TOKO TK15329

TK15329
Audio Analog Switch
FEATURES
APPLICATIONS
■
■
■
■
■
■
■ Audio Systems
■ Radio Cassettes
Wide Operating Voltage Range (2 to 14 V)
Low Distortion (typ. 0.004%)
Wide Dynamic Range (typ. 6 VP-P)
Low Output Impedance (typ. 20 Ω)
Low Switching Noise (typ. 3 mV)
Output Parallel Connection Possible
DESCRIPTION
TK15329
The TK15329M is an Analog Switch IC that was developed
for audio frequency. The function is to select one output
from two inputs and has a floating position too. The
channel can be changed by two control levels and the
device includes two circuits. The TK15329M has a
mono-power supply and the input bias is a supply type
from outside. Because the distortion is very low, the
TK15329M fits various signals switching. It is best suited
for Hi-Fi devices. Operating voltage is wide, the circuit
plan is simple. The TK15329M is available in a small
plastic surface mount package (SSOP-12).
VCC
Bch
OUT
1ch-in
GND
11 Bch
10 OUT
Ach
9
Ach
1KEY
8
2 KEY
NC
7
NC
2ch-in
BLOCK DIAGRAM
VCC
Ach
+
1 ch out
-
1ch-in
2 ch out
1KEY
Bch
+
-
ORDERING INFORMATION
Ach
+
-
TK15329M
Logic
2KEY
2ch-in
Bch
Tape/Reel Code
+
-
GND
TAPE/REEL CODE
TL: Tape Left
June 1999 TOKO, Inc.
Page 1
TK15329
ABSOLUTE MAXIMUM RATINGS
Supply Voltage ......................................................... 15 V
Power Dissipation (Note 5) ................................ 350 mW
Storage Temperature Range ................... -55 to +150 °C
Operating Temperature Range ...................-20 to +75 °C
CONTROL SECTION
Input Voltage ................................... -0.3 V to VCC + 0.3 V
ANALOG SWITCH SECTION
Signal Input Voltage ........................ -0.3 V to VCC + 0.3 V
Signal Output Current ............................................. 3 mA
Operating Voltage Range ................................. 2 to 14 V
Maximum Input Frequency .................................. 100 kHz
TK15329M ELECTRICAL CHARACTERISTICS
Test conditions: VCC = 8.0 V, TA = 25 °C, unless otherwise specified.
SYMBOL
ICC
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
3.5
5.5
mA
-0.3
+0.8
V
1. 8
VCC + 0.3
V
Supply Current
KEY CONTROL SECTION
VIL
Input Voltage Low Level
VIH
Input Voltage High Level
ZIN
Input Impedance
Note 1
50
kΩ
ANALOG SWITCH SECTION
THD
Total Harmonic Distortion
VIN = 1 Vrms, f = 1 kHz
NL
Residual Noise
ISO
0.003
0.006
%
Note 2
10
µVrms
Isolation
VIN = 1 Vrms, F = 10 kHz,
Note 3
-75
dB
SE P
Separation
VIN = 1 Vrms, f = 10 kHz,
Note 3
-80
dB
D YN
Maximum Input Signal Level
f = 1 kHz, THD = 0.1%
GVA
Voltage Gain
f = ~20 kHz
Vcent
Input-Output Terminal
Voltage
VOUT = Supply voltage
from outside
∆Vcent
Output Terminal Voltage
Difference
Between same channel
IIN
Input Bias Current
Note 4
0.5
µA
ZOUT
Output Impedance
DC Impedance
20
Ω
2.0
0
VOUT - 0.2
Note 1: The KEY input equivalent circuit is shown in Figure A.
When the control pin is open, it is outputted at low level. The TK15329M is controlled
by two values and the function table is described in the block diagram.
Note 2: The specification means a value as measurement-input terminal connects to ground
Input Key
through a capacitor.
Note 3: ISO is a cross talk between A channel and B channel, SEP is a cross talk between 1
channel and 2 channel. The specification means a value as measurement-input
termianl connects to ground through 10 kΩ resistor and capacitor.
Note 4: The standard application of the TK15329M is the direct connecting. In case of the
capacitor connecting, the to supply a bias voltage from outside is unnecessary.
Note 5: Power dissipation is 350 mW when mounted as recommended. Derate at 3.0 mW/
°C for operation above 25°C.
Page 2
Vrms
dB
VOUT
VOUT + 0.2
V
3
7
mV
VCC
Input
Logic
Figure A
Figure B
June 1999 TOKO, Inc.
