SN54ALS299, SN74ALS299 8-BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3-STATE OUTPUTS SDAS220B – DECEMBER 1982 – REVISED DECEMBER 1994 • • • • • description These 8-bit universal shift /storage registers feature multiplexed I/O ports to achieve full 8-bit data handling in a single 20-pin package. Two function-select (S0, S1) inputs and two outputenable (OE1, OE2) inputs can be used to choose the modes of operation listed in the function table. S0 OE1 OE2 G/QG E/QE C/QC A/QA QA′ CLR GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC S1 SL QH′ H/QH F/QF D/QD B/QB CLK SR SN54ALS299 . . . FK PACKAGE (TOP VIEW) G/QG E/QE C/QC A/QA QA′ S1 • SN54ALS299 . . . J PACKAGE SN74ALS299 . . . DW OR N PACKAGE (TOP VIEW) OE2 OE1 S0 VCC • Multiplexed I/O Ports Provide Improved Bit Density Four Modes of Operation: – Hold (Store) – Shift Right – Shift Left – Load Data Operate With Outputs Enabled or at High Impedance 3-State Outputs Drive Bus Lines Directly Can Be Cascaded for n-Bit Word Lengths Direct Overriding Clear Applications: – Stacked or Push-Down Registers – Buffer Storage – Accumulator Registers Package Options Include Plastic Small-Outline (DW) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 300-mil DIPs 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 SL QH′ H/QH F/QF D/QD CLR GND SR CLK B/Q B • Synchronous parallel loading is accomplished by taking both S0 and S1 high. This places the 3-state outputs in the high-impedance state and permits data applied on the I/O ports to be clocked into the register. Reading out of the register can be accomplished while the outputs are enabled in any mode. Clearing occurs asynchronously when the clear (CLR) input is low. Taking either OE1 or OE2 high disables the outputs, but has no effect on clearing, shifting, or storing data. The SN54ALS299 is characterized for operation over the full military temperature range of – 55°C to 125°C. The SN74ALS299 is characterized for operation from 0°C to 70°C. Copyright 1994, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ALS299, SN74ALS299 8-BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3-STATE OUTPUTS SDAS220B – DECEMBER 1982 – REVISED DECEMBER 1994 FUNCTION TABLE INPUTS MODE I/O PORTS CLR S1 S0 OE1† OE2† CLK SL SR A/QA B/QB C/QC D/QD Clear L L L X L H L X H L L X L L X X X X X X X X X X L L X L L X L L X Hold H H L X L X L L L L X L X X X X QA0 QA0 QB0 QB0 Shift Right H H L L H H L L L L ↑ ↑ X X H L H L Shift Left H H H H L L L L L L ↑ ↑ H L X X Load H H H X X ↑ X X OUTPUTS F/QF L L X G/QG H/QH QA′ QH′ L L X E/QE L L X L L X L L X L L L L L L QC0 QC0 QD0 QD0 QE0 QE0 QF0 QF0 QG0 QG0 QH0 QH0 QA0 QA0 QH0 QH0 QAn QAn QBn QBn QCn QCn QDn QDn QEn QEn QFn QFn QGn QGn H L QGn QGn QBn QBn QCn QCn QDn QDn QEn QEn QFn QFn QGn QGn QHn QHn H L QBn QBn H L a b c d e f g h a h NOTE: a . . . h = the level of the steady-state input at inputs A through H, respectively. This data is loaded into the flip-flops while the flip-flop outputs are isolated from the I/O terminals. † When one or both output-enable inputs are high, the eight I/O terminals are disabled to the high-impedance state; however, sequential operation or clearing of the register is not affected. logic symbol‡ CLR OE1 9 2 SRG8 R & 3 3EN13 OE2 S0 S1 CLK SR 1 19 0 1 M 0 3 12 C4/1→/2← 11 7 A /QA B/QB D/QD E/QE F/QF G/QG H/QH SL Z5 3,4D 6, 13 C/QC Z6 6 14 5 15 4 16 18 3,4D 12, 13 Z12 17 2,4D QH′ ‡ This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 QA′ 3,4D 5, 13 13 8 1,4D POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ALS299, SN74ALS299 8-BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3-STATE OUTPUTS SDAS220B – DECEMBER 1982 – REVISED DECEMBER 1994 logic diagram (positive logic) S0 S1 SR (shift right serial input) CLK 1 19 18 11 Six Identical Channels Not Shown† 12 1D 1D C1 C1 R QA′ CLR OE1 OE2 SL (shift left serial input) R 17 8 9 QH′ 2 3 7 16 A /QA H /QH † I/O ports not shown: B/QB (13), C/QC (6), D/QD (14), E/QE (5), F/QF (15), and G/QG (4). absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡ Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Operating free-air temperature range, TA: SN54ALS299 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C SN74ALS299 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C ‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ALS299, SN74ALS299 