TI TPS40193DRCTG4

TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
4.5-V TO 18-V INPUT 10-PIN SYNCHRONOUS BUCK CONTROLLER WITH POWER GOOD
FEATURES
CONTENTS
1
•
•
•
•
•
•
•
•
•
•
•
•
Input Operating Voltage Range: 4.5 V to 18 V
Up to 20-A Output Currents
Supports Pre-Biased Outputs
0.5% 0.591-V Reference
600 kHz (TPS40192) and 300 kHz (TPS40193)
Switching Frequencies
Three Selectable Thermally Compensated
Short Circuit Protection Levels
Hiccup Restart from Faults
Internal 5-V Regulator
High and Low side FET RDSON Current
Sensing
10-Pin 3 mm × 3 mm SON Package
Internal 4-ms Soft-Start Time
Thermal Shutdown Protection at 145°C
3
Electrical Characteristics
4
Typical Characteristics
6
Terminal Information
9
Application Information
11
Design Example
17
Additional References
27
DESCRIPTION
TPS40192 and TPS40193 are cost-optimized
synchronous buck controllers that operate from 4.5 V
to 18 V input. These controllers implement a
voltage-mode control architecture with the switching
frequency fixed at either 600 kHz (TPS40192) or 300
kHz (TPS40193). The higher switching frequency
facilitates the use of smaller inductor and output
capacitors,
thereby
providing
a
compact
power-supply solution. An adaptive anti-cross
conduction scheme is used to prevent shoot through
current in the power FETs.
APPLICATIONS
•
•
•
•
Device Ratings
Cable Modem CPE
Digital Set Top Box
Graphics/Audio Cards
Entry Level and Mid-Range Servers
SIMPLIFIED APPLICATION DIAGRAM
VIN
VOUT
TPS40192/3
ON/OFF
External Logic
Supply
5V or Less,
or BP5
1
ENABLE
2
FB
3
HDRV 10
SW
9
COMP
BOOT
8
4
VDD
LDRV
7
5
PGD
BP5
6
VOUT
GND
11
UDG−06063
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007, Texas Instruments Incorporated
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
DESCRIPTION (continued)
Short circuit detection is done by sensing the voltage drop across the low-side MOSFET when it is on and
comparing it with a user selected threshold of 100 mV, 200 mV or 280 mV. The threshold is set with a single
external resistor connected from COMP to GND. This resistor is sensed at startup and the selected threshold is
latched. Pulse by pulse limiting (to prevent current runaway) is provided by sensing the voltage across the
high-side MOSFET when it is on and terminating the cycle when the voltage drop rises above a fixed threshold of
550 mV. When the controller senses an output short circuit, both MOSFETs are turned off and a timeout period
is observed before attempting to restart. This provides limited power dissipation in the event of a sustained fault.
ORDERING INFORMATION
TJ
PACKAGE
FREQUENCY (kHz)
TAPE AND REEL
QUANTITY
PART NUMBER
250
TPS40193DRCT
3000
TPS40193DRCR
300
-40°C to 85°C
Plastic 10-Pin SON (DRC)
600
2
Submit Documentation Feedback
250
TPS40192DRCT
3000
TPS40192DRCR
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
DEVICE RATINGS
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
TPS40192/TPS40193
VDD, ENABLE
SW
Input voltage range
–5 to 25
BOOT, HDRV
–0.3 to 30
BOOT-SW, HDRV-SW (differential from BOOT or HDRV to SW)
-0.3 to 6
COMP, FB, BP5, LDRV, PGD
–0.3 to 6
TJ
Operating junction temperature range
–40 to 150
Tstg
Storage temperature
–55 to 150
(1)
UNIT
–0.3 to 20
V
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
MIN
NOM
MAX
UNIT
VVDD
Input voltage
4.5
18
V
TJ
Operating Junction temperature
-40
125
°C
PACKAGE DISSIPATION RATINGS
PACKAGE
DRC
(1)
AIRFLOW (LFM)
RθJA High-K Board (1)
(°C/W)
Power Rating (W)
TA = 25°C
Power Rating (W)
TA = 85°C
0 (Natural Convection)
47.9
2.08
0.835
200
40.5
2.46
0.987
400
38.2
2.61
1.04
Ratings based on JEDEC High Thermal Conductivity (High K) Board. For more information on the test method, see TI Technical Brief
SZZA017.
ELECTROSTATIC DISCHARGE (ESD) PROTECTION
MIN
TYP
Human Body Model (HBM)
2500
Charged Device Model (CDM)
1500
MAX
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
UNIT
V
3
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
ELECTRICAL CHARACTERISTICS
TJ = –40°C to 85°C, VVDD= 12 Vdc, all parameters at zero power dissipation (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
0°C ≤ TJ ≤ 85°C
588
591
594
-40°C ≤ TJ ≤ 85°C
585
591
594
UNIT
REFERENCE
VFB
Feedback voltage range
mV
INPUT SUPPLY
VVDD
Input voltage range
IVDD
Operating current
4.5
18.0
V
VENABLE = 3 V
2.5
4.0
mA
VENABLE = 0.6 V
45
70
μA
ON BOARD REGULATOR
V5VBP
Output voltage
VVDD > 6 V, I5VBP ≤ 10 mA
VDO
Regulator dropout voltage
VVDD - VBP5 , VVDD = 5 V, IBP5 ≤ 25 mA
ISC
Regulator current limit threshold
IBP5
Average current
5.1
5.3
5.5
V
350
550
mV
50
50
mA
OSCILLATOR
fSW
Switching frequency
VRMP
Ramp amplitude (1)
TPS40193
240
300
360
TPS40192
500
600
700
1
kHz
V
PWM
DMAX
tON(min)
tDEAD
Maximum duty cycle (1)
Minimum controlled pulse
85%
(1)
110
Output driver dead time
HDRV off to LDRV on
50
LDRV off to HDRV on
25
ns
SOFT-START
tSS
Soft-start time
tSSDLY
Soft-start delay time
3
4
2
tREG
Time to regulation
6
6
ms
ERROR AMPLIFIER
GBWP
Gain bandwidth product (1)
AOL
DC gain (1)
IIB
Input bias current (current out of FB
pin)
IEAOP
Output source current
VFB = 0 V
1
IEAOM
Output sink current
VFB = 2 V
1
7
10
MHz
60
dB
100
nA
mA
SHORT CIRCUIT PROTECTION