TK15329
TEST CIRCUITS AND METHODS
33 µF
+
VCC
SW6
+
SW3 10 µF
SW7
+
10 µF
SW9
SW4
SW8
50 kΩ
50 kΩ
SW2
1 kHz
1 Vrms
or
2 Vrms
1:
2:
3:
4:
~
SW1
SW5
10 kHz
1 Vrms
~
10 kΩ
VCC / 2
L
V
~
V
_
H L
H
THD
The above condition represents 1ch.
The above conditions distortion rate of 1-Ach and dynamic range measurement.
SW5 is for residual noise measurement.
SW8 is for cross talk (ISO or SEP) measurement.
SUPPLY CURRENT (FIGURE 1)
This current is a consumption current with a nonloading
condition.
1) Bias supply to Pin 2, 4, 9, 11. (This condition is the same
with other measurements, omitted from the next for
simplicity)
2) Connect Pin 5 to VCC, Pin 8 is inthe open condition or low
level.
3) Measure the inflow current to Pin 1 from VCC. This
current is the supply current.
VCC
A
50 K
50 K
50 K
50 K
VCC/2
Figure 1
June 1999 TOKO, Inc.
Page 3
TK15329
TEST CIRCUITS AND METHODS (CONT.)
CONTROL LOW/HIGH LEVEL (FIGURE 2)
This level is to measure the threshold level.
1) Input, the VCC to Pin 1. (This condition is the same with
other measurements, omitted from the next for simplicity)
2) Input to Pin 4 with sine wave (f = 1 kHz, VIN = 1 Vrms).
3) Connect an oscilloscope to Pin 3.
4) Pin 8 is in the open condition or low level. Elevate Pin
5 voltage gradually from 0 V until the sine wave appears
at the oscilloscope. This voltage is the threshold level,
when the wave appears.
VCC
+
VCC
Figure 3
+
+
TOTAL HARMONIC DISTORTION (FIGURE 4)
~
Cont.
Figure 2
CONTROL INPUT IMPEDANCE (FIGURE 3)
This is the input resistance of control terminals.
1) Measure the inflow current from VCC to Pin 5.
2) Calculate:
IMP = VCC / Inflow Current
This resistance is the input impedance.
Page 4
Use the lower distortion oscillator for this measurement
because distortion of the TK15329 is very low.
1) Connect VCC to Pin 5, Pin 8 is in the open condition or low
level.
2) Connect a distortion analyzer to Pin 3.
3) Input the sine wave (1 kHz, 1 Vrms) to Pin 4.
4) Measure the distortion of Pin 3. This value is the
distortion of 1-Ach.
5) Next, reverse conditions at Pin 5 and Pin 8.
6) Input the same sine wave to Pin 2.
7) Measure in the same way. This value is the distortion
of 1-Bch.
June 1999 TOKO, Inc.
TK15329
TEST CIRCUITS AND METHODS (CONT.)
VCC
VCC
+
+
+
Figure 4
+
Figure 5
VOLTAGE GAIN (FIGURE 5)
MAXIMUM INPUT LEVEL (FIGURE 6)
This is the output level against input level.
1) Connect VCC to Pin 5, Pin 8 is in the open condition or low
level.
2) Connect AC volt meters to Pin 4 and Pin 3.
(Using the same type meter is best)
3) Input a sine wave (f = max. 20 kHz, 1 Vrms) to Pin 4.
4) Measure the level of Pin 4 and name this V1.
5) Measure the level of Pin 3 and name this V2.
6) Calculate Gain = 20 Log (( |V2 - V1| )/V1)
V1<V2 + Gain, V1>V2 - Gain
This value is the voltage gain of 1-Ach.
7) Next, reverse conditions at Pin 5 and Pin 8.
8) Input the same sine wave to Pin 2.
9) Measure and calculate in the same way.
This value is the voltage gain of 1-Bch.
This measurement measures at output side.
1) Connect VCC to Pin 5, Pin 8 is low level or open.
2) Connect a distortion analyzer and an AC volt meter to
Pin 3.
3) Input a sine wave (1 kHz) to Pin 4 and elevate the voltage
gradually until the distortion gets to 0.1%.
4) When the distortion amounts to 0.1%, stop elevating and
measure the AC level of Pin 3.
This value is the maximum input level of 1-Ach.
5) Next, reverse conditions at Pin 5 and Pin 8.
6) Input the same sine wave to Pin 2.
7) Measure in the same way.
This value is the maximum input level of 1-Bch.
June 1999 TOKO, Inc.
