MITEL 1A192

PRODUCT INFORMATION
880nm
1A192
High-Performance LED
This device generates very high
power which makes it ideal for many
sensors and signal transmission
applications. It operates in a wide
range of temperatures, and can satisfy virtually any environmental specification. The double-lens optical system results in optimum coupling of
power into the fiber.
Sensors, Signal Transmission
Optical and Electrical Characteristics
(25° C Case Temperature)
PARAMETER
UNIT
TEST CONDITION
µW
IF =100 mA
Fiber-Coupled Power
(Fig.1, 2,& 3) (Table 1)
Rise and Fall Time
(10-90%)
SYMBOL
MIN.
TYP.
Pfiber
80
115
MAX.
Fiber:
(Note 1)
tr,tf
8
fc
45
12
ns
50/125µm
IF =100 mA
Graded
(no bias)
Index
Bandwidth
(3dBel)
Peak Wavelength
lp
Spectral Width (FWHM)
Dl
50
Forward Voltage (Fig.5)
VF
1.8
Reverse Current
IR
Capacitance
C
860
880
MHz
IF =100 mA
nm
IF =100 mA
nm
IF =100 mA
2.2
V
IF =100 mA
20
µA
VR=1V
pF
VR= 0V, f=1 MHz
900
250
NA=0.20
Note 1: Measured at the exit of 100 meters of fiber.
Absolute Maximum Ratings
PARAMETER
Ø4.7
Ø1.5
0.6
3.7
SYMBOL
LIMIT
Storage Temperature
Tstg
-55 to +125°C
Operating Temperature (derating: Fig.4)
Top
-55 to +125°C
Electrical Power Dissipation (derating: Fig.4)
Ptot
250 mW
IF
110 mA
IFRM
180 mA
Reverse Voltage
VR
1.5 V
Soldering Temperature (2mm from the case for 10 sec)
Tsld
260°C
Continuous Forward Current (f<10 kHz)
14
Peak Forward Current (duty cycle<50%, f>1 MHz)
0.4
ANODE
CATHODE
2.5
5.4
BOTTOM VIEW
All dimensions in mm
CASE
The anode is in electrical contact with the case.
TO-46 Package With Lens
Thermal Characteristics
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Thermal Resistance - Infinite Heat Sink
Rthjc
100
°C/W
Thermal Resistance - No Heat Sink
Rthja
400
°C/W
Temperature Coefficient - Optical Power dP/dTj
-0.4
%/°C
dl /dTj
0.3
nm/°C
Temperature Coefficient -Wavelength
11753.11 1992-09-01
Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10
Tel (44) 1291 436180 Fax (44) 1291 436771
America: Tel 1-800-96MITEL Fax (613) 592-6909
Asia:
Tel (65) 293 5312
Fax (65) 293 8527
1A192
880nm
High-Performance LED
Typical Fiber-Coupled Power
1000 µW
RELATIVE FIBER-COUPLED POWER
640 µW
80
60
40
r
r = opt.
Øc = 50 µm
20
z = opt.
Øc = 50 µm
80
z
60
40
20
z
0
0
0.5
1.0
1.5
2.0
2.5
3.0 mm
0
z - AXIAL DISPLACEMENT OF FIBER
FIGURE 3
%
20
40
60
80
100 m
r - RADIAL DISPLACEMENT OF FIBER
FIGURE 4
mW
100
300
80
MAX. ELECTRICAL POWER DISSIPATION
280 µW
200/230 µm
0.37
RELATIVE FIBER-COUPLED POWER
115 µW
Table 1
100/140 µm
0.29
100
r
RELATIVE FIBER-COUPLED POWER
62.5/125 µm
0.275
FIGURE 2
%
100
50% DUTY CYCLE
60
40
DC
20
HEAT SINKED
0
200
INFINITE
HEAT SINK
100
NO HEAT SINK
0
0
40
80
120
160
200 mA
FIGURE 5
mA
200
100
0
0
1
2
FORWARD VOLTAGE
0
50
100
OPERATING TEMPERATURE
FORWARD CURRENT
FORWARD CURRENT
50/125 µm
0.20
FIGURE 1
%
CORE DIAMETER/CLADDING DIAMETER
NUMERICAL APERTURE
3V
150¡C
Clip for SC-2A
R 1.00
3.3000
5.6000
80,000
20.8200
0.5000
10,2500
10.3000
4.9500
0.5000
4.5000
5.0800
3.6450
Clip for Pigtail-3A
10.70
0.50
10.30
10.25
4.95
0.50
4.50
0.85
5.08
3.65
PRODUCT INFORMATION
ST-2A
Emitter or Detector in ST ® Package
Package
Mitel emitters and detectors can be
provided in this low-profile ST ®
package. The device is electrically
isolated from the ST ® receptacle to
facilitate electrical connection. And
optimum fiber-coupled power or
responsivity is ensured by active
alignment against the fiber.