tPSS(min)
Minimum pulse during short circuit (1)
tBLNK
Blanking time (1)
tOFF
Off-time between restart attempts
250
60
VILIMH
(1)
4
Short circuit comparator threshold
voltage
Short circuit threshold voltage on
high-side MOSFET
120
30
50
160
200
240
RCOMP(GND) = 4 kΩ, TJ = 25°C
80
100
120
RCOMP(GND) = 12 kΩ, TJ = 25°C
228
280
342
TJ = 25°C
400
550
650
RCOMP(GND) = OPEN, TJ = 25°C
VILIM
90
ns
ms
mV
Ensured by design. Not production tested.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
ELECTRICAL CHARACTERISTICS (continued)
TJ = –40°C to 85°C, VVDD= 12 Vdc, all parameters at zero power dissipation (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
OUTPUT DRIVERS
RHDHI
High-side driver pull-up resistance
VBOOT - VSW = 4.5 V, IHDRV = -100 mA
3
6
RHDLO
High-side driver pull-down resistance
VBOOT - VSW = 4.5 V, IHDRV = 100 mA
1.5
3.0
RLDHI
Low-side driver pull-up resistance
ILDRV = -100 mA
2.5
5.0
RLDLO
Low-side driver pull-down resistance
ILDRV = 100 mA
0.8
1.5
tHRISE
High-side driver rise time (2)
15
35
10
25
15
35
10
25
(2)
tHFALL
High-side driver fall time
tLRISE
Low-side driver rise time (2)
tLFALL
Low-side driver fall time (2)
CLOAD = 1 nF
Ω
ns
UVLO
VUVLO
Turn-on voltage
3.9
4.2
4.4
V
UVLOHYST
Hysteresis
700
800
900
mV
1.9
3.0
SHUTDOWN
VIH
High-level input voltage, ENABLE
VIL
Low-level input votlage, ENABLE
0.6
V
POWER GOOD
VOV
Feedback voltage limit for powergood
650
VUV
Feedback voltage limit for powergood
525
VPG_HYST
Powergood hysteresis voltage at FB pin
RPGD
Pulldown resistance of PGD pin
VFB = 0 V
7
50
Ω
IPDGLK
Leakage current
VFB = 0 V
7
12
μA
0.8
1.2
V
mV
30
BOOT DIODE
VDFWD
Bootstrap diode forward voltage
IBOOT = 5 mA
0.5
THERMAL SHUTDOWN
TJSD
Junction shutdown temperature (2)
TJSDH
Hysteresis (2)
(2)
145
20
°C
Ensured by design. Not production tested.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
5
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS
RELATIVE REFERENCE FEEDBACK VOLTAGE
vs
JUNCTION TEMPERATURE
RELATIVE OSCILLATOR FREQUENCY CHANGE
vs
JUNCTION TEMPERATURE
0.5
fSW − Relative Oscillator Frequency Change − %
VFB− Relative Reverefnce Voltage Change − %
0.50
0.00
−0.05
−0.10
−0.15
−0.20
−0.25
−0.30
−0.35
−0.40
−0.45
0.0
−0.5
−1.0
−1.5
−2.0
−2.5
−3.0
−3.5
−4.0
−4.5
−40 −25 −10
−0.50
−40 −25 −10 5 20 35 50 65 80 95 110 125
TJ − Junction Temperature − °C
5
20
35
50
65
80
95 110 125
TJ − Junction Temperature − °C
Figure 1.
Figure 2.
SHUTDOWN INPUT CURRENT
vs
JUNCTION TEMPERATURE
ENABLE THRESHOLD VOLTAGE
vs
JUNCTION TEMPERATURE
2.5
60
VENABLE − Enable Threshold Voltage − V
VENABLE< 0.6 V
IVDD − Shutdown Current − µA
50
40
30
20
10
0
−40 −25 −10
5
20
35
50
65
80
95 110 125
TJ − Junction Temperature − °C
2.0
Turn On
1.5
1.0
Turn Off
0.5
0
−40 −25 −10
Figure 3.
6
5
20
35
50
65
80
95 110 125
TJ − Junction Temperature − °C
Figure 4.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS (continued)
SOFT START TIME
vs
JUNCTION TEMPERATURE
LOW-SIDE MOSFET CURRENT LIMIT THRESHOLD
vs
JUNCTION TEMPERATURE
4.05
400
350
VILIM − Current Limit Threshold − mV
tSS − Soft start Time − ms
4.00
3.95
3.90
3.85
3.80
3.75
−40 −25 −10 5
20
35
50
65
80
300
RCOMP = 12 kΩ
250
200
100
RCOMP = 4 kΩ
50
0
−40 −25 −10 5
95 110 125
TJ − Junction Temperature − °C
20
35
50
65
80
95 110 125
TJ − Junction Temperature − °C
Figure 5.
Figure 6.
HIGH-SIDE MOSFET CURRENT LIMIT THRESHOLD
vs
JUNCTION TEMPERATURE
TOTAL TIME TO REGULATION
vs
JUNCTION TEMPERATURE
800
6.3
6.1
700
5.9
600
tREG − Regulation Time − ms
VILIMH − Current Limit Threshold − mV
RCOMP = OPEN
150
500
400
300
200
100
5.7
5.5
5.5
5.3
5.1
4.9
4.7
0
−40 −25 −10 5
20
35
50
65
80
TJ − Junction Temperature − °C
95 110 125
4.4
−40 −25 −10
5
20
35
50
65
80
95 110 125
TJ − Junction Temperature − °C
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
7
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS (continued)
POWERGOOD THRESHOLD VOLTAGE
vs
JUNCTION TEMPERATURE
SHUTDOWN CURRENT
vs
INPUT VOLTAGE
100
VENABLE < 0.6 V
Overvoltage
90
660
80
640
IVDD − Supply Current − µA
VOV, VUV − Powergood Threshold Voltage − mV
680
620
600
580
560
540
Undervoltage
70
60
50
40
30
20
520
10
500
−40 −25 −10
0
5
20
35
50
65
80
4
95 110 125
6
8
10
12
14
16
18
VVDD − Input Voltage − V
TJ − Junction Temperature − °C
Figure 9.
Figure 10.
RELATIVE OVERCURRENT TRIP POINT
vs
FREEWHEEL TIME
IOC - Relative Overcurrent Trip Point - A
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0.4
0.6
0.8
1.0
1.2
1-D - Freewheel Time - ms
1.4
1.6
Figure 11.
8
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
DEVICE INFORMATION
Table 1. TERMINAL FUNCTIONS
TERMINAL
NAME
NO.
BOOT
8
I/O
DESCRIPTION
I
Gate drive voltage for the high-side N-channel MOSFET. A capacitor 100 nF typical must be connected
between this pin and SW.
BP5
6
O
Output bypass for the internal regulator. Connect at least 1μF capacitor from this pin to GND. Larger
capacitors, up to 4.7μF will improve noise performance when using a low side FET with a gate charge of
25nC or greater. Low power, low noise loads may be connected here if desired. The sum of the external
load and the gate drive requirements must not exceed 50 mA. This regulator is turned off when ENABLE is
pulled low.
COMP
3
O
Output of the error amplifier.
ENABLE
1
I
Logic level input which starts or stops the controller from an external user command. A high-level turns the
controller on. A weak internal pull-up holds this pin high so that the pin may be left floating if this function is
not used.
FB
2
I
Inverting input to the error amplifier. In normal operation the voltage on this pin is equal to the internal
reference voltage (591 mV typical)
GND
(11)
-
Thermal pad ground connection. Common reference for the device. Connect to the system GND.
HDRV
10
O
Bootstrapped output for driving the gate of the high side N channel FET.
LDRV
7
O
Output to the rectifier MOSFET gate
PGD
5
O
Open drain power good output
SW
9
I
Sense line for the adaptive anti-cross conduction circuitry. Serves as common connection for the flying high
side MOSFET driver
VDD
4
I
Power input to the controller
DRC PACKAGE
(TOP VIEW)
PGD
5
VDD COMP
4
3
FB ENABLE
2
1
9
10
SW
HDRV
TPS40192
TPS40193
6
BP5
7
8
LDRV BOOT
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
9
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
VDD
SC
+
OCL
FAULT
Fault
Controller
CLK
ENABLE
SD
1
+
OCH
SD
UVLO
Soft Start
Ramp
Generator
VDD - 0.5 V
VDD
BP5
5V
Regulator
4
6
4.2 V
+
5V
UVLO
CLK
COMP
Oscillator
3
FAULT
UVLO
591 mV
FB
2
SS
+
+
Error
Amplifier
GND PP
8
SD
5V
PWM Logic
and
Anti-Cross
Conduction
10 HDRV
5V
UVLO FAULT
+
9
SW
7
LDRV
SC Threshold Latch
FB
Short Circuit
Threshold
Selector
SD
SS
Powergood
Control
ENABLE
5
PGD
750 kW
SC: -110 mV, -200 mV, or -280 mV
UDG-06064
10
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
APPLICATION INFORMATION
Introduction
The TPS40192 and TPS40193 are cost optimized controllers providing all the necessary features to construct a
high performance DC/DC converter while keeping costs to a minimum. Support for pre-biased outputs eliminates
concerns about damaging sensitive loads during startup. Strong gate drivers for the high side and rectifier
N-channel MOSFETs decrease switching losses for increased efficiency. Adaptive gate drive timing prevents
shoot through and minimizes body diode conduction in the rectifier MOSFET, also increasing efficiency.
Selectable short circuit protection thresholds and hiccup recovery from a short circuit increase design flexibility
and minimize power dissipation in the event of a prolonged output fault. A dedicated enable pin (ENABLE) allows
the converter to be placed in a very low quiescent current shutdown mode. Internally fixed switching frequency
and soft-start time reduce external component count, simplifying design and layout, as well as reducing footprint
and cost. The 3 mm × 3 mm package size also contributes to a reduced overall converter footprint.
Voltage Reference
The band gap cell is designed with a trimmed 591 mV output. The 0.5% tolerance on the reference voltage
allows the user to design a very accurate power-supply.
Oscillator
The TPS40192 has a fixed internal switching frequency of 600 kHz while the TPS40193 operates at 300 kHz.
UVLO
When the input voltage is below the UVLO threshold, the device holds all gate drive outputs in the low (OFF)
state. When the input rises above the UVLO threshold, and the ENABLE pin is above the turn ON threshold, the
oscillator begins to operate and the start-up sequence is allowed to begin. The UVLO level is internally fixed at
4.2 V.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
11
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Enable Functionality
The TPS40192 and TPS40193 have a dedicated ENABLE pin. This simplifies user level interface design since
no multiplexed functions exist. Another benefit is a true low power shutdown mode of operation. When the
ENABLE pin is pulled to GND, all unnecessary functions, including the BP5 regulator, are turned off, reducing the
device IDD current to 45-uA. A functionally equivalent circuit of the enable circuitry shown in Figure 12.
VDD
4
200 kΩ
1.5 MΩ
1 kΩ
ENABLE
1
To
Enable
Chip
200 Ω
1 kΩ
300 kΩ
GND
5
UDG−05061
Figure 12. TPS40192 ENABLE Pin Internal Circuitry
If the ENABLE pin is left floating, the chip starts automatically. The pin must be pulled to less than 600 mV to
guarantee that the TPS40192/3 is in shutdown mode. Note that the ENABLE pin is relatively high impedance. In
some situations, there could be enough noise nearby to cause the ENABLE pin to swing below the 600 mV
threshold and give erroneous shutdown commands to the rest of the device. There are two solutions to this
problem should it arise.
1. Place a capacitor from ENABLE to GND. A side effect of this is to delay the start of the converter while the
capacitor charges past the enable threshold
2. Place a resistor from VDD to ENABLE. This causes more current to flow in the shutdown mode, but does not
delay converter startup. If a resistor is used, the total current into the ENABLE pin should be limited to no
more than 500 μA.
12
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Startup Sequence and Timing
The TPS40192/3 startup sequence is as follows. After input power is applied, the 5-V onboard regulator comes
up. Once this regulator comes up, the device goes through a period where it samples the impedance at the
COMP pin and determines the short circuit protection threshold voltage, by placing 400 mV on the COMP pin for
approximately 1 ms. During this time, the current is measured and compared against internal thresholds to select
the short circuit protection threshold. After this, the COMP pin is brought low for 1 ms. This ensures that the
feedback loop is preconditioned at startup and no sudden output rise occurs at the output of the converter when
the converter is allowed to start switching. After these initial two milliseconds, the internal soft-start circuitry is
engaged and the converter is allowed to start. See Figure 13.
ENABLE
COMP
VOUT
Soft Start Time (4 ms)
SC Threshold
Configured
(1 ms)
Compensation
Network Zeroed
(1 ms)
UDG−06062
Figure 13. Startup Sequence
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
13
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Selecting the Short Circuit Current
A short circuit in the TPS40192/3 is detected by sensing the voltage drop across the low-side FET when it is on,
and across the high-side FET when it is on. If the voltage drop across either FET exceeds the short circuit
threshold in any given switching cycle, a counter increments one count. If the voltage across the high-side FET
was higher that the short circuit threshold, that FET is turned off early. If the voltage drop across either FET does
not exceed the short circuit threshold during a cycle, the counter is decremented for that cycle. If the counter fills
up (a count of 7) a fault condition is declared and the drivers turn off both MOSFETs. After a timeout of
approximately 50 ms, the controller attempts to restart. If a short circuit is still present at the output, the current
quickly ramps up to the short circuit threshold and another fault condition is declared and the process of waiting
for the 50 ms an attempting to restart repeats. The low side threshold will increase as the low side on time
decreases due to blanking time and comparator response time. See Figure 11 for changes in the threshold as
the low side FET conduction time decreases.