8-BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3-STATE OUTPUTS SDAS220B – DECEMBER 1982 – REVISED DECEMBER 1994 recommended operating conditions SN54ALS299 VCC VIH Supply voltage VIL Low-level input voltage High-level input voltage IOH High level output current High-level IOL Low level output current Low-level TA Operating free-air temperature SN74ALS299 MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 2 2 QA′ or QH′ QA – QH QA′ or QH′ QA – QH – 55 V V 0.7 0.8 – 0.4 – 0.4 –1 – 2.6 4 8 12 24 125 UNIT 0 70 V mA mA °C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH All outputs VCC = 4.5 V, VCC = 4.5 V to 5.5 V, II = – 18 mA IOH = – 0.4 mA QA – QH VCC = 4 4.5 5V IOH = – 1 mA IOH = – 2.6 mA QA′ or QH′ VCC = 4 4.5 5V IOL = 4 mA IOL = 8 mA 0.25 0.4 5V VCC = 4 4.5 IOL = 12 mA IOL = 24 mA 0.25 0.4 VCC = 5 5.5 5V VI = 5.5 V VI = 7 V VCC = 5.5 V, VI = 2.7 V VOL QA – QH II A–H Any others IIH‡ IIL‡ IO§ ICC SN54ALS299 MIN TYP† MAX TEST CONDITIONS S0, S1, SR, SL Any others QA′ or QH′ QA – QH VCC = 5 5.5 5V V, VI = 0 0.4 4V VCC = 5 5.5 5V V, VO = 2 2.25 25 V VCC = 5.5 V SN74ALS299 MIN TYP† MAX – 1.5 VCC – 2 2.4 – 1.5 UNIT V VCC – 2 V 3.3 2.4 3.2 0.25 0.4 0.35 0.5 0.25 0.4 0.35 0.5 0.1 0.1 0.1 0.1 20 20 – 0.2 – 0.2 – 0.1 – 0.1 – 15 –70 – 15 –70 – 20 –112 – 30 –112 Outputs high 15 28 15 28 Outputs low 22 38 22 38 Outputs disabled 23 40 23 40 V mA µA mA mA mA † All typical values are at VCC = 5 V, TA = 25°C. ‡ For I/O ports (QA – QH), the parameters IIH and IIL include the off-state output current. § The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ALS299, SN74ALS299 8-BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3-STATE OUTPUTS SDAS220B – DECEMBER 1982 – REVISED DECEMBER 1994 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) SN54ALS299 fclock tw Clock frequency (at 50% duty cycle) Pulse duration tsu th Hold time after CLK↑ 0 17 SN74ALS299 MIN MAX 0 30 22 16.5 CLR low 12 10 Serial or parallel data Inactive-state setup time before CLK↑† MAX CLK high or low S0 or S1 Setup time before CLK↑ ↑ MIN 25 20 High 18 16 Low 15 6 CLR 15 15 S0 or S1 0 0 Serial or parallel data 0 0 UNIT MHz ns ns ns † Inactive-state setup time is also referred to as recovery time. switching characteristics (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) VCC = 4.5 V to 5.5 V, CL = 50 pF, R1 = 500 Ω, R2 = 500 Ω, TA = MIN to MAX‡ SN54ALS299 SN74ALS299 MIN fmax tPLH tPHL tPLH tPHL MAX 17 MIN MAX 30 MHz 2 19 4 13 4 25 7 19 2 21 5 15 4 25 8 18 QA – QH 6 29 6 22 QA′ or QH′ 6 29 6 22 5 22 6 16 6 27 8 22 5 27 7 17 6 26 8 22 1 15 1 8 4 38 5 15 1 16 1 12 4 34 8 25 CLK QA– QH CLK QA′′ or QH′′ tPHL CLR tPZH tPZL OE1 OE2 OE1, QA – QH tPZH tPZL S0 S1 S0, QA – QH tPHZ tPLZ OE1 OE2 OE1, QA – QH tPHZ tPLZ S0 S1 S0, QA – QH UNIT ns ns ns ns ns ns ns ‡ For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54ALS299, SN74ALS299 8-BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3-STATE OUTPUTS SDAS220B – DECEMBER 1982 – REVISED DECEMBER 1994 PARAMETER MEASUREMENT INFORMATION SERIES 54ALS/74ALS AND 54AS/74AS DEVICES 7V RL = R1 = R2 VCC S1 RL R1 Test Point From Output Under Test CL (see Note A) From Output Under Test RL Test Point From Output Under Test CL (see Note A) CL (see Note A) LOAD CIRCUIT FOR BI-STATE TOTEM-POLE OUTPUTS LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS 3.5 V Timing Input Test Point LOAD CIRCUIT FOR 3-STATE OUTPUTS 3.5 V High-Level Pulse 1.3 V R2 1.3 V 1.3 V 0.3 V 0.3 V Data Input tw th tsu 3.5 V 1.3 V 3.5 V Low-Level Pulse 1.3 V 0.3 V 1.3 V 0.3 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATIONS 3.5 V Output Control (low-level enabling) 1.3 V 1.3 V 0.3 V tPZL Waveform 1 S1 Closed (see Note B) tPLZ [3.5 V 1.3 V tPHZ tPZH Waveform 2 S1 Open (see Note B) 1.3 V VOL 0.3 V VOH 1.3 V 0.3 V [0 V 3.5 V 1.3 V Input 1.3 V 0.3 V tPHL tPLH VOH In-Phase Output 1.3 V 1.3 V VOL tPLH tPHL VOH Out-of-Phase Output (see Note C) 1.3 V 1.3 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. When measuring propagation delay items of 3-state outputs, switch S1 is open. D. All input pulses have the following characteristics: PRR ≤ 1 MHz, tr = tf = 2 ns, duty cycle = 50%. E. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuits and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated