TI TPS78833DBVR

TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
150-mA LOW-NOISE LDO WITH IN-RUSH
CURRENT CONTROL FOR USB APPLICATION
FEATURES
D 150-mA Low-Dropout Regulator
D Available in 2.5 V, 3.3 V
D Programmable Slew Rate Control
D Output Noise Typically 56 µVRMS
D Only 17 µA Quiescent Current at 150 mA
D 1 µA Quiescent Current in Standby Mode
D Dropout Voltage Typically 150 mV at 150 mA
(TPS78833)
D Over Current Limitation
D –40°C to 125°C Operating Junction
D
Temperature Range
5-Pin SOT-23 (DBV) Package
DBV PACKAGE
(TOP VIEW)
IN
1
GND
2
EN
3
5
4
OUT
DESCRIPTION
The TPS78825 and TPS78833 are very small (SOT-23)
package, low-noise LDOs that regulate the output
voltage to 2.5 V and 3.3 V with input voltage ranging
from 2.7 V to an absolute maximum of 13.5 V. These
devices output 150 mA with a peak current of 350 mA
(typ). The TPS788xx family uses the SR pin to program
the output voltage slew rate to control the in-rush
current. This is specifically used in the USB application
where large load capacitance is present at start-up. The
TPS788xx devices use only 17 µA of quiescent current
and exhibit only 56 µVRMS of output voltage noise using
a 10 µF output capacitor.
The usual PNP pass transistor has been replaced by a
PMOS pass element. Because the PMOS pass element
behaves as a low-value resistor, the dropout voltage is
very low, typically 150 mV at 150 mA of load current, and
is directly proportional to the load current.
The TPS788xx also features a logic-enabled sleep
mode to shut down the regulator, reducing quiescent
current to 1 µA typical at TJ = 25°C.
SR
QUIESCENT CURRENT
vs
FREE-AIR TEMPERATURE
OUTPUT VOLTAGE, ENABLE VOLTAGE
vs
TIME (START-UP)
Enable Voltage – V
25
VCC = 4.3 V
IO = 1 mA
15
– Output Voltage – V
Quiescent Current – µ A
IO = 150 mA
20
10
5
O
0
V
–40 –25 –10 5 20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
5
0
C(SR) = 0.01 µF
3
C(SR) = 0.1 µF
2
VI = 4.3 V
VO = 3.3 V
IO = 150 mA
Co = 10 µF
TJ = 25°C
1
0
0
10 20
30 40 50
60
70 80
90 100
t – Time – ms
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
1
TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
AVAILABLE OPTIONS
TJ
VOLTAGE
PACKAGE
2.5 V
SOT-23
SOT
23
(DBV)
40°C to 125°C
–40°C
3.3 V
† The DBVT indicates tape and reel of 250 parts.
‡ The DBVR indicates tape and reel of 3000 parts.
PART NUMBER
TPS78825DBVT† TPS78825DBVR‡
TPS78833DBVT
SYMBOL
TPS78833DBVR
PGZI
PGTI
functional block diagram
OUT
IN
EN
150 k
Current Limit
/ Thermal
Protection
Vref
GND
SR
Terminal Functions
TERMINAL
NAME
NO.
I/O
I
DESCRIPTION
EN
3
GND
2
Active low enable
IN
1
I
The IN terminal is the input to the device.
OUT
5
O
The OUT terminal is the regulated output of the device.
SR
4
I
The SR terminal is used to control the in-rush current.
Regulator ground
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)§
Input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 13.5 V
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VI + 0.3 V
Voltage on OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C
Operating ambient temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
§ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
BOARD
PACKAGE
RθJC
RθJA
DERATING FACTOR
ABOVE TA = 25°C
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
Low K¶
High K#
DBV
65.8°C/W
259°C/W
3.9 mW/°C
386 mW
212 mW
154 mW
DBV
65.8°C/W
180°C/W
5.6 mW/°C
555 mW
305 mW
222 mW
¶ The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the board.
# The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground
planes and 2 ounce copper traces on top and bottom of the board.
2
www.ti.com
TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
electrical characteristics over recommended operating free-air temperature range EN = 0,
TJ = –40 to 125 °C, VI = VO(typ) + 1 V, IO = 1 mA, Co = 4.7 µF, C(SR) = 0.01 µF (unless otherwise noted)
PARAMETER
VI
IO
Input voltage (see Note 2)
TJ
Operating junction temperature
TEST CONDITIONS
Continuous output current (see Note 3)
MIN
TYP
TPS78825
TPS78833
TJ = 25°C
10 µA< IO < 150 mA, 3.8 V < VI < 10 V
Output voltage
10
V
0
150
mA
125
°C
2.5
2.425
2.575
3.3
3.201
10 µA< IO < 450 mA, TJ = 25°C
Quiescent current (GND current)
28
Load regulation
10 µA< IO < 200 mA, TJ = 25°C
12
Out ut voltage line regulation (∆VO/VO)
Output
(see Note 5)
VO + 1 V < VI ≤ 10 V, TJ = 25°C
VO + 1 V < VI ≤ 10 V
0.04
Output current limit
Standby current
EN = 0 V, 2.7 V < VI < 10 V
High level enable input voltage
2.7 V < VI < 10 V
Low level enable input voltage
2.7 V < VI < 10 V
Input current (EN)
EN = 0
Output noise voltage (TPS78833)
Time, start-up
start u (TPS78833)
f = 1 kHz,
TJ = 25°C,
Co = 10 µF
Dropout voltage (see Note 6)
TPS78833
IO = 150 mA, TJ = 25°C
IO = 150 mA
%/V
µVRMS
56
10
50
ms
300
350
750
mA
1
2
µA
1.7
C(SL) = 0.01 µF,
IO = 150 mA,
TPS78833
µA
mV
0.1
V
–1
Power supply ripple rejection
V
3.399
17
10 µA< IO < 150 mA
BW = 200 Hz to 100 kHz,
IO = 150 mA,
TJ = 25°C,
Co = 10 µF,
C(SR) = 0.47 µF
C(byp) = 0.01 µF
RL = 22 Ω,
C(byp) = 0.1 µF
Co = 10 µF,
TJ = 25°C
C(byp) = 0.47 µF
VO = 0 V (see Note 4)
UNIT
2.7
–40
TJ = 25°C
10 µA< IO < 150 mA, 3.5 V < VI < 10 V
MAX
0.9
V
1
µA
70
dB
150
300
mV
NOTES: 2. To calculate the minimum input voltage for your maximum output current, use the following formula:
VI(min) = VO(max) + VDO (max load)
3. Continuous output current and operating junction temperature are limited by internal protection circuitry, but it is not recommended
that the device operate under conditions beyond those specified in this table for extended periods of time.
4. The minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. The maximum IN voltage is 5.5 V. The maximum
output current is 200 mA.
5. If VO ≤ 2.5 V then VImin = 2.7 V, VImax = 5.5 V:
Line regulation (mV) + ǒ%ńVǓ
V
O
ǒVImax * 2.7 VǓ
100
1000
If VO > 2.5 V then VImin = VO + 1 V, VImax = 5.5 V.
6. IN voltage equals VO(typ) – 100 mV
www.ti.com
3
TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT VOLTAGE
vs
LOAD CURRENT
25
3.2
VCC = 4.3 V
TJ = 25°C
VCC = 4.3 V
VCC = 4.3 V
IO = 150 mA
IO = 1 mA
3.31
VO – Output Voltage – V
3.31
3.315
3.305
3.3
3.295
Quiescent Current – µ A
3.315
VO – Output Voltage – V
QUIESCENT CURRENT
vs
FREE-AIR TEMPERATURE
3.305
3.3
3.295
IO = 150 mA
3.29
3.285
20
IO = 1 mA
15
10
5
3.28
3.29
3.275
3.27
–40 –25 –10 5 20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
3.285
15 30 45 60 75 90 105 120 135 150
IL – Load Current – mA
Hz
400
nV/
IO = 150 mA
IO = 1 mA
200
0
100
VI = 4.3 V
Co = 4.7 µF
C(SR) = 0.47 µF
1k
10 k
f – Frequency – Hz
100 k
2
100
VI = 4.3 V
VO = 3.3 V
IO = 150 mA
Co = 10 µF