Absolute Maximum Ratings
PARAMETER
SYMBOL
LIMIT
Operating & Storage Temperature
Tstg , Top
-40 to +858C
ST-2A (Note 1)
Note 1: Temperature range can be extended to -55° to +125°C on request.
Thermal Characteristics
PARAMETER
SYMBOL
Thermal Resistance - Infinite Heat Sink
(Note 2)
Thermal Resistance - No Heat Sink
(Note 2)
Thermal Resistance - On PC Board
MIN.
TYP.
MAX.
UNIT
Rthcc
40
8C/W
Rthca
200
8C/W
Rthca
8C/W
80
(Note 2)
Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance.
2-56 UNC - 2B
3/8"-32 UNEF
max.0.5
0.006
Ø2.502
+0.01
0
9.5
SLOT SIDE
MARKING SIDE
12.7
FIBER
END
Ø2.5
+0
-0.004
7.6
5.4
min.12
All Dimensions in mm
7.89
3.9
20.1
MATING FERRULE*
(not included)
*The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used.
Mechanical Outline of Diode in ST-2A Housing
(ST is a registered trademark of AT&T)
103326 1994-09-20
Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10
Tel (44) 1291 436180 Fax (44) 1291 436771
America: Tel 1-800-96MITEL Fax (613) 592-6909
Asia:
Tel (65) 293 5312
Fax (65) 293 8527
PRODUCT INFORMATION
SMA-2A
Emitter or Detector in SMA Package
Package
Mitel emitters and detectors can be
provided in this low-profile SMA
package. The device is electrically
isolated from the SMA receptacle to
facilitate electrical connection. And
optimum fiber-coupled power or
responsivity is ensured by active
alignment against the fiber.
Absolute Maximum Ratings
PARAMETER
SYMBOL
LIMIT
Tstg , Top
-40 to +858C
Operating & Storage Temperature
SMA-2A (Note 1)
Note 1: Temperature range can be extended to -55° to +125°C on request.
Thermal Characteristics
PARAMETER
SYMBOL
Thermal Resistance - Infinite Heat Sink
(Note 2)
Thermal Resistance - No Heat Sink
(Note 2)
Thermal Resistance - On PC Board
MIN.
MAX.
UNIT
Rthcc
40
8C/W
Rthca
200
8C/W
Rthca
TYP.
80
8C/W
(Note 2)
Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance.
2-56 UNC - 2B
+0.01
0
1/4"-36UNS
9.5
12.7
Ø3.176
FIBER
END
0.006
5.7
min.12
All Dimensions in mm
9.8 ± 0.03
+0
-0.004
3.9
7.2
Ø3.174
MARKING SIDE
max.0.5
15.2
MATING FERRULE*
(not included)
*The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used.
Mechanical Outline of Diode in SMA-2A Housing
103325 1994-09-20
Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10
Tel (44) 1291 436180 Fax (44) 1291 436771
America: Tel 1-800-96MITEL Fax (613) 592-6909
Asia:
Tel (65) 293 5312
Fax (65) 293 8527
PRODUCT INFORMATION
SC-2A
Emitter or Detector in SC Package
Package
Mitel emitters and detectors can be
provided in this low-profile SC package. The device is electrically isolated from the SC receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment
against the fiber..
Absolute Maximum Ratings
PARAMETER
SYMBOL
LIMIT
Operating & Storage Temperature
Tstg , Top
-40 to +858C
Thermal Characteristics
PARAMETER
SYMBOL
Thermal Resistance - Infinite Heat Sink
(Note 1)
Thermal Resistance - No Heat Sink
(Note 1)
Thermal Resistance - On PC Board
MAX.
UNIT
Rthcc
40
8C/W
Rthca
200
8C/W
Rthca
MIN.
TYP.
8C/W
125
(Note 1)
Note 1: Add Rthjc for emitter or detector to estimate the total thermal resistance.
2.5
1.
4
12
x4
MARKING / SLOT SIDE
0.006
13
Ø7.5
18
22
Ø2.3
FIBER
END
Ø2.5
+0
-0.004
7.95
MATING FERRULE*
(not included)
8.9
All Dimensions in mm
min. 12
18
* The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used.
