UNIPAC OPTOELECTRONICS CORPORATION
Spec. No. 413-212-061
Version :
3
Total pages :
14
Date
:
2001 .01 .08
UB084S01 COLOR TFT-LCD
MODULE SPECIFICATION
MODEL NAME: UB084S01
The content of this technical information
is subject to change without notice.
Please contact Unipac or its agent for
further information.
Unipac copyright 2001
All rights reserved,
Copying forbidden.
Record of Revision
Version
Revise Date
1
26/Jun./2000
2
22/Sep./2000
Page
Content
First draft.
5
3.a. Change current consumption of power supply voltage
=> IA=310
220(Typ.)
=> IB=330
300(Max.)
7
c.(1). Change DE mode
8
e. Change VL=> -
441(Min.)
(505)
Change IL=> -
490(Typ.)
539(Max.)
3(Min.)
Change PL=> (2.3)
2.25(Typ.)
Change VS=> 750
(910) (Typ.) T=0
550
Change FL=> 9
(700) (Typ.) T= 25
50(Min.)
80(Max.)
C. Change CR=>200
250(Typ.) & add Note 3
Change Brightness=> 150(Typ.) Remark: note 3,6,7
90(Typ.) Remark:note 3,6,8
Change remark of viewing angle=>note 8
note 3,9
Add remark of color chromaticity=> note 3
Change remark of white uniformity=> note 9
3
08/Jan./2001
12
Change packing form
13
Change outline dimension drawing
14
Change timing chart
8
Lamp starting voltage Vs=> (910)(Typ.)
(700)(Typ.)
9
note 10
910(Max.) T=0° C
700(Max.) T=25° C
Brightness YL =>Add 2 mA lamp current spec. (50 nit)
Color chromaticity=>
Wx : 0.31
.0.31
0.03
;
Wy : 0.33
.0.33
0.03
Record of Revision
Version
Revise Date
Page
Content
Rx : 0.57
Gx : 0.30
Bx : 0.15
.0.57
.0.30
.0.15
0.03
;
Ry : 0.32
0.03
;
Gy : 0.56
0.03
;
By : 0.12
10
Add Note 9
12
Add the position of carton label
14
Detail DE timing: Tv Th
.0.32
.0.56
.0.12
0.03
0.03
0.03
SPEC NO. : 413-212-061
PAGE
1/14
:
Contents:
A. Physical specification
B. Electrical specifications
1. Pin assignment
2. Absolute maximum ratings
3. Electrical characteristics
a. Typical operating conditions
b. Display color v. s. input data signals
c. Input signal timing
d. Display position
e. Backlight driving conditions
C. Optical specifications
D. Reliability test items
E. Display quality
P11
P9
P8
P7
P7
P6
P5
P5
P4
P3
P3
…
F. Handling precaution
G. Packing form
P2
P11
P11
P12
Appendix:
Fig.1 LCM outline dimensions ………
Fig.2 Timing chart
………
P13
P14
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
:
2/14
A. Physical specifications
NO.
Item
Specification
1
Display resolution(pixel)
800 (H)
2
Active area(mm)
170.4 (H)
3
Screen size(inch)
8.4 (Diagonal)
4
Pixel pitch(mm)
0.213 (H)
5
Color configuration
R. G. B. Vertical stripe
6
Overall dimension(mm)
203.0 (W)
7
Weight(g)
230
Remark
600 (V)
127.8 (V)
0.213 (V)
142.5 (H)
5.7(D)
Note 1
10
Note 1: Refer to Fig. 1.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
:
PAGE
3/14
B.
Electrical specifications
specifications
B. Electrical
1.Pin assignment
(1).Input signal interface
Pin no
Symbol
Function
1
VCC
+3.3 V power supply
2
VCC
+3.3 V power supply
3
GND
Ground
4
GND
Ground
5
RxIN0-
6
RxIN0+
7
GND
8
RxIN1-
9
RxIN1+
10
GND
11
RxIN2-
12
RxIN2+
13
GND
Ground
14
CKIN-
LVDS receiver signal clock
15
CKIN+
16
GND
17
NC
No Connection
18
NC
No Connection
19
GND
Ground
20
GND
Ground
Etc.
LVDS receiver signal channel 0
Ground
LVDS receiver signal channel 1
Ground
LVDS receiver signal channel 2
Ground
CN1 (20P) connector: HRS DF 19K-20P-1H or compatible
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
:
4/14
(2) LVDS transmitter/receiver signal mapping
Symbol
Function
TxIN0
R0
Red data (LSB)
TxIN1
R1
Red data
TxIN2
R2
Red data
TxIN3
R3
Red data
TxIN4
R4
Red data
TxIN5
R5
Red data (MSB)
TxIN6
G0
Green data (LSB)
TxIN7
G1
Green data
TxIN8
G2
Green data
TxIN9
G3
Green data
TxIN10
G4
Green data
TxIN11
G5
Green data (MSB)
TxIN12
B0
Blue data (LSB)
TxIN13
B1
Blue data
TxIN14
B2
Blue data
TxIN15
B3
Blue data
TxIN16
B4
Blue data
TxIN17
B5
Blue data (MSB)
TxIN18
Hs
Horizontal sync
TxIN19
Vs
Vertical sync
TxIN20
DE
Data enable
TxCLKIN
CLK
Clock
6 bit red display data
6 bit green display data
6 bits blue display data
Dot clock
2. Absolute maximum ratings
Parameter
(GND = 0 V)
Values
Symbol
Unit
Power voltage
VCC
Min.
-0.3
Input signal voltage
VLH
-0.3
VCC+0.3
Operating temperature
Top
0
+60
Storage temperature
TST
-20
+70
Remark
Max.
4
VDC
At 25
VDC
At 25
Note 1
Note 1
Note 1:The relative humidity must not exceed 90% non-condensing at temperatures of 40
or
less. At temperatures greater than 40 , the wet bulb temperature must not exceed 39
. When operate at low temperatures, the brightness of CCFL will drop and the lifetime
of CCFL will be reduced.
Note 2:The unit should not be exposed to corrosive chemicals.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
5/14
:
3. Electrical characteristics
a. Typical operating conditions
Symbol
Min.
Typ.
Max.
Unit
Input voltage
VCC
3.0
3.3
3.6
V
Current
consumption
IA
-
220
-
mArms
IB
-
-
300
mArms
Inrush current
I RUSH
-
-
1500
mApeak
Low voltage
VIL
0
-
0.3 VCC
High voltage
VIH
0.7VCC
-
VCC
VRP
-
-
100
Item
Power
supply
voltage
Internal
logic
Power ripple voltage
Remark
Note 1
Note 2
mVp-p
Note 1:Effective value (mArms) at VCC = 3.3 V/25 .
IA
Black
(0)
64
IB
White
Gray
(7)
64
Black
Vertical stripe line
64 Grayscale
Note 2: Refer to the following power-on condition.
90%
Vcc
10%
Ton=470 s
10%
Sequence of power-on/off and signal-on/off
T3
T4
0ms T1 70msec
Power
T1
T5
Input signal
T2
0
T2 70msec
300msec
300msec
T5
T3
T4
10msec
Apply the lamp voltage within the LCD operating range. When the backlight turns on before
the LCD operation or the LCD turns off before the backlight turns off, the display may
momentarily become abnormal.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
6/14
:
Caution
The above on/off sequence should be applied to avoid abnormal function in the display.
In case of handling:
Make sure to turn off the power when you plug the cable into the input connector or pull the
cable out of the connector.
b. Display color vs. input data signals
Display colors
Basic
colors
Black
Blue
Red
Magenta
Green
Cyan
Yellow
White
Black
Dark
Data signal (0 : Low level, 1: High level)
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
0
0
1
1
0
0
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
1
0
0
1
1
0
0
1
1
0
1
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
Red
grayscale
Bright
Red
Black
Dark
Green
grayscale
Bright
Green
Black
Dark
Blue
grayscale
Bright
Blue
Note: Each basic color can be displayed in 64 gray scales using the 6 bit data signals. By
combining the 18-bit data signals(R, G, B), the 262, 144 colors can be achieved on the
display.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
:
7/14
c. Input signal timing
Timing diagrams of input signal are shown in Fig 2.
(1). Timing characteristics of input signals
DE mode
Item
Clock frequency
Symbol
Fck
Min.
38
Typ.
40
Max.
42
Unit
MHz
Horizontal blanking
Thb1
235
256
500
Clk
Horizontal display period
Thd
-
800
-
Clk
Horizontal sync. period
Th
1035
1056
1300
Clk
Vertical blanking
Tvb1
10
28
150
Th
Vertical display width
Tvd
-
600
-
Th
Vertical sync. period
Tv
610
628
750
Th
Symbol
Min.
Typ.
Max.
-
0.6
Remark
(2). The timing condition of LVDS
Item
The differential level
VID
The common mode input
voltage
VIC
The input setup time
The input hold time
0.1
Unit
V
VID
2
-
tsu1
0.5
-
-
ns
th1
0.5
-
-
ns
VID
VIAP
2.4
VID
2
V
VID = VIAP - VIAM
VIAM
tsu1 th1
An
7 LCK
d. Display position
D( 1,1 )
D( 2,1 )
……
D( X,1 )
……
D( 799,1 )
D( 800,1 )
D( 1,2 )
..
.
D( 2,2 )
……
D( X,2 )
..
.
……
D( 799,2 )
..
.
D( 800,2 )
..
.
D( 1,Y )
..
.
D( 2,Y )
……
……
D( X,Y )
..
.
D( 799,Y )
..
.
D( 800,Y )
..
.
D( 1,599 )
D( 2,599 )
……
D( X,599 )
……
D( 799,599) D( 800,599 )
D( 1,600 )
D( 2,600 )
……
D( X,600 )
……
D( 799,600)
……
……
……
……
D( 800,600)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
:
8/14
e. Backlight driving conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
Remark
Lamp voltage
VL
441
490
539
Vrms
Note 1
Lamp current
IL
3
4.6
-
mArms
Note 1
Power consumption
PL
-
2.25
-
W
Note 2
Lamp starting voltage
VS
-
-
910
-
-
700
Vrms
T=0
T=25
Frequency
FL
50
60
80
KHZ
Note 3
Lamp life time
LL
10000
20000
-
Hr
Note 1, 4
Note 1: T= 25
Note 2: Inverter should be designed with the characteristic of lamp. When you are designing
the inverter, the output voltage of the inverter should comply with the following
conditions.
(1). The area under the positive and negative cycles of the waveform of the lamp
current and lamp voltage should be area symmetric(the symmetric ratio should
be larger than 90%).
(2). There should not be any spikes in the waveform.
(3). The waveform should be sine wave as possible.
(4). Lamp current should not exceed the maximum value within the operating
temperature (It is prohibited to over the maximum lamp current even if operated
in the non-guaranteed temperature). When lamp current over the maximum value
for a long time, it may cause fire. Therefore, it is recommend that the inverter
should have the current limit circuit.
Note 3: Lamp frequency may produce interference with horizontal synchronous frequency and
this may cause line flow on the display. Therefore lamp frequency shall be detached
from the horizontal synchronous frequency and its harmonics as far as possible in
order to avoid interference. In case using the inverter by PWM control, PWM
frequency may interference with frame frequency. We suggest that PWM frequency
is same as frame frequency.
Note 4: Brightness to be decrease to the 50% of the initial value.
Note 5: CN2 connector (backlight): BHSR-02VS-1(JST)
Mating connector: SM02B-BHSS-1-TB (JST)
Pin no.
Symbol
Function
Remark
1
H
CCFL power supply(H.V.)
Cable color: Pink
2
L
CCFL power supply(GND)
Cable color: White
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
9/14
:
C. Optical specifications ( Note 1, Note 2 )
Item
Symbol
Specification
Condition
Unit
Remark
ms
Note 4
Min.
Typ.
Max.
-
20
30
40
50
150
250
-
30
10
40
40
-
-
-
150
-
nit
Note 3,6,7
-
90
nit
Note 3,6,8
-
50
--
nit
Note 3,6,9
0.28
0.31
0.34
0.30
0.33
0.36
Rx
0.54
0.57
0.60
Ry
0.29
0.32
0.35
Gx
0.27
0.30
0.33
Gy
0.53
0.56
0.59
Bx
0.12
0.15
0.18
By
0.09
0.12
0.15
-
-
1.8
Response time
Rising time
Falling time
Tr
Tf
Contrast ratio
CR
=0
=0
Note 3, 5
Viewing angle
Top
Bottom
Left
Right
CR
Color chromaticity(CIE)
White uniformity
Wx
=0
Wy
!
10
=0
YL
Brightness
W
deg. Note 3,10
Note 3
Note 3,11
Note 1: Ambient temperature = 25 .
Note 2: To be measured in dark room after lighting the backlight for 30 minutes.
Note 3: To be measured with the viewing cone of 1 by Topcon luminance meter BM-5A.
Note 4: Definition of response time:
The output signals of BM-7 are measured when the input signals are changed from
“Black” to “White” (falling time) and from “White” to “Black” (rising time), respectively. The
response time interval between the 10% and 90% of amplitudes. Refer to figure as
below.
"
#
"Black"
"White"
"White"
Signal(Relative value)
100%
90%
10%
0%
Tr
Tf
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
:
10/14
Note 5. Definition of contrast ratio:
Contrast ratio is calculated with the following formula.
Contrast ratio (CR)=
Brightness on the “white” state
Brightness on the “black” state
Note 6: Definition of brightness: This shall be measured at center of the screen.
Note 7: Driving conditions for CCFL : IL=4.6 mA,60KHz frequency
Note 8: Driving condition for CCFL : IL=3 mA,60KHz frequency
Note 9: Driving condition for CCFL : IL=2 mA,60KHz frequency
Note 10: Definition of viewing angle:
$
Note 11: Definition of white uniformity:
White uniformity is defined as the following with thirteen measurements (1~9).
%
W
=
Maximum brightness of nine points
Minimum brightness of nine points
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
:
11/14
D. Reliability test items (Note 1)
Test tem
High temperature storage
70
Test Condition
, 240Hrs
Low temperature storage
-20
High temperature & high
humidity operation
40
High temperature operation
60
Low temperature operation
0
Temperature cycling
(non-operation)
-20
Electrostatic discharge
(non-operation)
150 pF,150 ,10kV,1 second, 9 position Note 3
on the panel, 10 times each place
Vibration
(non-operation)
Sweep:1G, 10HZ ~ 500HZ ~ 10HZ /2.5min Note 1, 2, 3
2 hour for each direction X, Y, Z
(6 Hrs in total)
&
Remark
Note 1, 2, 3
, 240Hrs
&
Note 1, 2, 3
, 90%RH, 240Hrs
&
Note 1, 2, 3
(No condensation)
, 240Hrs
&
&
&
Note 1, 2, 3
, 240Hrs
Note 1, 2, 3
~70
Note 1, 2, 3
&
1H, 10mins, 1H, 5cycles
'
Mechanical shock
(non-operation)
50G/11ms, 200G/2ms,
(
X,
(
Y,
(
Z
Note 1, 2, 3
once for each direction
Note 1: Evaluation should be tested after storage at room temperature for one hour.
Note 2: There should be no change which might affect the practical display function when the
display quality test is conducted under normal operating condition.
Note 3: Judgement :
1.Function OK.
2.No serious image quality degradation .
E. Display quality
The display quality of the color TFT-LCD module should be in compliance with the
Unipac’s OQC inspection standard.
F. Handling precaution
The Handling of the TFT-LCD should be in compliance with the Unipac’s handling principle
standard.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
PAGE
:
12/14
G. Packing form :
LCD Module
Anti-Static
Bag
NOTE :
1. Max. Capacity : 30 LCD Modules/Carton.
2. Max. Weight : 10 Kg/Carton.
3. Meas : 600 mm*353mm*210mm.
EPP Cushion
Carton
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
:
13/14
Fig.1 LCM outline dimensions
PAGE
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
SPEC NO. : 413-212-061
invalid
Fig.2 Timing chart
Th
3,Y
1,Y
2,Y
Tv
X,1
X,2
X,3
Thd
Tvd
X,599 X,600
799,Y 800,Y
Invalid
14/14
Thbl
DE
800,Y
RGB
CLK
DE
RGB
X,599 X,600
Fck
invalid
Tvbl
Invalid
:
(1 pixel / clock)
PAGE
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.