BW = 200Hz to 100 kHz
80
40
0.01
0.1
C(sr) – Slew Rate Capacitance – µF
Ripple Rejection – dB
V DO – Dropout Voltage – V
VI = 4.3 V
VO = 3.3 V
Co = 10 µF
C(SR) = 0.47 µF
100
90
80
IO = 1 mA
70
60
IO = 150 mA
50
30
20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
Figure 7
4
IO = 1 mA
0.4
IO = 150 mA
20
10
100
1k
100
100 k
1k
10 k
f – Frequency – Hz
1M
OUTPUT VOLTAGE, ENABLE VOLTAGE
vs
TIME (START-UP)
40
–40 –25 –10 5
0.6
Figure 6
50
0
1
0.8
10
1
RIPPLE REJECTION
vs
FREQUENCY
110
IO = 1 mA
1.2
0
120
100
1.4
0.2
20
0.001
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
IO = 150 mA
1.6
Figure 5
VCC = 3.2 V
150
VI = 4.3 V
Co = 4.7 µF
1.8
60
Figure 4
200
OUTPUT IMPEDANCE
vs
FREQUENCY
ROOT MEAN SQUARED OUTPUT NOISE
vs
SLEW RATE CAPACITANCE
Enable Voltage – V
Output Spectral Noise Density –
300
Figure 3
Z o – Output Impedance – Ω
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
100
–40 –25 –10 5 20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
Figure 2
RMS – Root Mean Squared Output Noise – µ V (RMS)
Figure 1
0
10 k
f – Frequency – Hz
Figure 8
www.ti.com
100 k
1M
V O – Output Voltage – V
0
5
0
3
VI = 4.3 V
VO = 3.3 V
IO = 150 mA
C(SR) = 0.47 µF
Co = 10 µF
TJ = 25°C
2
1
0
0
100 200 300 400 500 600 700 800 900 1000
t – Time – ms
Figure 9
TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
C(SR) = 0.1 µF
2
VI = 4.3 V
VO = 3.3 V
IO = 150 mA
Co = 10 µF
TJ = 25°C
1
0
10 20
30 40 50
60
70 80
90 100
t – Time – ms
0.2 V
dv
=
µs
dt
20
0
–20
5.3
4.3
0
20 40
60 80 100 120 140 160 180 200
Figure 10
100
0
50
0
–50
VI = 4.3 V
VO = 3.3 V
Co = 10 µF
–100
0
20
60 80 100 120 140 160 180 200
40
t – Time – µs
Figure 12
TYPICAL REGIONS OF STABILITY
EQUIVALENT SERIES RESISTANCE (ESR)
vs
OUTPUT CURRENT
100
VI = 4.3 V
VO = 3.3 V
Co = 4.7 µF
Region of Instability
1
Region of Stability
0.1
0.075 A
dI
=
µs
dt
200
Figure 11
TYPICAL REGIONS OF STABILITY
EQUIVALENT SERIES RESISTANCE (ESR)
vs
OUTPUT CURRENT
10
LOAD TRANSIENT RESPONSE
t – Time – µs
ESR – Equivalent Series Resistance – Ω
0
VO = 3.3 V
Co = 10 µF
I O – Output Current – mA
C(SR) = 0.01 µF
3
LINE TRANSIENT RESPONSE
∆ V – Change In
O
Output Voltage – mV
0
V O – Output Voltage – mV
5
ESR – Equivalent Series Resistance – Ω
V
O
– Output Voltage – V
Enable Voltage – V
OUTPUT VOLTAGE, ENABLE VOLTAGE
vs
TIME (START-UP)
V I – Input Voltage – V
TYPICAL CHARACTERISTICS
100
VI = 4.3 V
VO = 3.3 V
Co = 10 µF
Region of Instability
10
1
Region of Stability
0.1
0
60
90
120
150
0
IO – Output Current – mA
60
90
120
IO – Output Current – mA
150
Figure 14
Figure 13
www.ti.com
5
TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
APPLICATION INFORMATION
The TPS788xx family of low-dropout (LDO) regulators has been optimized for use in battery-operated
equipment. It features extremely low dropout voltages, low output noise, low quiescent current (17 µA typically),
and enable inputs to reduce supply currents to 1 µA when the regulator is turned off. A typical application circuit
is shown in Figure 15.
