TI RI-I02-114A-01

RI-I02-114A-01,, RI-I02-114B-01
www.ti.com
SCBS820 – DECEMBER 2005
Tag-it™ HF-I STANDARD TRANSPONDER INLAYS
LARGE RECTANGLE
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
ISO/IEC 15693-2, -3; ISO/IEC 18000-3
Compliant
13.56-MHz Operating Frequency
256-Bit User Memory in 8-Bit × 32-Bit Blocks
Application Family Identifier (AFI)
Fast Simultaneous Identification
(Anti-Collision)
Product Authentication
Library
Supply-Chain Management
Asset Management
Ticketing/Stored Value
DESCRIPTION
Texas Instruments Tag-it™ HF-I standard transponder inlays consist of 13.56-MHz high-frequency (HF)
transponders that are compliant with the ISO/IEC 15693 and ISO/IEC 18000-3 global open standards. These
products offer a user-accessible memory of 256 bits, organized in eight blocks, and an optimized command set
available in five different antenna shapes, with frequency offset for integration into paper, PVC, or other
substrates.
SPECIFICATIONS (1)
PART NUMBER
RI-I02-114A-01
Supported standard
RI-I02-114B-01
ISO/IEC 15693-2, -3; ISO/IEC 18000-3
Recommended operating frequency
13.56 MHz
13.86 MHz ± 200 kHz
(includes frequency offset to
compensate further integration into
paper)
14.4 MHz ± 200 kHz
(includes frequency offset to
compensate PVC lamination)
Typical required activation field strength to read (at 25°C)
94 dBµA/m (2)
94 dBµA/m (3)
Typical required activation field strength to write (at 25°C)
dBµA/m (2)
97 dBµA/m (3)
Passive resonance frequency (at 25°C)
Factory-programmed read-only number
Memory (user programmable)
Typical programming cycles (at 25°C)
Data retention time (at 55°C)
Simultaneous identification of tags
Antenna size
Foil width
Foil pitch
Base material
Operating temperature
Storage temperature (single inlay)
Storage temperature (on reel)
(1)
(2)
(3)
97
64 bits
256 bits organized in 8-bit × 32-bit blocks
100,000
>10 years
Up to 50 tags per second (reader/antenna dependent)
45 mm × 76 mm (~1.77 in × ~2.99 in)
48 mm ± 0.5 mm (1.89 in ± 0.02 in)
96 mm +0.1 mm/–0.4 mm (3.78 in)
Substrate: PET (polyethylenetherephtalate); Antenna: aluminum
–25°C to 70°C
–40°C to 85°C (warpage may occur at upper temperature range)
–40°C to 40°C
For highest possible read-out coverage, operate readers at a modulation depth of 20% or higher.
After integration into paper
After PVC lamination
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Tag-it is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005, Texas Instruments Incorporated
RI-I02-114A-01,, RI-I02-114B-01
www.ti.com
SCBS820 – DECEMBER 2005
SPECIFICATIONS (continued)
PART NUMBER
RI-I02-114A-01
RI-I02-114B-01
Single-row tape wound on cardboard reel with 500-mm diameter
Reel outer width: approximately 60 mm (~2.36 in)
Reel inner width: approximately 50 mm (~1.97 in)
Hub diameter: 76.2 mm (3 in)
Delivery
Typical quantity of good units per reel
5,000
DESCRIPTION (CONTINUED)
The Tag-it HF-I standard transponder inlays are manufactured with TI’s patented laser tuning process to provide
consistent read performance. Prior to delivery, the transponders undergo complete functional and parametric
testing, in order to provide the high quality that customers have come to expect from TI.
The Tag-it HF-I standard transponder inlays are well suited for a variety of applications including, but not limited
to, product authentication, library, supply-chain management, asset management, and ticketing/stored value
applications.
SUPPORTED COMMAND SET
REQUEST
REQUEST MODE (1)
REQUEST CODE
INVENTORY
ADDRESSED
NON-ADDRESSED
AFI
OPT. FLAG
–
ü
0/–
ISO 15693 Mandatory and Optional Commands
Inventory
0x01
ü
–
Stay Quiet
0x02
–
ü
–
–
0/–
Read_Single_Block
0x20
–
ü
ü
–
–/1
Write_Single_Block
0x21
–
ü
ü
–
–/1
Lock_Block
0x22
–
ü
ü
–
–/1
(1)
ü = Implemented, – = Not applicable
MEMORY ORGANIZATION
Block
Addr
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
32 bits
Lock Bits
F U
User data
(256 bits)
X
UID Number
(64 bits)
AFI
0x0A
2
F = Factory Lock,
U = User Lock
Submit Documentation Feedback
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2007, Texas Instruments Incorporated