The TPS40192/3 provides three selectable short circuit protection thresholds for the low side FET: 100 mV,
200 mV and 280 mV. The particular threshold is selected by connecting a resistor from COMP to GND. Table 2
shows the short circuit thresholds for corresponding resistors from COMP to GND. When designing the
compensation for the feedback loop, remember that a low impedance compensation network combined with a
long network time constant can cause the short circuit threshold setting to not be as expected. The time constant
and impedance of the network connected from COMP to FB should be as in Equation 1 to guarantee no
interaction with the short circuit threshold setting.
0.4 V e ǒR1*tC1Ǔ t 10 mA
R1
(1)
where
•
•
t is 1 ms, the sampling time of the short circuit threshold setting circuit
R1 and C1 are the values of the components in Figure 14
C2
VOUT
RCOMP
C1
R1
2
3
FB
COMP
TPS40192/3
UDG−06061
Figure 14. Short Circuit Threshold Feedback Network
14
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Table 2. Short Circuit Threshold Voltage Selection
COMPARATOR RESISTANCE
RCOMP (kΩ)
CURRENT LIMIT THRESHOLD
VOLTAGE (mV)
VILIM(V)
12 ±10%
280
Open
200
4 ±10%
100
The range of short circuit current thresholds that can be expected is shown in Equation 2 and Equation 3.
V ILIM(max)
I SCP(max) +
RDS(on)min
I SCP(min) +
(2)
V ILIM(min)
RDS(on)max
(3)
where
•
•
•
ISCP is the short circuit current
VILIM is the short circuit threshold for the low-side MOSFET
RDS(on) is the channel resistance of the low-side MOSFET
Note that due to blanking time considerations, overcurrent threshold accuracy may fall off for duty cycle greater
than 75% with the TPS40192, or 88% with the TPS40193. The reason for this is that the over current comparator
will have only a very short time to sample the SW pin voltage under these conditions and may not have time to
respond to voltages very near the threshold.
The short circuit protection threshold for the high-side MOSFET is fixed at 550 mV typical, 400 mV minimum.
This threshold is in place to provide a maximum current output using pulse by pulse current limit in the case of a
fault. The pulse will be terminated when the voltage drop acros the high side FET exceeds the short circuit
threshold. The maximum amount of current that can be guaranteed to be sourced from a converter can be found
by Equation 4.
V ILIM(min)
I OUT(max) +
RDS(on)max
(4)
where
•
•
•
IOUT(max) is the maximum current that the converter is guaranteed to source
VILIMH(min) is the short circuit threshold for the high-side MOSFET (400 mV)
RDS(on)max is the maximum resistance of the high-side MOSFET
If the required current from the converter is greater than the calculated IOUT(max) , a lower resistance high-side
MOSFET must be chosen. Both the high side and low side thresholds use temperature compensation to
approximate the change in resistance for a typical power MOSFET. This will help couneract shifts in overcurrent
thresholds as temperature increases. For this to be effective, the MOSFETs and the IC must be well coupled
thermally.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
15
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
5-V Regulator
These devices have an on board 5-V regulator that allows the parts to operate from a single voltage feed. No
separate 5-V feed to the part is required. This regulator needs to have a minimum of 1-μF of capacitance on the
BP5 pin to guarantee stability. A ceramic capacitor is suggested for this purpose.
This regulator can also be used to supply power to nearby circuitry, eliminating the need for a separate LDO in
some cases. If this pin is used for external loads, be aware that this is the power supply for the internals of the
TPS40192/3. While efforts have been made to reduce sensitivity, any noise induced on this line has an adverse
effect on the overall performance of the internal circuitry and shows up as increased pulse jitter, or skewed
reference voltage. Also, when the device is disabled by pulling the EN pin low, this regulator is turned off and will
not be available to supply power.
The amount of power available from this pin varies with the size of the power MOSFETs that the drivers must
operate. Larger MOSFETs require more gate drive current and reduce the amount of power available on this pin
for other tasks. The total current that can be drwan from this pin by both the gate drive and external loads cannot
exceed 50mA. The IC itself will use up to 4mA from the regulator and the total gate drive current can be found
from Equation 5.
For regulator stability, a 1-μF capacitor is required to be connected from BP5 to GND. In some applications using
higher gate charge MOSFETs, a larger capacitor is required for noise suppression. For a total gate charge of
both the high and low side MOSFETs greater than 20 nC, a 2.2-μF or larger capacitor is recommended.
I G + f SW
ǒQG (high) ) QG (low)Ǔ
(5)
where
•
•
•
•
16
IG is the required gate drive current
fSW is the switching frequency (600 kHz for TPS40192, and 300 kHz for TPS40193)
QG(high) is the gate charge requirement for the high-side FET when VGS=5 V
QG(low) is the gate charge requirement for the low-side FET when VGS=5 V
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Pre-Bias Startup
The TPS40192/3 contains a unique circuit to prevent current from being pulled from the output during startup in
the condition the output is pre-biased. When the soft-start commands a voltage higher than the pre-bias level
(internal soft-start becomes greater than feedback voltage [VFB]), the controller slowly activates synchronous
rectification by starting the first LDRV pulses with a narrow on-time. It then increments that on-time on a
cycle-by-cycle basis until it coincides with the time dictated by (1-D), where D is the duty cycle of the converter.
This scheme prevents the initial sinking of the pre-bias output, and ensures that the out voltage (VOUT) starts and
ramps up smoothly into regulation and the control loop is given time to transition from pre-biased startup to
normal mode operation with minimal disturbance to the output voltage. The amount of time from the start of
switching until the low-side MOSFET is turned on for the full (1-D) interval is defined by 32 clock cycles.
Drivers
The drivers for the external HDRV and LDRV MOSFETs are capable of driving a gate-to-source voltage of 5 V.
The LDRV driver switches between VDD and GND, while HDRV driver is referenced to SW and switches
between BOOT and SW. The drivers have non-overlapping timing that is governed by an adaptive delay circuit to
minimize body diode conduction in the synchronous rectifier. The drivers are capable of driving MOSFETS that
are appropriate for a 15-A (TPS40192) or 20A (TPS40193) converter.
Power Good
The TPS40192/3 provides an indication that output power is good for the converter. This is an open drain signal
and pulls low when any condition exists that would indicate that the output of the supply might be out of
regulation. These conditions include:
• VFB is more than ±10% from nominal
• soft-start is active
• an undervoltage condition exists for the device
• a short circuit condition has been detected
• die temperature is over (145°C)
NOTE:
When there is no power to the device, PGOOD is not able to pull close to GND if an
auxiliary supply is used for the power good indication. In this case, a built in resistor
connected from drain to gate on the PGOOD pull down device makes the PGOOD pin
look approximately like a diode to GND.
Thermal Shutdown
If the junction temperature of the device reaches the thermal shutdown limit of 145°C, the PWM and the oscillator
are turned off and HDRV and LDRV are driven low, turning off both FETs. When the junction cools to the
required level (125°C nominal), the PWM inititates soft start as during a normal power up cycle.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
17
TPS40192, TPS40193
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
www.ti.com
Layout Recommendations and Sample Layout
Layout Recommendations:
• PowerPad™ is the device’s(U1) only GND connection. PowerPad™ must be connected to ground.
• PowerPad™ should be directly connected to SYNC FET (Q3) source with short, wide trace.
• Locate 3-5 vias in PowerPad™ land to remove heat from the device.
• Connect input capacitors (C7 & C9) and output capacitors (C8 & C10) grounds directly to SYNC FET (Q3)
source with wide copper trace or solid power ground island.
• Locate input capacitors (C7 & C9), MOSFETs (Q2 & Q3), inductor (L1) and output capacitor (C8 & C10) over
power ground island.
• Use short, wide traces for LDRV and HDRV MOSFET connections.
• Route SW trace near HDRV trace.
• Route GND trace near LDRV trace.
• Use separate analog ground island under feedback components (C1, C2, C3, R5, R6, R7, R8 & R10).
• Connect ground islands at PowerPad™ with 10-mil wide trace opposite SYNC FET (Q2) source connection.
Sample Layout:
Figure 15. TPS40192/3 Sample Layout - Component Placement and Top Side Copper
Figure 16. TPS40192/3 Sample Layout - Bottom Side Copper (X-Ray view from Top)
18
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
DESIGN EXAMPLE
Introduction
This example illustrates the design process and component selection for a 12 V to 1.8 V point-of-load
synchronous buck regulator using the TPS40192. A definition of symbols used can be found in Table 8 of this
datasheet.
Table 3. Design Example Electrical Characteristics
PARAMETER
TEST CONDITION
MIN
NOM
8
MAX
VIN
Input voltage
VIN(ripple
Input ripple
IOUT = 10 A
Output voltage
0 A ≤ IOUT ≤ 10 A
Line regulation
8.0 V ≤ VIN ≤ 14 V
0.5%
Load regulation
0 A ≤ IOUT ≤ 10 A
0.5%
VRIPPLE
Output ripple
IOUT = 10 A
VOVER
Output overshoot
3 A ≤ IOUT ≤ 7 A
VUNDER
Output undershoot
IOUT
Output current
ISCP
Short circuit current trip point
η
Efficiency
fSW
Switching frequency
)
VOUT
0.6
1.764
UNIT
14
1.800
V
1.836
36
50
mV
50
0
10
VIN =12 V, IOUT = 5 A
A
90%
600
kHz
Size
The list of materials for this application is shown Table 7. The efficiency, line and load regulation from boards
built using this design are shown in Figure 17 and Table 3. Gerber Files and additional application information
are available from the factory.
Figure 17. TPS40192 Sample Schematic
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
19
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Design Procedure
Selecting the Switching Frequency
For this design the TPS40192, with fSW = 600 kHz, is selected to reduce inductor and capacitor sizes.
Inductor Selection
The inductor is typically sized for approximately 30% peak-to-peak ripple current (IRIPPLE). Given this target ripple
current, the required inductor size can be calculated by Equation 6.
V IN(max) * V OUT
VOUT
1
L[
0.3 I OUT
V IN(max) f SW
(6)
Solving this for
•
•
•
•
VIN(max) = 14 V
VOUT = 1.8 V
IOUT = 10A
fSW = 600 kHz
an inductor value of 0.87 μH is obtained.
A standard value of 1.0 μH is selected. Solving for IRIPPLE with 1.0 μH results in 2.6-A peak-to-peak ripple.
The RMS current through the inductor is approximated by Equation 7.
I L(rms) +
Ǹǒ
2
2
I L(avg)Ǔ ) 1 ǒI RIPPLEǓ +
12
Ǹǒ
2
I OUTǓ ) 1 ǒI RIPPLEǓ
12
2
(7)
Using Equation 7, the maximum RMS current in the inductor is approximately 10.03 A
20
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Output Capacitor Selection (C8)
The selection of the output capacitor is typically driven by the output transient response. The Equation 8 and
Equation 9 overestimate the voltage deviation to account for delays in the loop bandwidth and can be used to
determine the required output capacitance.
2
I
V OVER t TRAN
COUT
V UNDER t
ǒITRANǓ L
I TRAN L
+
VOUT
V OUT C OUT
I
DT + TRAN
COUT
I TRAN
COUT
DT +
I TRAN
COUT
I TRAN L
+
V IN * V OUT
ǒV
(8)
ǒITRANǓ
IN *
2
L
VOUTǓ
COUT
(9)
If
•
•
VIN(min) > 2 × VOUT, use overshoot to calculate minimum output capacitance.
VIN(min) < 2 × VOUT, use undershoot to calculate minimum output capacitance.
C OUT(min) +
ǒITRAN(max)Ǔ
V OUT
2
L
V OVER
(10)
Based on a 4-A load transient with a maximum 50 mV overshoot at 8.0 V input, calculate a minimum 178-μF
output capacitance.
With a minimum capacitance, the maximum allowable ESR is determined by the maximum ripple voltage and is
approximated by Equation 11.
ESR MAX t
VRIPPLE(tot) * VRIPPLE(cap)
C OUT
V RIPPLE(tot) *
+
ǒ
Ǔ
I RIPPLE
C OUT f SW
I RIPPLE
(11)
Based on 178 μF of capacitance, 2.6-A ripple current, 600-kHz switching frequency and 36-mV ripple voltage,
calculate a capacitive ripple of 24.3 mV and a maximum ESR of 4.4 mΩ.
Two 1206 100-μF, 6.3-V X5R ceramic capacitors are selected to provide more than 178-μF of minimum
capacitance and less than 4.4 mΩ of ESR (2.5 mΩ each).
Peak Current Rating of the Inductor
With output capacitance, it is possible to calculate the charge current during start-up and determine the minimum
saturation current rating for the inductor. The start-up charging current is approximated by Equation 12.
V
COUT
I CHARGE + OUT
T SS
(12)
Using the TPS40192's minimum soft-start time of 3.0 ms, COUT = 240 μF and VOUT = 1.8 V, ICHARGE = 144 mA.
I L(peak) + I OUT(max) ) 1 I RIPPLE ) I CHARGE
2
(13)
Table 4. Inductor Requirements
PARAMETER
Inductance
SYMBOL
VALUE
UNITS
μH
L
1.0
RMS current (thermal rating)
IL(rms)
10.03
Peak current (saturation rating)
IL(peak)
11.3
A
A PG0083.102 1.0-μH is selected for its small size, low DCR (6.6 mΩ) and high current handling capability (12 A
thermal, 17 A saturation)
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
21
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Input Capacitor Selection (C7)
The input voltage ripple is divided between capacitance and ESR. For this design VRIPPLE(cap) = 400 mV and
VRIPPLE(ESR) = 200 mV. The minimum capacitance and maximum ESR are estimated by Equation 14.
I LOAD VOUT
C IN(min) +
VRIPPLE(cap) VIN f SW
(14)
ESR MAX +
VRIPPLE(esr)
I LOAD ) 1 I RIPPLE
2
(15)
For this design CIN > 9.375 μF and ESR < 17.7 mΩ . The RMS current in the input capacitors is estimated by
Equation 16.
ǒ
Ǔ ǸVVOUT * VOUTV
I RMS(Cin) + I IN(rms) * I IN(avg) + I OUT ) 1 I RIPPLE
12
IN
I OUT
IN
(16)
For this design VIN = 14 V, VOUT = 1.8 V, IOUT=10 A and IRIPPLE = 2.6 A calculate an RMS of 2.37 A, so the total
of our input capacitors must support 2.37 A of RMS ripple current.
Two 1210 10-μF 25V X5R ceramic capacitors with about 2 mΩ ESR and a 2-ARMS current rating are selected.
Higher voltage capacitors are selected to minimize capacitance loss at the DC bias voltage to ensure the
capacitors have sufficient capacitance at the working voltage.
22
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
MOSFET Switch Selection (Q1, Q2)
The switching losses for the high-side FET are estimated by Equation 17.
Q GD1
P G1_SW + 1 VIN I OUT T SW f SW + 1 VIN I OUT
2
2
VDD*V TH
RDRV
f SW
(17)
For this design switching losses will be highest at high-line Designing for 1 W of total losses in each MOSFETS
and 60% of the total high-side FET losses in switching losses, we can estimate our maximum gate-drain charge
for the design by using Equation 18.
PG1SW
VDD * V T
1
Q GD1 t
VIN I OUT
RDRV
f SW
(18)
For a 2-V gate threshold MOSFET, the TPS40192's 5-V gate drive, and the TPS40192's 2.5-Ω drive resistance,
we estimate a maximum gate-to-drain charge of 8.5 nC. The switching losses of the synchronous rectifier are
lower than the switching losses of the main FET because the voltage across the FET at the point of switching is
reduced to the forward voltage drop across the body diode of the SR FET and are estimated by using
Equation 19.
The conduction losses in the main FET are estimated by the RMS current through the FET times its RDS(on).
2
VOUT
1 I
P G1COM + I OUT
R DS(on) D + I L(rms) RDS(on)Q1
RIPPLE
12
V IN
(19)
ǒ
Ǔ
Estimating about 40% of total MOSFET losses to be high-side conduction losses, the maximum RDS(on) of the
high-side FET can be estimated by using Equation 20.
P Q1C(on)
R DS(on)Q1 +
2
V OUT
I L(rms)
VIN
(20)
ǒ
Ǔ
For this design with IL_RMS = 11.22 ARMS and 8 V to 1.8 V design, calculate RDS(on)Q1 < 17.3 mΩ for our main
switching FET.
Estimating 80% of total low-side MOSFET losses in conduction losses, repeat the calculation for the
synchronous rectifier, whose losses are dominated by the conduction losses. Calculate the maximum RDS(on) of
the synchronous rectifier by Equation 21.
PQ2C(on)
R DS(on)Q2 +
2
V
I L(rms)
1 * OUT
V IN
ǒ
Ǔ
ǒ
Ǔ
(21)
For this design IL(RMS) = 10.22 A at VIN = 14 V to 1.8 V RDS(on)Q2(max) = 8.8 mΩ.
Table 5. Inductor Requirements VIN = 4.5 V
PARAMETER
SYMBOL
VALUE
UNITS
High-side MOSFET on-resistance
RDS(on)
17.3
mΩ
High-side MOSFET gate-to-drain
charge
QGD1
8.5
nC
Low-side MOSFET on-resistance
RDS(on)Q2
8.8
mΩ
The IRF7466 has an RDS(on)MAX of 17 mΩ at 4.5-V gate drive and only 8.0-nC VGD "Miller" charge with a 4.5-V
gate drive, and is chosen as a high-side FET. The IRF7834 has an RDS(on)MAX of 5.5 mΩ at 4.5-V gate drive and
44 nC of total gate charge. These two FETs have maximum total gate charges of 23 nC and 44 nC respectively,
which draws 40.2-mA from the 5-V regulator, less than its 50-mA minimum rating.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
23
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Boot Strap Capacitor
To ensure proper charging of the high-side FET gate, limit the ripple voltage on the boost capacitor to less than
50 mV.
C BOOST + 20 Q G1
(22)
Based on the IRF7466 MOSFET with a gate charge of 23 nC, we calculate minimum of 460 nF of capacitance.
The next higher standard value of 470 nF is selected for the bootstrap capacitor.
Input Bypass Capacitor (C6)
As suggested the TPS40192/93 datasheet, select a 1.0-μF ceramic bypass capacitor for VDD.
BP5 Bypass Capacitor (C5)
The TPS40192 recommends a minimum 1.0-μF ceramic capacitance to stabilize the 5-V regulator. To limit
regulator noise to less than 10 mV, the bypass capacitor is sized by using Equation 23.
C BP5 + 100
MAXǒQ G1, Q G2Ǔ
(23)
Since Q2 is larger than Q1 and Q2's total gate charge is 44 nC, a BP5 capacitor of 4.4-μF is calculated, and the
next larger standard value of 4.7 μF is selected to limit noise on the BP5 regulator.
Input Voltage Filter Resistor (R11)
VIN(min) > 6.0 V so a 0 Ω resistor is placed in the VDD resistor location. If VIN(min) was < 6.0 V, an optional 1Ω to 2
Ω series VDD resistor could be used to filter switching noise from the device. Limit the voltage drop across this
resistor to less than 50 mV.
VRVDD(max)
50 mV
R VDD t
+
I DD
3 mA ) ǒQ G1, Q G2Ǔ f SW
(24)
Driving the two FETs with 23 nC and 44 nC respectively, we calculate a maximum IVDD current of 43 mA and
would select a 1-Ωresistor.
Short Circuit Protection (R9)
The TPS40192/93 use the negative drop across the low-side FET during the OFF time to measure the inductor
current. The voltage drop across the low-side FET is given by Equation 25.
V CS + I L(peak) RDS(on)
(25)
When 8 V ≤ VIN ≤14 V, IL(peak) = 11.5 A Using the IRF7834 MOSFET, we calculate a peak voltage drop of
63.3 mV.
The TPS40192's internal temperature coefficient helps compensate for the MOSFET's RDS(on) temperature
coefficient. For this design select the short circuit protection voltage threshold of 110 mV by selecting R9 =
3.9 kΩ.
24
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Feedback Compensation
Modeling the Power Stage
The DC gain of the modulator is given by Equation 26.
dV OUT
dt
1
A MOD +
+ dD
V IN +
dVCOMP
V COMP
dV RAMP T SW
V IN
(26)
Since the peak-to-peak ramp voltage given in the Electrical Characteristics Table is projected from the ramp
slope over a full switching period, the modulator gain can be calculated as Equation 27.
V IN
A MOD +
VRAMP(p*p)
(27)
This design finds a maximum modulator gain of 14 (23.0 dB). The L-C filter applies a double pole at the
resonance frequency described in Equation 28.
1
f RES +
Ǹ
2p
L C
(28)
For this design with a 1.0-μH inductor and 2 100-μF capacitors, the resonance frequency is approximately
11.3 kHz. At any lower frequency, the power stage has a DC gain of 23 dB and at any higher frequency the
power stage gain drops off at -40 dB per decade. The ESR zero is approximated in Equation 29.
1
f ESR +
2p C OUT R ESR
(29)
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
25
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
For COUT = 2, 100-μF and RESR = 2.5 mΩ each, fESR = 636 kHz, greater than 1/5th the switching frequency and
outside the scope of the error amplifier design. The gain of the power stage would change to -20 dB per decade
above fESR. The straight line approximation the power stage gain is described in Figure 18.
fRES
−40 dB/decade
AMOD
0 dB
−20 dB/decade
fESR
Frequency (Log Scale)
Figure 18. Approximation of Power Stage Gain
The following compensation design procedure assumes fESR > fRES. For designs using large high-ESR bulk
capacitors on the output where fESR < fRES. Type-II compensation can be used but is not addressed in this
document.
C3
3
R6
C1
R8
VOUT
2
C2
+
To
PWM
R10
+
VFB
R7
11
Power Pad
UDG−06068
Figure 19. Type-III Compensator Used with TPS40040/41
26
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
Feedback Divider (R7, R8)
Select R8 to be between 10 kΩ and 100 kΩ. For this design, select 20 kΩ. R7 is then selected to produce the
desired output voltage when VFB = 0.591 V using Equation 30.
V FB R8
R7 +
V OUT * V FB
(30)
VFB = 0.591 V and R8 = 20 kΩ for VOUT = 1.8 V, R7 = 9.78 kΩ, so the value of 9.76 kΩ is selected as the closest
standard value. A slightly lower nominal value increases the nominal output voltage slightly to compensate for
some trace impedance at load.
Error Amplifier Compensation (R6, R10, C1, C2, C3)
Place two zeros at 50% and 100% of the resonance frequency to boost the phase margin before resonance
frequency generates -180° of phase shift. For fRES = 11.7 kHz, FZ1 = 5.8 kHz and FZ2 = 11 kHz. Selecting the
crossover frequency (fCO) of the control loop between 3 times the LC filter resonance and 1/5th the switching
frequency. For most applications 1/10th the switching frequency provides a good balance between ease of
design and fast transient response.
• If fESR < fCO FP1 = fESR and FP2 = 4 × fCO.
• If fESR > 2 × fCO; FP1 = fCO and FP2 = 8 × fCO.
For this design
• fSW = 600 kHz,
• fRES = 11.7 kHz
• fESR = 636 kHz
• fCO = 60 kHz and since
• fESR > 2 × fCO, FP1 = fCO = 60 kHz and FP2 = 4 × fCO = 500 kHz.
Since fCO < fESR the power stage gain at the desired crossover can be approximated in Equation 31.
A PS(fco) + AMOD(dc) * 40
LOG
ǒ Ǔ
f CO
f RES
(31)
5.4 dB/20
APS(FCC) = -5.4 dB, and the error amplifier gain between the poles should be should be 10
= 1.86.
Table 6. Error Amplifier Design Parameters
PARAMETER
SYMBOL
VALUE
FZ1
5.8
Second zero frequency
FZ2
11.0
First pole frequency
FP1
60
First zero frequency
Second pole frequency
Midband gain
FP2
500
AMID(band)
1.86
UNITS
kHz
V/V
Approximate C2 with the formula described in Equation 32.
1
C2 +
2p R8 f Z2
(32)
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
27
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
C2 = 1000 pf (A standard capacitor value to calculated 723 pF) and approximate R6 with the formula described
in Equation 33.
1
R10 +
2p C2 f P1
(33)
R10 = 2.61 kΩ (Closest standard resistor value to calculated 2.65 kΩ ) Calculate R3 with Equation 34.
A MID(band) (R10 R8)
R6 +
R10 ) R8
(34)
With AMID(band) = 1.86, R10 = 2.61 kΩ and R8 = 20 kΩ , R6 = 4.22 kΩ (Closest standard resistor value to
calculated 4.29 kΩ ).
Calculate C1 and C3 using Equation 35 and Equation 36.
1
C3 +
2p R6 f Z1
C1 +
2p
1
R6
(35)
f P1
(36)
For R6 = 4.22kΩ , C1 = 100 pF (a standard value close to 75 pF) C3 = 1000 pF (the closest standard value to
7.5 nF) error amplifier straight line approximation transfer function is described in Figure 20.
fP1
fP2
0 dB
AMID(band)
fZ1
fZ2
Frequency (Log Scale)
Figure 20. Error Amplifier Transfer Function Approximation
28
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
List of Materials
Table 7. List of Materials
QTY
RefDe
s
Value
Description
Size
Part Number
MFR
1
C1
100 pF
Capacitor, Ceramic, 10V, C0G, 10%
0603
STD
STD
1
C2
1000 pF
Capacitor, Ceramic, 10V, C0G, 10%
0603
STD
STD
1
C3
10 nF
Capacitor, Ceramic, 10V, C0G, 10%
0603
STD
STD
1
C4
1.0 μF
Capacitor, Ceramic, 25V, X5R, 20%
0805
STD
STD
1
C5
4.7 μF
Capacitor, Ceramic, 10V, X5R, 20%
0805
STD
STD
1
C6
470 nF
Capacitor, Ceramic, 10V, X5R, 20%
0603
Std
Std
2
C7
10 μF
Capacitor, Ceramic, 25V, X5R, 20%
1210
C3225X7R1E106M
TDK
2
C8
100 μF
Capacitor, Ceramic, 6.3V, X5R, 20%
1210
C3225X5R0J107M
TDK
1
C11
1.0 μF
Capacitor, Ceramic, 6.3V, X5R, 20%
0603
STD
STD
1
L1
1.0 μH
Inductor, SMT, 1.0-μF, 6.6 mΩ, 12 A / 17 A
0.268 x
0.268 inch
PG0083.102
Pulse
1
Q1
2N7002W
Mosfet, N-Ch, VDS 60 V, RDS(on) 2 Ω, IDD 115 mA
SOT-323
(SC-70)
2N7002W-7
Diodes Inc
1
Q2
IRF7466
Transistor, MOSFET, N-channel, 30 V,
RDS(on) 17 mΩ, 9 A
SO8
IRF7466
IR
1
Q3
IRF7834
Transistor, MOSFET, N-channel, 30 V,
RDS(on) 5.5 mΩ, 9 A
SO8
IRF7834
IR
1
R1
5.1 kΩ
Resistor, Chip, 1/16W, 5%
0603
Std
Std
1
R2
2 kΩ
Resistor, Chip, 1/16W, 5%
0603
Std
Std
1
R4
100 kΩ
Resistor, Chip, 1/16W, 1%
0603
Std
Std
1
R6
4.22 kΩ
Resistor, Chip, 1/16W, 1%
0603
Std
Std
1
R7
9.76 kΩ
Resistor, Chip, 1/16W, 1%
0603
Std
Std
1
R8
20 kΩ
Resistor, Chip, 1/16W, 1%
0603
Std
Std
1
R9
3.9 kΩ
Resistor, Chip, 1/16W, 5%
0603
Std
Std
1
R10
2.61 kΩ
Resistor, Chip, 1/16W, 1%
0603
Std
Std
2
R11,
R13
0
Resistor, Chip, 1/16W, 5%
0603
Std
Std
1
R12
100 kΩ
Resistor, Chip, 1/16W, 5%
0603
Std
Std
1
U1
TPS40192DRC
Cost Optimized Midrange Input Votlage
High-Frequancy Synchronous Buck Controller
DRC10
TPS40192DRC
TI
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
29
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
DEFINITION OF SYMBOLS
Table 8. Definition of Symbols
SYMBOL
DESCRIPTION
VIN(max)
Maximum Operating Input Voltage
VIN(min)
Minimum Operating Input Voltage
VIN(ripple)
Peak to Peak AC ripple voltage on VIN
VOUT
Target Output Voltage
VOUT(ripple)
Peak to Peak AC ripple voltage on VOUT
IOUT(max)
Maximum Operating Load Current
IRIPPLE
Peak-to-Peak ripple current through Inductor
IL(peak)
Peak Current through Inductor
IL(rms)
Root Mean Squared Current through Inductor
IRMS(Cin)
Root Mean Squared Current through Input Capacitor
fSW
Switching Frequency
fCO
Desired Control Loop Crossover frequency
AMOD
Low Frequency Gain of the PWM Modulator ( VOUT / VCONTROL)
VCONTROL
PWM Control Voltage (Error Amplifier Output Voltage VCOMP)
fRES
L-C Filter Resonant Frequency
fESR
Output Capacitors' ESR zero Frequency
FP1
First Pole Frequency in Error Amplifier Compensation
FP2
Second Pole Frequency in Error Amplifier Compensation
FZ1
First Zero Frequency in Error Amplifier Compensation
FZ2
Second Pole Frequency in Error Amplifier Compensation
QG1
Total Gate Charge of Main MOSFET
QG2
Total Gate Charge of SR MOSFET
RDS(on)Q1
"ON" Drain to Source Resistance of Main MOSFET
RDS(on)Q2
"ON" Drain to Source Resistance of SR MOSEFT
PQ1C(on)
Conduction Losses in Main Switching MOSFET
PQ1SW
Switching Losses in Main Switching MOSFET
PQ2C(on)
Conduction Losses in Synchronous Rectifier MOSFET
QGD
Gate to Drain Charge of Synchronous Rectifier MOSFET
QGS
Gate to Source Charge of Synchronous Rectifier MOSFET
30
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
TPS40192, TPS40193
www.ti.com
SLUS719B – MARCH 2007 – REVISED SEPTEMBER 2007
ADDITIONAL REFERENCES
Related Parts
The following parts have characteristics similar to the TPS40192/3 and may be of interest.
Related Parts
DEVICE
DESCRIPTION
TPS40100
Midrange Input Synchronous Controller with Advanced Sequencing and Output Margining
TPS40075
Wide Input Synchronous Controller with Voltage Feed Forward
TPS40190
Low Pin Count Synchronous Buck Controller
References
These references may be found on the web at www.power.ti.com under Technical Documents. Many design
tools and links to additional references, including design software, may also be found at www.power.ti.com
1. Under The Hood Of Low Voltage DC/DC Converters, SEM1500 Topdevice 5, 2002 Seminar Series
2. Understanding Buck Power Stages in Switchmode Power Supplies, SLVA057, March 1999
3. Design and Application Guide for High Speed MOSFET Gate Drive Circuits, SEM 1400, 2001 Seminar
Series
4. Designing Stable Control Loops, SEM 1400, 2001 Seminar Series
5. Additional PowerPADTM information may be found in Applications Briefs SLMA002 and SLMA004
6. QFN/SON PCB Attachment, Texas Instruments Literature Number SLUA271, June 2002
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS40192 TPS40193
31
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS40192DRCR
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS40192DRCRG4
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS40192DRCT
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS40192DRCTG4
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS40193DRCR
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS40193DRCRG4
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS40193DRCT
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS40193DRCTG4
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Oct-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS40192DRCR
DRC
10
SITE 41
330
12
3.3
3.3
1.1
8
12
Q2
TPS40192DRCT
DRC
10
SITE 41
180
12
3.3
3.3
1.1
8
12
Q2
TPS40193DRCR
DRC
10
SITE 41
330
12
3.3
3.3
1.1
8
12
Q2
TPS40193DRCT
DRC
10
SITE 41
180
12
3.3
3.3
1.1
8
12
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Oct-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
TPS40192DRCR
DRC
10
SITE 41
346.0
346.0
29.0
TPS40192DRCT
DRC
10
SITE 41
190.0
212.7
31.75
TPS40193DRCR
DRC
10
SITE 41
346.0
346.0
29.0
TPS40193DRCT
DRC
10
SITE 41
190.0
212.7
31.75
Pack Materials-Page 2
Height (mm)
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated