column command
(same bank)
Active command to active command
(same bank)
Active command to precharge command
(same bank)
Precharge command to active command
(same bank)
Write recovery or data-in to precharge
command (same bank)
Active command to active command
(different bank)
Last data out to active command
(Auto precharge, same bank)
Last data out to precharge (early
precharge)
Column command to column command
-75
CKE to CLK disable
lCLE
1
1
1
Register set to active command
lMRD
2
2
2
/CS to command disable
lCDD
0
0
0
Power down exit to command input
lPEC
1
1
1
Notes: 1. IRCD to IRRD are recommended value.
2. Be valid [DESL] or [NOP] at next command of self refresh exit.
3. Except [DESL] and [NOP]
Data Sheet E0208E20 (Ver. 2.0)
10
EBS52UC8APFA
Pin Functions
CLK0 to CLK3 (input pin): CLK is the master clock input to this pin. The other input signals are referred at CLK
rising edge.
/CS0 to /CS3 (input pin): When /CS is Low, the command input cycle becomes valid. When /CS is High, all inputs
are ignored. However, internal operations (bank active, burst operations, etc.) are held.
/RAS, /CAS and /WE (input pins): Although these pin names are the same as those of conventional DRAMs, they
function in a different way. These pins define operation commands (read, write, etc.) depending on the combination
of their voltage levels. For details, refer to the command operation section.
A0 to A12 (input pins): Row address (AX0 to AX12) is determined by A0 to A12 level at the bank active command
cycle CLK rising edge. Column address (AY0 to AY9) is determined by A0 to A9 level at the read or write command
cycle CLK rising edge. And this column address becomes burst access start address. A10 defines the precharge
mode. When A10 = High at the precharge command cycle, all banks are precharged. But when A10 = Low at the
precharge command cycle, only the bank that is selected by BA0 and BA1 (BA) is precharged.
BA0 and BA1 (input pin)
BA0 and BA1 are bank select signal (BA). (See Bank Select Signal Table)
[Bank Select Signal Table]
BA0
BA1
Bank 0
L
L
Bank 1
H
L
Bank 2
L
H
Bank 3
H
H
Remark: H: VIH. L: VIL.
CKE0, CKE1 (input pin): This pin determines whether or not the next CLK is valid. If CKE is High, the next CLK
rising edge is valid. If CKE is Low, the next CLK rising edge is invalid. This pin is used for power-down and clock
suspend modes.
DQMB0 to DQMB7 (input pins): Read operation: If DQMB is High, the output buffer becomes High-Z. If the
DQMB is Low, the output buffer becomes Low-Z.
Write operation: If DQMB is High, the previous data is held (the new data is not written). If DQMB is Low, the data
is written.
DQ0 to DQ63 (input/output pins): Data is input to and output from these pins.
VDD (power supply pins): 3.3V is applied.
VSS (power supply pins): Ground is connected.
Detailed Operation Part
Refer to the EDS2504APTA/08APTA/16APTA datasheet (E0272E).
Data Sheet E0208E20 (Ver. 2.0)
11
EBS52UC8APFA
Physical Outline
Front side
Unit: mm
3.00
(DATUM -A-)
4.80 Max
4.00 Min
(63.67)
3.00
Component area
(Front)
1
84
B
C
11.43
A
36.83
1.27
54.61
133.35
Back side
127.35
2 – φ 3.00
85
34.93
17.80
4.00
168
Component area
(Back)
(DATUM -A-)
Detail B
R FULL
Detail C
(DATUM -A-)
1.00
2.00 ± 0.10
R FULL
6.35
3.125 ± 0.125
6.35
3.125 ± 0.125
1.00 ± 0.05
1.27
0.050
0.20 ± 0.15
2.50 ± 0.20
Detail A
4.175
2.00 ± 0.10
Note: Tolerance on all dimensions ± 0.15 unless otherwise specified.
ECA-TS2-0049-01
Data Sheet E0208E20 (Ver. 2.0)
12
EBS52UC8APFA
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on
these components to prevent damaging them.
In particular, do not push module cover or drop the modules in order to protect from mechanical defects,
which would be electrical defects.
When re-packing memory modules, be sure the modules are not touching each other.
Modules in contact with other modules may cause excessive mechanical stress, which may damage the
modules.
MDE0202
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
Data Sheet E0208E20 (Ver. 2.0)
13
EBS52UC8APFA
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
[Product applications]
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
This product is not designed to be resistant to electromagnetic waves or radiation. This product must be
used in a non-condensing environment.
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
M01E0107
Data Sheet E0208E20 (Ver. 2.0)
14