UNIPAC OPTOELECTRONICS CORPORATION
TERMS AND CONDITIONS OF SALE
These Terms and Conditions of Sale apply to all items designed and/or made by Unipac
Optoelectronics Corporation ("Unipac"), and Buyer agrees they apply to all such items.
1
ACCEPTANCE OF TERMS. BUYER ACCEPTS THESE TERMS (i) BY WRITTEN
ACCEPTANCE (BY PURCHASE ORDER OR OTHERWISE), OR (ii) BY FAILURE TO
RETURN GOODS SUPPLIED BY UNIPAC WITHIN 5 DAYS OF THEIR DELIVERY.
2
DELIVERY
2.1 Delivery will be made Free Carrier (Incoterms 1990), Unipac's warehouse,
Science-Based Industrial Park, Taiwan to a carrier designated in writing by Buyer, or if
Buyer fails to designate a carrier, to a carrier designated by Unipac.
2.2
Title to the goods and the entire risk will pass to Buyer upon delivery to carrier.
2.3 Shipments are subject to availability. Unipac shall make every reasonable effort
to meet the date(s) quoted or acknowledged; and if Unipac makes such effort, UNIPAC
WILL NOT BE LIABLE FOR ANY DELAYS.
3
TERMS OF PAYMENT
3.1 Unless otherwise stated on Unipac's quotation, all shipments shall be T/T in
advance, by Letter of Credit at Sight, or pursuant to agreed prepayment terms. Unipac
reserves the right to change credit terms at any time in its sole discretion.
3.2 Buyer guarantees prompt payment of all obligations accrued pursuant to purchase
orders issued by Buyer.
4
LIMITED WARRANTY
4.1 Unipac warrants that the goods sold will be free from defects in material and
workmanship and comply with Unipac's applicable published specifications for a period
of sixty (60) days from the date of Unipac's shipment.
THIS AGREEMENTSTATES THE ONLY AND EXCLUSIVE REMEDY FOR ANY AND
ALL CLAIMS MADE AGAINST UNIPAC UNDER ANY AGREEMENT AND/OR WITH
RESPECT TO PANELS, COMPONENTS, SERVICES AND/OR GOODS.
5.5 No action or proceeding may be commenced by either party against the other
(other than to collect money due for goods delivered or services rendered), whether for
breach, indemnification, contribution or otherwise, more than one year after delivery of
the goods to the carrier; and no claim may be brought unless the non-claiming party has
first been given commercially reasonable notice, a full written explanation of all pertinent
details (including copies of all materials), and a good faith opportunity to resolve the
matter.
5.6 BUYER EXPRESSLY AGREES TO THE LIMITATIONS OF ARTICLES 5, 8 AND
9 AND TO THEIR REASONABLENESS.
5.7 The exclusions and limitations of Articles 5, 8 and 9 will survive the termination of
the applicable Agreements, and shall apply notwithstanding any claim of a failure of any
one or more remedies to accomplish their purpose, and THE PARTIES EXPRESSLY
WAIVE AND RELINQUISH ANY CONTRARY RIGHTS UNDER ANY AGREEMENT,
AND/OR LAW, DECISION, CUSTOM OR PRACTICE.
6
SUBSTITUTIONS AND MODIFICATIONS
Unipac may at any time make substitutions for product ordered which do not materially
and adversely affect overall performance with the then current specifications in the
typical and intended use. Unipac reserves the right to halt deliveries and shipments and
alter specifications and prices without notice. Buyer shall verify that the literature and
information is current before purchasing. Other changes to process and/or specifications
by Unipac shall be pursuant to Unipac’ s standard ECN procedures.
7
CANCELLATION
4.2 Goods or parts which have been subject to abuse (including without limitation
repeated or extended exposure to conditions at or near the limits of applicable absolute
ratings) misuse, accident, alteration, neglect, or unauthorized repair or improper
application are not covered by any warranty. No warranty is made with respect to
custom products or goods produced to Buyer's specifications (unless specifically stated
in writing signed by Unipac). Unipac shall not be responsible for defects or claims
caused by acts not performed by Unipac; or by combination of goods with other things.
7.1 This Agreement may not be canceled by Buyer except with written consent by
Unipac and Buyer's payment of reasonable cancellation charges (including but not be
limited to expenses already incurred for labor and material, overhead, commitments
made by Unipac, and a reasonable profit).
4.3 No warranty is made with respect to goods used in devices intended for use in
applications where failure to perform when properly used can reasonably be expected to
result in significant injury (including, without limitation, navigation, aviation, weaponry or
nuclear equipment, or for surgical implant or to support or sustain life) and Buyer agrees
to indemnify, defend, and hold harmless Unipac from all claims, damages and liabilities
arising out of any such uses.
8.1 Unipac will, at its own expense, assist Buyer with technical support and
information in connection with any claim that any parts as shipped by Unipac under this
purchase order infringe any valid, enforceable, unexpired R.O.C. patent, copyright, or
trademark, provided however, that Buyer (i) gives immediate written notice to Unipac, (ii)
permits Unipac to participate and to defend if Unipac requests to do so, and (iii) gives
Unipac all needed information, assistance and authority. However, Unipac will not be
responsible for infringements resulting from anything not entirely manufactured by
Unipac, or from any combination with products, equipment, or materials not furnished by
Unipac. Unipac will have no liability with respect to intellectual property matters arising
out of products made to Buyer's specifications, code, or designs.
4.4 This Article 4 is the only warranty by Unipac with respect to goods and may not be
modified or amended except in writing signed by an authorized officer of Unipac.
4.5 Buyer acknowledges and agrees that it is not relying on any applications,
diagrams or circuits contained in any literature, and Buyer will test all parts and
applications under extended field and laboratory conditions. Notwithstanding any crossreference or any statements of compatibility, functionality, interchangeability, and the
like, the goods may differ from similar goods from other vendors in performance,
function or operation, and in areas not contained in the written specifications, or as to
ranges and conditions outside such specifications; and Buyer agrees that there are no
warranties and that Unipac is not responsible for such things.
4.6 REGARDLESS OF CAUSE OR REASON FOR DAMAGE (WHETHER
ACCIDENT, NEGLIGENCE, OR OTHERWISE) UNIPAC SHALL HAVE NO LIABILITY
(DIRECT, CONSEQUENTIAL OR OTHER) FOR, IN CONNECTION WITH OR ARISING
FROM PROPERTY FURNISHED FOR USE AT OR LEFT AT UNIPAC; and by
delivering or entrusting property to Unipac, Buyer expressly confirms this limitation.
Notwithstanding this limitation, Unipac will replace, or pay the reasonable retooling costs
to replace, masks damaged or destroyed as a result of Unipac's gross negligence or
fault.
4.7 EXCEPT AS PROVIDED ABOVE, UNIPAC MAKES NO WARRANTIES OR
CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY; AND UNIPAC EXPRESSLY
EXCLUDES AND DISCLAIMS ANY WARRANTY OR CONDITION OF NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE
OR APPLICATION.
7.2
8
In no event will Buyer have rights in partially completed goods.
INDEMNIFICATION
8.2 Except as expressly stated in this Article 8 or in another writing signed by an
authorized officer, Unipac makes no representations and/or warranties with respect to
intellectual and/or industrial property and/or with respect to claims of infringement.
8.3 Except as to claims Unipac agrees in writing to defend, BUYER WILL INDEMNIFY,
DEFEND AND HOLD HARMLESS UNIPAC FROM ALL CLAIMS, COSTS, LOSSES,
AND DAMAGES (INCLUDING ATTORNEYS FEES) AGAINST AND/OR ARISING OUT
OF GOODS SOLD AND/OR SHIPPED HEREUNDER.