Page 5
TK15329
TEST CIRCUITS AND METHODS (CONT.)
RESIDUAL NOISE (FIGURE 7)
ISOLATION (FIGURE 8)
This value is not S/N ratio. This is a noise which occurs from
the device itself.
1) Connect VCC to Pin 5, Pin 8 is the open condition or low
level.
2) Connect an AC volt meter to Pin 3.
3) Connect a capacitor from Pin 4 to GND.
4) Measure AC voltage of Pin 3. This value is the noise of
1-Ach. If the influence of noise from outside exists, use
optional filters.
5) Next, reverse conditions at Pin 5 and Pin 8.
6) Connect to GND through a capacitor from Pin 2.
7) Measure in the same way.
This value is the noise level of 1-Bch.
This is the cross talk between Ach and Bch.
1) Connect VCC to Pin 8, Pin 5 is in the open condition or
low level.
2) Connect AC volt meters to Pin 4 and Pin 3.
3) Connect a capacitor and a resistance in series to GND
from Pin 2.
4) Input a sine wave (10 kHz, 1 Vrms) to Pin 4.
5) Measure the level of Pin 4 and name this V4.
6) Measure the level of Pin 3 and name this V3.
7) Calculate:
ISO = 20 Log (V3 / V4)
This value is the isolation to Bch from Ach.
8) Next, reverse conditions at Pin 5 and Pin 8.
9) Change line of Pin 2 and Pin 4.
10) Input the same sine wave to Pin 2.
11) Measure and calculate in the same way.
This value is the isolation to Ach from Bch.
VCC
VCC
+
10 K
+
+
+
+
Figure 7
Page 6
Figure 8
June 1999 TOKO, Inc.
TK15329
TEST CIRCUITS AND METHODS (CONT.)
SEPARATION (FIGURE 9)
VCC
This is the cross talk between 1ch and 2ch.
1) Connect either Pin 5 or Pin 8 to VCC. One side pin is low
level or open.
2) Connect AC volt meters to Pin 4 (or Pin 2) and Pin 10.
3) Connect Pin 9 and Pin 11 to GND through capacitors
and a resistance.
4) Input a sine wave (10 kHz, 1 Vrms) to Pin 2 and Pin 4.
5) Measure the level of Pin 4 and name this V5.
6) Measure the level of Pin 10 and name this V6.
7) Calculate:
SEP = 20 Log (V6 / V5)
This value is the separation to 2ch from 1ch.
VCC
+
OUTPUT TERMINAL DIFFERENCE
+
+
+
+
Figure 10
+
10 K
This is the DC output voltage difference between Ach and
Bch. This is calculated by using values measured at the
I/O Terminal Voltage.
∆ Vcent = | (1 - Ach value) - (1 - Bch value) |
This value is the voltage difference of 1ch.
Figure 9
I/O TERMINAL VOLTAGE (FIGURE 10)
This is the DC voltage of input and output.
Because the input and the output are nearly equal, only the
output is measured.
1) Connect VCC to Pin 5, Pin 8 is in the open condition or low
level.
2) Connect a DC volt meter to Pin 3 and measure.
This value is the terminal voltage of 1-Ach.
3) Next, reverse conditions at Pin 5 and Pin 8.
4) Measure in the same way.
This value is the terminal voltage of 1-Bch.
June 1999 TOKO, Inc.
Page 7
TK15329
TYPICAL PERFORMANCE CHARACTERISTICS
VCC = 8 V, TA = 25 °C, unless otherwise specified.
TOTAL HARMONIC DISTORTION
vs. FREQUENCY
SUPPLY CURRENT VS.
SUPPLY VOLTAGE
0.1
6
5
THD (%)
ICC (mA)
4
3
0.01
2
1
0
0
2
4
6
8
10 12
14
0.001
0.1
16
1
10
100
VCC (V)
f (kHz)
TOTAL HARMONIC DISTORTION
vs. LOAD RESISTANCE
DYNAMIC RANGE
vs. SUPPLY VOLTAGE
0.1
5
LEVEL (Vrms)
THD (%)
4
0.01
3
2
1
0.001
0.1
0
1
10
100
0
2
4
6
8
10
12 14
RL (kΩ)
VCC (V)
DYNAMIC RANGE
vs. LOAD RESISTANCE
ISOLATION
vs. FREQUENCY
16
-60
-70
LEVEL (dB)
LEVEL (Vrms)
2
1
-80
-90
-100
0
0.1
1
10
RL (kΩ)
Page 8
100
-110
0.1
1
10
100
f (kHz)
June 1999 TOKO, Inc.
TK15329
TYPICAL PERFORMANCE CHARACTERISTICS
VCC = 8 V, TA = 25 °C, unless otherwise specified.
SEPARATION
vs. FREQUENCY
CONTROL THRESHOLD VS.
TEMPERATURE
-60
1.5
LEVEL (V)
LEVEL (dB)
-70
-80
-90
1
0.5
-100
-110
0.1
0
1
10
100
-20
20
40
60
f (kHz)
TA (°C)
VOLTAGE GAIN VS.
TEMPERATURE
RESIDUAL NOISE VS.
TEMPERATURE
+.1
80
6
LEVEL (µVrms)
GVA (dB)
0
0
-.1
4
2
0
-20
0
20
40
60
80
-20
0
20
40
60
TA (°C)
TA (°C)
OUTPUT DIFFERENCE VS.
TEMPERATURE
INPUT BIAS CURRENT VS.
TEMPERATURE
80
1.2
1.0
CURRENT (µA)
LEVEL (mV)
3
2
1
.8
.6
.4
.2
0
0
-20
0
20
40
TA (°C)
June 1999 TOKO, Inc.
60
80
-20
0
20
40
60
80
TA (°C)
Page 9
TK15329
FUNCTION TABLE
1KEY
2KEY
OUT
Lo
Lo
Floating
Hi
Lo
Ach
Lo
Hi
Bch
Hi
Hi
Floating
TERMINAL VOLTAGE AND CIRCUIT
Condition: VCC = 8 V.
PIN NO.
ASSIGNMENT
DC VOLTAGE
1
VCC
8V
2
4
9
11
IN A, IN B
3
10
Input: Open
0V
Input: 4.0 V
4V
CIRCUIT/FUNCTION
Supply Voltage Pin
Signal Input Pin
OUT
100
5
8
Input: Open
0.7 V
Input: 4.0 V
4V
KEY
0V
Signal Output Pin
50 K
Control Pin
Page 10
12
GND
0V
6
7
NC
Floating
Ground Pin
No Contact Pin
June 1999 TOKO, Inc.
TK15329
APPLICATION INFORMATION
1Ain
KEY INPUT CIRCUIT
2Ain
33 µF
+
1ch and 2ch is separate action by each control keys. Figure
11 is an equivalence circuit of key input. If two keys are low
level or high level at the same time then the output is floating
condition. (See Terminal DC Voltage and Circuit table on
page 9).
10 µF
10 µF
11
+
+
10
9
8
RL
RL
7
Key in
to Logic
1Key
2Key
2 Bin
1Bin
Figure 11
SWITCHING TIME
Figure 13
CROSS TALK (ISOLATION AND SEPARATION)
This time is the signal change response time compared to
the control key input signal. Figure 12 illustrates the timimg
chart. T = 2 µs typically.
Bch (Ach)
Key in
SW out
50%
t
Ach (Bch)
Figure 12
Figure 14 is an example of a layout pattern. In the
application of the TK15329M, the following must be
considered. Because of the high impedance at the inputs,
the capacitors can act as antennas to each other. If the
parts are bigger, and the space between the capacitors is
too narrow, then cross talk will increase. Therefore, when
designing the printed circuit pattern, separate the input
capacitors as far as possible and use as small a part as
possible (e.g., surface mount types, etc.).
2AIN
VCC
GND
2BIN
APPLICATION
Figure 13 illustrates an example of a typical application.
The standard application is to use direct coupling at the
inputs and capacitor coupling at the outputs of the
TK15329M. For characteristics of distortion and dynamic
range versus RL, refer to the graphs in the Typical Performance Characteristics. The TK15329M can also be used
with direct coupling, but the characteristics will get worse
(distortion, etc.). If capacitor coupling is desired, then it is
recommended to use built-in type biased circuitry of the
TK15327M. DC input bias voltage of TK15327M is VCC/2 V.
1OUT
1AIN
2OUT
1KEY
2KEY
1BIN
Figure 14
June 1999 TOKO, Inc.
Page 11
TK15329
APPLICATION INFORMATION (CONT.)
OUTPUT TERMINAL VOLTAGE DIFFERENCE
FLOATING POSITION
This parameter is the output voltage difference between
Ach and Bch, and appears when the channel changes from
Ach to Bch, or changes to the reverse. Generally, this is
called Switching Noise or Pop Noise. If this value is big and
if this noise is amplified by the final amplifier and is
outputted by the speakers, then it appears as a Shock
Sound. Output terminal voltage difference of the TK15329M
is a value that adds the internal bias difference and the offset voltage difference. The off-set voltage difference is
very small, its typical value is 3 mV, but the input bias is
supplied from the outside.
So almost the output bias difference will be decided by the
supply bias difference. The TK15329M has a floating
position. Pay attention when operating as for the change
timing of the two keys. If the floating condition is long, then
the output voltage may fluctuate by RL and the difference
may appear larger. Toko can offer the “Muting IC” if users
wish to mute Switching Noise.
TK15329M has floating position and can increase optional
channels. Figure 15 is an example to select one output
from four inputs, and the change operates by four controls.
This function is shown in the table below. If channels
increase more, control keys will increase with the same
number too. In this case the Decoder may be necessary.
Each device and channel has individual output voltage
values within a specification. When channels are increased caution the output terminal voltage difference too.
1ch-in
a
b
2ch-in
d VCC
c
d
c
a
b
+
+
+
+
+
+
+
+
+
11
10
327-1
9
DIRECT TOUCH
8
7
11
10
327-2
+
9
+
The signal input terminals:
Internal circuits are operated by constant current circuit,
even if VCC or GND is contacted, damage does not occur.
The signal output terminal:
Outflow or inflow current is decided by ability of final
transistor, but protection circuit is not attached. If GND or
VCC are contacted damage may occur. Pay attention to
long time contact. Do not supply over the maximum rating.
Referenced to GND, do not provide to all terminals over VCC
+0.3 V or -0.3 V.
8
7
1ch-out
control
1 2
3
4
2ch-out
Figure 15
DC SIGNAL INPUT
FUNCTION TABLE
The output of the TK15329M has a saturation voltage (both
VCC and GND sides about 1.0 V); accordingly the use of a
DC signal is not recommend (e.g., the pulse signal etc.)
KEY NO.
1
2
3
4
OUTPUT
NC TERMINAL
c
H
L
L
L
NC terminals are not wired inside IC by bonding wire. NC
terminals are not tested so do not connect at outside.
a
L
H
L
L
b
L
L
H
L
d
L
L
L
H
When all is high level or low level, output is the floating.
Plural high level is prohibited.
Page 12
June 1999 TOKO, Inc.
TK15329
NOTES
June 1999 TOKO, Inc.
Page 13
TK15329
NOTES
Page 14
June 1999 TOKO, Inc.
TK15329
NOTES
June 1999 TOKO, Inc.
Page 15
TK15329
PACKAGE OUTLINE
Marking Information
SSOP-12
TK15329M
329
1.2
0.4
Marking
12
e1 5.4
7
4.4
AAA
e 0.8
YYY
Recommended Mount Pad
1
6
Lot. No.
0 ~ 10
1.7 max
+0.15
-0.15
0.5
+0.15
0.3 -0.05
0.15
0 ~ 0.2
1.4
5.0
e 0.8
0.1
6.0
0.10
+ 0.3
M
Dimensions are shown in millimeters
Tolerance: x.x = ± 0.2 mm (unless otherwise specified)
Toko America, Inc. Headquarters
1250 Feehanville Drive, Mount Prospect, Illinois 60056
Tel: (847) 297-0070
Fax: (847) 699-7864
TOKO AMERICA REGIONAL OFFICES
Midwest Regional Office
Toko America, Inc.
1250 Feehanville Drive
Mount Prospect, IL 60056
Tel: (847) 297-0070
Fax: (847) 699-7864
Western Regional Office
Toko America, Inc.
2480 North First Street , Suite 260
San Jose, CA 95131
Tel: (408) 432-8281
Fax: (408) 943-9790
Eastern Regional Office
Toko America, Inc.
107 Mill Plain Road
Danbury, CT 06811
Tel: (203) 748-6871
Fax: (203) 797-1223
Semiconductor Technical Support
Toko Design Center
4755 Forge Road
Colorado Springs, CO 80907
Tel: (719) 528-2200
Fax: (719) 528-2375
Visit our Internet site at http://www.tokoam.com
The information furnished by TOKO, Inc. is believed to be accurate and reliable. However, TOKO reserves the right to make changes or improvements in the design, specification or manufacture of its
products without further notice. TOKO does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of
third parties which may result from the use of its products. No license is granted by implication or otherwise under any patent or patent rights of TOKO, Inc.
Page 16
© 1999 Toko, Inc.
All Rights Reserved
June 1999 TOKO, Inc.
IC-119-TK119xx
0798O0.0K
Printed in the USA