Mechanical Outline of Diode in SC-2A Housing
105967 1994-09-20
Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10
Tel (44) 1291 436180 Fax (44) 1291 436771
America: Tel 1-800-96MITEL Fax (613) 592-6909
Asia:
Tel (65) 293 5312
Fax (65) 293 8527
PRODUCT INFORMATION
Pigtail-3A
Emitter or Detector in Pigtail Package
Package
Mitel emitters and detectors can be
provided in this pigtail package with
a wide selection of fiber types. The
device is electrically isolated from
the pigtail receptacle to facilitate
electrical connection. And optimum
fiber-coupled power or responsivity
is ensured by active alignment
against the fiber. A special design
maximizes the return loss for detectors in this package.
Absolute Maximum Ratings
PARAMETER
SYMBOL
LIMIT
Operating & Storage Temperature (Note 1 & 2)
Tstg , Top
- 40 to +858C
Note 1: Temperature range can be extended to -55/+1258C on request.
Note 2: Temperature range may be limited by the specification of the fiber.
Thermal Characteristics
PARAMETER
SYMBOL
Thermal Resistance - Infinite Heat Sink
(Note 3)
Thermal Resistance - No Heat Sink
(Note 3)
Thermal Resistance - On PC-Board
(Note 3)
MIN.
MAX.
UNIT
Rthcc
25
8C/W
Rthca
250
8C/W
Rthca
TYP.
8C/W
120
Note 3: Add Rthjc for LED to estimate the total thermal resistance.
Optical Characteristics
PARAMETER
Return Loss 10/125mm fiber
(PIN only)
SYMBOL
MIN.
TYP.
RL
40
55
MAX.
UNIT
dB
Ø6
MARKING
Ø6.00
min.12
13
All Dimensions in mm
Mechanical Outline of Diode in PIGTAIL-3A Housing
105429 1997-07-03
Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10
Tel (44) 1291 436180 Fax (44) 1291 436771
America: Tel 1-800-96MITEL Fax (613) 592-6909
Asia:
Tel (65) 293 5312
Fax (65) 293 8527
PRODUCT INFORMATION
FC-2A
Emitter or Detector in FC Package
Package
Mitel emitters and detectors can be
provided in this low-profile FC package. The device is electrically isolated from the FC receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment
against the fiber.
Absolute Maximum Ratings
PARAMETER
SYMBOL
LIMIT
Operating & Storage Temperature
Tstg , Top
-40 to +858C
FC-2A (Note 1)
Note 1: Temperature range can be extended to -55° to +125°C on request.
Thermal Characteristics
PARAMETER
SYMBOL
Thermal Resistance - Infinite Heat Sink
(Note 2)
Thermal Resistance - No Heat Sink
(Note 2)
Thermal Resistance - On PC Board
MIN.
MAX.
UNIT
Rthcc
40
8C/W
Rthca
200
8C/W
Rthca
TYP.
8C/W
80
(Note 2)
Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance.
min.12
5.6
2.0
5.50
Ø 2.5
0.006
13.4
MARKING/ SLOT SIDE
08
19
Ø 2.2
FIBER
END
Ø2.5
M8x0.75 Thread
max. 0.5
9.2
All Dimensions in mm
+0
-0.004
7.95
MATING FERRULE*
(not included)
* The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used.
Mechanical Outline of Diode in FC-2A Housing
105515 1994-09-20
Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10
Tel (44) 1291 436180 Fax (44) 1291 436771
America: Tel 1-800-96MITEL Fax (613) 592-6909
Asia:
Tel (65) 293 5312
Fax (65) 293 8527
http://www.mitelsemi.com
World Headquarters - Canada
Tel: +1 (613) 592 2122
Fax: +1 (613) 592 6909
North America
Tel: +1 (770) 486 0194
Fax: +1 (770) 631 8213
Asia/Pacific
Tel: +65 333 6193
Fax: +65 333 6192
Europe, Middle East,
and Africa (EMEA)
Tel: +44 (0) 1793 518528
Fax: +44 (0) 1793 518581
Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no
liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of
patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or
service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever.
Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or
other intellectual property rights owned by Mitel.
This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or
contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this
publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or
service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific
piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or
data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in
any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s
conditions of sale which are available on request.
M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation
Mitel Semiconductor is an ISO 9001 Registered Company
Copyright 1999 MITEL Corporation
All Rights Reserved
Printed in CANADA
TECHNICAL DOCUMENTATION - NOT FOR RESALE