9
NO CONFIDENTIAL INFORMATION
Unipac shall have no obligation to hold any information in confidence except as
provided in a separate non-disclosure agreement signed by both parties.
10 ENTIRE AGREEMENT
These terms and conditions are the entire agreement between Unipac and Buyer, and
no addition, deletion or modification shall be binding on Unipac unless expressly agreed
to in a writing signed by an officer of Unipac. Buyer is not relying upon any warranty or
representation except for those specifically stated here.
11 APPLICABLE LAW
This Agreement and all performance and disputes arising out of or relating to goods
involved will be governed by the laws of Taiwan, Republic of China, without reference to
conflict of laws principles and excluding the U.N. Convention on Contracts for the
5
LIMITATION OF LIABILITY
International Sale of Goods. Buyer agrees at its sole expense to comply with all
applicable laws in connection with the purchase, use or sale of the goods provided
5.1 Unipac will not be liable for any loss, damage or penalty resulting from causes
beyond its reasonable control, including but not limited to delay by others, force majeure, hereunder.
acts of God, material shortage or labor conditions. In any such event, the date(s) for
12 DISPUTE RESOLUTION
Unipac's performance will be deemed extended for a period equal to any delay resulting.
12.1 Buyer and Unipac shall cooperate and attempt in good faith to resolve any and all
5.2 THE LIABILITY OF UNIPAC ARISING OUT OF THIS AGREEMENT OR ANY
disputes arising out of and/or relating to this Agreement and/or goods furnished
GOODS SOLD WILL BE LIMITED TO REFUND OF THE PURCHASE PRICE OR
pursuant to this Agreement.
(WITH UNIPAC'S PRIOR WRITTEN CONSENT) REPAIR OR REPLACEMENT OF
12.2 Any disputes relating to and/or arising out of any Agreement and/or goods
PURCHASED GOODS (RETURNED TO UNIPAC FREIGHT PRE-PAID); OR IN THE
furnished pursuant to this Agreement that cannot be so resolved will be decided
EVENT OF A FAILURE OR BREACH BY UNIPAC REGARDING DELIVERY, AN
exclusively by binding arbitration. Such arbitration shall take place in Taipei, Taiwan
AMOUNT EQUAL TO THE TOTAL PURCHASE PRICE OF THE GOODS THAT HAVE
pursuant to the Rules for International Arbitrations under the American Arbitration
NOT BEEN DELIVERED DUE TO SUCH FAILURE.
Association.
5.3 Buyer will not return any goods without first obtaining a customer return order
12.3 Notwithstanding anything to the contrary, any party may apply to any court of
number.
competent jurisdiction for interim injunctive relief with respect to irreparable harm which
5.4 AS A SEPARATE LIMITATION, IN NO EVENT WILL UNIPAC BE LIABLE (i) FOR cannot be avoided and/or compensated by such arbitration proceedings, without breach
COSTS OF SUBSTITUTE GOODS, (ii) FOR ANY SPECIAL, CONSEQUENTIAL,
of this Article 12 and without any abridgment of the powers of the arbitrators.
INCIDENTAL, RELIANCE OR INDIRECT DAMAGES, OR (iii) FOR LOSS OF USE,
13 ATTORNEYS' FEES
OPPORTUNITY, MARKET POTENTIAL, GOODWILL AND/OR PROFIT ON ANY
Reasonable attorneys' fees and costs will be awarded to the prevailing party in the
THEORY (CONTRACT, TORT, FROM THIRD PARTY CLAIMS OR OTHERWISE).
event of litigation involving the enforcement or interpretation of this Agreement.
THESE LIMITATIONS SHALL APPLY NOTWITHSTANDING ANY FAILURE OF
ESSENTIAL PURPOSE OR OF ANY FAILURE OR INADEQUACY OF ANY REMEDY.
Unipac Optoelectronics Corp.
No.5, Li-Hsin Road 6 ,
Science-Based Industrial Park,
Hsin-Chu City, Taiwan, R.O.C.
Fax:886-3-5772545
Tel :886-3-5632899
Unipac copyright 2001
All rights reserved ,
copying forbidden.