PI5C3301 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Single Bit Bus Switch Product Features Product Description · · · · Pericom Semiconductor’s PI5C series of logic circuits are produced using the Company’s advanced submicron CMOS technology, achieving industry leading speed grades. · Near zero propagation delay 5-Ohm switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2µA Typical) – Ideally suited for notebook applications Packages available: – 5-pin plastic S0T23 (T) – 5-pin plastic SC70 (C) The PI5C3301 is a single digital switch designed with a fast enable. When enabled via the associated Bus Enable (BE) pin, the “A” pin is directly connected to the “B” pin. The bus switch introduces no additional propagation delay or additional ground bounce noise. The PI5C3301 device has an active LOW enable. Logic Block Diagram Product Pin Configuration A Truth Table(1) BE X* H L A Hi-Z Hi-Z B 1 B 2 GND 3 5 Vcc 4 BE 5-Pin C, T Product Pin Description B Hi-Z Hi-Z A Vcc GND Vcc Vcc Function Disconnect Disconnect Connect Pin Name BE A B Vcc GND Notes: 1. H = High Voltage Level L = Low Voltage Level HI-Z = High Impedance X = Don’t Care *A pull-up resistor should be provided for power-up protection. 1 Description Switch Enable Bus A Bus B Power Ground PS8366D 01/11/01 PI5C3301 Single Bit Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ............................................................. –65°C to +150°C Ambient Temperature with Power Applied ............................. –40°C to +85°C Supply Voltage to Ground Potential (Inputs & Vcc Only) ....... –0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only) .... –0.5V to +7.0V DC Input Voltage ...................................................................... –0.5V to +7.0V DC Output Current ............................................................................... 120mA Power Dissipation .................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V± 10%) Parame te rs Te s t Conditions (1) De s cription M in. Typ.(2) M ax. VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 VIL Input LOW Voltage Guaranteed Logic LOW Level - 0.5 IIH Input HIGH Current VCC = Max., VIN = VCC ±1 IIL Input LOW Current VCC = Max., VIN = GND ±1 Units V 0.8 IOZH High Impedence Output Current VCC = Max., VOUT = 0V or VCC ±1 IOZL Low Impedence Output Current VCC = Max., VOUT = 0V or VCC ±1 VH Input Hysteresis at Control Pins RON Switch On Resistance(3) µΑ 300 VCC = 4.5V, VCC = 4.5V, VIN = 0.0V, VIN = 2.4V, ION = 30mA or 64mA ION = 15mA VCC = 4V, VIN = 2.4V, ION = 15mA mV 5 10 7 15 14 20 Ω Capacitance (TA = 25°C, f = 1 MHz) Parameters Description Test Conditions CIN COFF Input Capacitance A/B Capacitance, Switch Off CON A/B Capacitance, Switch On (4) Typ. Units VIN = 0V VIN = 0V 3 5 pF pF VIN = 0V 10 pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determine by the lower of the voltages on the two (A, B) pins. 4. This parameter is determined by device characterization but is not production tested. 2 PS8366D 01/11/01 PI5C3301 Single Bit Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Power Supply Characteristics Test Conditions(1) Parameters Description ICC Quiescent Power Supply Current ∆ICC Supply Current per Input @ TTL HIGH VCC = Max. VIN = GND or VCC VCC = Max. 3.4V(3) VIN = Min. Typ.(2) Max. Units 0.1 3.0 µA 2.5 mA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V, control inputs only); A and B pins do not contribute to ICC. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design. Switching Characteristics over Operating Range Parameters Description t PLH t PHL t PZH t PZL t PHZ t PLZ Conditions(1) PI5C3301 VCC = 5V ± 10% VCC = 4V Min. Max. Min. Max. Propagation Delay(2,3) A to B, B to A Bus Enable Time CL = 50pF RL = 500Ω Bus Disable Time 0.25 0.25 1.0 4.9 5.5 1 4.2 4.5 Units ns Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Ordering Information Part Pin - Package PI5C3301TX 5 - SOT23 (T) PI5C3301CX 5 - SC70 (C) Te mpe rature –40ºC to +85ºC Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com 3 PS8366D 01/11/01