1
VI
IN
SR
OUT
1 µF
4
5
VO
3
0.01 µF
EN
+
GND
4.7 µF
ESR = 0.2 Ω
2
Figure 15. Typical Application Circuit
external capacitor requirements
Although not required, a 0.047-µF or larger ceramic input bypass capacitor, connected between IN and GND
and located close to the TPS788xx, is recommended to improve transient response and noise rejection. A
higher-value electrolytic input capacitor may be necessary if large, fast-rise-time load transients are anticipated
and the device is located several inches from the power source.
Like all low dropout regulators, the TPS788xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance is 4.7 µF. The ESR (equivalent
series resistance) of the capacitor should be between 0.2 Ω and 10 Ω. to ensure stability. Capacitor values larger
than 4.7 µF are acceptable, and allow the use of smaller ESR values. Capacitances less than 4.7 µF are not
recommended because they require careful selection of ESR to ensure stability. Solid tantalum electrolytic,
aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided they meet the requirements
described above. Most of the commercially available 4.7 µF surface-mount solid tantalum capacitors, including
devices from Sprague, Kemet, and Nichico, meet the ESR requirements stated above. Multilayer ceramic
capacitors may have very small equivalent series resistances and may thus require the addition of a low value
series resistor to ensure stability.
CAPACITOR SELECTION
PART NO.
MAX ESR†
SIZE (H × L × W)†
MFR.
VALUE
T494B475K016AS
Kemet
4.7 µF
1.5 Ω
1.9 × 3.5 × 2.8
195D106x0016x2T
Sprague
10 µF
1.5 Ω
1.3 × 7.0 × 2.7
695D106x003562T
Sprague
10 µF
1.3 Ω
2.5 × 7.6 × 2.5
TPSC475K035R0600
AVX
4.7 µF
0.6 Ω
2.6 × 6.0 × 3.2
† Size is in mm. The ESR maximum resistance is in Ohms at 100 kHz and TA = 25°C. Contact the
manufacturer for the minimum ESR values.
6
www.ti.com
TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
APPLICATION INFORMATION
external capacitor requirements (continued)
The external bypass capacitor, used in conjunction with an internal resistor to form a low-pass filter, should be
a low ESR ceramic capacitor. For example, the TPS78833 exhibits only 56 µVRMS of output voltage noise using
a 0.01 µF ceramic bypass capacitor and a 10-µF ceramic output capacitor. Note that the output will start up
slower as the bypass capacitance increases due to the RC time constant at the bypass pin that is created by
the internal 150-kΩ resistor and external capacitor.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than
or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
P
T max * T
A
+ J
D(max)
R
θJA
Where:
TJmax is the maximum allowable junction temperature.
RθJA is the thermal resistance junction-to-ambient for the package, see the dissipation rating table.
TA is the ambient temperature.
The regulator dissipation is calculated using:
P
D
ǒ
Ǔ
+ V *V
I
O
I
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
regulator protection
The TPS788xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might
be appropriate.
The TPS788xx features internal current limiting and thermal protection. During normal operation, the TPS78833
limits output current to approximately 350 mA. When current limiting engages, the output voltage scales back
linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure,
care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device
exceeds approximately 165°C, thermal-protection circuitry shuts it down. Once the device has cooled down to
below approximately 140°C, regulator operation resumes.
www.ti.com
7
TPS78825, TPS78833
SLVS382A – JUNE 2001 – REVISED JULY 2001
MECHANICAL DATA
DBV (R-PDSO-G5)
PLASTIC SMALL-OUTLINE
0,50
0,30
0,95
5
0,20 M
4
1,70
1,50
1
0,15 NOM
3,00
2,60
3
Gage Plane
3,00
2,80
0,25
0°–8°
0,55
0,35
Seating Plane
1,45
0,95
0,05 MIN
0,10
4073253-4/F 10/00
NOTES: A.
B.
C.
D.
8
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC MO-178
www.ti.com
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its products to the specifications applicable at the time of sale in accordance with
TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary
to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except
those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
products or services might be or are used. TI’s publication of information regarding any third party’s products
or services does not constitute TI’s approval, license, warranty or endorsement thereof.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation
or reproduction of this information with alteration voids all warranties provided for an associated TI product or
service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service,
is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2001, Texas Instruments Incorporated