TI TS3DV20812RHHR

TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
2-Gbps DIFFERENTIAL SWITCH 8-Bit, 1:2 MULTIPLEXER/DEMULTIPLEXER
WITH 3-SIDE BAND SIGNALS
Check for Samples: TS3DV20812
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
1
•
•
•
•
•
•
•
•
•
•
•
•
Four High-Speed Bidirectional Differential Pair
Channel MUX/DEMUX
Supports up to 2 Gbps Data Rate
VDD Operating Range 2.5 V or 3.3
– -0 V to 3.3 V Rail To Rail at 2.5 V
– -0 V to 5 V Rail To Rail at 3.3V
IOFF partial Powerdown and Back-Drive
Protection.
5-V Input Tolerant on Control Pin
Supports Both AC- and DC-Coupled Signals
Low Crosstalk: -38 dB at 825 MHz,
2.5 V or 3.3 V
Insertion Loss: -1.5 dB at 825 MHz,
2.5 V or 3.3 V
Off Isolation -24.67 dB at 825 MHz
Low Bit-to-Bit Skew within Pair 5 ps Maximum
Channel-to-Channel Skew: 30 ps Maximum
Propagation Delay Times: 250 ps Maximum
ESD Performance Tested per JESD 22
– 2000-V Human Body Model
(A114-B, Class II)
– 1000-V Charged-Device Model (C101)
HDMI/DVI Video MUX
Panel LVDS Bus MUX
LVDS, LVPECL, CML
Analog Signals VGA
Gigabit LAN Signal MUX
Serial Backplane Signal MUX
Optical Module
Central Office Telecommunication
Wireless Base Station
High-Speed Logic Data I/O MUX
RHH PACKAGE
(TOP VIEW)
DESCRIPTION/ORDERING INFORMATION
TS3DV20812 is a High Speed Data Rate up to 2Gbps for Differential Signal Passive bi-directional Multiplexer
and De-multiplexer for I/O rails up to 5V Level with Low Crosstalk and Insertion Loss.
TS3DV20812 can be used in either HDMI/DVI sink side or source side with 4-differential pair supporting the high
speed and control pins.
The Ioff and back drive protection allowing to connect the external cable and prevent the back flow current when
the Vcc is into 0V.
The 3 side band signals can be used in DDC (SDAL, SCL) and CEC Signal MUX.
TS3DS20812 is characterized for operation from -40C to 85C.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
TS3DV20812
SCDS302 – JUNE 2010
www.ti.com
Table 1. ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
(2)
QFN – RHH
(2)
ORDERABLE PART NUMBER
Tape and reel
TS3DV20812RHH
TOP-SIDE MARKING
TBD
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
LOGIC DIAGRAM
FUNCTION TABLE
INPUT
SEL
DIFFERENTIAL
SIGNAL I/Os
L
Dn (±), nA (AUX (±),
HPD, CAD/CEC)
H
2
FUNCTIONS
A-PORT
B-PORT
DnA (±), nA_A
High-impedance mode
High-impedance mode
DnB (±), nA_B
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VDD
Supply voltage range
VIN
Control input voltage range (2) (3)
VIO
Switch I/O voltage range (all three I/O ports)
(4)
MIN
MAX
–0.5
4.6
V
SEL
–0.5
7
V
I/O
–0.5
7
V
D0-D3, Aux, HPD, CAD/CEC
–0.5
VCC + 0.5
V
A port and B port
–0.5
VCC + 0.5
IIK
Control input clamp current
VIN < 0
II/OK
I/O port clamp current
VO < 0
IIO
Continuous output current (5)
ON-state switch
Continuous current through VDD or GND
ΘJA
Package thermal impedance
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(5)
(6)
(6)
RHH package
–65
UNIT
V
–50
mA
–50
mA
±128
mA
±100
mA
31.8
°C/W
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to ground, unless otherwise specified.
The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
VI and VO are used to denote specific conditions for VIO.
II and IO are used to denote specific conditions for IIO.
The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS
MIN
MAX
UNIT
2.25
3. 6
V
SEL
2
5.5
V
Low-level control input voltage
SEL
0
0.8
V
Input/output voltage
All ports
0
5.5
V
VANALOG
Analog signal range
Differential signal range
0
VDD
V
VI
Input tolerant
SEL
0
5.5
V
TA
Operating free-air temperature
–40
85
°C
VDD
Supply voltage
VIH
High-level control input voltage
VIL
VI/O
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
3
TS3DV20812
SCDS302 – JUNE 2010
www.ti.com
ELECTRICAL CHARACTERISTICS
for high-frequency switching over recommended operating free-air temperature range VDD = 3.3 V ± 0.3 V (unless otherwise
noted)
TEST CONDITIONS (1)
PARAMETER
VIK
SEL
VDD = 3.6 V,
IIN = –18 mA
IIH
SEL
VDD = 3.6 V,
VIN = VDD
IIL
SEL
VDD = 3.6 V,
VIN = GND
VDD = 06 V,
VO = 0 to 3.6 V ,
VI = 0 , VIN = 0
Switch ON or OFF
IOFF
ICC
MIN
TYP (2)
MAX
–0.7
–1.2
V
±1
mA
±1
mA
1
mA
250
500
mA
2
2.5
pF
4
pF
VDD = 3.6 V,
IIO = 0
CIN
SEL
f = 10 MHz ,
VIN = 0
COFF
3-Port
f = 10 MHz ,
VIN = 0 ,
Output is Open, Switch is
OFF
2.5
CON
3-Port
f = 10 MHz ,
VIN = 0 ,
Output is Open, Switch is
ON
8
VDD = 3.6 V
1.5 V ≤ VI ≤ VDD,
IO = –40 mA
4
VDD = 3.6 V
1.5 V ≤ VI ≤ VDD,
IO = –40 mA
0.5
VDD = 3.6 V
1.5 V ≤ VI ≤ VDD,
IO = –40 mA
0.4
rON
rON(flat)
(3)
Δ rON (4)
(1)
(2)
(3)
(4)
UNIT
pF
6
Ω
Ω
1
Ω
VI, VO, II, and IO refer to I/O pins, VIN refers to the control inputs.
All typical values are at VDD = 3.3 V (unless otherwise noted), TA = 25°.
rON(flat) is the difference of rON in a given channel at specified voltages.
ΔrON is the difference of rON from center (D0 to Dn) ports to any other port.
ELECTRICAL CHARACTERISTICS
for high-frequency switching over recommended operating free-air temperature range VDD = 2.5 V ± 0.25 V (unless otherwise
noted)
TEST CONDITIONS (1)
PARAMETER
MIN
TYP (2)
MAX
–0.7
UNIT
VIK
SEL
VDD = 2.5 V ,
IIN = –18 mA
–1.2
V
IIH
SEL
VDD = 2.5 V ,
VIN = VDD
±1
mA
IIL
SEL
VDD = 2.5 V ,
VIN = GND
±1
mA
IOFF
VDD = 06 V,
VO = 0 to 2.5 V ,
VI = 0 , VIN = 0
ICC
VDD = 2.5 V ,
IIO = 0
Switch ON or OFF
1
mA
250
500
mA
2
2.5
pF
4
pF
CIN
SEL
f = 10 MHz ,
VIN = 0
COFF
3-Port
f = 10 MHz ,
VIN = 0 ,
Output is Open, Switch is
OFF
2.5
CON
3-Port
f = 10 MHz ,
VIN = 0 ,
Output is Open, Switch is
ON
8
VDD = 2.5 V
1.5 V ≤ VI ≤ VDD,
IO = –40 mA
4
VDD = 2.5 V
VI = 1.5 V and VDD,
IO = –40 mA
0.5
VDD = 2.5 V
1.5 V ≤ VI ≤ VDD,
IO = –40 mA
0.4
rON
rON(flat)
(3)
Δ rON (4)
(1)
(2)
(3)
(4)
4
pF
6
Ω
Ω
1
Ω
VI, VO, II, and IO refer to I/O pins, VIN refers to the control inputs.
All typical values are at VDD = 2.5 V (unless otherwise noted), TA = 25°.
rON(flat) is the difference of rON in a given channel at specified voltages.
ΔrON is the difference of rON from center (D0 to Dn) ports to any other port.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VDD = 3.3 V ± 0.3 V, RL = 200 Ω, CL = 10 pF (unless otherwise
noted) (see Figure 9 and Figure 10)
MIN
TYP (1)
FROM
(INPUT)
TO
(OUTPUT)
tpd (2)
Dn
DA or DB
tPZH, tPZL
SEL
DA or DB
0.5
15
ns
tPHZ, tPLZ
SEL
DA or DB
0.9
12
ns
PARAMETER
MAX
149
UNIT
ps
SEL to switch turn on time
DA or DB
9
14
ns
SEL to switch turn off time
DA or DB
5
11
ns
Dn (+)(-), DA(+)(-), DB(+)(-)
22
28
ps
Dn (all), DnA(all), DnB(All)
19
25
ps
22
31
ps
tsk(o)
(3)
tsk(o)
tsk(p) (4)
(1)
(2)
(3)
(4)
All typical values are at VDD = 2.5 V (unless otherwise noted), TA = 25°.
The propagation delay is the calculated RC time constant of the typical ON-State resistance of the switch and the specified load
capacitance when driven by an ideal voltage source (zero output impedance).
Output skew between center port to any other port.
