Preliminary W78C51D 8-BIT MICROCONTROLLER GENERAL DESCRIPTION The W78C51D microcontroller supplies a wider frequency and supply voltage range than most 8-bit microcontrollers on the market. It is compatible with the industry standard 80C51 microcontroller series. The W78C51D contains four 8-bit bidirectional parallel ports, one extra 4-bit bit-addressable I/O port (Port 4) and two additional external interrupts ( INT2 , INT3 ), two 16-bit timer/counters, one watchdog timer and a serial port. These peripherals are supported by a seven-source, two-level interrupt capability. There are 128 bytes of RAM and an 4K byte mask ROM for application programs. The W78C51D microcontroller has two power reduction modes, idle mode and power-down mode, both of which are software selectable. The idle mode turns off the processor clock but allows for continued peripheral operation. The power-down mode stops the crystal oscillator for minimum power consumption. The external clock can be stopped at any time and in any state without affecting the processor. FEATURES • Fully static design • Supply voltage of 4.5V to 5.5V • DC-40 MHz operation • 128 bytes of on-chip scratchpad RAM • 4K bytes of on-chip mask ROM • 64K bytes program memory address space • 64K bytes data memory address space • Four 8-bit bidirectional ports • Two 16-bit timer/counters • One full duplex serial port • Seven-source, two-level interrupt capability • One extra 4-bit bit-addressable I/O port • Two additional external interrupts INT2 / INT3 • Watchdog timer • EMI reduction mode • Built-in power management • Code protection • Packages: − DIP 40: W78C51D-24/40 − PLCC 44: W78C51DP-24/40 − QFP 44: W78C51DF-24/40 -1- Publication Release Date: January 1999 Revision A1 Preliminary W78C51D PIN CONFIGURATIONS 40-Pin DIP (W78C51D) 1 P1.0 P1.1 40 39 2 3 4 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 RST 38 37 5 6 36 35 7 8 34 33 32 9 10 11 RXD, P3.0 TXD, P3.1 INT0, P3.2 INT1, P3.3 T0, P3.4 T1, P3.5 WR, P3.6 RD, P3.7 XTAL2 XTAL1 P1.5 P1.6 P1.7 RST RXD, P3.0 A D 0 , P 0 . 0 A D 1 , P 0 . 1 A D 2 , P 0 . 2 12 13 29 28 14 15 16 27 26 25 PSEN P2.7, A15 P2.6, A14 17 18 24 23 22 21 6 5 4 3 2 1 44 43 42 41 40 39 38 8 37 9 36 10 35 11 12 13 INT1, P3.3 T0, P3.4 15 16 17 18 19 20 21 22 23 24 25 26 27 14 P 3 . 7 , / R D X T A L 2 P2.5, A13 P2.4, A12 P2.3, A11 P2.2, A10 P2.1, A9 P2.0, A8 X V P P P T S 4 2 2 A S . . . L 0 0 1 1 , , A A 8 9 P 2 . 2 , A 1 0 P 2 . 3 , A 1 1 / I N T 3 , P P P P P P 1 1 1 1 1 4 V . . . . . . D 4 3 2 1 0 2 D A D 3 , P 0 . 3 7 P 3 . 6 , / W R P0.6, AD6 P0.7, AD7 44-Pin QFP (W78C51DF) INT2, P4.3 TXD, P3.1 INT0, P3.2 T1, P3.5 P0.3, AD3 P0.4, AD4 P0.5, AD5 EA ALE 44-Pin PLCC (W78C51DP) / I N T 3 , P P P P P P 1 1 1 1 1 4 V . . . . . . D 4 3 2 1 0 2 D P0.0, AD0 P0.1, AD1 P0.2, AD2 31 30 19 20 VSS VDD P0.4, AD4 P0.5, AD5 P0.6, AD6 P0.7, AD7 34 EA P4.1 33 32 ALE 31 30 29 28 P 2 . 4 , A 1 2 A D 3 , P 0 . 3 44 43 42 41 40 39 38 37 36 35 34 33 32 P1.7 RST RXD, P3.0 3 4 5 31 30 29 P0.6, AD6 P0.7, AD7 INT2, P4.3 TXD, P3.1 6 7 8 9 28 P4.1 ALE 27 26 25 10 24 23 11 12 13 14 15 16 17 18 19 20 21 22 P 3 . 6 , / W R -2- A D 2 , P 0 . 2 1 2 INT1, P3.3 T0, P3.4 T1, P3.5 P2.5, A13 A D 1 , P 0 . 1 P1.5 P1.6 INT0, P3.2 PSEN P2.7, A15 P2.6, A14 A D 0 , P 0 . 0 P 3 . 7 , / R D X T A L 2 X V P P T S 4 2 A S . . L 0 0 1 , A 8 P 2 . 1 , A 9 P 2 . 2 , A 1 0 P 2 . 3 , A 1 1 P 2 . 4 , A 1 2 P0.4, AD4 P0.5, AD5 EA PSEN P2.7, A15 P2.6, A14 P2.5, A13 Preliminary W78C51D PIN DESCRIPTION P0.0−P0.7 Port 0, Bits 0 through 7. Port 0 is a bidirectional I/O port. This port also provides a multiplexed low order address/data bus during accesses to external memory. P1.0−P1.7 Port 1, Bits 0 through 7. Port 1 is a bidirectional I/O port with internal pull-ups. P2.0−P2.7 Port 2, Bits 0 through 7. Port 2 is a bidirectional I/O port with internal pull-ups. This port also provides the upper address bits for accesses to external memory. P3.0−P3.7 Port 3, Bits 0 through 7. Port 3 is a bidirectional I/O port with internal pull-ups. All bits have alternate functions, which are described below: PIN P3.0 P3.1 P3.2 ALTERNATE FUNCTION RXD Serial Receive Data TXD Serial Transmit Data P3.3 INT1 External Interrupt 1 T0 Timer 0 Input T1 Timer 1 Input P3.4 P3.5 P3.6 P3.7 INT0 External Interrupt 0 WR Data Write Strobe RD Data Read Strobe P4.0−P4.3 Another bit-addressable bidirectional I/O port P4. P4.3 and P4.2 are alternative function pins. It can be used as general I/O pins or external interrupt input sources ( INT2 / INT3 ). EA External Address Input, active low. This pin forces the processor to execute out of external ROM. This pin should be kept low for all W78C31 operations. RST Reset Input, active high. This pin resets the processor. It must be kept high for at least two machine cycles in order to be recognized by the processor. ALE Address Latch Enable Output, active high. ALE is used to enable the address latch that separates the address from the data on Port 0. ALE runs at 1/6th of the oscillator frequency. A single ALE pulse is skipped during external data memory accesses. ALE goes to a high impedance state during reset with a weak pull-up. -3- Publication Release Date: January 1999 Revision A1 Preliminary W78C51D PSEN Program Store Enable Output, active low. PSEN enables the external ROM onto the Port 0 address/data bus during fetch and MOVC operations. PSEN goes to a high impedance state during reset with a weak pull-up. XTAL1 Crystal 1. This is the crystal oscillator input. This pin may be driven by an external clock. XTAL2 Crystal 2. This is the crystal oscillator output. It is the inversion of XTAL1. VSS, VDD Power Supplies. These are the chip ground and positive supplies. BLOCK DIAGRAM P1.0 ~ P1.7 Port 1 Port 1 Latch ACC B INT2 Port 0 Interrupt INT3 T1 Latch T2 Port 0 P0.0 ~ P0.7 DPTR Timer 0 Stack Pointer PSW ALU Temp Reg. Timer 1 PC Incrementor UART Addr. Reg. P3.0 ~ P3.7 Port 3 Port 3 SFR RAM Address Instruction Decoder & Sequencer Latch 128bytes RAM & SFR Bus & Clock Controller P4.0 ~ P4.3 Port 4 Port 2 Latch 4KB ROM Port 4 Latch Watchdog Timer Oscillator XTAL1 Reset Block XTAL2 ALE PSEN RST -4- Power control VDD GND Port 2 P2.0 ~ P2.7 Preliminary W78C51D FUNCTIONAL DESCRIPTION The W78C51D architecture consists of a core controller surrounded by various registers, five general purpose I/O ports, 128 bytes of RAM, two timer/counters, one watchdog timer and a serial port. The processor supports 111 different opcodes and references both a 64K program address space and a 64 K data storage space. Timers 0, 1 Timers 0, 1 each consist of two 8-bit data registers. These are called TL0 and TH0 for Timer 0, TL1 and TH1 for Timer 1. The TCON and TMOD registers provide control functions for timers 0, 1. Clock The W78C51D is designed to be used with either a crystal oscillator or an external clock. Internally, the clock is divided by two before it is used. This makes the W78C51D relatively insensitive to duty cycle variations in the clock. Crystal Oscillator The W78C51D incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must be connected across pins XTAL1 and XTAL2. In addition, a load capacitor must be connected from each pin to ground, and a resistor must also be connected from XTAL1 to XTAL2 to provide a DC bias when the crystal frequency is above 24 MHz. External Clock An external clock should be connected to pin XTAL1. Pin XTAL2 should be left unconnected. The XTAL1 input is a CMOS-type input, as required by the crystal oscillator. As a result, the external clock signal should have an input high level of greater than 3.5 volts when VDD = 5 volts. Power Management Idle Mode The idle mode is entered by setting the IDL bit in the PCON register. In the idle mode, the internal clock to the processor is stopped. The peripherals and the interrupt logic continue to be clocked. The processor will exit idle mode when either an interrupt or a reset occurs. Power-down Mode When the PD bit of the PCON register is set, the processor enters the power-down mode. In this mode all of the clocks, including the oscillator are stopped. The only way to exit power-down mode is by a reset. Reset The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to deglitch the reset line when the W78C51D is used with an external RC network. The reset logic also has a special glitch removal circuit that ignores glitches on the reset line. During reset, the ports are initialized to FFH, the stack pointer to 07H, PCON (with the exception of bit 4) to 00H, and all of the other SFR registers except SBUF to 00H. SBUF is not reset. -5- Publication Release Date: January 1999 Revision A1 Preliminary W78C51D New Defined Peripheral In order to be more suitable for I/O, an extra 4-bit bit-addressable port P4 and two external interrupts INT2 , INT3 have been added to either the PLCC or QFP package. And description follows: 1. INT2 / INT3 Two additional external interrupts, INT2 and INT3 , whose functions are similar to those of external interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are determined/shown by the bits in the XICON (External Interrupt Control) register. The XICON register is bit-addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To set/clear bits in the XICON register, one can use the "SETB (/CLR) bit" instruction. For example, "SETB 0C2H" sets the EX2 bit of XICON. ***XICON - external interrupt control (C0H) PX3 EX3 IE3 IT3 PX2 EX2 IE2 IT2 PX3: External interrupt 3 priority high if set EX3: External interrupt 3 enable if set IE3: If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced IT3: External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software PX2: External interrupt 2 priority high if set EX2: External interrupt 2 enable if set IE2: If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced IT2: External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software Eight-source interrupt informations: INTERRUPT SOURCE VECTOR ADDRESS POLLING SEQUENCE WITHIN PRIORITY LEVEL ENABLE REQUIRED SETTINGS INTERRUPT TYPE EDGE/LEVEL External Interrupt 0 03H 0 (highest) IE.0 TCON.0 Timer/Counter 0 0BH 1 IE.1 - External Interrupt 1 13H 2 IE.2 TCON.2 Timer/Counter 1 1BH 3 IE.3 - Serial Port 23H 4 IE.4 - Timer/Counter 2 2BH 5 IE.5 - External Interrupt 2 33H 6 XICON.2 XICON.0 External Interrupt 3 3BH 7 (lowest) XICON.6 XICON.3 2. PORT4 Another bit-addressable port P4 is also available and only 4 bits (P4<3:0>) can be used. This port address is located at 0D8H with the same function as that of port P1, except the P4.3 and P4.2 are -6- Preliminary W78C51D alternative function pins. It can be used as general I/O pins or external interrupt input sources ( INT2 / INT3 ). Example: P4 REG 0D8H MOV P4, #0AH ; Output data "A" through P4.0−P4.3. MOV A, P4 ; Read P4 status to Accumulator. SETB P4.0 ; Set bit P4.0 CLR P4.1 ; Clear bit P4.1 Watchdog Timer The Watchdog timer is a free-running timer which can be programmed by the user to serve as a system monitor, a time-base generator or an event timer. It is basically a set of dividers that divide the system clock. The divider output is selectable and determines the time-out interval. When the time-out occurs a system reset can also be caused if it is enabled. The main use of the Watchdog timer is as a system monitor. This is important in real-time control applications. In case of power glitches or electro-magnetic interference, the processor may begin to execute errant code. If this is left unchecked the entire system may crash. The watchdog time-out selection will result in different time-out values depending on the clock speed. The Watchdog timer will de disabled on reset. In general, software should restart the Watchdog timer to put it into a known state. The control bits that support the Watchdog timer are discussed below. Watchdog Timer Control Register Bit: 7 6 5 4 3 2 1 0 ENW CLRW WIDL - - PS2 PS1 PS0 Mnemonic: WDTC Address: 8FH ENW : Enable watch-dog if set. CLRW : Clear watch-dog timer and prescaler if set. This flag will be cleared automatically WIDL : If this bit is set, watch-dog is enabled under IDLE mode. If cleared, watch-dog is disabled under IDLE mode. Default is cleared. PS2, PS1, PS0 : Watch-dog prescaler timer select. Prescaler is selected when set PS2~0 as follows: PS2 PS1 PS0 0 0 0 0 1 0 0 0 1 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 PRESCALER SELECT 2 4 8 16 32 64 128 256 -7- Publication Release Date: January 1999 Revision A1 Preliminary W78C51D The time-out period is obtained using the following formula: 1 × 214 × PRESCALER × 1000 × 12 mS OSC Before Watchdog time-out occurs, the program must clear the 14-bit timer by writing 1 to WDTC.6 (CLRW). After 1 is written to this bit, the 14-bit timer , prescaler and this bit will be reset on the next instruction cycle. The Watchdog timer is cleared on reset. ENW WIDL IDLE EXTERNAL RESET OSC 1/12 Watchdog Timer Block Diagram INTERNAL RESET 14-BIT TIMER PRESCALER CLEAR CLRW Typical Watchdog time-out period when OSC = 20 MHz PS2 PS1 PS0 0 0 0 0 1 0 0 0 1 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 WATCHDOG TIME-OUT PERIOD 19.66 mS 39.32 mS 78.64 mS 157.28 mS 314.57 mS 629.14 mS 1.25 S 2.50 S Reduce EMI Emission Because of the on-chip ROM, when a program is running in internal ROM space, the ALE will be unused. The transition of ALE will cause noise, so it can be turned off to reduce the EMI emission if it is not needed. Turning off the ALE signal transition only requires setting the bit 0 of the AUXR SFR, which is located at 08Eh. When ALE is turned off, it will be reactivated when the program accesses external ROM/RAM data or jumps to execute an external ROM code. The ALE signal will turn off again after it has been completely accessed or the program returns to internal ROM code space. AUXR - Auxiliary Register Bit: 7 6 5 4 3 2 1 0 - - - - - - - AO Mnemonic: AUXR AO: Address: 8Eh Turn off ALE signal. -8- Preliminary W78C51D ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL MIN. MAX. UNIT VCC−VSS -0.3 +7.0 V Input Voltage VIN VSS -0.3 VCC +0.3 V Operating Temperature TA 0 70 °C Storage Temperature TST -55 +150 °C DC Power Supply Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. DC CHARACTERISTICS (VDD−VSS = 5V ±10%, TA = 25°C, Fosc = 20 MHz, unless otherwise specified.) PARAMETER SYM. SPECIFICATION MIN. MAX. UNIT TEST CONDITIONS Operating Voltage VDD 4.5 5.5 V Operating Current IDD - 20 mA VDD = 5.5V, 20 MHz, no load IIDLE - 6 mA VDD = 5.5V, 20 MHz, no load IPWDN - 50 µA VDD = 5.5V, no load IIN -50 +10 µA VDD = 5.5V Idle Current Power Down Current Input Current P1, P2, P3, P4 Input Leakage Current VIN = 0V or VDD ILK -10 +10 µA VSS < VIN < VDD P0, EA Input Current VDD = 5.5V IIN2 -10 +300 µA RST VDD = 5.5V 0 < VIN < VDD Logic 1-to-0 Transition Current ITL -500 - µA P1, P2, P3, P4 VDD = 5.5V VIN = 2V Input Input Low Voltage VIL1 0 0.8 V VDD = 4.5V VIL2 0 0.8 V VDD = 4.5V VIL3 0 0.8 V VDD = 4.5V P1, P2, P3, P4 Input Low Voltage RST Input Low Voltage [*4] XTAL1 -9- Publication Release Date: January 1999 Revision A1 Preliminary W78C51D DC Characteristics, continued PARAMETER SYM. SPECIFICATION TEST CONDITIONS MIN. MAX. UNIT VIH1 2.4 VDD +0.2 V VDD = 5.5V VIH2 3.5 VDD +0.2 V VDD = 5.5V VIH3 3.5 VDD +0.2 V VDD = 5.5V - 0.45 V VDD = 4.5V Input Input High Voltage P1, P2, P3, P4 Input High Voltage RST Input High Voltage [*4] XTAL1 Output Output Low Voltage VOL1 P1, P2, P3, P4 IOL = +2 mA Output Low Voltage P0, ALE, PSEN VOL2 - 0.45 V Sink Current ISK1 4 10 mA P1, P2, P3, P4 ISK2 8 16 mA Output High Voltage VOH1 2.4 - V VDD = 4.5V IOH = -100 µA P1, P2, P3, P4 Output High Voltage VOH2 2.4 - V VDD = 4.5V IOH = -400 µA [*4] ISR1 -100 -250 µA P1, P2, P3, P4 Source Current VDD = 4.5V VIN = 0.45V P0, ALE, PSEN Source Current VDD = 4.5V Vin = 0.45V Sink Current P0, ALE, PSEN VDD = 4.5V IOL = +4 mA [*4] VDD = 4.5V VIN = 2.4V ISR2 -8 -14 mA VDD = 4.5V VIN = 2.4V P0, ALE, PSEN Notes: *1. RST pin has an internal pull-down. *2. Pins of P1 and P3 can source a transition current when they are being externally driven from 1 to 0. *3. RST is a Schmitt trigger input and XTAL1 is a CMOS input. *4. P0, P2, ALE and PSEN are tested in the external access mode. - 10 - Preliminary W78C51D AC CHARACTERISTICS The AC specifications are a function of the particular process used to manufacture the part, the ratings of the I/O buffers, the capacitive load, and the internal routing capacitance. Most of the specifications can be expressed in terms of multiple input clock periods (TCP), and actual parts will usually experience less than a ±20 nS variation. The numbers below represent the performance expected from a 0.5 micron CMOS process when using 2 and 4 mA output buffers. Clock Input Waveform XTAL1 T CH TCL F OP, PARAMETER TCP SYMBOL MIN. TYP. MAX. UNIT NOTES Operating Speed FOP 0 - 40 MHz 1 Clock Period TCP 25 - - nS 2 Clock High TCH 10 - - nS 3 Clock Low TCL 10 - - nS 3 Notes: 1. The clock may be stopped indefinitely in either state. 2. The TCP specification is used as a reference in other specifications. 3. There are no duty cycle requirements on the XTAL1 input. Program Fetch Cycle PARAMETER SYMBOL MIN. TYP. MAX. UNIT NOTES Address Valid to ALE Low TAAS 1 TCP-∆ - - nS 4 Address Hold from ALE Low TAAH 1 TCP-∆ - - nS 1, 4 ALE Low to PSEN Low TAPL 1 TCP-∆ - - nS 4 PSEN Low to Data Valid TPDA - - 2 TCP nS 2 Data Hold after PSEN High TPDH 0 - 1 TCP nS 3 Data Float after PSEN High TPDZ 0 - 1 TCP nS ALE Pulse Width TALW 2 TCP-∆ 2 TCP - nS 4 PSEN Pulse Width TPSW 3 TCP-∆ 3 TCP - nS 4 Notes: 1. P0.0−P0.7, P2.0−P2.7 remain stable throughout entire memory cycle. 2. Memory access time is 3 TCP. 3. Data have been latched internally prior to PSEN going high. 4. "∆" (due to buffer driving delay and wire loading) is 20 nS. - 11 - Publication Release Date: January 1999 Revision A1 Preliminary W78C51D Data Read Cycle PARAMETER SYMBOL MIN. TYP. MAX. UNIT NOTES ALE Low to RD Low TDAR 3 TCP-∆ - 3 TCP+∆ nS 1, 2 RD Low to Data Valid TDDA - - 4 TCP nS 1 Data Hold from RD High TDDH 0 - 2 TCP nS Data Float from RD High TDDZ 0 - 2 TCP nS RD Pulse Width TDRD 6 TCP-∆ 6 TCP - nS SYMBOL MIN. TYP. MAX. UNIT ALE Low to WR Low TDAW 3 TCP-∆ - 3 TCP+∆ nS Data Valid to WR Low TDAD 1 TCP-∆ - - nS Data Hold from WR High TDWD 1 TCP-∆ - - nS WR Pulse Width TDWR 6 TCP-∆ 6 TCP - nS SYMBOL MIN. TYP. MAX. UNIT Port Input Setup to ALE Low TPDS 1 TCP - - nS Port Input Hold from ALE Low TPDH 0 - - nS Port Output to ALE TPDA 1 TCP - - nS Notes: 1. Data memory access time is 8 TCP. 2. "∆" (due to buffer driving delay and wire loading) is 20 nS. Data Write Cycle PARAMETER Note: "∆" (due to buffer driving delay and wire loading) is 20 nS. Port Access Cycle PARAMETER Note: Ports are read during S5P2, and output data becomes available at the end of S6P2. The timing data are referenced to ALE, since it provides a convenient reference. - 12 - 2 Preliminary W78C51D TIMING WAVEFORMS Program Fetch Cycle S1 S2 S3 S4 S5 S6 S1 S2 S3 S4 S5 S6 XTAL1 TALW ALE TAPL PSEN TPSW TAAS PORT 2 TPDA TAAH TPDH, TPDZ PORT 0 A0-A7 Code Data A0-A7 A0-A7 Code Data A0-A7 Data Read Cycle S4 S5 S6 S1 S2 S3 S4 S5 S6 S1 S2 S3 XTAL1 ALE PSEN PORT 2 A8-A15 DATA A0-A7 PORT 0 T DAR T DDA T DDH, T DDZ RD T DRD - 13 - Publication Release Date: January 1999 Revision A1 Preliminary W78C51D Timing Waveforms, continued Data Write Cycle S4 S5 S6 S1 S2 S3 S4 S5 S6 S1 S2 XTAL1 ALE PSEN A8-A15 PORT 2 PORT 0 A0-A7 DATA OUT T DWD TDAD WR T DWR T DAW Port Access Cycle S5 S6 S1 XTAL1 ALE TPDS T PDA T PDH DATA OUT PORT INPUT SAMPLE - 14 - S3 Preliminary W78C51D APPLICATION CIRCUITS Expanded External Program Memory and Crystal VDD VDD 31 19 10 u CRYSTAL 8.2 K XTAL1 R 18 XTAL2 9 C1 EA RST C2 12 13 14 15 INT0 INT1 T0 T1 1 2 3 4 5 6 7 8 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 39 AD0 38 AD1 37 AD2 36 AD3 35 AD4 34 AD5 33 AD6 32 AD7 AD0 3 AD1 4 AD2 7 AD3 8 AD413 AD514 AD617 AD718 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 21 22 23 24 25 26 27 28 GND 1 OC 11 G RD WR PSEN ALE TXD RXD 17 16 29 30 11 10 A8 A9 A10 A11 A12 A13 A14 A15 D0 D1 D2 D3 D4 D5 D6 D7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 74HC373 2 A0 5 A1 6 A2 9 A3 12 A4 15 A5 16 A6 19 A7 A0 10 A1 9 A2 8 A3 7 A4 6 A5 5 A6 4 A7 3 A8 25 A9 24 A10 21 A11 23 A12 2 A13 26 A14 27 A15 1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 O0 O1 O2 O3 O4 O5 O6 O7 11 12 13 15 16 17 18 19 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND 20 CE 22 OE 27LV512 W78C51D Figure A CRYSTAL C1 C2 R 16 MHz 30P 30P − 24 MHz 15P 15P 33 MHz 10P 10P − 6.8K 40 MHz 5P 5P 4.7K Above table shows the reference values for crystal applications. Note: C1, C2, R components refer to Figure A. - 15 - Publication Release Date: January 1999 Revision A1 Preliminary W78C51D Application Circuits, continued Expanded External Data Memory and Oscillator VDD VDD 31 10 u 19 EA XTAL1 18 XTAL2 9 RST OSCILLATOR 8.2 K 12 13 14 15 1 2 3 4 5 6 7 8 INT0 INT1 T0 T1 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 39 38 37 36 35 34 33 32 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 21 22 23 24 25 26 27 28 A8 A9 A10 A11 A12 A13 A14 RD 17 16 29 30 11 10 WR PSEN ALE TXD RXD AD0 3 AD1 4 AD2 7 AD3 8 AD4 13 AD5 14 AD6 17 AD7 18 D0 D1 D2 D3 D4 D5 D6 D7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 2 5 6 9 12 15 16 19 GND 1 OC 11 G 74HC373 A0 A1 A2 A3 A4 A5 A6 A7 A0 10 A1 9 A2 8 A3 7 A4 6 A5 5 A6 4 A7 3 A8 25 A9 24 A10 21 A11 23 A12 2 A13 26 A14 1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 GND 20 22 27 CE OE WR 20256 W78C51D Figure B - 16 - D0 11 D1 12 D2 13 D3 15 D4 16 D5 17 D6 18 D7 19 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 Preliminary W78C51D PACKAGE DIMENSIONS 40-pin DIP Dimension in inch Dimension in mm Min. Nom. Max. Min. Nom. Max. Symbol D 40 21 E1 0.010 0.150 0.155 0.160 3.81 3.937 4.064 0.016 0.018 0.022 0.406 0.457 0.559 0.048 0.050 0.054 1.219 1.27 1.372 0.008 0.010 0.014 0.203 0.254 0.356 2.055 2.070 52.20 52.58 0.600 0.610 14.986 15.24 15.494 0.540 0.545 0.550 13.72 13.84 13.97 0.090 0.100 0.110 2.286 2.54 2.794 0.120 0.130 0.140 3.048 3.302 3.556 15 0 0.670 16.00 16.51 17.01 0 eA S 20 0.254 0.590 a 1 5.334 0.210 A A1 A2 B B1 c D E E1 e1 L 0.630 0.650 15 0.090 2.286 Notes: E S 1. Dimension D Max. & S include mold flash or tie bar burrs. 2. Dimension E1 does not include interlead flash. 3. Dimension D & E1 include mold mismatch and . parting line. are determined at the mold 4. Dimension B1 does not include dambar protrusion/intrusion. 5. Controlling dimension: Inches. 6. General appearance spec. should be based on final visual inspection spec. c A A2 A1 Base Plane Seating Plane L B e1 eA a B1 44-pin PLCC HD D 6 1 44 40 Symbol 7 39 E 17 HE GE 29 18 28 c A A1 A2 b1 b c D E e GD GE HD HE L y Dimension in inch Dimension in mm Min. Nom. Max. Min. Nom. Max. 0.185 0.020 4.699 0.508 0.145 0.150 0.155 0.026 0.028 0.032 0.016 0.018 0.022 0.008 0.010 0.014 0.203 0.254 0.356 0.648 0.653 0.658 16.46 16.59 16.71 0.648 0.653 0.658 16.46 16.59 16.71 0.050 BSC 3.81 3.937 0.66 0.711 0.813 0.406 0.457 0.559 3.683 1.27 BSC 0.590 0.610 0.630 14.99 15.49 0.590 0.610 0.630 14.99 15.49 16.00 0.680 0.690 0.700 17.27 17.53 17.78 16.00 0.680 0.690 0.700 17.27 17.53 17.78 0.090 0.100 0.110 2.296 2.54 2.794 0.004 0.10 L Notes: A2 A 1. Dimension D & E do not include interlead flash. 2. Dimension b1 does not include dambar protrusion/intrusion. 3. Controlling dimension: Inches 4. General appearance spec. should be based on final visual inspection spec. θ e b b1 Seating Plane A1 y GD - 17 - Publication Release Date: January 1999 Revision A1 Preliminary W78C51D Package Dimensions, continued 44-pin QFP HD Symbol 34 A A1 A2 b c D E e HD HE L L1 y θ 33 1 E HE 11 12 e Dimension in mm Dimension in inch D 44 b 22 Min. Nom. Max. Min. Nom. Max. --- --- --- --- 0.002 0.01 0.02 0.05 0.25 0.5 0.075 0.081 0.087 1.90 2.05 2.20 0.01 0.014 0.018 0.25 0.35 0.45 0.004 0.006 0.010 0.101 0.152 0.254 0.390 0.394 0.398 9.9 10.00 10.1 0.390 0.394 0.398 9.9 10.00 10.1 0.025 0.031 0.036 0.635 0.80 0.952 0.510 0.520 0.530 12.95 13.2 13.45 13.45 --- --- 0.510 0.520 0.530 12.95 13.2 0.025 0.031 0.037 0.65 0.8 0.95 0.051 0.063 0.075 1.295 1.6 1.905 0.08 0.003 0 7 0 7 Notes: 1. Dimension D & E do not include interlead flash. 2. Dimension b does not include dambar protrusion/intrusion. 3. Controlling dimension: Millimeter 4. General appearance spec. should be based on final visual inspection spec. c A2 A θ A1 Seating Plane See Detail F L y L1 Headquarters Detail F Winbond Electronics (H.K.) Ltd. Rm. 803, World Trade Square, Tower II, No. 4, Creation Rd. III, 123 Hoi Bun Rd., Kwun Tong, Science-Based Industrial Park, Kowloon, Hong Kong Hsinchu, Taiwan TEL: 852-27513100 TEL: 886-3-5770066 FAX: 852-27552064 FAX: 886-3-5792766 http://www.winbond.com.tw/ Voice & Fax-on-demand: 886-2-27197006 Taipei Office 11F, No. 115, Sec. 3, Min-Sheng East Rd., Taipei, Taiwan TEL: 886-2-27190505 FAX: 886-2-27197502 Note: All data and specifications are subject to change without notice. - 18 - Winbond Electronics North America Corp. Winbond Memory Lab. Winbond Microelectronics Corp. Winbond Systems Lab. 2727 N. First Street, San Jose, CA 95134, U.S.A. TEL: 408-9436666 FAX: 408-5441798