Skew between opposite transitions of the same output in a given device |tPHL – tPLH|
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VDD = 2.5V ± 0.25 V, RL = 200 Ω, CL = 10 pF (unless otherwise
noted) (see Figure 9 and Figure 10)
TO
(OUTPUT)
tpd (2)
Dn
DA or DB
tPZH, tPZL
SEL
DA or DB
0.5
14
ns
tPHZ, tPLZ
SEL
DA or DB
0.9
15
ns
9
17
ns
SEL to switch turn on time
SEL to switch turn off time
tsk(o)
DA or DB
DA or DB
(3)
tsk(o)
tsk(p)
(1)
(2)
(3)
(4)
DA or DB
MIN
TYP (1)
FROM
(INPUT)
PARAMETER
MAX
149
UNIT
ps
5
18
ns
Dn (+)(-), DA(+)(-), DB(+)(-)
22
31
ps
Dn (all), DnA(all), DnB(All)
19
23
ps
22
33
ps
(4)
All typical values are at VDD = 2.5 V (unless otherwise noted), TA = 25°.
The propagation delay is the calculated RC time constant of the typical ON-State resistance of the switch and the specified load
capacitance when driven by an ideal voltage source (zero output impedance).
Output skew between center port to any other port.
Skew between opposite transitions of the same output in a given device |tPHL – tPLH|
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
5
TS3DV20812
SCDS302 – JUNE 2010
www.ti.com
DYNAMIC CHARACTERISTICS
over recommended operating free-air temperature range, VDD = 3.3 V ± 0.3 V, RL = 50 Ω, CL = 10 pF (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TYP
UNIT
XTALK
Differential crosstalk
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, see Figure 11
-34.67
dB
OIRR
Differential OFF isolation
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, see Figure 12
-19.09
dB
ILOSS
Differential insertion loss
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, seeFigure 13
-2.84
dB
IRETURN
Differential return loss
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, see Figure 13
-9.43
dB
DR
Data rate
2.20
Gbps
BW
Differential bandwidth
1.10
Ghz
DYNAMIC CHARACTERISTICS
over recommended operating free-air temperature range, VDD = 2.5 V ± 0.25 V, RL = 50 Ω, CL = 10 pF (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TYP
UNIT
XTALK
Differential crosstalk
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, see Figure 7
-34.94
dB
OIRR
Differential OFF isolation
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, see Figure 8
-18.39
dB
ILOSS
Differential insertion loss
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, see Figure 9
-3.07
dB
IRETURN
Differential return loss
825 MHz, 1.65Gbps, RL = 50 Ω, CL = 10 pF, see Figure 9
-9.56
dB
DR
Data rate
2.20
Gbps
BW
Differential bandwidth
1.10
Ghz
6
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
TYPICAL PERFORMANCE
Figure 1. Differential Gain vs Frequency
Figure 2. Differential Off Isolation vs Frequency
Figure 3. Differential Crosstalk vs Frequency
Figure 4. rON vs VCOM (Differential Switch)
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
7
TS3DV20812
SCDS302 – JUNE 2010
www.ti.com
APPLICATION INFORMATION
Figure 5. Typical Application Switching HDMI 1.2a and DVI
8
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
Figure 6. Typical Application for Dual LVDS
A.
The switch already has IOFF circuit and it will reduce the current flow leakage limit to 10 mA maximum and it will
prevent the damage from back drive current flow from the power-on circuit.
Figure 7. IOFF (Back Drive Protection)
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
9
TS3DV20812
SCDS302 – JUNE 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION
Figure 8. Differential Signaling Device
10
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 9. Test Circuit for Propagation Delay and Intra-Pair Skew
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
11
TS3DV20812
SCDS302 – JUNE 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 10. Test Circuit and Voltage Waveforms
12
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 11. Differential Crosstalk Test Circuit
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
13
TS3DV20812
SCDS302 – JUNE 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 12. Differential OFF Isolation Test Circuit
14
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
TS3DV20812
www.ti.com
SCDS302 – JUNE 2010
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 13. Differential Insertion Loss, Return Loss, and Common-Mode Insertion Loss Test Circuit
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TS3DV20812
15
PACKAGE OPTION ADDENDUM
www.ti.com
2-Jul-2010
PACKAGING INFORMATION
Orderable Device
TS3DV20812RHHR
Status
(1)
ACTIVE
Package Type Package
Drawing
VQFN
RHH
Pins
Package Qty
36
2500
Eco Plan
(2)
Green (RoHS
& no Sb/Br)
Lead/
Ball Finish
MSL Peak Temp
(3)
CU NIPDAU Level-3-260C-168 HR
Samples
(Requires Login)
Purchase Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jul-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TS3DV20812RHHR
Package Package Pins
Type Drawing
VQFN
RHH
36
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
16.4
Pack Materials-Page 1
6.3
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
6.3
1.5
12.0
16.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jul-2010
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TS3DV20812RHHR
VQFN
RHH
36
2500
346.0
346.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated